H13淬硬模具钢精车过程的数值模拟

采用热力学耦合有限元方法研究了淬硬钢精车过程中切屑形成规律。运用H13 淬硬模具钢流动应力模型进行数值模拟,考查了H13淬硬模具钢精车过程中工艺参数对工件性能和刀具的影响。结果表明:切削速度愈高,进给量愈小,刀具刀尖半径愈大,则工件加工层上的静水拉应力愈小,表面质量愈好; 淬硬钢精车时径向力起主要作用,大于切削力;切削速度愈大,切削力和径向力则愈小,愈有助于改善工件加工层上的表面质量;切削速度、进给量和刀具刀尖圆角半径愈大,工件和刀具温度愈高,愈易导致刀具前刀面扩散磨损和刀具后刀面磨损。研究结论有助于优化H13淬硬模具钢精车过程中工艺参数选择和改进刀具镶片设计。     

Size effect and tool geometry in micromilling of tool steel

The market for freeform and high quality microdies and moulds made of steel is predicted to experience a phenomenal growth in line with the demand for microsystems. However, micromachining of hardened steel is a challenge due to unpredictable tool life and likely differences in process mechanism compared to macro-scale machining. This paper presents an investigation of the size effect in micromilling of H13 hardened tool steel. In this case, the size effect in micromilling hardened tool steel was observed by studying the effect of the ratio of undeformed chip thickness to the cutting edge radius on process performance. The paper explores how this ratio drives the specific cutting force, surface finish and burr formation in micro-scale machining. In addition, the effect of different microend mill geometry on product quality was explored. The paper provides a valuable insight into optimum micro-scale machining conditions for obtaining the best surface finish and minimizing burr size.     

Analysis and prediction of tool wear, surface roughness and cutting forces in hard turning with CBN tool

The main of the present study is to investigate the effects of process parameters (cutting speed, feed rate and depth of cut) on performance characteristics (tool life, surface roughness and cutting forces) in finish hard turning of AISI 52100 bearing steel with CBN tool. The cutting forces and surface roughness are measured at the end of useful tool life. The combined effects of the process parameters on performance characteristics are investigated using ANOVA. The composite desirability optimization technique associated with the RSM quadratic models is used as multi-objective optimization approach. The results show that feed rate and cutting speed strongly influence surface roughness and tool life. However, the depth of cut exhibits maximum influence on cutting forces. The proposed experimental and statistical approaches bring reliable methodologies to model, to optimize and to improve the hard turning process. They can be extended efficiently to study other machining processes.     

Some studies on hard turning of AISI 4340 steel using multilayer coated carbide tool

Hard turning with multilayer coated carbide tool has several benefits over grinding process such as, reduction of processing costs, increased productivities and improved material properties. The objective was to establish a correlation between cutting parameters such as cutting speed, feed rate and depth of cut with machining force, power, specific cutting force, tool wear and surface roughness on work piece. In the present study, performance of multilayer hard coatings (TiC/TiCN/Al₂O₃) on cemented carbide substrate using chemical vapor deposition (CVD) for machining of hardened AISI 4340 steel was evaluated. An attempt has been made to analyze the effects of process parameters on machinability aspects using Taguchi technique. Response surface plots are generated for the study of interaction effects of cutting conditions on machinability factors. The correlations were established by multiple linear regression models. The linear regression models were validated using confirmation tests. The analysis of the result revealed that, the optimal combination of low feed rate and low depth of cut with high cutting speed is beneficial for reducing machining force. Higher values of feed rates are necessary to minimize the specific cutting force. The machining power and cutting tool wear increases almost linearly with increase in cutting speed and feed rate. The combination of low feed rate and high cutting speed is necessary for minimizing the surface roughness. Abrasion was the principle wear mechanism observed at all the cutting conditions.     

Tool vibration in internal turning of hardened steel using cBN tool

The machining of hardened materials with hardness over 45 HRC has been an alternative to grinding since the 1970s, with the commercial availability of cubic boron nitride (cBN) and ceramic tools. However, the low toughness of these types of tool materials makes them very sensitive to damages caused by vibrations, which are critical for operations like internal turning, where the tool resembles a cantilever beam and therefore is susceptible to large deflections. This work aims to contribute to the study of tool performance in internal turning of long holes in hardened AISI 4340 steel in finishing conditions. Different machining conditions, two different tool holders (steel and carbide), and several tool overhangs were tested. The surface finish, acceleration (vibration) signals, and tool wear of cBN inserts were evaluated. The results show that vibration and the material of the tool holder may play a secondary role in the surface finish for stable turning, but the use of carbide tool holders makes the process stable for longer tool overhangs. Moreover, when the cutting becomes unstable, surface roughness is increased severely.     

Machinability investigation in hard turning of AISI D3 cold work steel with ceramic tool using response surface methodology

The hard turning process has been attracting interest in different industrial sectors for finishing operations of hard materials. In this paper, the effects of cutting speed, feed rate, and depth of cut on surface roughness, cutting force, specific cutting force, and power in the hard turning were experimentally investigated. An experimental investigation was carried out using ceramic cutting tools, composed approximately with (70 %) of Al₂O₃ and (30 %) of TiC, in surface finish operations on cold work tool steel AISI D3 heat-treated to a hardness of 60 HRC. Based on 3³ full factorial designs, a total of 27 tests were carried out. The range of each parameter is set at three different levels, namely, low, medium, and high. Analysis of variance is used to check the validity of the model. Experimental observations show that higher cutting forces are required for machining harder work material. This cutting force gets affected mostly by feed rate followed by depth of cut. Feed rate is the most influencing factor on surface roughness. Feed rate followed by depth of cut become the most influencing factors on power; especially in case of harder workpiece. Optimum cutting conditions are determined using response surface methodology (RSM) and the desirability function approach. It was found that, the use of lower depth of cut value, higher cutting speed, and by limiting the feed rate to 0.12 and 0.13 mm/rev, while hard turning of AISI D3 hardened steel, respectively, ensures minimum cutting forces and better surface roughness. Higher values of depth of cut are necessary to minimize the specific cutting force.     

Modelling the effects of cutting parameters on residual stresses in hard turning of AISI H11 tool steel

In the present study, an attempt has been made to model the effect of cutting parameters (cutting speed, feed, depth of cut and nose radius) on residual stresses in hard turning of AISI H11 tool steel using ceramic tools. The machining experiments were conducted based on response surface methodology and using the Box–Behnken design of experiments. Residual stresses were determined using the X-ray diffraction technique, and the experimental results were investigated using analysis of variance. The results indicated that the feed and depth of cut are the main influencing factor on residual stresses whereas cutting speed and nose radius are having mild impact on residual stresses. The results show that it is possible to produce tailor-made residual stress levels by controlling the tool geometry and cutting parameters. The aim of this paper is to introduce an original approach for the prediction of residual stresses.     

Experimental investigation of surface roughness and cutting ratio in a spraying cryogenic turning process

Abstract

Surface roughness is one of the most common criteria indicating the surface finish of the part, which depends on various factors including cutting parameters, geometry of the tool, and cutting fluid. One of the goals of using cutting fluids in machining processes is to achieve improved surface finish. In addition to high costs, commonly used cutting fluids cause dermal and respiratory problems to the operators as well as environmental pollution. The present article aims at investigating the effect of spray cryogenic cooling via liquid nitrogen on surface roughness and cutting ratio in turning process of AISI 304 stainless steel. Through conducting experimental tests, the effects of cutting speed, feed rate, and depth of cut on surface roughness and cutting ratio have been compared in dry and cryogenic turning. A total number of 72 tests have been carried out. Results show that cryogenic turning of AISI 304 stainless steel reduces surface roughness 1%–27% (13% on the average), compared to dry turning. The obtained results showed that the cutting ratio in cryogenic turning is averagely increased by 32% in comparison with dry turning, also that chip breakage is improved in cryogenic turning.     

Modelling of CBN tool crater wear in finish hard turning

The wear of cubic boron nitride (CBN) cutters, commonly used now in the finish turning of hardened parts, is an important issue that needs to be addressed for hard turning to be a viable technology due to the high costs of CBN cutters and the down-time for tool change. Chipping and tool breakage, which lead to early tool failure, are both prone to take place under the effect of crater wear. The objective of this study is to develop a methodology to model the CBN tool crater wear rate to both guide the design of CBN tool geometry and optimise cutting parameters in finish hard turning. First, the wear volume losses due to the main wear mechanisms (abrasion, adhesion, and diffusion) are modelled as functions of cutting temperature, stress, and other process attributes respectively. Then, the crater wear rate is predicted in terms of tool/work material properties and cutting configuration. Finally, the proposed model is experimentally validated in finish turning of hardened 52100 bearing steel using a low CBN content insert. The comparison between the prediction and the measurement shows reasonable agreement and the results suggest that adhesion is the main wear mechanism over the investigated range of cutting conditions .     

切削速度对精密干式车削淬硬工具钢切削力的影响

通过使用PCBN刀具精密干式车削淬硬Cr12MoV工具钢(62±1 HRC)的试验,分析了切削速度对三向切削力的影响,得出了最优切削速度。试验表明:随切削速度提高,三向切削力先急剧增大,后急剧减小,再又缓慢增大。若从最小车削合力与提高加工效率两个角度来优化切削速度,则226 n/min是最优切削速度。试验结果也对精密干式切削淬硬工具钢具有实际指导意义与参考价值。     

Feasibility of mild hard turning of stainless steel using coated carbide tool

Hard turning has been explored as an alternative to the traditional processing technique used to manufacture parts made of hardened steels. However, advanced cutting tool materials for hard turning applications are relatively expensive. The continuous developments in carbide tool material and its coating technology have offered inexpensive cutting tool alternatives for a mild range of hard turning operations. Commercially available TiAlN-coated carbide tool is utilized in this study to perform hard turning of stainless steel within the mild range (47–48 HRC) at various cutting parameters, i.e., cutting speed and feed. Empirical models to measure its performance by quantifying the effect of the cutting parameters to the tool’s service lifetime and the machined workpiece’s surface roughness are developed. The coated carbide tool performed hard turning with fair tool life and fine surface finish, especially at low cutting parameters as shown by the models’ solutions for the optimized input selection.     

Tool crater wear depth modeling in CBN hard turning

Hard turning has been receiving increased attention because it offers many possible benefits over grinding in machining hardened steel. The wear of cubic boron nitride (CBN) tools, which are commonly used in hard turning, is an important issue that needs to be better understood. For hard turning to be a viable replacement technology, the high cost of CBN cutting tools and the cost of down-time for tool changing must be minimized. In addition to progressive flank wear, microchipping and tool breakage (which lead to early tool failure) are prone to occur under aggressive machining conditions due to significant crater wear and weakening of the cutting edge. The objective of this study is to model the CBN tool crater wear depth (K_T) to guide the design of CBN tool geometry and to optimize cutting parameters in finish hard turning. First, the main wear mechanisms (abrasion, adhesion, and diffusion) in hard turning are discussed and the associated wear volume loss models are developed as functions of cutting temperature, stress, and other process information. Then, the crater wear depth is predicted in terms of tool/work material properties and process information. Finally, the proposed model is experimentally validated in finish turning of hardened 52100 bearing steel using a low CBN content tool. The comparison between model predictions and experimental results shows reasonable agreement, and the results suggest that adhesion is the dominant wear mechanism within the range of conditions that were investigated.     

Performance studies of multilayer hard surface coatings (TiN/TiCN/Al2O3/TiN) of indexable carbide inserts in hard machining: Part-I (An experimental approach)

In recent years, hard machining using CBN and ceramic inserts became an emerging technology than traditional grinding and widely used manufacturing processes. However the relatively high cost factors associated with such tools has left a space to look for relatively low cost cutting tool materials to perform in an acceptable range. Multilayer coated carbide insert is the proposed alternative in the present study due to its low cost. Thus, an attempt has been made to have an extensive study on the machinability aspects such as flank wear, chip morphology, surface roughness in finish hard turning of AISI 4340 steel (HRC 47 ± 1) using multilayer coated carbide (TiN/TiCN/Al₂O₃/TiN) insert under dry environment. Parametric influences on turning forces are also analyzed. From the machinability study, abrasion and chipping are found to be the dominant wear mechanism in hard turning. Multilayer TiN coated carbide inserts produced better surface quality and within recommendable range of 1.6 μm i.e. comparable with cylindrical grinding. At extreme parametric conditions, the growth of tool wear was observed to be rapid thus surface quality affected adversely. The chip morphology study reveals a more favorable machining environment in dry machining using TiN coated carbide inserts. The cutting speed and feed are found to have the significant effect on the tool wear and surface roughness from ANOVA study. It is evident that, thrust force (Fy) is the largest component followed by tangential force (Fz) and the feed force (Fx) in finish hard turning. The observations yield the machining ability of multilayer TiN coated carbide inserts in hard turning of AISI 4340 steel even at higher cutting speeds.     

Influence of tool wear on surface roughness in hard turning using differently shaped ceramic tools

Hard turning has been applied in many cases in producing bearings, gears, cams, shafts, axels, and other mechanical components since the early 1980s. Mixed ceramics (aluminum oxide plus TiC or TiCN) is one of the two cutting tool materials (apart from PCBN) widely used for finish machining of hardened steel (HRC 50–65) parts, especially under dry machining conditions and moderate cutting speed ranging from 90 to 120 m/min. This paper reports an extensive characterization of the surface roughness generated during hard turning (HT) operations performed with conventional and wiper ceramic tools at variable feed rate and its changes originated from tool wear. Moreover, it compares some predominant tool wear patterns produced on the two types of ceramic inserts and their influence on the alteration of surface profiles. After the hard turning tests, the relevant changes of surface profiles and surface roughness parameters were successively registered and measured by a stylus profilometer. In this investigation, a set of 2D surface roughness parameters, as well as profile and surface characteristics, such as the amplitude distribution functions, bearing area curves and symmetrical curves of geometrical contact obtained for the machined surface, were determined and analyzed. A novel aspect of this research is that the notch wear progress at the secondary cutting (trailing) edges was found to produce the substantial modifications of the individual irregularities, and constitute the altered surface profiles. Moreover, this research contributes to practical aspects of HT technology due to exploring the relations between the tool state at different times within the tool life and the relevant surface roughness characterization.     

Finite element modeling and simulation in dry hard orthogonal cutting AISI D2 tool steel with CBN cutting tool

The influences of cutting parameters on temperature, stress, and shear angle during dry hard orthogonal cutting (DHOC) of D2 tool steel (62?±?1 HRC) are investigated in this paper. Temperature and stress are considered the most important aspects to be taken into account in dry hard machining; however, dry hard machining is a complex process, and the temperature fields and residual stress are the most difficult to be measured. Up to now, only very few studies have been reported on influences of cutting parameters on shear angle, temperature, and stress of AISI D2 tool steel (62?±?1 HRC). In this paper, the Johnson–Cook model is utilized to propose a finite element (FE) model. The FE model is properly calibrated by means of an iterative procedure based on the comparison between experimental resultant forces obtained from literatures and simulated resultant forces. At last, this FE model is utilized to predict the influences of cutting speed and depth of cut on temperature fields and residual stress within a workpiece, cutting tool edge temperature, and shear angle during DHOC hardened AISI D2 tool steel (62?±?1 HRC) and validated by experimental results. As shown in this investigation, it is also possible to properly analyze the influences of cutting parameters on the cutting mechanism for industrial application.     

Performance comparison of conventional and wiper ceramic inserts in hard turning through artificial neural network modeling

Hard turning with ceramic tools provides an alternative to grinding operation in machining high precision and hardened components. But, the main concerns are the cost of expensive tool materials and the effect of the process on machinability. The poor selection of cutting conditions may lead to excessive tool wear and increased surface roughness of workpiece. Hence, there is a need to investigate the effects of process parameters on machinability characteristics in hard turning. In this work, the influence of cutting speed, feed rate, and machining time on machinability aspects such as specific cutting force, surface roughness, and tool wear in AISI D2 cold work tool steel hard turning with three different ceramic inserts, namely, CC650, CC650WG, and GC6050WH has been studied. A multilayer feed-forward artificial neural network (ANN), trained using error back-propagation training algorithm has been employed for predicting the machinability. The input?Coutput patterns required for ANN training and testing are obtained from the turning experiments planned through full factorial design. The simulation results demonstrate the effectiveness of ANN models to analyze the effects of cutting conditions as well as to study the performance of conventional and wiper ceramic inserts on machinability.     

Studies on wears of ultrafine-grained ceramic tool and common ceramic tool during hard turning using Archard wear model

Hardened steels are difficult to be machined due to their high tensile strength and work-hardening rate, low thermal conductivity, and abrasive behavior. In this paper, finite element modeling (FEM) approaches with lagrangian increment method for 3D metal turning of hardened steel H13 by common ceramic tool and ultrafine-grained tool respectively have been investigated by simulation of DEFORM-3D software and turning test. Conditions of initial and boundary and turning process parameters have been chosen. Material properties of H13 and ceramic have been described in details. Johnson–Cook model of H13 model has been applied to the hard turning modeling. Archard wear model has been built, and the correlation coefficients were decided by reciprocating friction experiments. The simulation results showed that predicted primary turning force and maximum temperature in common ceramic are bigger than which was caused by ultrafine-grained ceramic tool for the ultrafine-grained ceramic tools have better thermal stability and bigger hardness. The wear depths of common ceramic tool are about many times than that of ultrafine-grained ceramic tool according to the simulation and experimental results. And their wear patterns are very different. The FEM simulation results have entirely explicated experimental results. The obtained results would provide the fundamental and practical guidelines of tool material choice for hard turning.     

精密干式硬态车削淬硬工具钢时表面粗糙度的参数优化

使用PCBN刀具对不同淬硬状态工具钢Cr12MoV进行了精密干式硬态车削试验,运用正交实验法分析了切削速度、试件硬度、刀具前角、切削深度4个因素间的交互作用,并得到了最优车削参数.试验表明:影响表面粗糙度最显著的因素是切削速度与淬火硬度,切削深度影响最小.     

Analysis of tool wear and surface finish in hard turning

Hard turning is a profitable alternative to finish grinding. The ultimate aim of hard turning is to remove work piece material in a single cut rather than a lengthy grinding operation in order to reduce processing time, production cost, surface roughness, and setup time, and to remain competitive. In recent years, interrupted hard turning, which is the process of turning hardened parts with areas of interrupted surfaces, has also been encouraged. The process of hard turning offers many potential benefits compared to the conventional grinding operation. Additionally, tool wear, tool life, quality of surface turned, and amount of material removed are also predicted. In this analysis, 18 different machining conditions, with three different grades of polycrystalline cubic boron nitride (PCBN), cutting tool are considered. This paper describes the various characteristics in terms of component quality, tool life, tool wear, effects of individual parameters on tool life and material removal, and economics of operation. The newer solution, a hard turning operation, is performed on a lathe. In this study, the PCBN tool inserts are used with a WIDAX PT GNR 2525 M16 tool holder. The hardened material selected for hard turning is commercially available engine crank pin material.     

Analysis model of parameters affecting cutting performance in high-speed machining

Further progress in green cutting applications depends on the innovativeness of machine tools, advances in tool development, and, especially, more complex tool and cutting technologies. Therefore, this study analyzes the factors influencing high-speed cutting performance. Grey relational analysis and the Taguchi method are then incorporated in the experimental plan with high-speed milling of AISI H13 tool steel. Experimental results indicate that the contributions of tool grinding precision, geometric angle, and cutting conditions to the multiple quality characteristics of high-speed milling for AISI H13 tool steel are 11.75, 9.80, and 73.11 %, respectively. For rough machining, tool life and metal removal volume are the primary evaluation indicators and cutting parameters should be prioritized, especially cutting speed and feed per tooth. In finish machining, workpiece surface roughness is the primary evaluation indicator. Besides the selection of cutting parameters, the design and grinding of endmill are critical factors, especially the design and grinding of relief angles.