Compressive shape memory behavior of spring‐shaped polylactic acid alloy type

This article presents an experimental study on the shape memory behavior of blends of thermoplastic polyurethane (TPU) and biodegradable polylactic acid (PLA) at the PLA/TPU weight ratios of 70/30 (PT7030) and 50/50 (PT5050). The manufactured springs were studied comprehensively based on their morphological and thermal properties. Scanning electron microscopy micrographs were captured, which verified that TPU was compatible with PLA. The wide‐angle X‐ray diffraction suggested that the crystallinity of PLA was enhanced in the presence of TPU. In order to determine the shape recovery properties [shape recovery ratio (R_r), shape fixing ratio (R_f), and shape recovery force (F_r)], the samples programmed at three different temperatures (T_p) of 70, 80, and 90 ° and at various recovery temperatures (T_r) over 40 to 90 ° , were studied. In general, the spring made with PT7030 showed higher R_r, R_f, and F_r values. The highest R_r (99%) was obtained at programmed temperature (T_p) of 70 ° and recovery temperature (T_r) of 90 ° . However, the R_r value for this spring programmed at 70 ° and recovered near body temperature was 50% with F_r of 1.4 N. Furthermore, the highest F_r (15.6 N) was observed in the spring made of PT7030 programmed at 80 ° and recovered at T_r of 78 ° . © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45115.     

Heat‐ and light‐induced thiol‐ene oligomerization of soybean oil‐based polymercaptan

Polymercaptanized soybean oil (PMSO), the product of a thiol‐ene reaction between soybean oil and hydrogen sulfide, is a material of interest as a lubricant additive and polymer precursor. We investigated with gel permeation chromatography, nuclear magnetic resonance (one‐dimensional and two‐dimensional), gas chromatography–mass spectrometry, and viscometry the changes that occur with PMSO upon heating or ultraviolet irradiation. The observed changes were due to a further thiol‐ene reaction between the thiol groups and the residual unsaturation. The formation of oligomers was a result of new sulfide bridges. Additionally, tetrahydrothiophene moieties were detected. An almost linear increase of the average molecular weight (MW) and the polydispersity index (PDI) was observed upon heat treatment [number‐average MW ( ) = 1180 Da, PDI = 1.32 for PMSO, = 1720 Da, PDI = 2.17 for PMSO that was heated for 1000 h at 130 °C]. PDI correlated best with the z‐average MW. The was the best predictor of the viscosity. For samples with close , the higher PDI corresponded to a higher viscosity index. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46150.     

Investigation and modelling of damping mechanisms of magnetorheological elastomers

Damping in MREs is considered to be ascribed to viscous flow of the rubber matrix, interfacial damping at the interface between the magnetic particles and the matrix and magnetism induced damping. In this study, individual components in MREs that contribute to material damping were investigated. A model was developed to include viscous flow of the rubber matrix, interfacial damping and magnetism induced damping to give the total damping capacity of MREs ( )It was found that depends on frequency, iron sand content, strain amplitude and is independent of the applied magnetic field over saturation magnetization. The proposed model was assessed experimentally using a series of isotropic and anisotropic MREs. Comparison between tan δ with showed that matched the experimental trends with average percentage difference of 8.1% and 21.8% for MREs with modified iron sand unmodified iron sand, respectively. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43247.     

Synthesis of aminated glycidyl methacrylate grafted rice husk and investigation of its anion‐adsorption properties

In this study, we focused on the synthesis, characterization, and adsorption capacity testing of aminated glycidyl methacrylate grafted rice husk (RH‐g‐GMA–Am). Our goal was to obtain a high‐performance surface for the adsorption of various anions. Glycidyl methacrylate grafted rice husk (RH‐g‐GMA) was prepared by the graft copolymerization of glycidyl methacrylate with rice husk; the product was further subjected to an amination reaction. The surface properties, sorption characteristic functional groups, isotherm and kinetic studies, pore diffusion models, and effects of the temperature and pH on the material properties were studied under batch conditions. The IR spectroscopy results show additional surface functional groups for RH‐g‐GMA–Am. The adsorptions of and on RH‐g‐GMA–Am were found to follow pseudo‐second‐order kinetics; this indicated a possible dominant role played by chemisorption. The rate‐limiting step for mass transfer was found to be boundary layer diffusion. Furthermore, the sorption isotherms for and fit the Langmuir model. The amination of RH‐g‐GMA drastically increased the removal efficiency from 3 to 82% and from 6 to 93% for and , respectively. Moreover, RH‐g‐GMA–Am exhibited a better removal efficiency in the pH range of 4–6.5. Regeneration studies revealed that the surface of RH‐g‐GMA–Am could be regenerated repetitively by simple acid washing with an insignificant decrease in the active surface for consecutive adsorptions. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43002.     

Copolymers from methyl methacrylate and butyl acrylate with hyperbranched architecture

This is a first report of the synthesis and characterization of acrylic copolymers from methyl methacrylate (MMA) and butyl acrylate (BA) with hyperbranched architecture. The copolymers were synthesized using a free radical polymerization (Strathclyde method) in emulsion technique. Divinyl benzene was used as the brancher which acted as a comonomer and 1‐dodecanethiol was used as a chain terminating agent. A linear copolymer from MMA and BA was also synthesized for comparison. The hyperbranched architecture was established from spectroscopic and rheological measurements. The gel permeation chromatography showed all hyperbranched copolymers were low molecular weight with lower polydispersity index (PDI) ( 23,000, PDI ～ 2.00) compared to the linear grade ( 93,000, PDI ～ 2.20). They were more spherical and achieved lower viscosity (yet higher solubility, >90%) than the linear grade (<50%) which was mostly open ended. Lower viscosity at equivalent solid content made the hyperbranched polymers a potential binder for adhesive and coating application. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45356.     

Effect of K0.5Na0.5NbO3 filling particles on the charge carrier trap distribution of polyimide films

Polyimide (PI) films filled with K_0.5Na_0.5NbO₃ (KNN50) particles at different weight 0, 5, 10, and 15 wt % had been prepared by in‐situ dispersion polymerization process. The thermally stimulated current (TSDC) method was used to investigate the charge carrier trap levels and their distribution of the composite films. The TSDC spectra show that pure film has ‐peaks and ‐peak, but the composite films only have ‐peaks and an extraordinary peak at high temperature region. The trap parameters were calculated by an approximate model, and the results indicate that charge released of the shallow traps show a nonlinear behavior. The trap energies decrease from 0.879–0.968 eV to 0.549–0.839 eV with the increase of the KNN50 content. The surface and interface between KNN50 and PI matrix was considered to the variation of the trap levels. The extraordinary peak of the composite films was correlated with the phase transition of the KNN50 particles. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39828.     

Counterion-Induced Cationic Flexible Nanoparticle Catalytic of Piperidinolysis of Phenyl Salicylate

The removal of PSa^? from bulk aqueous phase to the pseudo‐micellar phase by halobenzoate counterion X is responsible for the monotonic increase in k_obs (pseudo first‐order rate constants) with the increase in the values of [MX] where MX = sodium salts of 2‐, and 4‐halobenzoic acids. The values of ion exchange constants, or for X = 2‐ and 4‐halobenzoate ions in the presence of tetradecyltrimethylammonium bromide (TTABr) were calculated from the apparent catalytic rate constants, ^Xk_cat which represent the catalytic effect of CFN. Larger values of or were observed for X = 4‐halobenzoate ions than that for X = 2‐halobenzoate ions due to isomeric factors. The values of or determined in the presence of TTABr were compared with previously determined or values in the presence of cetyltrimethylammonium bromide (CTABr). The values of or are nearly 8 ~ 9‐fold larger for 4‐IBz^?, 4‐BrBz^? and 4‐ClBz^? compared to the respective values of X = 2‐IBz^?, 2‐BrBz^? and 2‐ClBz^?. The values of or for X = 4‐FBz^? is nearly 3‐fold larger than that for X = 2‐FBz^?. The values of or for X = 2‐ and 4‐halobenzoates are significantly smaller in the presence of TTABr than these in the presence of CTABr nanoparticles.     

Synthesis and characterization of dendritic polypyrrole silver nanocomposite and its application as a new urea biosensor

Polypyrrole and its silver nanocomposite were electrochemically synthesized from aqueous solutions containing pyrrole, potassium chloride (KCl) (system A); pyrrole, KCl, and an anionic surfactant sodium dodecyl sulphate (NaDS) (system B); and pyrrole, silver nitrate, NaDS (system C). Compact and dendritic patterns were observed depending on experimental conditions. The aggregates were characterized by powder X‐ray diffraction, energy‐dispersive X‐ray spectroscopy, scanning electron microscopy, high resolution transmission electron microscopic (HRTEM), and thermal studies (TG/DTG). HRTEM studies indicate that the particle size of PPy‐Ag nanocomposite is ～30 nm. TG studies revealed that systems B and C, have different thermal behavior. Potassium ion selective electrodes were constructed using systems A, B, and C. The electrode prepared with PPy‐Ag nanocomposite showed nernstian behavior with maximum slope of 57 mV. ion‐selective electrode was also constructed for this system based on nonactin‐impregnated PVC matrix membrane. Urease enzyme was immobilized at the surface of as made ion‐selective electrode to develop urea biosensor showing good detection limit. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45705.     

NMR spectroscopic study of chemical equilibria in solutions of formaldehyde,water, and butynediol

Liquid mixtures of formaldehyde, water, and butynediol are complex reacting multicomponent systems in which formaldehyde forms oligomers both with water and butynediol. ‐ and ‐NMR spectra of these mixtures are elucidated. The species distribution of the oligomers is quantitatively determined by ‐NMR spectroscopy. The measurements cover temperatures from 293 to 366 K, overall formaldehyde mass fractions from to , and overall butynediol mass fractions from to . A mole fraction‐based and an activity‐based model of the chemical equilibrium in the studied system are developed and chemical equilibrium constants are reported. © 2017 American Institute of Chemical Engineers AIChE J, 63: 4442–4450, 2017     

Preparation of nonwoven mats of electrospun poly(lactic acid)/polyaniline blend nanofibers: A new approach

The preparation of nonwoven mats of electrospun poly(lactic acid)/polyaniline (PANI) blend nanofibers faces some critical challenges that will be addressed in the present work. The challenges are in achieving high and adjustable content of PANI while keeping the spinnable solution nonagglomerated with no need to further filtration that might lead to wrong estimation of PANI content in the mat. We report an unprecedented content of 40% wt of PANI that is achieved using a new two‐step procedure. It is based on: (1) the preparation of the spinnable solution from a friable nonagglomerated and readily dispersible PANI: ‐TSA powder and (2) the use of an optimized mixture of ‐cresol/dichloromethane. The obtained nanofiber mats are characterized by FTIR and UV–vis spectroscopy. The morphology and the thermal stability of the nanofibers are investigated by scanning electron microscopy (SEM) and differential scanning calorimetry (DSC). The amorphous structure of the nanofibers is verified using XRD measurements. The DC‐conductivity of these blend nanofibers is found to be far larger than the published DC‐conductivity values for blend nanofibers of PANI with PLLA or with other polymers. This is attributed to the high content of PANI in the blend and to the role played by ‐cresol as a secondary dopant. The investigation of the aging effect on the DC‐conductivity reveals an exponential decrease with a characteristic time of weeks. The electrical impedance spectroscopy (EIS) shows a pure ohmic behavior of the blend mat. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43687.     

Mass transfer coefficient of tubular ultrafiltration membranes under high‐flux conditions

The effect of suction flow on the mass transfer coefficient of tubular ultrafiltration membranes, in particular that under a high‐flux condition, was studied. We pointed out that is proportional to under turbulent conditions, and that the proportional constant, b, exceeds 0.023 when the effect of suction flow is not negligible. We conducted the velocity variation method using ultrafiltration membranes with MWCOs of 20k and 100k and dextrans having molecular weights of 40,000 and 70,000 at the conditions, where exceeded . We demonstrated that the effect of suction flow includes not only flux but also the diffusion coefficient of solute, and that the ratio of the flux to the diffusion coefficient, expressed as , is an important index. Finally, we concluded that , when is smaller than , giving the Deissler equation itself, and that , when exceeds . © 2017 American Institute of Chemical Engineers AIChE J, 64: 1778–1782, 2018     

Mechanism of internal and external electron donor effects on propylene polymerization with MgCl2‐supported Ziegler–Natta catalyst: New evidences based on active center counting

Two TiCl₄/Di/MgCl₂ type supported Ziegler–Natta catalysts were prepared by loading dibutylphthalate or dicyclopentyldimethoxysilane (DCPDMS) (internal donor, Di) and TiCl₄ on activated δ‐MgCl₂ in sequence, and a blank catalyst was prepared by loading TiCl₄ on the same δ‐MgCl₂ without adding Di. These catalysts have similar specific surface area and pore size distribution, thus form a suitable base for comparative studies. Propylene polymerization with the catalysts was conducted in n‐heptane slurry using triethylaluminum (TEA) as cocatalyst, and the effects of Di as well as De (external donor, in this work it was DCPDMS) on the number of active centers, the distribution of active centers among three polypropylene (PP) fractions (isotactic, medium isotactic, and atactic PP chains), and chain propagation rate constants of the PP fractions were studied by counting the number of active centers in the PP fractions using a method based on selective quench‐labeling of the propagation chains by 2‐thiophenecarbonyl chloride. When De was not added in the polymerization, introducing a phthalate type Di in the catalyst evidently changed the active center distribution by enhancing the proportion of active centers producing isotactic PP (iPP) ( ), but scarcely changed reactivities of the three groups of active centers forming the three fractions. When the De was added in the polymerization system with TiCl₄/phthalate/MgCl₂ catalyst, further shifting of active center distribution in favor of took place, meanwhile reactivities of the three groups of active centers also remarkably changed in favor of . Mutual effects of these changes led to overwhelming dominance of iPP production in the TiCl₄/Di/MgCl₂–TEA/De system (Di = phthalate, De = alkoxysilane). In contrast, though using alkoxysilane as Di also caused shifting of active center distribution in favor of when De was not added, addition of alkoxysilane De caused reverse shifting of active center distribution in favor of those producing PP of lower stereoregularity. This unfavorable change largely counteracted the reactivity changes in favor of caused by the De, rendering the catalytic system rather poor isospecificity. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46605.     

Influence of 2,2′,6,6′‐tetramethyl biphenol‐based anion‐exchange membranes on the diffusion dialysis of hydrochloride acid

Quaternary ammonium functionalized poly(arylene ether) (QPAE‐Br) membranes based on 2,2′,6,6′‐tetramethyl biphenol for diffusion dialysis (DD) were designed and successfully fabricated via nucleophilic substitution polycondensation, bromination, film casting, and quaternization. The structures, thicknesses, ion‐exchange capacities (IECs), water uptakes, swelling ratios, ion conductivities, and mechanical properties of QPAE‐Br were used to characterize the membranes. The influence of the membrane structures on the DD performances was investigated by DD tests of simulated industrial pickling wastewater (1 mol/L HCl, 0.1 mol/L FeCl₂). The DD results show QPAE‐a (IEC = 1.51 mmol/g) as the best DD candidate. Predialysis treatments further improved the DD performances of QPAE‐Br. QPAE‐a exhibited an excellent proton diffusion coefficient ( ) of 0.033 m/h and a high separation factor (S) of 95.45 after the predialysis treatment at room temperature; these values were much higher than those of the commercial DF‐120B membrane (0.004 m/h for and 24.3 for S at 25 °C) and other reported DD membranes. QPAE‐a has great potential for acid recovery via DD. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45333.     

Self‐synthesized epoxy terminated polydimethylsiloxane with various molecular weights toughening epoxy resin

Polydimethylsiloxane terminated by epoxy group (EP‐PDMS) with various molecular weight ( ) were synthesized by 1,3‐bis[3‐(2,3‐epoxypropoxy)‐propyl]‐1,1,3,3‐tetramethyldisiloxane (DOTMDS) and dimethylcyclosiloxane (D_n). The epoxy value measured by potentiometric titration, were 0.161, 0.092, 0.065, 0.044 mol/100 g, and the (calculated from epoxy value) 1,242, 2,174, 3,077, 4,545 g/mol, respectively (corresponding to EP‐PDMS1, 2, 3, 4). With the increasing ratio of D_n/DOTMDS, we can see the increase of and the decrease of epoxy group content according to FTIR result. Then these EP‐PDMS were used to improve the toughness of the epoxy resin (diglycidyl ether of bisphenol A, DGEBA). Mechanical tests showed that, the impact strength of the epoxy resin was improved by EP‐PDMS. The toughening effect was decreased when EP‐PDMS with relative higher was used. This was ascribed to that the EP‐PDMS with high was easier to agglomerate, and the active group was easier to be embedded which in turn resulted in lower toughening efficiency. This was also confirmed by scanning electron microscopy results. J. VINYL ADDIT. TECHNOL., 24:268–274, 2018. © 2016 Society of Plastics Engineers     

Defect engineering on phase structure and temperature stability of KNN‐based ceramics sintered in different atmospheres

Lead‐free MnO‐doped 0.955K_0.5Na_0.5NbO₃‐0.045Bi_0.5Na_0.5ZrO₃ (Abbreviated as KNN‐0.045BNZ) ceramics have been prepared by the conventional solid‐state sintering method in reducing atmosphere ( = 1 × 10^?10 atm) and air. For ceramics sintered in reducing atmosphere, only Mn²⁺ ions exist in ceramics who preferentially occupy the cation vacancies in A‐site at x = 0.2‐0.4, whereas Mn²⁺ ions substitute for Zr⁴⁺ ions in B‐site to form defects () at x > 0.4. For ceramics sintered in air, mixed Mn²⁺, Mn³⁺, and Mn⁴⁺ ions coexist here. The Mn²⁺ ions preferentially occupy the cation vacancies in A‐site at x = 0.2‐0.4 and then Mn²⁺ ions substitute for Zr⁴⁺ ions in B‐site at x > 0.4. Meanwhile, the Mn³⁺ ions and Mn⁴⁺ ions substitute for Nb⁵⁺ ions in B‐site to form defects () at x = 0.2‐0.8. The (, , and ) dipolar defects show a positive dipolar defect contribution (DDC) to the , whereas the dipolar defects () show a negative DDC to the . The dipolar defects ( ‐ and ) can help improve the temperature stability of . The 0.4% MnO‐doped KNN‐0.045BNZ ceramics sintered in reducing atmosphere show excellent piezoelectric constant d₃₃ = 300 pC/N and 0.2% MnO‐doped KNN‐0.045BNZ ceramics sintered in air possess optimal piezoelectric constant d₃₃ = 290 pC/N.     

A rigorous method to evaluate the consistency of experimental data in phase equilibria. Application to VLE and VLLE

This work forms part of a broader study that describes a methodology to validate experimental data of phase equilibria for multicomponent systems from a thermodynamic‐mathematical perspective. The goal of this article is to present and justify this method and to study its application to vapor–liquid equilibria (VLE) and vapor–liquid–liquid equilibria (VLLE), obtained under isobaric/isothermal conditions. A procedure based on the Gibbs‐Duhem equation is established which presents two independent calculation paths for its resolution: (a) an integral method and (b) a differential method. Functions are generated for both cases that establish the verification or consistency of data, δψ for the integral test and δζ for the differential approach, which are statistically evaluated by their corresponding average values [ , ], and the standard deviations [ , ]. The evaluation of these parameters for application to real cases is carried out using a set of hypothetical systems (with data generated artificially), for which the values are adequately changed to determine their influence on the method. In this way, the requirements of the proposed method for the data are evaluated and their behavior in response to any disruption in the canonical variables (p,T, phase compositions). The conditions for thermodynamic consistency of data are: , , , and . In systems with VLLE, in addition to the previous criteria, must occur that: and . The new proposed method has been tested with a set of 300 experimental binary systems, biphasic and triphasic, obtained from published bibliography, and the results are compared with those of other tests commonly used for testing thermodynamic consistency. The results show that the greater rigor of the proposed method is mainly due to the simultaneous verification of various independent variables. As a result, the conditions for the new test are verified for fewer systems than using other tests mentioned in the literature (i.e., Fredenslund‐test and direct of Van Ness). Its unique application is sufficient to ensure the consistency of experimental data, without using other tests. © 2017 American Institute of Chemical Engineers AIChE J, 2017     

Cationic effect of charge compensation on the sulfide capacity of aluminosilicate slags

The effect of CaO on the sulfide capacity of CaO‐Al₂O₃‐SiO₂ slags was studied from the viewpoint of the ionic structure of alumina in slag. The aluminum coordination number was analyzed using ²⁷Al 500‐MHz solid nuclear magnetic resonance spectroscopy and the results were compared with those of the sulfide capacity analysis. The sulfide capacity of slag, in the peralkaline region (), exhibited a linear relationship with respect to basicity () as excess free Ca²⁺ formed a 4‐coordinated aluminum unit structure (^[IV]Al; ) and stabilized the sulfide ions (). However, sulfide capacity in the peraluminous region () exhibited a nonlinear relationship with respect to basicity () owing to the structure of higher‐coordinated aluminum units (^[V]Al, ^[VI]Al; Al³⁺) and the relative lack of Ca²⁺. Therefore, the sulfide capacity of high Al₂O₃‐bearing slags strongly depended on the basicity () and stability of sulfide ions (), which depended on the competitive behavior of Ca²⁺ owing to the structural changes in Al₂O₃. The effect of the aluminum coordination number on the sulfide capacity was discussed in detail using an analysis of the slag structure and thermodynamics model.     

Pressure drop through platinized titanium porous electrodes for cerium‐based redox flow batteries

The pressure drop, , across a redox flow battery is linked to pumping costs and energy efficiency, making fluid properties of the electrolyte important in scale‐up operations. The at diverse platinized titanium electrodes in Ce‐based redox flow batteries is reported as a function of mean linear electrolyte velocity measured in a rectangular channel flow cell. Darcy's friction factor and permeability vs. Reynolds number are calculated. Average permeability values are: 7.10 × 10^?4 cm² for Pt/Ti mesh, 4.45 × 10^?4 cm² for Pt/Ti plate + turbulence promoters, 1.67 × 10^?5 cm² for Pt/Ti micromesh, and 1.31 × 10^?6 cm² for Pt/Ti felt. The electrochemical volumetric mass transport coefficient, , is provided as a function of . In the flow‐by configuration, Pt/Ti felt combines high values with a relatively high , followed by Pt/Ti micromesh. Pt/Ti mesh and Pt/Ti plate gave a lower but poorer electrochemical performance. Implications for cell design are discussed. © 2017 American Institute of Chemical Engineers AIChE J, 64: 1135–1146, 2018     

Viscoelastic properties of borax loaded CMC‐g‐cl‐poly(AAm) hydrogel composites and their boron nutrient release behavior

Borax (Na₂B₄O₇, 10.5% Boron) loaded CMC‐g‐cl‐poly(AAm) hydrogel composites were prepared by in situ grafting of acrylamide on to sodium carboxymethyl cellulose in the presence of borax by free radical polymerization technique to develop slow boron (B) delivery device. The composition, morphology, and mechanical properties of synthesized composites were studied by X‐ray diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy, texture analyser, and dynamic shear rheometer. Characterization revealed formation of borate ion ( ) from borax during polymerization reaction leading to extensive crosslinking of cellulosic chains and generation of mechanically strong composite hydrogels. Dynamic release of from the synthesized composites hydrogels followed Fickian diffusion mechanism and composites with high mechanical strength resulted in slow release of B. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43969.     

Indirect effect of polyvinylpyrrolidone and cetyltrimethylammonium bromide on UV‐blocking efficiency of TiO2@PVP‐CTAB@SiO2 core‐shell nanohybrid particles

In this study, a novel and useful approach to fabricate @PVP‐CTAB@ (TPS) nanohybrid as an effective light stabilizer agent has been reported. Also, the indirect role of the Polyvinylpyrrolidone and cetyltrimethylammonium bromide on UV (ultraviolet) protection properties of nanohybrid particles was investigated. In addition, comparative studies were carried out to evaluate the photocatalytic and UV protection properties of @ (TS), commercial (US3490), synthesized nanparticles, and TPS nanoparticles. Furthermore, the UV protection property of 2‐(2H‐benzotriazol‐2‐yl)?4, 6‐bis (1‐methyl‐1‐phenylethyl) phenol, as an organic anti UV, was also compared with TPS nanoparticles. The as prepared nanohybrid was characterized by Fourier transform infrared spectroscopy, zeta potential, field emission scanning electron microscope (FESEM), transmission electron microscope (TEM), and UV‐Vis spectroscopy. FESEM and TEM micrographs show monodispersity and nano‐metric size of TPS. Rhodamine B degradation study clearly shows that TPS present the lowest photocatalytic property. Also, UV‐Vis spectroscopy results show that the TPS nanoparticles illustrate higher UV blocking ability comparing to other presented anti UV materials. TPS with convenient and useful synthesis method, high UV blocking ability, and little effect on polymer matrix can be introduced as a novel UV‐blocking agent in polyurethane matrix. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44148.