Solid-state nuclear magnetic resonance of the PA6/PC,PA6/PPO,and PA6/PC/PPO blends

The effect of mixing time is very important to plasticization and/or occurrence of chemical reaction between polyamide 6/poly(propylene oxide), polyamide 6/polycarbonate, and polyamide 6/polycarbonate/poly(propylene oxide) blends. The systems were investigated through solid-state carbon-13 cross-polarization magic angle spinning with variable contact time in the NMR experiment. In the systems, polycarbonate can prevent the antiplasticization effect already observed in the polyamide 6/poly(propylene oxide) blend. Therefore, it was verified that the addition of polycarbonate in the polyamide 6/poly(propylene oxide) system causes a hardening of the blend. This fact can be attributed to the restriction of the mobility of the NH group, probably influenced by the type of interaction that occurs in the polyamide 6/polycarbonate/poly(propylene oxide), due to the effect of poly(propylene oxide), which can be act as an interfacial agent promoting a better interaction between polyamide 6 and polycarbonate. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 129–133, 1998     

Effect of in situ synthesized macroactivator on morphology of PA6/PS blends via successive polymerization

In situ polymerization and in situ compatibilization was adopted for preparation of ternary PA6/PS‐g‐PA6/PS blends by means of successive polymerization of styrene, with TMI and ε‐caprolactam, via free radical copolymerization and anionic ring‐opening polymerization, respectively. Copolymer poly(St‐g‐TMI), the chain of which bears isocyanate (? NCO), acts as a macroactivator to initiate PA6 chain growth from the PS chain and graft copolymer of PS‐g‐PA6 and pure PA6 form, simultaneously. The effect of the macroactivator poly(St‐g‐TMI) on the phase morphology was investigated in detail, using scanning electron microscopy. In case of blends with higher content of PS‐g‐PA6 copolymer, copolymer nanoparticles coexisting with the PS formed the matrix, in which PA6 microspheres were dispersed evenly as minor phase. The content of the compositions (homopolystyrene, homopolyamide 6, and PS‐g‐PA6) of the blends were determined by selective solvent extraction technique. The mechanical properties of PA6/PS‐g‐PA6/PS blends were better than that of PA6/PS blends. Especially for the blends T10 with lower PS‐g‐PA6 copolymer content, both the flexural strength and flexural modulus showed significantly improving because of the improved interfacial adhesion between PS and PA6. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Blends of poly(2,6‐dimethyl‐1,4‐phenylene oxide)/polyamide 6 toughened by maleated polystyrene‐based copolymers: Mechanical properties,morphology, and rheology

Poly(2,6‐dimethyl‐1,4‐phenylene oxide)/polyamide 6 (PPO/PA6 30/70) blends were impact modified by addition of three kinds of maleated polystyrene‐based copolymers, i.e., maleated styrene‐ethylene‐butylene‐styrene copolymer (SEBS‐g‐MA), maleated methyl methacrylate‐butadiene‐styrene copolymer (MBS‐g‐MA), and maleated acrylonitrile‐butadiene‐styrene copolymer (ABS‐g‐MA). The mechanical properties, morphology and rheological behavior of the impact modified PPO/PA6 blends were investigated. The selective location of the maleated copolymers in one phase or at interface accounted for the different toughening effects of the maleated copolymer, which is closely related to their molecular structure and composition. SEBS‐g‐MA was uniformly dispersed in PPO phase and greatly toughened PPO/PA6 blends even at low temperature. MBS‐g‐MA particles were mainly dispersed in the PA6 phase and around the PPO phase, resulting in a significant enhancement of the notched Izod impact strength of PPO/PA6 blends from 45 J/m to 281 J/m at the MBS‐g‐MA content of 20 phr. In comparison, the ABS‐g‐MA was mainly dispersed in PA6 phase without much influencing the original mechanical properties of the PPO/PA6 blend. The different molecule structure and selective location of the maleated copolymers in the blends were reflected by the change of rheological behavior as well. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Effect of nylon 6 on fracture behavior and morphology of tough blends of poly(2, 6‐dimethyl‐1,4‐phenylene oxide) and maleated styrene‐ethylene‐butadiene‐styrene block copolymer

Ternary blends of poly(2,6‐dimethyl‐1,4‐phenylene oxide) (PPO), nylon 6, and styrene‐ethylene‐butadiene‐styrene block copolymer grafted with maleic anhydride (SEBS‐g‐MA) were prepared via a melt extrusion, and the fracture behavior, morphology, mechanical properties, and rheology were studied. The compatibilization of the blended components was confirmed by differential scanning calorimetry (DSC) analysis. Mechanical properties evaluation demonstrated that incorporation of nylon 6 resulted in an improvement of the tensile strength, but reduction of both the notched Izod impact strength and elongation at break. Transmission electron microscopy (TEM) observation revealed that the network structure of SEBS‐g‐MA domain was gradually destroyed by incorporating the nylon 6. A conversion of SEBS‐g‐MA domain from the network to the irregular dispersed phase took place when the nylon 6 content reached 20 wt %, which resulted in a reduction of the impact strength. Fracture morphology implied that increase of the tensile strength was caused by the plastic deformation of matrix. Rheology investigation indicated that the melt viscosities could be reduced significantly with increasing the content of nylon 6; thus, the processability was improved. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99:3336–3343, 2006     

High‐frequency welding of thermoplastic LLDPE/PA 6/PE‐g‐MAH ternary blends

High frequency (HF) welding of linear low density polyethylene (LLDPE) melt blends with polyamide 6 (PA6) was done at 27.12 MHz using maleic anhydride grafted polyethylene (PE‐g‐MAH) as compatibilizer. HF welding was not possible for the blends at room temperature, but possible at higher temperatures (50, 80°C) although the maximum relaxation frequency was lower than the operating frequency. Greater dielectric constant, dissipation factor, and welding performance were obtained when PA 6 was premixed with PE‐g‐MAH rather than the one‐shot process where all the components were mixed simultaneously. This was interpreted in terms of lowered viscosity of PA 6 phase, which encapsulates the flow effectively and provides great skin effect. Also, the peeling force of resin–resin was greater than resin–nylon mesh due to the higher melting temperature and vacancy of nylon mesh. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Morphology,thermal behavior,and mechanical properties of PA6/UHMWPE blends with HDPE‐g‐MAH as a compatibilizing agent

A functionalized high‐density polyethylene (HDPE) with maleic anhydride (MAH) was prepared using a reactive extruding method. This copolymer was used as a compatibilizer of blends of polyamide 6 (PA6) and ultrahigh molecular weight polyethylene (UHMWPE). Morphologies were examined by a scanning electron microscope. It was found that the dimension of UHMWPE and HDPE domains in the PA6 matrix decreased dramatically, compared with that of the uncompatibilized blending system. The size of the UHMWPE domains was reduced from 35 μm (PA6/UHMWPE, 80/20) to less than 4 μm (PA6/UHMWPE/HDPE‐g‐MAH, 80/20/20). The tensile strength and Izod impact strength of PA6/UHMWPE/HDPE‐g‐MAH (80/20/20) were 1.5 and 1.6 times as high as those of PA6/UHMWPE (80/20), respectively. This behavior could be attributed to chemical reactions between the anhydride groups of HDPE‐g‐MAH and the terminal amino groups of PA6 in PA6/UHMWPE/HDPE‐g‐MAH blends. Thermal analysis was performed to confirm that the above chemical reactions took place during the blending process. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 232–238, 2000     

Studies on mechanical and morphological behavior of hybrid nanoclay‐reinforced EPDM‐g‐TMEVS/PS blends

A new copolymer of tris(2‐methoxyethoxy) vinylsilane (TMEVS)‐grafted ethylene–propylene–diene elastomer (EPDM‐g‐TMEVS) has been developed by grafting of TMEVS onto EPDM by using dicumylperoxide (DCP) initiator. The linear polystyrene blends (EPDM‐g‐TMEVS/PS) based on EPDM‐g‐TMEVS have been synthesized with varying weight percentages of polystyrene in a twin‐screw extruder. In a similar manner, the dynamically vulcanized and nanoclay‐reinforced polystyrene blends have also been developed using DCP and organically modified montmorillonite clay separately by means of a twin‐screw extruder. The grafting of TMEVS onto EPDM at allylic position present in the third monomer of EPDM has been confirmed by Fourier Transform infrared spectroscopy. The effect of silane‐grafted EPDM and concentration of nanoclay on mechanical properties of polystyrene blends has been studied as per ASTM standards. The morphological behavior of these blends has been investigated using scanning electron microscope. It was observed that the incorporation of silane‐grafted EPDM enhanced the impact strength and the percentage elongation of linear‐ and dynamically vulcanized blends. However, the values of tensile strength, flexural strength, flexural modulus, and hardness of the blends were found to be decreasing with the increase of silane‐grafted EPDM. In the case of nanoclay‐reinforced polystyrene blends, the values of impact strength, tensile strength, flexural strength, flexural modulus, and hardness were increased with an increase in the concentration of nanoclay. XRD studies have been carried out to confirm the formation of nanoclay‐reinforced EPDM‐g‐TMEVS/PS blends. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Mechanical and thermal properties of toughened PA6/HDPE/SEBS‐g‐MA/Clay nanocomposite

Preparation and morphology of Polyamide 6 (PA6)/high density polyethylene (HDPE)/Styrene/Ethylene–Butylene/Styrene grafted with maleic anhydride (SEBS‐g‐MA)/Modified clay nanocomposites were studied. Mixing was performed using melting process in an extruder co‐rotating twin screw. After etching the materials with boiling toluene and THF at room temperature, the morphology of sample checked by scanning electron microscopy (SEM) analyses. X‐ray diffraction (XRD) used for evaluation of the effects of organo‐clay addition in the structure of nanocomposites. XRD traces showed that the characteristic (001) peak of the nanocomposites shifted to the lower degree region. XRD and SEM results showed more uniformly distribution and dispersion of HDPE in the PA6 matrix. Better sample morphology obtained, regarding less distance, and more uniformity between nanoparticles. The mechanical properties like tensile strength, impact strength, hardness and thermal properties of these toughened nanocomposites are discussed in terms of the nanoclay, SEBS‐g‐MA contents and morphology. Adding nanoclay improved hardness of nanocomposites product but reduced toughness and thermal properties. Meanwhile the presence of SEBS‐g‐MA as a compatibilizer improved toughness, thermal properties, hardness property, and the balance properties are achieved. POLYM. ENG. SCI., 55:29–33, 2015. © 2014 Society of Plastics Engineers     

Reactive compatibilization of PP/PBT blends by a mixture of PP‐g‐MA and epoxy resin

In this study, dual compatibilizers composed of the commercially available maleic anhydride‐grafted polypropylene (PP–MA) and a multifunctional epoxy resin were demonstrated to effectively compatibilize the immiscible and incompatible blends of PP and poly(butylene terephthalate) (PBT). The PP–MA with a low MA content is totally miscible with PP to make the PP phase quasi‐functionalized, so that the multifunctional epoxy has the chance to react with PBT and PP–MA simultaneously to form PP–MA‐co‐epoxy‐co‐PBT copolymers at the interface. These desired copolymers are able to anchor along the interface and serve as efficient compatibilizers. The compatibilized blends, depending on the quantity of dual compatibilizers employed, exhibit higher viscosity, finer phase domain, and improved mechanical properties. Epoxy does not show compatibilization effects for the PP/PBT blends without the presence of PP–MA in the blends. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 79: 2272–2285, 2001     

Effect of functionalized SWCNTs on microstructure of PP‐g‐MA/OMMT/f‐SWCNTs nanocomposite

The aim of this work was to study the effect of functionalized single‐walled carbon nanotubes (f‐SWCNTs) on the microstructure of PP‐g‐MA/organic modified montmorillonite (OMMT)/f‐SWCNTs ternary nanocomposite. Pristine SWCNTs were chemically modified by maleic anhydride to improve the interaction between PP‐g‐MA and nanotubes. The dispersion states of OMMT in the different nanocomposites were investigated by wide angle X‐ray diffraction. The morphologies of the nanocomposites were characterized by scanning electron microscopy. Crystallization behaviors of nanocomposites were studied through differential scanning calorimetry and polarizing optical microscopy. Different than the PP‐g‐MA/OMMT binary nanocomposite, in which the OMMT is mainly in an exfoliated state, the ternary PP‐g‐MA/OMMT/f‐SWCNTs nanocomposite exhibits mostly intercalated OMMT. Furthermore, in the ternary nanocomposite, the crystallization of polymer is mainly induced by f‐SWCNTs rather than by OMMT. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Confined crystallization phenomena in immiscible polymer blends with dispersed micro - and nanometer sized PA6 droplets, part 1: uncompatibilized PS/PA6, (PPE/PS)/PA6 and PPE/PA6 blends

In this paper the crystallization behavior of PA6, dispersed as droplets in various immiscible amorphous polymer matrices, is reported. PA6 was melt-mixed at various compositions with PS, (PPE/PS 50/50 wt/wt) and PPE using twin-screw extrusion. The phase morphologies of the obtained blends were analysed using SEM, etching experiments and image analysis. The crystallization behavior of PA6 was investigated by dynamic and isothermal DSC experiments. In case PA6 is dispersed as droplets, fractionated crystallization behavior occurs, characterized by several crystallization events at different, lowered crystallization temperatures. It is found to depend on the blend morphology (size of the droplets) and the thermal history of the samples (heterogeneous nucleation density). The PA6 droplet size distribution is shown to strongly influence the crystallization behavior of the droplets. Vitrification of the matrix appears to cause nucleation in the droplets at the interface. Decreasing the PA6 droplet size results in slower overall crystallization rates.     

Mechanical,morphological, and thermal properties of nanotalc reinforced PA6/SEBS‐g‐MA composites

Ternary butylene‐styrene‐g‐maleic anhydride (SEBS‐g‐MA) (100/20 w/w) blend with varying content of nanotalc (1, 3, and 5 wt %) were prepared by melt compounding followed by injection molding. Thermal properties were investigated by thermogravimetric analysis (TGA) and the results show that the thermal properties of nanocomposites are slightly improved by the addition of nanotalc content. The morphology of nanocomposites using wide angle X‐ray diffraction (WAXD) and transmission electron microscopy (TEM) revealed the delamination of talc layers in the ternary nanocomposites. The dynamic mechanical properties of the samples were analyzed by using dynamic mechanical thermal analyzer (DMTA). The results show that the storage modulus of the blend monotonically increased while tan δ curve show the diffuse pattern with the nanotalc content. The mechanical properties of PA6/SEBS‐g‐MA nanocomposites were studied by tensile, flexural, and impact tests. The tensile and flexural properties continuously increased while izod impact and elongation‐at‐break decreased with nanotalc content. Various theoretical predictive models were used to correlate tensile modulus with the experimental data. The experimental data shows the positive deviation with the applied models. Bela Pukanszky model has been used to calculate the value of parameter B by employing tensile strength data. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41381.     

Studies on fracture behavior of tough PA6/PP blends

Fracture toughness of injection-molded PA6/PP blends compatibilized with SEBS-g-MA was studied using deeply double-edge notched tension (DDENT) specimens according to the essential work of fracture procedure. The fracture mechanical studies also included tensile impact tests on the DDENT specimens and characterization of the fracture surfaces by electron microscopy. The results were compared with those of traditional tensile tests and Izod impact tests on single-edge notched samples, and the sensibility of the methods was evaluated. Effects of sample position, ligament length, testing direction, and test speed were studied as well. It was found that the essential work of fracture concept, earlier applied to thin sheets, can also be applied to injection-molded tough blends. High deformation of the skin may, however, interfere with the measurements and cause a “tail” in the load-deformation curves. The plastic work of fracture (w_p) was found to correlate with the impact strength, and thus, it described the toughness. The highest values for work of fracture were recorded for the compatibilized blend with a PA6/PP ratio of 80/20. The essential work of fracture (w_e) in turn increased with increasing PA6 content and behaved like tensile strength. The test speed was found to affect the fracture behavior substantially: differences between the materials were more pronounced in high-speed tensile impact tests, which revealed signs of cavitation in addition to large-scale plastic deformation for the tough PA6-rich blend compositions. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 66: 2209–2220, 1997     

Preparation and properties of compatibilized PVC/SMA‐g‐PA6 blends

The morphology and mechanical properties of PVC/SMA‐g‐PA6 blends were investigated in this paper. Graft to polymer SMA‐g‐PA6 was prepared via a solution graft reaction between SMA and PA6. FTIR test evidences the occurrence of the graft reaction between SMA and PA6. DSC analysis shows that SMA‐g‐PA6 has a lower melting point of 187°C, which may result in a decrease in crystallinity of PA6 and thus enable efficient blending of SMA‐g‐PA6 and PVC. Compatibilization was evidenced by the dramatic increase in mechanical properties, the smaller particle size and finer dispersion of PA6 in PVC matrix, and, further, a cocontinuous morphology at 16 wt % SMA‐g‐PA6 content. SMA‐g‐PA6 from the solution graft reaction can toughen and reinforce PVC material. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 432–439, 2004     

Effects of glycerol and PE‐g‐MA on morphology,thermal and tensile properties of LDPE and rice starch blends

The effects of glycerol and polyethylene‐grafted maleic anhydride (PE‐g‐MA) on the morphology, thermal properties, and tensile properties of low‐density polyethylene (LDPE) and rice starch blends were studied by scanning electron microscopy (SEM), differential scanning calorimetry, and the Instron Universal Testing Machine, respectively. Blends of LDPE/rice starch, LDPE/rice starch/glycerol, and LDPE/rice starch/glycerol/PE‐g‐MA with different starch contents were prepared by using a laboratory scale twin‐screw extruder. The distribution of rice starch in LDPE matrix became homogenous after the addition of glycerol. The interfacial adhesion between rice starch and LDPE was improved by the addition of PE‐g‐MA as demonstrated by SEM. The crystallization temperatures of LDPE/rice starch/glycerol blends and LDPE/rice starch/glycerol/PE‐g‐MA blends were similar to that of pure LDPE but higher than that of LDPE/rice starch blends. Both the tensile strength and the elongation at break followed the order of rice starch/LDPE/glycerol/PE‐g‐MA blends > rice starch/LDPE/glycerol > LDPE/rice starch blends. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 344–350, 2004     

Effect of composition and processing conditions on the chemical and morphological evolution of PA‐6/EPM/ EPM‐g‐MA blends in a corotating twin‐screw extruder

This study investigated the effect of blend composition and processing conditions on the chemical conversion and morphological evolution of PA‐6/EPM/EPM‐g‐MA blends along a twin‐screw extruder. The maleic anhydride (MA) content of the modified rubber was found to decrease strongly, to a level of almost zero, and in the melting zone the particle size was dramatically reduced, from millimeters to submicrometers. Blend composition had a secondary effect on both chemical conversion and morphological development. The processing conditions, particularly the temperature profile and the screw speed, affected both the chemical conversion and the morphological evolution. Using low temperatures and low screw rotation it was possible to follow in detail the evolution of morphological development of a reactive blend in a twin‐screw extruder. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 1535–1546, 2001     

PPO-g-MAH与CNTs-x对PPO/PA6共混物的协同增强作用研究

研究了聚苯醚/尼龙6/聚苯醚接枝马来酸酐/功能化碳纳米管(PPO/PA6/PPO-g-MAH/CNTs-x)复合材料的形貌结构、力学性能、动态力学行为、流变性能。引入增容剂PPO-g-MAH可改善PPO与PA6之间的界面性能,明显提高了PPO/PA6共混物的力学性能。通过拉伸、冲击实验,动态力学和流变学实验分析发现,在PPO/PA6/PPO-g-MAH共混物中添加氨基化碳纳米管(CNTs-NH₂),其形貌和力学性能均优于碳纳米管(CNTs)和羧基化碳纳米管(CNTs-COOH)。这是由于CNTs-NH₂与PA6/PPO-g-MAH的相互作用较强,并随着CNTs-NH₂添加量的增加,复合材料的拉伸性能、储能模量和复数黏度提高,但冲击强度降低。     

A study of the effect of PP‐g‐MA and SEBS‐g‐MA on the mechanical and morphological properties of polypropylene/nylon 6 blends

The mechanical and morphological properties of polypropylene/nylon 6 blends compatibilized with PP grafted with maleic anhydride (PP‐g‐MA) and styrene/ethene‐co‐butene/styrene grafted with maleic anhydride (SEBS‐g‐MA) are studied using a special version of a factorial design known as extreme vertices. Properties examined include yield stress, modulus, elongation, toughness, impact strength and morphology. Comparisons are made between various treatment combinations (i.e. a variety of blends) and polypropylene homopolymer using various statistical methods including analysis of variance (ANOVA). Scheffe's Test and Duncan's Multiple Range Test. Significant differences were found for yield stress, modulus, elongation, toughness and impact strength for specific treatment combinations versus PP as well as on average. Ternary diagrams are used to plot response surfaces of the measured data illustrating the main effects and interactions involved, while allowing correlations to be made with blend morphology. Indications from test results and analysis of response surfaces show a strong relationship between nylon/compatibilizer ratio and mechanical properties.     

Compatibilization and elastomer toughening of polyamide‐6 (PA6)/poly(phenylene ether) (PPE) blends

In the elastomer‐modified (polyamide‐6/poly(phenylene ether) (PA6/PPE) = 50/50 blends, poly(styrene‐co‐maleic anhydride) (SMA) was demonstrated to be an efficient reactive compatibilizer. The G1651 elastomer was shown to be an effective impact modifier to result in superior toughness and heat‐deflection temperature (HDT) than is the 1901X elastomer for the SMA‐compatibilized blends because G1651 particles exclusively reside within the dispersed PPE phase but 1901X particles tend to distribute in the PA6 matrix and/or along the interface. The apparent average diameter of the dispersed PPE phase is insignificantly dependent on the elastomer content in the G1651‐modified blend, whereas it increases with increase of the elastomer content in the 1901X‐modified blend. Moreover, there exists a critical elastomer content, 15 phr, for the ductile–brittle transition of the G1651‐modified SMA‐modified PA6/PPE blends. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 23–32, 1999