Long chain branched poly(butylene succinate‐co‐terephthalate) copolyesters using pentaerythritol as branching agent: Synthesis,thermo‐mechanical,and rheological properties

Incorporating long chain branching (LCB) structure into biodegradable copolyesters can effectively improve their melt strength and film blowing processability. However, branching also results in deterioration of crystallizability which is also important for copolyester properties and processing. In this study, pentaerythritol (PER) was used as branching agent (BA) instead of previous used in‐situ BA, diglycidyl 1,2,3,6‐tetrahydrophthalate (DGT), to synthesize LCB poly(butylene succinate‐co‐terephthalate) (PBST) copolyesters. The chain structure was characterized and the effects of branching on thermal transition, mechanical, and rheological properties were investigated. Similar to DGT, copolymerizing small amount of PER (0.1–0.4 mol %) generates LCB structure and, therefore, improves the melt elasticity or strength and tensile modulus but reduces the elongation at break. Differing from DGT, PER showed higher branching efficiency, and PER‐branched PBSTs exhibited unchanged or even improved crystallization ability compared with linear PBST. The improved melt strength coupled with good crystallizability will endow PER‐branched PBSTs with better film blowing processability. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44544.     

Preparation and characterization of the ethylene‐vinyl acetate copolymer partially hydrolyzed assisted by microwave radiation

Ethylene‐vinyl acetate copolymer (EVA) was modified by hydrolysis using dielectric heating. The modified EVA was characterized by Fourier transform infrared spectroscopy, differential scanning calorimetry, thermogravimetric analysis (TG), ¹H Nuclear magnetic resonance (NMR), gel permeation chromatography, and small‐angle X‐ray scattering. The results showed that the EVA was hydrolyzed with degree between 36.1 and 42.6% according to ¹H NMR and TG results. The relative reaction rate for the sample prepared in the oil bath was ～9%/h, while in the dielectric was ～150%/h for 15 min. This significant improvement was due to the specific effect of microwave‐assisted reactions through dipole rotation and ionic polarization contributions. The hydrolysis reaction promoted a reduction of the pendent group size of EVA backbone. This change directly contributed to increasing melt temperature, crystallization temperature, melt and crystallization enthalpies. Also, decreased the long period, increased the volume crystallinity, and caused reductions amorphous/crystalline interface and two‐phase model deviations. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44558.     

Evaluation of poly(methylsilane‐carbosilane) synthesized from methyl‐dichlorosilane and chloromethyldichloromethylsilane as a precursor for SiC

A new poly(methylsilane‐carbosilane) (PMSCS) for silicon carbide precursor was synthesized by Wurtz‐type copolycondensation of methyldichlorosilane (MeHSiCl₂) with chloromethyldichloromethylsilane (ClCH₂MeSiCl₂) and terminated with vinylmagnesium chloride (ViMgCl). The use of insufficient sodium made the reaction more economic and safe. By changing the ratios of two monomers and the end‐block agent, the properties of the obtained PMSCS and the C/Si ratio of its derived ceramic could be tuned. Upon pyrolysis at 1000 °C under argon, silicon carbide with nearly stoichiometric C/Si ratio and low oxygen content was obtained in 64% of ceramic yield. PMSCS showed high potential as an economical SiC ceramic precursor for the fabrication of SiC matrix, coating, and adhesives. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46610.     

Polypropylene with high melt flow rate and high isotacticity prepared by phosphate‐mixed external donors

High melt flow rate (MFR) of polypropylene can improve its processability and its high isotacticity is favor of keeping good mechanical properties of polypropylene. In this study, as a convenient and effective method, the mixture of phosphate and alkoxysilane as mixed external donors for Ziegler‐Natta catalyst is used to improve MFR of polypropylene. The MFR of polypropylenes prepared by mixed external donors is three to five time higher than that prepared by dicyclopentyl dimethoxysilane (Donor‐D) alone, which is attributed to broad molecular weight distribution and low molecular weight of polypropylene prepared by mixed external donors. In addition, isotacticity and lamella thickness of polypropylene prepared by mixed external donors containing triisopropyl phosphate or phenyl‐phosphonic acid dipentyl ester are very close to that prepared by Donor‐D, which lead to keep high thermal properties and good mechanical properties for the polypropylenes. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44704.     

Influence of chemical functionalization of carbon nanotubes on their dispersibility in alkyl methacrylate polymer matrix

Nanocomposites based on poly(methyl methacrylate) (PMMA) and poly(methyl methacrylate‐co‐octadecyl methacrylate) (M/O) matrices and four different types of multiwall carbon nanotubes: pristine, oxidized (MWCNT–COOH), methyl ester (MWCNT–COOCH₃), and dodecyl ester (MWCNT–COOC₁₂H₂₅) functionalized, were prepared in situ by radical (co)polymerization. The effectiveness of preparation of nanocomposites regarding dispersion and distribution of various MWCNT in polymer matrices was sized by Scanning electron microscopy. In case of PMMA matrix, the best dispersion and distribution were accomplished for MWCNT–COOCH₃ due to their chemical resemblance with polymer matrix. After the introduction of 10 mol % of octadecyl methacrylate in polymer matrix a fairly good dispersion and distribution of MWCNT–COOCH₃ were retained. The addition of 1 wt % of MWCNTs caused a significant reduction in the degree of polymerization of the PMMA matrix. But at the same time, the present MWCNTs increased storage modulus of PMMA nanocomposites except for dodecyl ester functionalized MWCNT. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46113.     

POSS Core star‐shape molecular hybrid materials: Effect of the chain length and POSS content on dielectric properties

A series of inorganic–organic molecular hybrids, poly(styrene‐co‐octavinyl‐polyhedral oligomeric silsesquioxane)s (PS‐POSSs), were synthesized, and their structures and properties were characterized by FTIR, ¹H‐NMR, ²⁹Si‐NMR, XRD, optical microscopy (OM), and atomic force microscopy (AFM). The chemical incorporation of POSS into polymer matrixes achieves uniform dispersion and makes the resultant hybrids display good film formability. The relationship between molecular structure of these hybrids and their dielectric constants and formation mechanism of low dielectric constant were investigated. The low dielectric constant of the hybrids mainly originates from the increase of free volume, involving the free volume of intrinsic porosity from POSS and an increase in the free volume owing to steric hindrance of bulky POSS. The latter plays a dominant role to increase the free volume and formation of low dielectric constant. Simultaneously, the polymer arm‐length has an important influence on the dielectric constant of the star‐type hybrids. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Strain rate dependent mechanical properties of a high‐strength poly(methyl methacrylate)

Strain rate dependency is an important issue for the mechanical response of materials in impact events. Dynamic mechanical properties of a high‐strength poly(methyl methacrylate) (PMMA) were studied by using split Hopkinson pressure bar technology. The maximum stress is enhanced with the increase of strain rate, and then keeps a constant with the further increase of strain rate, which is accompanied with a linear increase of fracture energy density. The critical data of strain rate and maximum stress were determined. Eyring's equation was applied for analyzing the influence factors, which relate to the hardening induced by strain rate and softening caused by adiabatic temperature rise. Inherent physical mechanisms were clarified and the strategies for designing advanced impact‐resistant polymers were proposed. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46189.     

Identification of relationship between the synthesis/process parameters and properties of a sol–gel‐derived polymer nanocomposite system

A Ti‐containing silicate‐based epoxy‐functional polymer nanocomposite system was synthesized by a sol–gel route with or without the introduction of a reflux process, which was followed by UV‐induced epoxy polymerization. Influences of synthesis and process parameters, including Ti content, sol ageing, reflux process, and UV‐irradiation on various properties of the system were detailed. It was demonstrated that the introduction of a reflux process during the sol–gel synthesis could significantly modify the chemical and physical properties of the resultant material system along with other parameters such as Ti content. Overall results showed that the synthesis and process parameters examined could be employed to modify the microstructure, and to tune the final properties of this polymer nanocomposite system. The technique described herein, therefore, could be used to develop a new process regime to obtain materials of this type with desired properties, which might potentially be employed in certain applications such as dental restoration. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Effect of the comonomer content on the solid‐state mechanical and viscoelastic properties of poly(propylene‐co‐1‐butene) films

In this study, we quantified the thermal and solid‐state mechanical and viscoelastic properties of isotactic polypropylene (i‐PP) homopolymer and poly(propylene‐1‐butene) copolymer films having a 1‐butene ratio of 8, 12, and 14 wt %, depending on the comonomer content. The uniaxial tensile creep and stress‐relaxation behaviors of the samples were studied in a dynamic mechanical analyzer at different temperatures. The creep behaviors of the samples were modeled with the four‐element Burger equation, and the long‐term creep strains were predicted with the time–temperature superposition method. The short‐term mechanical properties of the samples were also determined with tensile and impact testing at room temperature. We found that the Young's modulus and ultimate strength values of the samples decreased with increasing amount of 1‐butene in the copolymer structure. On the other hand, the strain at break and impact strength values of the samples improved with increasing amount of 1‐butene. Creep analysis showed that i‐PP exhibited a relatively lower creep strain than the poly(propylene‐co‐1‐butene)s at 30 °C. However, interestingly, we discovered that the temperature increase resulted in different effects on the creep behaviors. We also found that short‐chain branching improved the creep resistance of polypropylene at relatively high temperatures. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46350.     

Rigid polyurethane–clay nanocomposite foams: Preparation and properties

Rigid polyurethane–clay nanocomposite foams considered in this work are made with different clay types and for different clay concentrations. The densities of the foams are in the range of 140–160 kg/m³ with possible application as structural materials and for underwater buoyancy‐related uses. Wide‐angle X‐ray diffraction and transmission electron microscopy studies confirm the formation of nanocomposites. The compressive modulus and the storage modulus of the foams increase and the mean cell size decreases with addition of clay. However, the hydraulic resistance of the nanocomposite foams, a measure of the strength of the foam lamellae, is lower than that of the foams without clay. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2802–2809, 2007     

Synthesis and characteristics of pectiniform polyurethane‐modified polycarboxylate at room temperature

In this article, modified polyurethane prepolymer was synthesized by segmental synthesis method using isophorone diisocyanate, hydroxyl‐terminated silicone, polyether glycol dimethylolpropionic acid as raw materials. After that, pectiniform polycarboxylate, of which side chains were in roughly the same polymerization degree and main chains were in different lengths, was synthesized at room temperature in initiation system of hydrogen peroxide, ascorbic acid, and persulfate. Moreover, influence of various factors on the synthesis of polyurethane‐modified polycarboxylate at room temperature was discussed in detail and optimal synthesis process was determined. Results showed that redox initiation system, increasing initiator and monomer concentration, and extending reaction time needed to be adopted to complete the reaction. However, when the reaction time was over 4 h, water reducing of polycarboxylate declined rapidly. In addition, it could be found in Fourier transform infrared spectrum analysis that the ? C?C? double bonds in acrylic acid were opened and polymerized, macromolecular chain segments were successfully connected to polyoxyethylene chain segment, and resulting polycarboxylic acid molecule contained hydroxy, carboxyl, methyl, ester group, and other groups. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45873.     

Waterborne poly(urethane‐urea) gas permeation membranes for CO2/CH4 separation

In this work, dense membranes from aqueous dispersions of poly(urethane‐urea) (PUU) based on poly(propylene glycol) (PPG) and a block copolymer composed of poly(ethylene glycol) (PEG) and poly(propylene glycol) (PPG), EG‐b‐PG, with 7 wt % of the former were obtained. Nonpolluting formulations were synthesized with proportions of PPG and EG‐b‐PG as 1:0, 1:1, 1:3, and 3:1 in terms of equivalent number ratios. The effect of small and gradual increases in PEG segments was evaluated for the permeability of pure CO₂, CH₄, and N₂, at room temperature. Slight increases in PEG‐based segments in PUU promoted some remarkable properties, which led to a simultaneous increase in CO₂ permeability and ideal selectivity for CH₄ (300%) and N₂ (380%). Infrared spectroscopy showed that the PEG portions induced hydrogen bonds between ? NH of urethane and ether groups in the PEG portions, which promoted ordering of the flexible segments, confirmed by X‐ray diffractometry and small‐angle X‐ray scattering. Diffractometry techniques also confirmed the absence of crystalline domains, as did dynamic mechanical analysis. The produced membranes showed performance above Robeson's 2008 upper bound and seemed to be a superior polymeric material for CO₂/CH₄ and CO₂/N₂ separation. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46003.     

Polyurethane/clay nanocomposites with improved helium gas barrier and mechanical properties: Direct versus master‐batch melt mixing route

Thermoplastic polyurethane (TPU)/clay nanocomposite films were produced by incorporation of organo‐modified montmorillonite clay (Cloisite 30B) in TPU matrix by two different melt‐mixing routes (direct and master‐batch‐based mixing), followed by compression molding. In master‐batch mixing where the master‐batch was prepared by mixing of clay and TPU in a solvent, better dispersion of clay‐layers was observed in comparison to the nanocomposites produced by direct mixing. As a consequence, superior mechanical and gas barrier properties were obtained by master‐batch mixing route. The master‐batch processing resulted in 284 and 236% increase in tearing strength and tearing energy, respectively, with 5 wt % clay‐loading. Interestingly, in case of master‐batch mixing, the tensile strength, stiffness as well as breaking extension increased simultaneously up to 3 wt % clay‐loading. The helium gas permeability reduced by about 39 and 31% for the TPU/clay nanocomposites produced by mater‐batch and direct mixing routes, respectively, at 3 wt % loading of clay. Finally, the gas permeability results have been compared using three different gas permeability models and a good correlation was observed at lower volume fraction of clay. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46422.     

Structural,mechanical, and thermal properties of 3D printed L‐CNC/acrylonitrile butadiene styrene nanocomposites

3D printing has been extensively applied in human‐related activities, and therefore the 3D printed nanocomposites became more popular and important in end‐use products. In the present study, we use lignin‐coated cellulose nanocrystal (L‐CNC) to reinforce 3D printed acrylonitrile butadiene styrene (ABS) and explore the effect of L‐CNC on the structural, mechanical, and thermal properties of 3D printed L‐CNC/ABS nanocomposites. The results indicate that the addition of L‐CNC foams the ABS and decreases the density of 3D printed L‐CNC/ABS nanocomposites. However, the tensile modulus and storage modulus increase by adding 4% L‐CNC. The thermal stability of 3D printed L‐CNC/ABS nanocomposites is also significantly improved as indicated by an increase in the maximum degradation temperature. The morphology of the nanocomposites reveals good dispersion and interfacial adhesion between L‐CNC and ABS. The finding indicates that the 3D printed nanocomposites become lighter and stiffer with addition of L‐CNC, which will have great potential to be applied in end‐use products. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45082.     

PANI/PPY blend thin films electrodeposited for use in EGFET sensors

Galvanostatic electrodeposited thin films of polyaniline (PANI)/polypyrrole (PPY) blend were tested as chemical sensors and evaluated according to the relative monomer concentration in polymerization solution aiming to obtain a reliable reference field‐effect transistor able to be used as contrast sensing film. The blend material presented properties that can be controlled by the polymerization process. The films were produced using aniline (0.25 M) and pyrrole (0.25 M) mixed in five different proportions (90/10, 70/30, 50/50, 30/70, 10/90) with HCl (1.0 M) in an aqueous solution. The current density was 1 mA/cm² for 300 s. The films were analyzed by their chronopotentiometric curves, thickness, reflectance spectroscopy, optical color parameters, and surface morphology. The characteristics and properties analyzed were correlated to the relative monomer concentration in the polymerization solution. The polymerization of PANI is favorable in aqueous acid solution compared to PPY, which resulted in thin films with properties varying from PANI down to PPY. The blend films presented controllable sensitivity when applied as sensing stage in field‐effect transistor devices as function of the relative monomer concentration. The sensitivity varied from 57 ± 1 mV/pH for the PANI sample, down to 25 ± 1 mV/pH for the PPY sample, presenting an exponential behavior. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46625.     

Effects of 4,4′‐diaminodiphenyl ether on the structures and properties of isocyanate‐based polyimide foams

A series of thermal insulation, acoustic absorption isocyanate‐based lightweight polyimide (PI) foams with 4,4′‐diaminodiphenyl ether (ODA) units were prepared from polyaryl polymethylene isocyanate (PAPI) and the esterification solution derived from pyromellitic dianhydride (PMDA) and ODA. The structures and properties of the PI foams prepared with different molar ratio of ODA/PMDA were investigated in detail. The results show that the ODA units have great influence on the foam properties. With the increase of the ODA units, the density decreases firstly and then increases. When the molar ratio of ODA/PMDA is 3/10, the foam reaches the minimum density (13.7 kg/m³). Moreover, with increasing the ODA units, the acoustic absorption properties increase firstly and then decrease owing to the variation of the average cell diameter of the PI foams. All PI foams show excellent thermal stability, and the 5% and 10% weight loss temperature are in the range of 250–270 °C and 295–310 °C, respectively. In addition, the PI foams present low thermal conductivity and thermal diffusivity. Furthermore, the mechanical property was also evaluated and the compressive strength of the PI foams is in the range of 33.0–45.7 kPa. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46029.     

Polyurethane‐acrylic hybrid emulsions with high acrylic/polyurethane ratios: Synthesis,characterization, and properties

Allyl polyoxyethylene ether (APEE) was used as coupling agent between polyurethane (PU) and acrylic polymer (AC) to synthesize stable waterborne polyurethane‐acrylic (PU‐AC) hybrid emulsions with high AC/PU weight ratio ranged from 45/55 to 70/30. The effect of the AC/PU weight ratio and the acrylate type including methyl methacrylate (MMA), butyl acrylate (BA) and mixture of them on the properties of the synthesized emulsions and resultant films were investigated. The research results showed that the colloidal particle of the emulsions behaved core‐shell structure, and the copolymers were not crosslinked. An increase in the AC/PU weight ratio led to an increase in the average particles size and the particle size distribution, but decrease in the viscosity of the emulsions. Meanwhile, the molecular weight distribution of the copolymers became wide, and the tensile stress, shore A hardness, storage modulus, glass transfer temperature, water resistance, and water contact angle of the resultant films increased, except that the films of PU‐BA were too soft to determine their mechanical properties. MMA and BA can provide the PU‐AC hybrid emulsions with very different properties, and which can be adjusted according to the special application. It was suggested that APEE can not only built up chemical bonds between PU and AC, but also increase the self‐emulsifying ability in the emulsion polymerization due to its hydrophilic ethylene oxide and carboxylic groups, resulting in that PU‐AC hybrid emulsions with high AC/PU ratio can be obtained by this method. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44488.     

Effect of acrylic monomer content on the properties of waterborne poly(urethane‐urea)/acrylic hybrid materials

Stable waterborne poly(urethane‐urea) (WBPU; soft segment content: 57%; dimethylol propionic acid: 19 mol %/5.8 wt %)–polyacrylate(methyl methacrylate/n‐butyl acrylate) (weight ratio: 4/1) hybrid latex (emulsions) with different acrylic contents [0, 10, 20, 30, and 40 wt % based on poly(urethane‐urea)] and without external surfactant were successfully prepared by in situ polymerization during a prepolymer mixing process. However, the as‐polymerized hybrid latex containing 50 wt % of acrylic monomer content was found to be unstable, indicating that about 50 wt % of acrylic monomer content was beyond the limit value of self‐emulsifying ability of WBPU anionomer prepared in this study. The breadth of particle size distribution of hybrid latex increased markedly from 20–75 to 55–275 nm with increasing acrylic monomer content from 0 to 40 wt %. The pristine WBPU and hybrid latex samples containing 10, 20, and 30 wt % of acrylic monomer showed unimodal distributions, whereas the hybrid sample having 40 wt % acrylic monomer content displayed a bimodal distribution with the broadest breadth. As acrylic monomer content increased, the yield point of stress–strain curve, hardness, glass transition, and water resistance of hybrid film samples increased, whereas their abrasion resistance, elongation at break, and elasticity decreased. The tensile strength of hybrid film samples (10–30 wt % of acrylic monomer content) was almost the same as that of pristine WBPU film sample, indicating the intimate molecular mixing between poly(urethane‐urea) and polyacrylate molecules in hybrids. However, the hybrid sample having 40 wt % acrylic monomer showed significantly diminished performance, which might be due to the deviation from intimate molecular mixing. From these results, the optimum acrylic monomer content was found to be about 30 wt %, which realized reasonably advantages of both poly(urethane‐urea) and acrylic polymer. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Preparation,mechanical properties of waterborne polyurethane and crosslinked polyurethane‐acrylate composite

The waterborne polyurethane (PU) prepolymer was first prepared based on isophorone diisocyanate, polyether polyol (NJ‐210), dimethylol propionic acid (DMPA), and hydroxyethyl methyl acrylate via in situ method. The crosslinked waterborne polyurethane‐acrylate (PUA) dispersions were prepared with the different functional crosslinkers. The chemical structures, optical transparency, and thermal properties of PU and PUA were confirmed by Fourier transform infrared spectrometry, ultraviolet–visible spectrophotometry, and differential scanning calorimetry. Some physical properties of the aqueous dispersions such as viscosity, particle size, and surface tension were measured. Some mechanical performances and solvent resistance of PUA films were systemically investigated. The experimental results showed that the particle sizes of the crosslinked PUA aqueous dispersions were larger than the PU and increased from 57.3 to 254.4 nm. When the ratios of BA/St, BA/TPGDA, and BA/TMPTA were 70/30, PUA films exhibited excellent comprehensive mechanical properties. The tensile strength and elongation at break of the film were 2.17 MPa and 197.19%. When the ratio of BA/St was 30/70, the film had excellent water resistance and was only 6.47%. The obtained PUA composites have great potential application such as coatings, leather finishing, adhesives, sealants, plastic coatings, and wood finishes. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Plastic waste minimization: Compatibilization of polypropylene/polyamide 6 blends by polyalkenyl‐poly‐maleic‐anhydride‐based agents

The present article discloses the properties improvement in PP/PA 6 blends by new type experimental coupling additives. By the experimental agents especially the tensile properties could be improved. For example, the tensile strength and the elongation were 16.5 MPa and 4.4% without additive, which increased to 25.5, 20.1, 46.8 MPa and 8.1, 6.4, 8.6% in specimens containing polyalkenyl‐poly‐maleic‐anhydride‐amide, polyalkenyl‐poly‐maleic‐anhydride‐ester, and MA‐grafted‐low‐polymer additives, respectively. DSC curves shows that compatibilizers influenced thermal properties of the polymer blends and reveal affecting of crystalline phase formation process in the blends due to the compatibilization step. Additives A and B rather leads to influencing of PA crystallinities. According to the SEM and FTIR analysis well separated polypropylene and polyamide phases was observed in case of specimens absence of additives but only one well distributed phase by the applying of the synthetized coupling agents. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013