In situ X-ray diffraction studies of mixed LiMn2O4-LiNi1/3Co1/3Mn1/3O2 composite cathode in Li-ion cells during charge-discharge cycling

The structural changes of the composite cathode made by mixing spinel LiMn₂O₄ and layered LiNi_1/3Co_1/3Mn_1/3O₂ in 1:1 wt% in both Li-half and Li-ion cells during charge/discharge are studied by in situ XRD. During the first charge up to ∼5.2 V vs. Li/Li⁺, the in situ XRD spectra for the composite cathode in the Li-half cell track the structural changes of each component. At the early stage of charge, the lithium extraction takes place in the LiNi_1/3Co_1/3Mn_1/3O₂ component only. When the cell voltage reaches at ∼4.0 V vs. Li/Li⁺, lithium extraction from the spinel LiMn₂O₄ component starts and becomes the major contributor for the cell capacity due to the higher rate capability of LiMn₂O₄. When the voltage passed 4.3 V, the major structural changes are from the LiNi_1/3Co_1/3Mn_1/3O₂ component, while the LiMn₂O₄ component is almost unchanged. In the Li-ion cell using a MCMB anode and a composite cathode cycled between 2.5 V and 4.2 V, the structural changes are dominated by the spinel LiMn₂O₄ component, with much less changes in the layered LiNi_1/3Co_1/3Mn_1/3O₂ component, comparing with the Li-half cell results. These results give us valuable information about the structural changes relating to the contributions of each individual component to the cell capacity at certain charge/discharge state, which are helpful in designing and optimizing the composite cathode using spinel- and layered-type materials for Li-ion battery research.     

Cycle life improvement of ZrO2-coated spherical LiNi1/3Co1/3Mn1/3O2 cathode material for lithium ion batteries

A modified synthesis process was developed based on co-precipitation method followed by spray drying process. In this process, a spherical shaped (Co_1/3Ni_1/3Mn_1/3)(OH)₂ precursor was synthesized by co-precipitation and pre-heated at 500 °C to form a high structural stability spinel (CoNiMn)O₄ to maintain its shape for further processing. The spherical LiNi_1/3Co_1/3Mn_1/3O₂ was then prepared by spray drying process using spherical spinel (CoNiMn)O₄. LiNi_1/3Co_1/3Mn_1/3O₂ powders were then modified by coating their surface with a uniform and nano-sized layer of ZrO₂. The ZrO₂-coated LiNi_1/3Co_1/3Mn_1/3O₂ material exhibited an improved rate capability and cycling stability under a high cut-off voltage of 4.5 V. X-ray diffraction (XRD) measurements revealed that the material had a well-ordered layered structure and Zr was not doped into the LiNi_1/3Co_1/3Mn_1/3O₂. Electrochemical impedance spectroscopy measurements showed that the coated material has stable cell resistance regardless of cycle number. The interrupt charging/discharging test indicated that the ZrO₂ coating can suppress the polarization effects during the charging and discharging process. From these results, it is believed that the improved cycling performance of ZrO₂-coated LiNi_1/3Co_1/3Mn_1/3O₂ is attributed to the ability of ZrO₂ layer in preventing direct contact of the active material with the electrolyte resulting in a decrease of electrolyte decomposition reactions.     

Effect of Ag additive on the performance of LiNi1/3Co1/3Mn1/3O2 cathode material for lithium ion battery

The LiNi_1/3Co_1/3Mn_1/3O₂/Ag composite used for cathode material of lithium ion battery was prepared by thermal decomposition of AgNO₃ added to commercial LiNi_1/3Co_1/3Mn_1/3O₂ powders to improve the electrochemical performance of LiNi_1/3Mn_1/3Co_1/3O₂. Structure and morphology analysis showed that Ag particles were dispersed on the surface of LiNi_1/3Co_1/3Mn_1/3O₂ instead of entering the crystal structure. The results of charge–discharge tests showed that Ag additive could improve the cycle performance and high-rate discharge capability of LiNi_1/3Mn_1/3Co_1/3O₂. Extended analysis indicated that Ag was unstable in the commercial electrolyte at high potential. The improved electrochemical performance caused by Ag additive was associated not only with the enhancement of electrical conductivity of the material and the lower polarization of the cell, but also with the increased “c” parameter of LiNi_1/3Mn_1/3Co_1/3O₂ after repeated charge/discharge cycles and the compact and protective SEI layer formed on the surface of LiNi_1/3Mn_1/3Co_1/3O₂.     

Electrochemical performance of SrF2-coated LiNi1/3Co1/3Mn1/3O2 cathode materials for Li-ion batteries

SrF₂-coated LiNi_1/3Co_1/3Mn_1/3O₂ cathode materials with improved cycling performance over 2.5–4.6 V were investigated. The structural and electrochemical properties of the materials were studied using X-ray diffraction (XRD), scanning electron microscope (SEM), charge–discharge tests and electrochemical impedance spectra (EIS). The results showed that the crystalline SrF₂ with about 10–50 nm particle size is uniformly coated on the surface of LiNi_1/3Co_1/3Mn_1/3O₂ particles. As the coating amount increased from 0.0 to 2.0 mol%, the initial capacity and rate capability of the coated LiNi_1/3Co_1/3Mn_1/3O₂ decreased slightly owing to the increase of the charge-transfer resistance; however, the cycling stability was improved by suppressing the increase of the resistance during cycling. 4.0 mol% SrF₂-coated LiNi_1/3Co_1/3Mn_1/3O₂ showed remarkable decrease of the initial capacity. 2.0 mol% coated sample exhibited the best electrochemical performance. It presented an initial discharge capacity of 165.7 mAh g⁻¹, and a capacity retention of 86.9% after 50 cycles at 4.6 V cut-off cycling.     

Nonflammable electrolyte for 3-V lithium-ion battery with spinel materials LiNi0.5Mn1.5O4 and Li4Ti5O12

The compatibility between dimethyl methylphosphonate (DMMP)-based electrolyte of 1 M LiPF₆/EC + DMC + DMMP (1:1:2 wt.) and spinel materials Li₄Ti₅O₁₂ and LiNi_0.5Mn_1.5O₄ was reviewed, respectively. The cell performance and impedance of 3-V LiNi_0.5Mn_1.5O₄/Li₄Ti₅O₁₂ lithium-ion cell with the DMMP-based nonflammable electrolyte was compared with the baseline electrolyte of 1 M LiPF₆/EC + DMC (1:1 wt.). The nonflammable DMMP-based electrolyte exhibited good compatibility with spinel Li₄Ti₅O₁₂ anode and high-voltage LiNi_0.5Mn_1.5O₄ cathode, and acceptable cycling performance in the LiNi_0.5Mn_1.5O₄/Li₄Ti₅O₁₂ full-cell, except for the higher impedance than that in the baseline electrolyte. All of the results disclosed that the 3 V LiNi_0.5Mn_1.5O₄/Li₄Ti₅O₁₂ lithium-ion battery was a promising choice for the nonflammable DMMP-based electrolyte.     

Surface modification of LiNi0.5Mn1.5O4 by ZrP2O7 and ZrO2 for lithium-ion batteries

The spinel LiNi_0.5Mn_1.5O₄ has been surface modified separately with 1.0 wt.% ZrO₂ and ZrP₂O₇ for the purpose of improving its cycle performance as a cathode in a 5-V lithium-ion cell. Although the modifications did not change the crystallographic structure of the surface-modified samples, they exhibited better cyclability at elevated temperature (55 °C) compared with pristine LiNi_0.5Mn_1.5O₄. The material that was surface modified with ZrO₂ gave the best cycling performance, only 4% loss of capacity after 150 cycles at 55 °C. Electrochemical impedance spectroscopy demonstrated that the improved performance of the ZrO₂-surface-modified LiNi_0.5Mn_1.5O₄ is due to a small decrease in the charge transfer resistance, indicating limited surface reactivity during cycling. Differential scanning calorimetry showed that the ZrO₂-modified LiNi_0.5Mn_1.5O₄ exhibits lower heat generation and higher onset reaction temperature compared to the pristine material. The excellent cycling and safety performance of the ZrO₂-modified LiNi_0.5Mn_1.5O₄ electrode was found to be due to the protective effect of homogeneous ZrO₂ nano-particles that form on the LiNi_0.5Mn_1.5O₄, as shown by transmission electron microscopy.     

Synthesis of LiNi1/3Co1/3Mn1/3O2 as a cathode material for lithium battery by the rheological phase method

LiNi_1/3Co_1/3Mn_1/3O₂ is prepared by a rheological phase method. Homogeneous precursor derived from this method is calcined at 800 °C for 20 h in air, which results in the impressive differences in the morphology properties and electrochemical behaviors of LiNi_1/3Co_1/3Mn_1/3O₂ in contrast to that obtained by a solid-state method. The microscopic structural features of LiNi_1/3Co_1/3Mn_1/3O₂ are investigated using scanning electron microscopy (SEM), X-ray diffraction (XRD). The electrochemical properties of LiNi_1/3Co_1/3Mn_1/3O₂ are carried out by charge–discharge cycling test. All experiments show that the microscopic structural features and the morphology properties are deeply related with the electrochemical performances. The obtained results suggest that the rheological phase method may become an effective route to prepare LiNi_1/3Co_1/3Mn_1/3O₂ cathode materials for lithium battery.     

Thermal and electrochemical characterization of MCMB/LiNi1/3Co1/3Mn1/3O2 using LiBoB as an electrolyte additive

The gas generation associated with the use of the lithium bis(oxalate)borate—(LiBoB) based electrolyte at the elevated temperature were detected in the pouch cell (MCMB/LiNi_1/3Co_1/3Mn_1/3O₂ with 10% excess Li), which might prevent the LiBoB usage as a salt. However, the cell capacity retention was improved significantly, from 87 to 96% at elevated temperature, when using LiBoB as an electrolyte additive. The capacity fade during cycling is discussed using dQ/dE, area specific impedance, and frequency response analysis results. Most of the capacity loss in the cell is associated with the rise in the cell impedance. Moreover, results from the differential scanning calorimetry indicate that the thermal stability of the negative electrode with the solid electrolyte interface (SEI) formed by the reduction of the LiBoB additive was greatly improved compared with that obtained from the reduction of LiPF₆-based electrolyte without additive. In this case, the onset temperature of the breakdown of the LiBoB-based SEI is 150 °C which is higher than that of the conventional electrolyte without additive. Furthermore, the total heat generated between 60 and 170 °C is reduced from 213 to 70 J g⁻¹ when using LiBoB as electrolyte additive compared to the one without additive. In addition, the thermal stability of the charged LiNi_1/3Co_1/3Mn_1/3O₂ with 10% excess Li was not affected when using LiBoB as an electrolyte additive.     

Preparation and electrochemical properties of Li[Ni1/3Co1/3Mn1−x/3Zrx/3]O2 cathode materials for Li-ion batteries

Layer-structured Zr doped Li[Ni_1/3Co_1/3Mn_1−x/3Zr_x/3]O₂ (0 ≤ x ≤ 0.05) were synthesized via slurry spray drying method. The powders were characterized by XRD, SEM and galvanostatic charge/discharge tests. The products remained single-phase within the range of 0 ≤ x ≤ 0.03. The charge and discharge cycling of the cells showed that Zr doping enhanced cycle life compared to the bare one, while did not cause the reduction of the discharge capacity of Li[Ni_1/3Co_1/3Mn_1/3]O₂. The unchanged peak shape in the differential capacity versus voltage curve suggested that the Zr had the effect to stabilize the structure during cycling. More interestingly, the rate capability was greatly improved. The sample with x = 0.01 presented a capacity of 160.2 mAh g⁻¹ at current density of 640 mA g⁻¹(4 C), corresponding to 92.4% of its capacity at 32 mA g⁻¹(0.2 C). The favorable performance of the doped sample could be attributed to its increased lattice parameter.     

Electrochemical performance of nanostructured spinel LiMn2O4 in different aqueous electrolytes

A nanostructured spinel LiMn₂O₄ electrode material was prepared via a room-temperature solid-state grinding reaction route starting with hydrated lithium acetate (LiAc·2H₂O), manganese acetate (MnAc₂·4H₂O) and citric acid (C₆H₈O₇·H₂O) raw materials, followed by calcination of the precursor at 500 °C. The material was characterized by X-ray diffraction (XRD) and transmission electron microscope techniques. The electrochemical performance of the LiMn₂O₄ electrodes in 2 M Li₂SO₄, 1 M LiNO₃, 5 M LiNO₃ and 9 M LiNO₃ aqueous electrolytes was studied using cyclic voltammetry, ac impedance and galvanostatic charge/discharge methods. The LiMn₂O₄ electrode in 5 M LiNO₃ electrolyte exhibited good electrochemical performance in terms of specific capacity, rate dischargeability and charge/discharge cyclability, as evidenced by the charge/discharge results.     

Study of the surface modification of LiNi1/3Co1/3Mn1/3O2 cathode material for lithium ion battery

The surface of LiNi_1/3Co_1/3Mn_1/3O₂ (LNMCO) particles has been studied for material synthesized at 900 °C by a two-step process from a mixture of LiOH·H₂O and metal oxalate [(Ni_1/3Co_1/3Mn_1/3)C₂O₄] obtained by co-precipitation. Samples have been characterized by X-ray diffraction (XRD), high-resolution transmission electron microscope (HRTEM), Raman scattering (RS) spectroscopy, and magnetic measurements. We have investigated the effect of the heat treatment of particles at 600 °C with organic substances such as sucrose and starch. HRTEM images and RS spectra indicate that the surface of particles has been modified. The annealing does not lead to any carbon coating but it leads to the crystallization of the thin disordered layer on the surface of LiNi_1/3Co_1/3Mn_1/3O₂. The beneficial effect has been tested on the electrochemical properties of the LiNi_1/3Co_1/3Mn_1/3O₂ cathode materials. The capacity at 10C-rate is enhanced by 20% for post-treated LNMCO particles at 600 °C for half-an-hour.     

Investigation of LiNi1/3Co1/3Mn1/3O2 cathode particles after 300 discharge/charge cycling in a lithium-ion battery by analytical TEM

Using analytical transmission electron microscopy (TEM) techniques reveal a zigzag layer on surface of the cycled particles of LiNi_1/3Co_1/3Mn_1/3O₂ cathode after 300 discharge/charge cycles. The Ni, Mn content in the zigzag layer of the cycled particle has decreased rapidly from interior to edge of the zigzag layer of the cycled particles. The structure of LiNi_1/3Co_1/3Mn_1/3O₂ oxide was gradually destructed from hexagonal cell with P3₁12 at interior region to fcc lattice of α-NaFeO₂ at edge of the zigzag layer of the cycled particles. These experimental data provide the compositional and structural origins of the capacity decrease in the Li-ion battery.     

Effect of NaI/I2 mediators on properties of PEO/LiAlO2 based all-solid-state supercapacitors

NaI/I₂ mediators and activated carbon were added into poly(ethylene oxide) (PEO)/lithium aluminate (LiAlO₂) electrolyte to fabricate composite electrodes. All solid-state supercapacitors were fabricated using the as prepared composite electrodes and a Nafion 117 membrane as a separator. Cyclic voltammetry, electrochemical impedance spectroscopy, and galvanostatic charge/discharge measurements were conducted to evaluate the electrochemical properties of the supercapacitors. With the addition of NaI/I₂ mediators, the specific capacitance increased by 27 folds up to 150 F g⁻¹. The specific capacitance increased with increases in the concentration of mediators in the electrodes. The addition of mediators also reduced the electrode resistance and rendered a higher electron transfer rate between mediator and mediator. The stability of the all-solid-state supercapacitor was tested over 2000 charge/discharge cycles.     

Morphology and electrochemical performance of Li[Ni1/3Co1/3Mn1/3]O2 cathode material by a slurry spray drying method

The spherical Li[Ni_1/3Co_1/3Mn_1/3]O₂ powders with appropriate porosity, small particle size and good particle size distribution were successfully prepared by a slurry spray drying method. The Li[Ni_1/3Co_1/3Mn_1/3]O₂ powders were characterized by XRD, SEM, ICP, BET, EIS and galvanostatic charge/discharge testing. The material calcined at 950 °C had the best electrochemical performance. Its initial discharge capacity was 188.9 mAh g⁻¹ at the discharge rate of 0.2 C (32 mA g⁻¹), and retained 91.4% of the capacity on going from 0.2 to 4 C rate. From the EIS result, it was found that the favorable electrochemical performance of the Li[Ni_1/3Co_1/3Mn_1/3]O₂ cathode material was primarily attributed to the particular morphology formed by the spray drying process which was favorable for the charge transfer during the deintercalation and intercalation cycling.     

A novel method for synthesis of layered LiNi1/3Mn1/3Co1/3O2 as cathode material for lithium-ion battery

The layered LiNi_1/3Mn_1/3Co_1/3O₂ materials with good crystalline are synthesized by a novel method of hydrothermal method followed by a short calcination process. The crystalline structure and morphology of the synthesized materials are characterized by XRD, SEM. Their electrochemical performances are evaluated by CV, EIS and galvonostatic charge/discharge tests. The material synthesized at 850 °C for 6 h shows the highest initial discharge capacity of 187.7 mAh g⁻¹ at 20 mA g⁻¹. And the capacity retention of 97.9% is maintained at the end of 40 cycles at 1.0 C. CV test reveals almost no shift of anodic and cathodic peaks after first cycle, which indicates good reversible deintercalation and intercalation of Li⁺ ions.     

Effect of equivalent and non-equivalent Al substitutions on the structure and electrochemical properties of LiNi0.5Mn0.5O2

Pristine, equivalently and non-equivalently Al substituted LiNi_0.5Mn_0.5O₂ materials were prepared by a combination of co-precipitation and solid-state reaction. As shown by XRD and XPS, lattice volume shrinkage of LiNi_0.5(Mn_0.45Al_0.05)O₂ was attributed to the presence of Ni in both 2+ and 3+, while the lattice volume expansion of Li(Ni_0.45Al_0.05)Mn_0.5O₂ was caused by lowering the average oxidation state of Mn. Electrochemical performance of LiNi_0.5Mn_0.5O₂ materials can be greatly affected by the change of oxidation states of the transition metals by Al substitution. Non-equivalent substitution of Al for Ni leads to deteriorated discharge performance and cyclic stability due to the reduction of the electrochemical active Ni²⁺ and structure supported Mn⁴⁺, while an increase in the amount of Ni²⁺ in LiNi_0.5(Mn_0.45Al_0.05)O₂ brings obvious improvement of the electrochemical properties. EIS analyses of the electrode materials at pristine and charged states indicate that the poor electrochemical performance of Li(Ni_0.45Al_0.05)Mn_0.5O₂ material can be ascribed to the higher charge transfer resistance and surface film resistance, and the observed higher current rate capability of LiNi_0.5(Mn_0.45Al_0.05)O₂ can be understood due to the better charge transfer kinetics.     

Mechanistic study on lithium intercalation using a restricted reaction field in LiNi0.5Mn0.5O2

Structure changes of LiNi_0.5Mn_0.5O₂ were detected at the electrode/electrolyte interface of lithium cell using synchrotron X-ray scattering and two-dimensional model electrodes. The electrodes were constructed by an epitaxial film of LiNi_0.5Mn_0.5O₂ synthesized by pulsed laser deposition (PLD) method. The orientation of the film depends on the substrate plane; the 2D layer of LiNi_0.5Mn_0.5O₂ is parallel to the SrTiO₃(1 1 0) substrate ((1 1 0) LiNi_0.5Mn_0.5O₂//(1 1 0) SrTiO₃), while the 2D layer is perpendicular to the SrTiO₃(1 1 1) substrate ((0 0 3) LiNi_0.5Mn_0.5O₂//(1 1 1) SrTiO₃). The in situ X-ray diffraction of LiNi_0.5Mn_0.5O₂(0 0 3) confirmed three-dimensional lithium diffusion through the two-dimensional transition meal layers. The intercalation reaction of LiNi_0.5Mn_0.5O₂ will be discussed.     

Charge–discharge characteristics of all-solid-state thin-filmed lithium-ion batteries using amorphous Nb2O5 negative electrodes

All-solid-state thin-filmed lithium-ion rechargeable batteries composed of amorphous Nb₂O₅ negative electrode with the thickness of 50–300 nm and amorphous Li₂Mn₂O₄ positive electrode with a constant thickness of 200 nm, and amorphous Li₃PO_4−xN_x electrolyte (100 nm thickness), have been fabricated on glass substrates with a 50 mm × 50 mm size by a sputtering method, and their electrochemical characteristics were investigated. The charge–discharge capacity based on the volume of positive electrode increased with increasing thickness of negative electrode, reaching about 600 mAh cm⁻³ for the battery with the negative electrode thickness of 200 nm. But the capacity based on the volume of both the positive and negative electrodes was the maximum value of about 310 mAh cm⁻³ for the battery with the negative electrode thickness of 100 nm. The shape of charge–discharge curve consisted of a two-step for the batteries with the negative electrode thickness more than 200 nm, but that with the thickness of 100 nm was a smooth S-shape curve during 500 cycles.     

Synthesis and characterization of submicron-sized LiNi1/3Co1/3Mn1/3O2 by a simple self-propagating solid-state metathesis method

Submicron-sized LiNi_1/3Co_1/3Mn_1/3O₂ cathode materials were synthesized using a simple self-propagating solid-state metathesis method with the help of ball milling and the following calcination. A mixture of Li(ac)·2H₂O, Ni(ac)₂·4H₂O, Co(ac)₂·4H₂O, Mn(ac)₂·4H₂O (ac = acetate) and excess H₂C₂O₄·2H₂O was used as starting material without any solvent. XRD analyses indicate that the LiNi_1/3Co_1/3Mn_1/3O₂ materials were formed with typical hexagonal structure. The FESEM images show that the primary particle size of the LiNi_1/3Co_1/3Mn_1/3O₂ materials gradually increases from about 100 nm at 700 °C to 200–500 nm at 950 °C with increasing calcination temperature. Among the synthesized materials, the LiNi_1/3Co_1/3Mn_1/3O₂ material calcined at 900 °C exhibits excellent electrochemical performance. The steady discharge capacities of the material cycled at 1 C (160 mA g⁻¹) rate are at about 140 mAh g⁻¹ after 100 cycles in the voltage range 3–4.5 V (versus Li⁺/Li) and the capacity retention is about 87% at the 350th cycle.     

Investigation on the charging process of Li2O2-based air electrodes in Li-O2 batteries with organic carbonate electrolytes

The charging process of Li₂O₂-based air electrodes in Li-O₂ batteries with organic carbonate electrolytes was investigated using in situ gas chromatography/mass spectroscopy (GC/MS) to analyze gas evolution. A mixture of Li₂O₂/Fe₃O₄/Super P carbon/polyvinylidene fluoride (PVDF) was used as the starting air electrode material, and 1-M lithium bis(trifluoromethylsulfonyl)imide (LiTFSI) in carbonate-based solvents was used as the electrolyte. We found that Li₂O₂ was actively reactive to 1-methyl-2-pyrrolidinone and PVDF that were used to prepare the electrode. During the first charging (up to 4.6 V), O₂ was the main component in the gases released. The amount of O₂ measured by GC/MS was consistent with the amount of Li₂O₂ that decomposed during the electrochemical process as measured by the charge capacity, which is indicative of the good chargeability of Li₂O₂. However, after the cell was discharged to 2.0 V in an O₂ atmosphere and then recharged to ∼4.6 V, CO₂ was dominant in the released gases. Further analysis of the discharged air electrodes by X-ray diffraction (XRD) and Fourier transform infrared (FTIR) spectroscopy indicated that lithium-containing carbonate species (lithium alkyl carbonates and/or Li₂CO₃) were the main discharge products. Therefore, compatible electrolytes and electrodes, as well as the electrode-preparation procedures, need to be developed for rechargeable Li-air batteries for long term operation.