Effect of hydrogen on reaction intermediates in the selective catalytic reduction of NOx by C3H6

Selective catalytic reduction of NO_x by C₃H₆ in the presence of H₂ over Ag/Al₂O₃ was investigated using in situ DRIFTS and GC–MS measurements. The addition of H₂ promoted the partial oxidation of C₃H₆ to enolic species, the formation of –NCO and the reactions of enolic species and –NCO with NO_x on Ag/Al₂O₃ surface at low temperatures. Based on the results, we proposed reaction mechanism to explain the promotional effect of H₂ on the SCR of NO_x by C₃H₆ over Ag/Al₂O₃ catalyst.     

Selective oxidation of propylene to acrolein over supported V2O5/Nb2O5 catalysts: An in situ Raman, IR, TPSR and kinetic study

The vapor-phase selective oxidation of propylene (H₂CCHCH₃) to acrolein (H₂CCHCHO) was investigated over supported V₂O₅/Nb₂O₅ catalysts. The catalysts were synthesized by incipient wetness impregnation of V-isopropoxide/isopropanol solutions and calcination at 450 °C. The catalytic active vanadia component was shown by in situ Raman spectroscopy to be 100% dispersed as surface VO_x species on the Nb₂O₅ support in the sub-monolayer region (<8.4 V/nm²). Surface allyl species (H₂CCHCH_2*) were observed with in situ FT-IR to be the most abundant reaction intermediates. The acrolein formation kinetics and selectivity were strongly dependent on the surface VO_x coverage. Two surface VO_x sites were found to participate in the selective oxidation of propylene to acrolein. The reaction kinetics followed a Langmuir–Hinshelwood mechanism with first-order in propylene and half-order in O₂ partial pressures. C₃H₆-TPSR spectroscopy studies also revealed that the lattice oxygen from the catalyst was not capable of selectively oxidizing propylene to acrolein and that the presence of gas phase molecular O₂ was critical for maintaining the surface VO_x species in the fully oxidized state. The catalytic active site for this selective oxidation reaction involves the bridging VONb support bond.     

Catalytic reduction of SO2 over supported transition-metal oxide catalysts with C2H4 as a reducing agent

This work investigates performances of supported transition-metal oxide catalysts for the catalytic reduction of SO₂ with C₂H₄ as a reducing agent. Experimental results indicate that the active species, the support, the feed ratio of C₂H₄/SO₂, and pretreatment are all important factors affecting catalyst activity. Fe₂O₃/γ-Al₂O₃ was found to be the most active catalyst among six γ-Al₂O₃-supported metal oxide catalysts tested. With Fe₂O₃ as the active species, of the supports tested, CeO₂ is the most suitable one. Using this Fe₂O₃/CeO₂ catalyst, we found that the optimal Fe content is 10 wt.%, the optimal feed ratio of C₂H₄/SO₂ is 1:1, and the catalyst presulfidized by H₂+H₂S exhibits a higher performance than those pretreated with H₂ or He. Although the feed concentrations of C₂H₄:SO₂ being 3000:3000 ppm provide a higher conversion of SO₂, the sulfur yield decreases drastically at temperatures above 300 °C. With higher feed concentrations, maximum yield appears at higher temperatures. The C₂H₄ temperature-programmed desorption (C₂H₄-TPD) and SO₂-TPD desorption patterns illustrate that Fe₂O₃/CeO₂ can adsorb and desorb C₂H₄ and SO₂ more easily than can Fe₂O₃/γ-Al₂O₃. Moreover, the SO₂-TPD patterns further show that Fe₂O₃/γ-Al₂O₃ is more seriously inhibited by SO₂. These findings may properly explain why Fe₂O₃/CeO₂ has a higher activity for the reduction of SO₂.     

CO, H2 or C3H8 assisted catalytic combustion of methane over supported LaMnO3 monoliths

The effect of the addition of a second fuel such as CO, C₃H₈ or H₂ on the catalytic combustion of methane was investigated over ceramic monoliths coated with LaMnO₃/La-γAl₂O₃ catalyst. Results of autothermal ignition of different binary fuel mixtures characterised by the same overall heating value show that the presence of a more reactive compound reduces the minimum pre-heating temperature necessary to burn methane. The effect is more pronounced for the addition of CO and very similar for C₃H₈ and H₂. Order of reactivity of the different fuels established in isothermal activity measurements was: CO>H₂≥C₃H₈>CH₄. Under autothermal conditions, nearly complete methane conversion is obtained with catalyst temperatures around 800 °C mainly through heterogeneous reactions, with about 60–70 ppm of unburned CH₄ when pure methane or CO/CH₄ mixtures are used. For H₂/CH₄ and C₃H₈/CH₄ mixtures, emissions of unburned methane are lower, probably due to the proceeding of CH₄ homogeneous oxidation promoted by H and OH radicals generated by propane and hydrogen pyrolysis at such relatively high temperatures.

Finally, a steady state multiplicity is found by decreasing the pre-heating temperature from the ignited state. This occurrence can be successfully employed to pilot the catalytic ignition of methane at temperatures close to compressor discharge or easily achieved in regenerative burners.     

A comparative study of Ag/Al2O3 and Cu/Al2O3 catalysts for the selective catalytic reduction of NO by C3H6

The selective catalytic reduction (SCR) of NO by C₃H₆ in excess oxygen was evaluated and compared over Ag/Al₂O₃ and Cu/Al₂O₃ catalysts. Ag/Al₂O₃ showed a high activity for NO reduction. However, Cu/Al₂O₃ showed a high activity for C₃H₆ oxidation. The partial oxidation of C₃H₆ gave surface enolic species and acetate species on the Ag/Al₂O₃, but only an acetate species was clearly observed on the Cu/Al₂O₃. The enolic species is a more active intermediate towards NO + O₂ to yield—NCO species than the acetate species on the Ag/Al₂O₃ catalyst. The Ag and Cu metal loadings and phase changes on Al₂O₃ support can affect the activity and selectivity of Ag/Al₂O₃ and Cu/Al₂O₃ catalysts, but the formation of enolic species is the main reason why the activity of the Ag/Al₂O₃ catalyst for NO reduction is higher than that of the Cu/Al₂O₃ catalyst.     

Porous structures constructed from [SiMo12O40] and [SiW12O40] Keggin units

Three compounds, K₂(H₂O)₄H₂SiMo₁₂O₄₀ · 7H₂O (1), K₂Na₂(H₂O)₄SiW₁₂O₄₀ · 4H₂O (2), and Na₄(H₂O)₈SiMo₁₂O₄₀ · 6H₂O (3) have been synthesized and structurally characterized by single-crystal X-ray analysis, IR, and thermogravimetry. Compounds 1 and 2 both show the high symmetry trigonal space group P3₂21 and a novel 3D network structure. The Keggin anions [SiM₁₂O₄₀]⁴⁻(M = Mo, W) are linked by potassium or sodium cations to generate hexagon-shaped channels along the c-axis, in which water molecules are accommodated. Compound 3 is tetragonal, space group P4/mnc constructed from [SiMo₁₂O₄₀]⁴⁻ anions and Na ions.     

Selective catalytic reduction of NO by C3H8 over CoOx/Al2O3: An investigation of structure–activity relationships

A series of CoO_x/Al₂O₃ catalysts was prepared, characterized, and applied for the selective catalytic reduction (SCR) of NO by C₃H₈. The results of XRD, UV–vis, IR, Far-IR and ESR characterizations of the catalysts suggest that the predominant oxidation state of cobalt species is +2 for the catalysts with low cobalt loading (≤2 mol%) and for the catalysts with 4 mol% cobalt loading prepared by sol–gel and co-precipitation. Co₃O₄ crystallites or agglomerates are the predominant species in the catalysts with high cobalt loading prepared by incipient wetness impregnation and solid dispersion. An optimized CoO_x/Al₂O₃ catalyst shows high activity in SCR of NO by C₃H₈ (100% conversion of NO at 723 K, GHSV: 10,000 h⁻¹). The activity of the selective catalytic reduction of NO by C₃H₈ increases with the increase of cobalt–alumina interactions in the catalysts. The influences of cobalt loading and catalyst preparation method on the catalytic performance suggest that tiny CoAl₂O₄ crystallites highly dispersed on alumina are responsible for the efficient catalytic reduction of NO, whereas Co₃O₄ crystallites catalyze the combustion of C₃H₈ only.     

Water vapor sensitivity of nanosized La(Co, Mn, Fe)1−x(Cu, Pd)xO3 perovskites during NO reduction by C3H6 in the presence of oxygen

A series of La(Co, Mn, Fe)_1−x(Cu, Pd)_xO₃ perovskites having high specific surface areas and nanosized crystal domains was prepared by reactive grinding. The solids were characterized by N₂ adsorption, X-ray diffraction (XRD), scanning electron microscopy (SEM), temperature programmed desorption (TPD) of O₂, NO + O₂, C₃H₆, in the absence or presence of 5% H₂O, Fourier transform infrared (FTIR) spectroscopy, as well as activity tests towards NO reduction by propene under the conditions of 3000 ppm NO, 3000 ppm C₃H₆, 1% O₂, 0 or 10% H₂O, and 50,000 h⁻¹ space velocity. The objective was to investigate the influence of H₂O addition on catalytic behavior. A good performance (100% NO conversion, 77% N₂ yield, and 90% C₃H₆ conversion) was achieved at 600 °C over LaFe_0.8Cu_0.2O₃ under a dry feed stream. With the exposure of LaFe_0.8Cu_0.2O₃ to a humid atmosphere containing 10% water vapor, the catalytic activity was slightly decreased yielding 91% NO conversion, 51% N₂ yield, and 86% C₃H₆ conversion. A competitive adsorption between H₂O vapor with O₂ and NO molecules at anion vacancies over LaFe_0.8Cu_0.2O₃ was found by means of TPD studies here. A deactivation mechanism was therefore proposed involving the occupation of available active sites by water vapor, resulting in an inhibition of catalytic activity in C₃H₆ + NO + O₂ reaction. This H₂O deactivation was also verified to be strictly reversible by removing steam from the feed.     

Lean reduction of NO by C3H6 over Ag/alumina derived from Al2O3, AlOOH and Al(OH)3

The effectiveness of Ag/Al₂O₃ catalyst depends greatly on the alumina source used for preparation. A series of alumina-supported catalysts derived from AlOOH, Al₂O₃, and Al(OH)₃ was studied by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), ultraviolet–visible (UV–vis) spectroscopy, diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy, O₂, NO + O₂-temperature programmed desorption (TPD), H₂-temperature programmed reduction (TPR), thermal gravimetric analysis (TGA) and activity test, with a focus on the correlation between their redox properties and catalytic behavior towards C₃H₆-selective catalytic reduction (SCR) of NO reaction. The best SCR activity along with a moderated C₃H₆ conversion was achieved over Ag/Al₂O₃ (I) employing AlOOH source. The high density of Ag–O–Al species in Ag/Al₂O₃ (I) is deemed to be crucial for NO selective reduction into N₂. By contrast, a high C₃H₆ conversion simultaneously with a moderate N₂ yield was observed over Ag/Al₂O₃ (II) prepared from a γ-Al₂O₃ source. The larger particles of Ag_mO (m > 2) crystallites were believed to facilitate the propene oxidation therefore leading to a scarcity of reductant for SCR of NO. An amorphous Ag/Al₂O₃ (III) was obtained via employing a Al(OH)₃ source and 500 °C calcination exhibiting a poor SCR performance similar to that for Ag-free Al₂O₃ (I). A subsequent calcination of Ag/Al₂O₃ (III) at 800 °C led to the generation of Ag/Al₂O₃ (IV) catalyst yielding a significant enhancement in both N₂ yield and C₃H₆ conversion, which was attributed to the appearance of γ-phase structure and an increase in surface area. Further thermo treatment at 950 °C for the preparation of Ag/Al₂O₃ (V) accelerated the sintering of Ag clusters resulting in a severe unselective combustion, which competes with SCR of NO reaction. In view of the transient studies, the redox properties of the prepared catalysts were investigated showing an oxidation capability of Ag/Al₂O₃ (II and V) > Ag/Al₂O₃ (IV) > Ag/Al₂O₃ (I) > Ag/Al₂O₃ (III) and Al₂O₃ (I). The formation of nitrate species is an important step for the deNO_x process, which can be promoted by increasing O₂ feed concentration as evidenced by NO + O₂-TPD study for Ag/Al₂O₃ (I), achieving a better catalytic performance.     

Surface properties and reactivity of Cu/γ-Al2O3 catalysts for NO reduction by C3H6: Influences of calcination temperatures and additives

The influences of calcination temperatures and additives for 10 wt.% Cu/γ-Al₂O₃ catalysts on the surface properties and reactivity for NO reduction by C₃H₆ in the presence of excess oxygen were investigated. The results of XRD and XPS show that the 10 wt.% Cu/γ-Al₂O₃ catalysts calcined below 973 K possess highly dispersed surface and bulk CuO phases. The 10 wt.% Cu/γ-Al₂O₃ and 10 wt.% Mn–10 wt.% Cu/γ-Al₂O₃ catalysts calcined at 1073 K possess a CuAl₂O₄ phase with a spinel-type structure. In addition, the 10 wt.% La–10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K possesses a bulk CuO phase. The result of NO reduction by C₃H₆ shows that the CuAl₂O₄ is a more active phase than the highly dispersed and bulk CuO phase. However, the 10 wt.% Mn–10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K possesses significantly lower reactivity for NO reduction than the 10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K, although these catalysts possess the same CuAl₂O₄ phase. The low reactivity for NO reduction for 10 wt.% Mn–10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K is attributed to the formation of less active CuAl₂O₄ phase with high aggregation and preferential promotion of C₃H₆ combustion to CO_x by MnO₂. The engine dynamometer test for NO reduction shows that the C₃H₆ is a more effective reducing agent for NO reduction than the C₂H₅OH. The maximum reactivity for NO reduction by C₃H₆ is reached when the NO/C₃H₆ ratio is one.     

Combined effect of H2O and SO2 on V2O5/AC catalysts for NO reduction with ammonia at lower temperatures

Combined effect of H₂O and SO₂ on V₂O₅/AC the activity of catalyst for selective catalytic reduction (SCR) of NO with NH₃ at lower temperatures was studied. In the absence of SO₂, H₂O inhibits the catalytic activity, which may be attributed to competitive adsorption of H₂O and reactants (NO and/or NH₃). Although SO₂ promotes the SCR activity of the V₂O₅/AC catalyst in the absence of H₂O, it speeds the deactivation of the catalyst in the presence of H₂O. The dual effect of SO₂ is attributed to the SO₄²⁻ formed on the catalyst surface, which stays as ammonium-sulfate salts on the catalyst surface. In the absence of H₂O, a small amount of ammonium-sulfate salts deposits on the surface of the catalyst, which promote the SCR activity; in the presence of H₂O, however, the deposition rate of ammonium-sulfate salts is much greater, which results in blocking of the catalyst pores and deactivates the catalyst. Decreasing V₂O₅ loading decreases the deactivation rate of the catalyst. The catalyst can be used stably at a space velocity of 9000 h⁻¹ and temperature of 250 °C.     

Kinetics of propylene epoxidation using H2 and O2 over a gold/mesoporous titanosilicate catalyst

The oxidation of propylene to propylene oxide (PO) with hydrogen–oxygen mixtures was studied on gold supported on the mesoporous titanium silicate, Ti-TUD. The catalyst gave stable activity at low conversions of propylene (<6%) and high selectivity to PO (>95%). Kinetic data were fit to a power-rate law and gave the following expression: r_PO = k(H₂)^0.54(O₂)^0.24(C₃H₆)^0.36. The fractional orders in hydrogen, oxygen, and propylene indicated that these reactants interacted with the catalyst to form species that led to the final PO product. The catalyst likely operated by the commonly accepted mechanism of hydrogen peroxide production on gold sites, and epoxidation on titanium centers. Carbon dioxide was formed primarily from further oxidation of PO rather than the oxidation of propylene, while water was produced from the reaction of hydrogen and oxygen.     

Enhanced activity of metal oxide-doped Ga2O3–Al2O3 for NO reduction by propene

Effect of additives, In₂O₃, SnO₂, CoO, CuO and Ag, on the catalytic performance of Ga₂O₃–Al₂O₃ prepared by sol–gel method for the selective reduction of NO with propene in the presence of oxygen was studied. As for the reaction in the absence of H₂O, CoO, CuO and Ag showed good additive effect. When H₂O was added to the reaction gas, the activity of CoO-, CuO- and Ag-doped Ga₂O₃–Al₂O₃ was depressed considerably, while an intensifying effect of H₂O was observed for In₂O₃- and SnO₂-doped Ga₂O₃–Al₂O₃. Of several metal oxide additives, In₂O₃-doped Ga₂O₃–Al₂O₃ showed the highest activity for NO reduction by propene in the presence of H₂O. Kinetic studies on NO reduction over In₂O₃–Ga₂O₃–Al₂O₃ revealed that the rate-determining step in the absence of H₂O is the reaction of NO₂ formed on Ga₂O₃–Al₂O₃ with C₃H₆-derived species, whereas that in the presence of H₂O is the formation of C₃H₆-derived species. We presumed the reason for the promotional effect of H₂O as follows: the rate for the formation of C₃H₆-derived species in the presence of H₂O is sufficiently fast compared with that for the reaction of NO₂ with C₃H₆-derived species in the absence of H₂O. Although the retarding effect of SO₂ on the activity was observed for all of the catalysts, SnO₂–Ga₂O₃–Al₂O₃ showed still relatively high activity in the lower temperature region.     

Deactivation and regeneration of TS-1/SiO2 catalyst for epoxidation of propylene with hydrogen peroxide in a fixed-bed reactor

TS-1/SiO₂ catalyst for the epoxidation of propylene with hydrogen peroxide in a fixed-bed reactor has been investigated. The catalyst activity decreases gradually with the online reaction time, but the selectivity of propylene epoxide is kept at about 93%. The fresh, deactivated and regenerated catalysts were characterized with X-ray diffraction, Fourier transform infrared spectroscopy, ultra-violet-visible diffuse reflectance, Brunner-Emmett-Teller method and thermogravimetric analysis, and the deactivated catalyst was regenerated with H₂O₂/methanol solution. Compared with the fresh catalyst, both the framework structure and the content of titanium in the framework of the deactivated and regenerated TS-1/SiO₂ catalysts were not changed. The major reason of the catalyst deactivation was the blockage of the channels of the catalyst by bulky organic by-products, which covered the active centers of titanium in TS-1. The deposited materials on the deactivated TS-1/SiO₂ catalyst could be removed by treatment with hydrogen peroxide/methanol solution or pure methanol; the higher the treatment temperature and the higher the concentration of H₂O₂ in methanol, the higher the extent of the regeneration. The regeneration treatment did not influence the product selectivity in the propylene epoxidation.     

WO_3负载量对V_2O_5/WO_3-TiO_2催化剂脱硝性能的影响

采用V_2O_5/WO_3-TiO_2作为脱硝催化剂,考察活性组分V_2O_5和助剂WO_3负载量对催化剂脱硝活性和抗硫抗水性能的影响。结果表明,3%V_2O_5/x WO_3-TiO_2催化剂(x=3%、4%、5%、6%、7%、8%、9%、10%)上NOx转化率随着WO_3负载量增加而升高,催化剂反应温度窗口不断拓宽。单独通水蒸汽及同时通SO2和水蒸汽对催化剂的毒害作用均较强,表明H2O和NH3的竞争吸附是催化剂抗硫抗水性能较差的重要原因。SO_2与H_2O和NH_3反应生成亚硫酸铵盐和硫酸铵盐,导致催化剂孔隙堵塞,催化活性降低。     

[C16H33N(CH3)3]3[PO4(WO3)4]催化脂肪酸甲酯环氧化性能

在无酸、无溶剂条件下,以[C₁₆H₃₃N(CH₃)₃]₃[PO₄(WO₃)₄]为反应控制相转移催化剂,研究各因素对脂肪酸甲酯(FAME)环氧化反应的影响。结果表明,水相pH对环氧化反应的影响最大,反应适宜pH为4;适宜反应条件为过氧化氢与脂肪酸甲酯中双键摩尔比为1.05:1,反应温度50～60℃,反应时间5 h。在此反应条件下催化剂循环5次不失活,产品环氧值大于4.0%,碘值小于5 g I·(100 g)^-1。并通过元素分析与红外光谱,研究了催化剂在反应过程中的变化,认为磷钨杂多阴离子的分解是导致催化剂失活的关键原因。     

Promoting effect of calcium on reduction of NO by C3H6 over V2O5/ZrO2 catalysts

The reduction of nitrogen monoxide by propene on V₂O₅/ZrO₂ doped with or without calcium has been studied by FTIR spectroscopy as well as by analysis of the reaction products. Considerable promoting effect of calcium doping on the reduction of nitrogen monoxide by propene was observed on the V₂O₅/ZrO₂ catalysts. For the reaction of a mixture of NO+C₃H₆, carbonyl and carboxylate species were observed above 373 K, although nitrate species formed at room temperature on V₂O₅/ZrO₂ doped with calcium. No bands due to a compound including both carbon and nitrogen atoms were observed. Thus, the redox mechanism, i.e. propene reduces the catalyst and nitrogen monoxide oxidizes the catalyst, is confirmed on V₂O₅/ZrO₂ catalysts doped with or without calcium. The analysis of the V=O band in the region of 1100–900 cm⁻¹ indicates that this promotion is mainly due to new V=O species formed by the addition of calcium onto the catalyst. This species is easily reproduced in comparison with the other V=O species on the surface in the reoxidation process of the catalyst.     

Selective catalytic reduction of NO by C2H2 over MoO3/HZSM-5

Molybdenum impregnated HZSM-5 zeolite catalysts with MoO₃ loading from 1 to 8 wt.% were studied in detail for the selective catalytic reduction (C₂H₂-SCR) of NO by acetylene. A 83.9% of NO could be removed by the reductant at 350 °C under 1600 ppm of NO, 800 ppm of C₂H₂ and 9.95% of O₂ in He over 2%MoO₃/HZSM-5 catalyst with a specific activity of in NO elimination and the competitiveness factor (c.f.) of 33.6% for the reductant. The NO elimination level and the c.f. value were ca. 3–4 times as high as those using methane or propene as reductant over the catalyst in the same reaction condition. About same reaction rate was estimated in NO oxidation as that in the NO reduction over each xMoO₃/HZSM-5 (x = 0–8%) catalyst, which confirms that NO₂ is a crucial intermediate for the aimed reaction over the catalysts. Appropriate amount of Mo incorporation to HZSM-5 considerably enhanced the title reaction, both by accelerating the intermediate formation and by strengthening the adsorption NO_x on the catalyst surface under the reaction conditions. Rather lower adsorption tendency of acetylene compared with propene on the catalysts explains the catalyst's steady performance in the C₂H₂-SCR of NO and rapid deactivation in the C₃H₆-SCR of NO.     

Pt/TiO_2催化二甲醚部分氧化重整制氢

二甲醚是一种理想的氢载体,可用于解决氢的储存和运输。以Pt/TiO_2为部分氧化催化剂,结合Ni/Al_2O_3重整催化剂,考察钛前驱体和焙烧温度对二甲醚部分氧化重整制氢反应的影响。结果表明,以Ti(C4H9O)4为原料制备的TiO_2为金红石相,Ti(SO4)2或Ti O(OH)2为原料制备的TiO_2为锐钛矿相;以Ti(C4H9O)4为原料制备的Pt/TiO_2-E催化剂催化性能略好,转化率接近100%,H2收率约90%,表明金红石相TiO_2负载的Pt催化剂略佳;以Ti(SO4)2为原料制备的Pt/TiO_2-S催化剂500℃焙烧可获得金红石相TiO_2。与Pt/Al_2O_3催化剂相比,Pt/TiO_2催化剂具有更好的催化性能,H2收率超过90%,而Pt/Al_2O_3催化剂H2收率约80%。     

PtSn负载量对PtSn/Al2O3催化剂上丙烷脱氢性能的影响

由丙烷直接催化脱氢制取丙烯已经成为增产丙烯的重要手段之一。以水热法制备Al_2O_3载体,采用等体积浸渍法制备不同PtSn负载量的PtSn/Al_2O_3催化剂。通过XRD、N2-吸附、拉曼光谱和H2-TPR等对其进行表征,并考察不同PtSn负载量对催化剂催化丙烷脱氢性能的影响。结果表明,在制备的催化剂中,Pt1.5Sn3/Al_2O_3具有最高的催化丙烷脱氢活性和稳定性,丙烷初始转化率高达55.6%,丙烯选择性98.1%。反应330 min后,丙烷转化率仅降约10%,选择性保持不变。