Role of cobalt on γ-Al2O3 based NO x storage catalyst

Co/Pt/Ba/γ-Al₂O₃, Co/Ba/γ-Al₂O₃, Pt/Ba/γ-Al₂O₃, Co/Pt/γ-Al₂O₃, Ba/γ-Al₂O₃, Pt/γ-Al₂O₃, and Co/γ-Al₂O₃ type catalysts were prepared by a conventional impregnation method, and their NO _x storage capacities were evaluated by colorimetric assay. Co-containing catalysts had a higher NO _x storage capacity than that of Co-free counterparts. The role of each component, especially Co, for the catalysts prepared was investigated by using in-situ FTIR. The high NO _x storage for Co-containing catalysts including Co/Ba/γ-Al₂O₃ and Co/Pt/Ba/γ-Al₂O₃ is mainly due to the formation of Co₃O₄ on the catalyst surface identified by XAFS.     

Deactivation and coke formation on palladium and platinum catalysts in vegetable oil hydrogenation

Deactivation of palladium and platinum catalysts due to coke formation was studied during hydrogenation of methyl esters of sunflower oil. The supported metal catalysts were prepared by impregnating γ-alumina with either palladium or platinum salts, and by impregnating α-alumina with palladium salt. The catalysts were reused for several batch experiments. The Pd/γ-Al₂O₃ catalyst lost more than 50% of its initial activity after four batch experiments, while the other catalysts did not deactivate. Samples of used catalysts were cleaned from remaining oil by repeated extractions with methanol, and the amount of coke formed on the catalysts was studied by temperature-programmed oxidation. The deactivation of the catalyst is a function of both the metal and the support. The amount of coke increased on the Pd/γ-Al₂O₃ catalyst with repeated use, but the amount of coke remained approximately constant for the Pt/γ-Al₂O₃ catalyst. Virtually no coke was detected on the Pd/α-Al₂O₃ catalyst. The formation of coke on Pd/α-Al₂O₃ may be slower than on the Pd/γ-Al₂O₃ owing to the carrier’s smaller surface area and less acidic character. The absence of deactivation for the Pt/γ-Al₂O₃ catalyst may be explained by slower formation of coke precursors on platinum compared to palladium.     

Pt–Ni/γ-Al2O3 catalyst for the preferential CO oxidation in the hydrogen stream

The preferential CO oxidation (PROX) in the presence of excess hydrogen was studied over Pt–Ni/γ-Al₂O₃. CO chemisorption, X-ray diffraction, transmission electron microscopy, energy dispersive X-ray spectroscopy and temperature-programmed reduction were conducted to characterize active catalysts. The co-impregnated Pt–Ni/γ-Al₂O₃ was superior to Pt/Ni/γ-Al₂O₃ and Ni/Pt/γ-Al₂O₃ prepared by a sequential impregnation of each component on alumina support. The PROX activity was affected by the reductive pretreatment condition. The pre-reduction was essential for the low-temperature PROX activity. As the reduction temperature increased above 423 K, the CO₂ selectivity decreased and the atomic percent of Ni in the bimetallic phase of Pt–Ni increased. This catalyst exhibited the high CO conversion even in the presence of 2% H₂O and 20% CO₂ over a wide reaction temperature. The bimetallic phase of Pt–Ni seems to give rise to high catalytic activity for the PROX in H₂-rich stream.     

Methane conversion over nanostructured Pt/γAl2O3 catalysts in dielectric-barrier discharge

Spherical nanostructured γ-Al₂O₃ granules were prepared by combining the modified Yoldas process and oil-drop method, followed by the Pt impregnation inside mesopores of the granules by incipient wetness method. Prepared Pt/γ-Al₂O₃ catalysts were reduced by novel method using plasma, which was named plasma assisted reduction (PAR), and then used for methane conversion in dielectric-barrier discharge (DBD). The effect of Pt loading, calcination temperature on methane conversion, and selectivities and yields of products were investigated. Prepared Pt/γ-Al₂O₃ catalysts were successfully reduced by PAR. The main products of methane conversion were the light alkanes such as C₂H₆, C₃H₈ and C₄H₁₀ when the catalytic plasma reaction was carried out with Pt/γ-Al₂O₃ catalyst. Methane conversion was in the range of 38–40% depending on Pt loading and calcination temperature. The highest yield of C₂H₆ was 12.7% with 1 wt% Pt/γ-Al₂O₃ catalysts after calcinations at 500 ‡C.     

CO2 effect on activity and stability of NOx storage reduction catalysts

A catalyst for NO_x storage/reduction was prepared to improve the activity of Ba–Pt/γ-Al₂O₃ by replacing Ba with a mixture of Ba and Mg. The catalyst was prepared by impregnating Pt and then co-impregnating Ba and Mg (Mg:Ba molar ratio = 1) on commercial γ-Al₂O₃. The tests have been carried out in the presence of CO₂ at temperatures between 200 and 400 °C in order to understand the role of both the feed and various alkaline-earth metals. The storage capacity of the two catalysts was different like the mechanism in the reduction process.     

Characterization of nickel sulfate supported on γ-Al2O3 and its relationship to acidic properties

A series of NiSO₄/γ-Al₂O₃ catalysts were prepared by the impregnation method using an aqueous solution of nickel sulfate. The high catalytic activity of NiSO₄/γ-Al₂O₃ for both 2-propanol dehydration and cumene dealkylation was related to the increase of acidity and acid strength due to the addition of NiSO₄. 20(wt%)-NiSO₄/g-Al₂O₃ calcined at 600 °C exhibited maximum catalytic activities for 2-propanol dehydration and cumene dealkylation. The catalytic activities for both reactions were correlated with the acidity of catalysts measured by the ammonia chemisorption method. This paper is dedicated to Professor Wha Young Lee on the occasion of his retirement from Seoul National University.     

Operando X-ray Absorption Spectroscopy Study of Pt/γ-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> During the Total Oxidation of C<Subscript>3</Subscript>H<Subscript>6</Subscript>

Operando X-ray absorption fine structure (XAFS) investigations were performed on Pt/γ-Al₂O₃ during the total oxidation of C₃H₆ in reducing and oxidizing atmospheres. Study of the Pt valance state and catalytic conversion behavior as a function of temperature revealed that both the creation of metallic Pt sites and the activation of adsorbed species on Pt are important for the functioning of the catalytic reaction at low temperature.     

Hydrodesulfurization of dibenzothiophene over supported and unsupported molybdenum carbide catalysts

A series of γ-Al₂O₃ supported molybdenum carbides [carbided Mo/γ-Al₂O₃ (MCS), Co-Mo/γ-Al₂O₃ (CMCS), and Ni-Mo/γ-Al₂O₃ (NMCS)] and unsupported molybdenum carbide (MCUS) were prepared by the temperature-programmed carburization of their corresponding molybdenum nitrides with 20 % CH₄/H₂. XRD and SEM studies show that unsupported molybdenum carbide catalyst possesses a typical crystalline Mo₂C (FCC structure), while supported molybdenum carbide catalysts possess highly dispersed surface molybdenum carbide species on an alumina oxide support. The results of dibenzothiophene (DBT) hydrodesulfurization over molybdenum carbide catalysts show that the reactivity is strongly dependent on the type of catalyst. Supported molybdenum carbide catalysts possess a higher reactivity than the unsupported molybdenum carbide catalyst. In addition, Co or Ni promoted, supported molybdenum carbide catalyst possesses a higher reactivity than the unpromoted, supported molybdenum carbide catalyst. The reactivity, which is also dependent on the reaction conditions, increases with increasing reaction temperature and pressure and contact time. The CO uptakes of the molybdenum carbide catalysts correlate well with overall activity (total rate) for DBT hydrodesulfurization. The major reaction product is biphenyl, with cyclohexylbenzene next in abundance regardless of the type of catalysts and reaction conditions. It was also found that the molybdenum carbide catalysts exhibit stable initial reactivity due to the stable and weak acidic characteristics of these catalysts.     

Selective CO oxidation in the presence of hydrogen over supported Pt catalysts promoted with transition metals

Selective CO oxidation in the presence of excess hydrogen was studied over supported Pt catalysts promoted with various transition metal compounds such as Cr, Mn, Fe, Co, Ni, Cu, Zn, and Zr. CO chemisorption, XRD, TPR, and TPO were conducted to characterize active catalysts. Among them, Pt-Ni/γ-Al₂O₃ showed high CO conversions over wide reaction temperatures. For supported Pt-Ni catalysts, Alumina was superior to TiO₂ and ZrO₂ as a support. The catalytic activity at low temperatures increased with increasing the molar ratio of Ni/Pt. This accompanied the TPR peak shift to lower temperatures. The optimum molar ratio between Ni and Pt was determined to be 5. This Pt-Ni/γ A1₂O₃ showed no decrease in CO conversion and CO₂ selectivity for the selective CO oxidation in the presence of 2 vol% H₂O and 20 vol% CO₂. The bimetallic phase of Pt-Ni seems to give rise to stable activity with high CO₂ selectivity in selective oxidation of CO in H₂-rich stream.     

Gas phase hydrodechlorination of chlorinated aromatic compounds on nickel catalysts

Supported Ni/-Al₂O₃ catalysts were studied in the gas phase hydrodechlorination of substituted chlorobenzenes. The catalytic properties of the catalysts were shown to be determined by the metal nickel. A correlation between the rate of the gas phase hydrodechlorination of substituted chlorobenzene and donor-acceptor properties of substituents was established. The electron-donor substituents increase and the electron-acceptor ones decrease their reactivity. The correlation analysis of data treated via the Hammett equation shows that hydrodechlorination on Ni/-Al₂O₃ catalysts is a reaction of electrophilic type.     

Correlating Low-temperature Hydrogenation Activity of Co/Pt(111) Bimetallic Surfaces to Supported Co/Pt/γ-Al2O3 Catalysts

The low-temperature self-hydrogenation (disproportionation) of cyclohexene was used as a probe reaction to correlate the reactivity of Co/Pt(111) bimetallic surfaces with supported Co/Pt/γ-Al₂O₃ catalysts. Temperature-programmed desorption (TPD) experiments show that cyclohexene undergoes self-hydrogenation on the ~1 ML Co/Pt(111) surface at ~219 K, which does not occur on either pure Pt(111) or a thick Co film on Pt(111). Supported catalysts with a 1:1 atomic ratio of Co:Pt were synthesized on a high surface area γ-Al₂O₃ to verify the bimetallic effect on the self-hydrogenation of cyclohexene. EXAFS experiments confirmed the presence of Co–Pt bonds in the catalyst. Using FTIR in a batch reactor configuration, the bimetallic catalyst showed a higher activity toward the self-hydrogenation of cyclohexene at room temperature than either Pt/γ-Al₂O₃ or Co/γ-Al₂O₃ catalysts. The comparison of Co/Pt(111) and Co/Pt/γ-Al₂O₃ provided an excellent example of correlating the self-hydrogenation activity of cyclohexene on bimetallic model surfaces and supported catalysts.     

Partial oxidation of methane over nickel catalysts supported on various aluminas

Partial oxidation of methane (POM) was systematically investigated in a fixed bed reactor over 12 wt% Ni catalysts supported on α-A1₂O₃, γ-A1₂O₃ and θ-A1₂O₃ which were prepared at different conditions. Results indicate that the catalytic activity toward POM strongly depends on the BET surface area of the support. All the Ni/ θ-Al₂O₃ catalysts showed high activity toward POM due to the less formation of inactive NiAl₂O₄ species, the existence of NiO, species and stable θ-Al₂O₃ phase. Although Ni/γ-Al₂O₃ showed the highest activity toward POM, long-time stability cannot be expected as a result of the deterioration of the support at higher temperature, which is revealed from BET results. From the reaction and characterization results, it is inferred that the optimal conditions for the preparation of θ-Al₂O₃ are 1,173 K and 12 h.     

Low Temperature and H2 Selective Catalysts for Ethanol Steam Reforming

Supported Rh catalysts have been developed for selective H₂ production at low temperatures. Ethanol dehydration is favorable over either acidic or basic supports such as γ-Al₂O₃ and MgAl₂O₄, while ethanol dehydrogenation is more favorable over neutral supports. CeO₂–ZrO₂-supported Rh catalysts were found to be especially effective for hydrogen production. We focused on a support prepared by a co-precipitation method having composition Ce_0.8Zr_0.2O₂. A 2%Rh/Ce_0.8Zr_0.2O₂ catalyst, prepared via impregnation without pre-calcination of support, exhibited the highest H₂ yield at 450 °C among various supported Rh catalysts evaluated in this study. This may be due to both the strong interaction between Rh and Ce_0.8Zr_0.2O₂ and the high oxygen transfer rate favoring reforming of acetaldehyde instead of methane production.     

Roles of Pt and alumina during the combustion of coke deposits on propane dehydrogenation catalysts

Temperature programmed oxidation of coke deposited on Pt based propane dehydrogenation catalysts reveals that the deposited coke can be categorised into three groups according to their burning temperatures. When coke was separated from the catalyst, however, only one TPO peak could be observed. Experimental results suggest that γ-Al₂O₃ enhances the coke burning process by increasing coke surface area contacts to oxygen. Pt may also act as a catalyst for the coke combustion reaction. Experiments also show that changing dehydrogenation reaction temperature, variation of H₂/HC ratios, addition of only Sn or Sn and an alkali metal (Li, Na and K) can significantly affect the amount of each coke formed. Sample weight used in the temperature programmed oxidation (TPO) experiment also affects the resolution of TPO spectrum.     

Reduction of NO by H2 on PdO-MoO3/γ-Al2O3 of low molybdena loading

The catalytic activity and selectivity of three PdO-MoO₃/-Al₂O₃ catalysts containing about 2% Pd and 2% Mo were studied for the reduction of NO by h₂ in the presence of varying amounts of oxygen at temperatures from 50 to 550 °C. The results are compared with those for PdO/-Al₂O₃, PdO-MoO₃/-Al₂O₃ containing 2% Pd and 20% Mo, and a commercial Pt-Rh catalyst. In the absence of oxygen, the conversion of NO to N₂ and N₂O is higher on the three catalysts than it is on PdO/-Al₂O₃ at 500 and 550 °C. In the presence of oxygen, the yields of N₂ and N₂O are generally lower on two of the PdO-MoO₃/-Al₂O₃ catalysts than on PdO/-Al₂O₃.     

Role of Support in Lean DeNOx Catalysis

FTIR and pulse thermal analysis were applied to investigate catalysts containing Pt (1 wt%)/Ba (17 wt%) supported on -Al₂O₃, SiO₂ and ZrO₂. The aim was to learn how the support material affects the thermal stability of barium carbonate and its activity in the reaction to bulk Ba(NO₃)₂. The lower thermal stability of BaCO₃ in alumina supported samples was found to influence the formation of barium nitrate during the NO _x storage process. Quantification of Ba(NO₃)₂ formed during NO _x storage indicated that for alumina supported catalysts only ca. 30% of barium present in the sample is involved in the storage process. The low thermal stability found for alumina supported barium nitrite excludes its role in the formation of barium nitrate during interaction of NO _x with the catalyst at 300 °C. The studies indicate that -Al₂O₃ plays a major role in influencing the thermal stability of BaCO₃ and Ba(NO₃)₂. This finding seems to be relevant for the higher activity of -Al₂O₃-supported catalysts in NO _x storage reduction reactions.     

Premodification of Pt/γAl2O3 with Cinchonidine for the Enantioselective Hydrogenation of Ethyl Pyruvate: Effect of Premodification Conditions on Reaction Rate and Enantioselection

The premodification of a 5 wt% Pt/-Al₂O₃ catalyst with cinchonidine (0.01 and 0.2 g g^-1 _catalyst) is described and discussed. Premodification is carried out by treating the catalyst with a solution of cinchonidine followed by solvent removal. Catalysts premodified in this way give the same ee and initial rate of reaction for the enantioselective hydrogenation of ethyl pyruvate as those using the standard in situ modification procedure. Investigations of different solvents for premodification and reaction (dichloromethane, ethanol) show that it is the solvent used for the reaction that controls the observed enantioselection. Premodified catalysts also display the initial transient behavior typically observed with in situ modified catalysts in which the ee increases with conversion in the early part of the reaction. Premodified catalysts show an enhanced rate of reaction when ethanol is used as the reaction solvent compared with in situ modified catalysts under the same conditions. Premodification using aerobic conditions gives the best results and premodified catalysts can be stored prior to use for up to a week without loss of catalytic performance.     

Hydrogen–deuterium isotope effects in the reactions of chlorobenzene and benzene on a Pt/γ-Al2O3 catalyst

The kinetic isotope effect for combustion of a C₆H₅Cl/C₆D₅Cl mixture on Pt/-Al₂O₃ was found to be close to unity between 520 and 580 K. However, in the presence of an excess of heptane, an isotope effect of 1.5 was found between 460 and 490 K. For the combustion of a C₆H₆/C₆D₆ mixture the k_H/k_D value was around 2 between 404 and 439 K. The results show that in the combustion of chlorobenzene per se, C–H bond activation is not a rate-determining step. On Pt sites, C–Cl bond scission probably occurs already at low temperatures. The chlorine and the phenyl group cannot easily react further. Chlorine on the surface is active in chlorination, which is shown by the formation of C₆D₅Cl in an experiment with C₆H₅Cl and C₆D₆. Only at a certain temperature is the chlorine removed, partly as polychlorinated benzenes. The removal of chlorine from the catalyst allows oxygen to take part in the reaction, which determines the rate of the combustion of chlorobenzene. When heptane is present, Cl is removed from the surface and C–H bond scission can become rate determining, as is also the case in the combustion of C₆H₆/C₆D₆. Upon (partial) combustion of C₆H₅Cl/C₆D₅Cl and C₆H₆/C₆D₆ mixtures on a Pt/-Al₂O₃ catalyst, hydrogen–deuterium exchange occurs on the -Al₂O₃ support.     

A planar catalytic combustion sensor using nano-crystalline F-doped SnO2 as a supporting material for hydrogen detection

A planar catlytic combustion gas sensor based on Pd/Pt catalyst supported on F-doped SnO₂ nano-crystalline materials has been designed and fabricated for hydrogen detection. The sensor consists of platinum heaters on an alumina plate coated with a catalytic layer and compensating layer. This sensor exhibited better performance than that of the sensors employing sensing material of Pd/Pt catalyst on γ-Al₂O₃ and of Pd/Pt catalyst on nano-crystalline SnO₂. The detection limit of the sensor at 370 °C is in the concentration range of 0.5–5% (v/v), with an excellent linearity of signal voltage to the hydrogen gas concentration.     

Activity of vanadium magnesium oxide supported catalysts in the dehydrogenation of isobutane

The activity of the vanadium magnesium binary oxides supported on C_act, SiO₂, γ-Al₂O₃ and ZnO in the dehydrogenation of isobutane to isobutene under the carbon dioxide or inert gas atmosphere was investigated. The highest isobutene yield (34.8%) was obtained over active carbon supported catalyst. The role of carbon dioxide in the dehydrogenation process was determined on the basis of additional tests: the RWGS reaction, gasification of coke and regeneration of partially reduced catalysts. The temperature-programmed techniques (TPR-H₂, TPD-NH₃ and TPD-CO₂) were used to characterize the catalysts.