Synthesis of styrene–maleic anhydride random copolymer and its compatibilization to poly(2,6‐dimethyl‐1,4‐phenylene ether)/brominated epoxy resin

Styrene–maleic anhydride random copolymer (R‐SMA_7.5), with a low content of maleic anhydride (MAH) of about 7.5 mol%, has been prepared, and the copolymer was characterized by fourier‐transform infrared (FTIR) and ¹³C NMR techniques showing that the product contained only random copolymer without blocks. The miscibility between poly(2,6‐dimethyl‐1,4‐phenylene ether) (PPE) and R‐SMA, was investigated by differential scanning calorimetry (DSC), showing that PPE was miscible with R‐SMA synthesized in our laboratory over the entire composition with low MAH content. A blend of R‐SMA₁₈ (MAH content is about 18 mol%) and PPE was also studied by DSC, which showed that PPE was immiscible when R‐SMA was the major component, although it was miscible with limited composition. FTIR investigation showed that R‐SMA could react with bromide epoxy (BEP) resin at high temperature (180°). The heat‐resistance and mechanical properties of R‐SMA/PPE/BEP systems were tested and analyzed, and results indicated that R‐SMA could improve the miscibility of PPE and BEP with increasing T_g of the BEP phase and decreasing the T_g of the PPE slightly, improving the breaking elongation and breaking energy, which resulted from good miscibility between PPE and BEP with R‐SMA as the compatibilizer. Finally, the properties of the composites (copper clad laminate) with R‐SMA_7.5 are studied and discussed. Copyright © 2003 Society of Chemical Industry     

Preparation of well‐defined block copolymer having one polystyrene segment and another poly(styrene‐alt‐maleic anhydride) segment with RAFT polymerization

Block copolymers, polystyrene‐b‐poly(styrene‐co‐maleic anhydride), have been prepared by reversible addition‐fragmentation chain transfer (RAFT) polymerization technique using three different approaches: 1‐phenylethyl phenyldithioacetate (PEPDTA) directly as RAFT agent, mediated polystyrene (PS) block as the macromolecular PS‐RAFT agent and mediated poly(styrene‐maleic anhydride) (SMA) block with alternating sequence as the macromolecular SMA‐RAFT agent. Copolymers synthesized in the one‐step method using PEPDTA as RAFT agent possess one PS block and one SMA block with gradient structure. When the macromolecular RAFT agents are employed, copolymers with one PS block and one alternating SMA block can be produced. However, block copolymers with narrow molecular weight distribution (MWD) can only be obtained using the PS‐RAFT agent. The MWD deviates considerably from the typical RAFT polymerization system when the SMA is used as the RAFT agent. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Polystyrene and polyester polyurethane elastomer blends compatibilized by SMA

Blends of polystyrene (PS) with polyester polyurethane elastomer (PU‐es) were compatibilized by addition of poly(styrene‐co‐maleic anhydride) (SMA) containing 7 wt % of maleic anhydride. Binary nonreactive (PS/PU‐es) blends, binary reactive (SMA/PU‐es) blends, and ternary reactive blends (PS/SMA/PU‐es) were prepared with 10 and 20 wt % of PU‐es. The maleic anhydride content in the ternary reactive blends was varied through addition of different SMA amounts from 0.5 to 5 wt %. Polyurethane in the blends was crosslinked by using dicumyl peroxide or sulfur to improve its mechanical properties. The experimental processing conditions, such as temperature and rotor speed in an internal mixer, were analyzed before blend preparation by processing the individual polymers, PS and SMA, and the PS/PU‐es nonreactive blend (90/10), to prevent the degradation of the polymer during melt mixing and to assure macroscopic homogeneity. The torque behavior during the mixture indicated a grafting copolymerization, which was responsible for the significant drop of the PU‐es domain size in the glassy matrix, as observed by scanning electronic microscopy (SEM). The miscibility of the glassy matrix, which was shown to be dependent on the composition and the phase behavior of ternary blends, became very complex as the SMA concentration increased, as concluded from dynamical–mechanical analysis. Blends containing 20 wt % of PU‐es presented an increase up to a factor of 2 in the deflection at break in relation to PS. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2297–2304, 2004     

Polystyrene and polyether polyurethane elastomer blends compatibilized by SMA: Morphology and mechanical properties

Blends of polystyrene (PS) and the polyether polyurethane elastomer (PU‐et) were prepared by melt mixing using poly(styrene‐co‐maleic anhydride) (SMA) containing 7 wt % of maleic anhydride as a compatibilizer. The polyurethane in the blends was crosslinked using dicumyl peroxide or sulfur. The content of maleic anhydride was varied in the blends through the addition of different SMA amounts. The morphology of the blends was analyzed by SEM and a drastic reduction of both the domain size and its distribution was observed with increase of the anhydride content in the blends. The morphology of the PU‐et blends also showed dependence on the crosslinker agent used for the elastomer, and larger domains were obtained for the elastomer phase crosslinked with dicumyl peroxide. The mechanical properties of the blends were evaluated by flexural and impact strength tests. The blend containing 0.5 wt % of maleic anhydride and 20 wt % of PU‐et crosslinked with sulfur showed the highest strength impact, which was three times superior to the PS strength impact, and the blends containing 20 wt % of PU‐et crosslinked with dicumyl peroxide showed the highest deflection at break independent of the anhydride content. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 830–837, 2002     

In situ compatibilization of polystyrene and polyurethane blends by using poly(styrene-co-maleic anhydride) as reactive compatibilizer

Blends of polystyrene (PS) and polyurethane (PU) elastomer were obtained by melt mixing, using poly(styrene-co-maleic anhydride) (SMA) containing 7 wt % of maleic anhydride groups as a reactive compatibilizer. Polyurethanes containing polyester flexible segments, PU-es, and polyether flexible segments, PU-et, were used. These polyurethanes were crosslinked with dicumyl peroxide or sulfur to improve their mechanical properties. The anhydride groups of SMA can react with the PU groups and form an in situ graft copolymer at the interface of the blends during their preparation. The rheological behavior was accompanied by torque versus time curves and an increase in the torque during the melt mixing was observed for all the reactive blends, indicating the occurrence of a reaction. Solubility tests, gel permeation chromatography, and scanning electronic microscopy confirmed the formation of a graft copolymer generated in situ during the melt blending. These results also indicate that this graft copolymer contains C C bond between SMA and PU chains. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 2514–2524, 2001     

Hole structure and its formation in thin films of hydrolyzed poly(styrene maleic anhydride) alternating copolymers

Maleic anhydride moieties on the backbone chains of poly(styrene maleic anhydride) alternating copolymer (SMA) hydrolyzed in a THF solution containing water and hydrochloric acid. Well‐arrayed holes were obtained in spin‐cast thin hydrolyzed SMA films on a single crystal silicon wafer, and the hole diameter and its distribution were measured with AFM data. Results showed that the hole size was almost uniform, and was influenced by water content when spin speed was kept unchanged. The THF solution with a SMA concentration of about 1 g/mL and weight ratio H₂O/SMA of 1/3 produced holes having an average diameter of 0.60 μm and depth of 206.12 nm, when cast at a spin speed of 1400 rpm. It was noted that the formation of the holes in thin hydrolyzed SMA film was different from the dewetting process in thin homopolymer films, but was associated with the intrinsic properties of the copolymer forming the films. The surfactant effect of hydrolyzed SMA was suggested to interpret the formation of the holes. The holes were described to be the traces of water droplets that were emulsified by the hydrolyzed SMA during casting. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 267–274, 2000     

Effect of polyurethane molecular weight on the properties of polyurethane–poly(butyl methacrylate) hybrid latex prepared by miniemulsion polymerization

Polyurethane (PU) prepolymer was first prepared via introducing double bonds on‐to the PU chains, and then polyurethane–poly (butyl methacrylate) (PU–PBMA) hybrid latex was prepared via miniemulsion polymerization. Transmission electron microscopy, Differential scanning calorimeter (DSC), Fourier transform infrared, and dynamic mechanical analysis were adopted to characterize the hybrid latex and its coating film. Both the coating property and the miscibility of PU–PBMA emulsion have been greatly improved through introducing double bonds into PU prepolymer. With an increase in the molecule weight of PU (M_PU), the increase in the particle size of PU–PBMA emulsion was observed plus decreases in the stability of the hybrid latex and conversion of methacrylate. Besides, as M_PU increased, the final dried coating film of the hybrid latex showed decreased water resistance, weakened miscibility, and improved mechanical properties. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Variations of the glass‐transition temperature in the imidization of poly(styrene‐co‐maleic anhydride)

The imidization of poly(styrene‐co‐maleic anhydride) (SMA) was conducted, and the glass‐transition temperatures (T_g's) of the resulting products were measured with differential scanning calorimetry. The contributions from functional groups of maleic anhydride, N‐phenylmaleamic acid, and N‐phenylmaleimide to T_g were examined. T_g increased in the order of SMA < styrene–N‐phenyl maleimide copolymer < styrene–N‐phenyl maleamic acid copolymer and followed the Fox equation. T_g of the imidized products of SMA could be controlled by the conversions of both ring‐opening and ring‐closing reactions. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 2418–2422, 2007     

New polymers from plant oil derivatives and styrene‐maleic anhydride copolymers

In this study, styrene maleic anhydride copolymer (SMA2000, Styrene : Maleic Anhydride 2 : 1) is grafted and/or crosslinked with epoxidized methyl oleate, epoxidized soybean oil, methyl ricinoleate (MR), castor oil (CO), and soybean oil diglyceride. Base catalyzed epoxy‐anhydride and alcohol‐anhydride polyesters were synthesized by using the anhydride on SMA, the epoxy or secondary alcohol groups on the triglyceride based monomers. The characterizations of the products were done by DMA, TGA, and IR spectroscopy. SMA‐epoxidized soy oil and SMA‐CO polymers are crosslinked rigid infusible polymers. SMA‐epoxidized soy oil and SMA‐CO showed T_g's at 70 and 66°C, respectively. Dynamic moduli of the two polymers were 11.73 and 3.34 Mpa respectively. SMA‐epoxidized methyl oleate, poly[styrene‐co‐(maleic anhydride)]‐graft‐(methyl ricinoleate), and SMA‐soy oil diglyceride polymers were soluble and thermoplastic polymers and were characterized by TGA, GPC, DSC, NMR, and IR spectroscopy. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Syntheses and properties of polyurethanes containing side‐chain azobenzene groups

Polymers containing azobenzene groups have the characteristic reaction of photo‐induced cis–trans isomerism. The study of new materials for optical information storage has prompted making use of these photo‐isomerizations. In this study, we report the syntheses and properties of four different polyurethanes (DR‐PUns) containing azobenzene groups in the side‐chains. The structurally similar polyurethanes (DR‐PUns) were synthesized by the polycondensation reaction of Disperse Red 19 (DR 19) and four different diisocyanates in dimethylformamide. By introducing of DR 19 into the polymer, we obtained polymers containing a photochromic group in the side‐chain. The weight‐average molecular weights of the DR‐PUns were in the range 5500–12 900. The T_gs of the DR‐PUns range from 119.5 °C to 157.0 °C, depending on the structure of the diisocyanate. Optical properties and solubilities of the polyurethanes were compared. The diffraction efficiencies of films were measured as a function of the reaction time. Typically, the diffraction efficiencies of the DR‐PU1 film prepared from toluene 2,4‐diisocyanate were observed up to a level of 0.25%. For the DR‐PU1 film, the effect of the intensity of the induced laser beam on the diffraction efficiency is also discussed. © 2003 Society of Chemical Industry     

Phase morphology and interfacial characteristics of polycarbonate/acrylonitrile‐ethylene‐propylene‐diene‐styrene blends compatibilized by styrene‐maleic anhydride copolymers

Blends of polycarbonate (PC) and acrylonitrile ‐ ethylene‐propylene‐diene‐styrene (AES) were reactive compatibilized by styrene‐maleic anhydride copolymers (SMA). The changes in phase morphology and interfacial characteristics of the blends as a function of maleic anhydride content of SMA and the concentration of compatibilizer have been systematic studied. The occurrence of reaction between the terminal hydroxyl groups of PC and the maleic anhydride (MA) of compatibilizer was confirmed by fourier transform infrared (FTIR) spectroscopy. A glass transition temperature (T_g) with an intermediate value between T_g(AES) and T_g(PC) was found on differential scanning calorimeter (DSC) curves of PC/AES blends compatibilized with SMA contains high levels of MA. Furthermore, at lower compatibilizer content, increase of the compatibilizer level in blends result in decreasing gap between two T_gs corresponding to the constituent polymers. Small angle X‐ray scattering (SAXS) test results indicated that compatibilizer concentration for the minimum of blend interface layer's thickness was exactly the same as it was when compatibilized PC/AES blend exhibited optimal compatibility in DSC test. The observed morphological changes were consistent well with the DSC and SAXS test results. A new mechanism of interfacial structural development was proposed to explain unusual phenomena of SMA compatibilized PC/AES blends. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42103.     

Preparation and characterization of polyurethane microcapsules containing n‐octadecane with styrene‐maleic anhydride as a surfactant by interfacial polycondensation

A series of polyurethane microcapsules containing a phase change material (PCM) of n‐octadecane was successfully synthesized by an interfacial polymerization in aqueous styrene‐maleic anhydride (SMA) dispersion with diethylene triamine (DETA) as a chain extender reacting with toluene‐2,4‐diisocyanate (TDI). The average diameter of microPCMs is in the range of 5–10 μm under the stirring speed of 3000–4000 rpm. Optical and SEM morphologies of microPCMs had ensured that the shell was regularly fabricated with the influence of SMA. FTIR results confirmed that the shell material was polyurethane and the SMA chains associated on core material reacted with TDI forming a part of shell material. The shell thickness was decreasing in the range of 0.31–0.55 μm with the molar ratio of DETA/TDI from 0.84 to 1.35 and the weight of core material increasing from 40 to 80% (wt %). By controlling the weight ratio of PCM as 40, 50, 60, 70, and 80% in microPCMs, it was found using DSC that the T_m and T_c of microPCMs were in the range of 29.8–31.0^oC and 21.1–22.0°C and an obvious phase change had been achieved nearly the same temperature range of that of PCM. The results from release curves of microPCM samples prepared by 1.4, 1.7, and 2.0 g of SMA indicated the release properties were affected by the amount of the dispersant, which attributed to the emulsion effect and shell polymerization structure. The above results suggest that the shell structure of microPCMs can be controlled and the properties of microPCMs determined by shell will perform proper practical usage. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4996–5006, 2006     

Synthesis and characterization of alkali‐modified styrene‐maleic anhydride copolymer for dispersion of TiO2

A copolymer of styrene and maleic anhydride was synthesized by free radical polymerization at 80°C using N,N‐dimethylformamide (DMF) as solvent and benzoylperoxide as initiator. The monomer feed ratio of styrene to maleic anhydride was varied in the range of 1 : 1 : to 3 : 1. The polymer yield was found to decrease with increase in styrene in the feed. The molecular weight of copolymers which were formed by taking styrene to maleic anhydride ratio of 1 : 1, 2 : 1, and 3 : 1, as determined by Ostwald Viscometery were about 1862, 2015, and 2276 respectively. The acid values of abovementioned three copolymers were found to be 480, 357, and 295, respectively. The typical viscosity values of 20% solids in ammonical solution of copolymers formed by taking feed ratios of Sty : MAn as 1 : 1 and 2 : 1 were 26 and 136 cp, respectively. For the feed ratio 3 : 1, a gel was formed. The synthesized copolymers were hydrolyzed by alkalis, namely, NaOH, KOH, and NH₄OH. The dispersing ability of hydrolyzed styrene‐maleic anhydride (SMA) copolymers for dispersion of titanium dioxide was studied. The modified SMA copolymers were found to be effective dispersants for TiO₂. Among the three alkalis studied, the Sodium salts of SMA were found to give better dispersion. The copolymer having a 1 : 1 feed ratio showed the best dispersing ability for TiO₂ particles among the three ratios studied. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3194–3205, 2007     

Preparation and self‐assembly of poly(diglycidyl maleate‐co‐stearyl methacrylate)

Poly(diglycidyl maleate‐co‐stearyl methacrylate) (P(DGMA‐co‐SMA)) with reactive epoxy groups was synthesized by reaction of poly(maleic anhydride‐co‐stearyl methacrylate) (P(MA‐co‐SMA)) and epichlorohydrin. The effect of precipitant on self‐assembly behaviors of the resultant copolymer was investigated. It was found that vesicles and nanotubule liked aggregates can be obtained through self‐assembly of P(DGMA‐co‐SMA) in THF solution using CH₃CH₂OH (EtOH) as precipitant while spheral aggregates can be obtained using H₂O as precipitant. The mechanism of the self‐assembly behavior was discussed. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Polymer blends with modified coupling agent. II. Effects of LICA 44 grafted styrene–maleic anhydride copolymer on properties of flame retardant acrylonitrile–butadiene–styrene blends

Flame retardant acrylonitrile–butadiene–styrene (FR‐ABS) blends were prepared by blending tetrabromobisphenol A (TBBA) and antimony trioxide (Sb₂O₃) into the ABS resin. LICA 44 grafted styrene–maleic anhydride (SMA‐g‐L44) copolymers were used as high molecular weight (MW) coupling agents to modify the properties of the FR‐ABS blends, and the copolymers with different LICA 44 grafting ratios were produced via the in vivo and the in situ reactions, respectively. The LICA 44 percentage and the MW of the SMA‐g‐L44 copolymers are important factors influencing the effects of the high MW coupling agent. The impact strength and the tensile yield stress of SMA‐g‐L44 modified FR‐ABS blends increased obviously. The elongation at break and the limiting oxygen index of which also showed an increasing trend after the modification. The coupling effect of SMA‐g‐L44 became weaker at a higher grafting ratio. SEM observation showed that the interfacial boundary in the FR‐ABS became fuzzy after using the SMA‐g‐L44 copolymers. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 865–874, 1999     

Insights in the molecular structure of low- and high-molecular weight poly(styrene-maleic anhydride) from vibrational and resonance spectroscopy

Poly(styrene-maleic anhydride) or SMA are versatile copolymers available in different grades of molecular weight (M_w = 5500–170,000 g/mol) and molar percentage of maleic anhydride (22–50 mol-%). As specific grades can be used for the synthesis of nanoscale structures in paper industry, a better understanding of the molecular structure was needed. Therefore, a broad range of SMA grades was analyzed by means of size exclusion chromatography, infrared spectroscopy, Raman spectroscopy and nuclear magnetic resonance spectroscopy. While the nominal composition could be determined by ¹H NMR and Raman spectroscopy, the combination with ¹³C NMR and FTIR allowed a more detailed characterization of the molecular structure. The high-molecular weight SMA grades show a heterogeneous molecular structure with segments including high styrene and maleic anhydride moieties, respectively. The formation of film patterns was evaluated by deposition from an acetone solution, resulting in homogeneous films, fibrous structures, or spherical shapes with decreasing diameter as a function of maleic anhydride content including primary particle sizes of 100 nm. This study illustrates intrinsic molecular features of SMA grades that are capable for self-assembly, and can provide a selection tool for future nanoparticle formulation.     

Liquid crystallization of poly(styrene‐co‐maleic anhydride) induced by intermolecular hydrogen bonds

The liquid crystallization of general polymer (GP) with maleic anhydride in the main chain has been realized through molecular recognition and self‐assembly based on intermolecular hydrogen bonds. Poly[styrene‐co‐(N‐4‐carboxylphenyl)maleimide] (SMIBA) was synthesized by imidization and dehydration of Poly(styrene‐co‐maleic anhydride) (SMA) with p‐aminobenzoic acid (ABA) for use as an H‐bonded donor polymer. 4‐Methoxy‐4′‐stilbazole (MSZ) and 4‐nitro‐4′‐stilbazole (SZNO₂) were prepared as an H‐bonded acceptor. SMIBA was complexed with MSZ or SZNO₂ by slow evaporation from pyridine solution to form a self‐assembly, which exhibits the mesophase, while neither of the individual components is mesogenic. The phase diagrams of a variety of mixtures between of SMIBA and stilbazoles have been established using DSC and POM. They show complete miscibility and high thermal stability of the liquid crystalline phase over the whole composition range. The tuning of liquid crystalline properties was achieved by changing the composition of the mixture and involving it with a mixture of SZNO₂ and MSZ. IR measurements strongly support the existence of an H‐bonded complex between the carboxylic acid of SMIBA and the pyridine group of stibazoles. Unlike conventional side‐chain liquid crystalline polymer (SLCP), supramolecular SLCP with a lower molecular weigh polymeric donor has higher thermal stability of the liquid crystalline phase due to the microphase separated in the hydrogen bonding case. Liquid crystallization of GP, such as SMA, induced by hydrogen bonds, offers a new route to prepare functional material with controlled molecular architecture from readily accessible and simpler precursors. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 97–105, 1999     

Core‐shell latex synthesized by emulsion polymerization using an alkali‐soluble resin as sole surfactant

A series of alkali‐soluble resins were prepared from esterification reaction of styrene‐maleic anhydride copolymer (SMA) and four fatty alcohols having different alkyl chains. The critical aggregates concentration of the prepared hemiester was lower than SMA, indicating that modification of SMA resin with long alkyl chains could improve their emulsification efficiency. The detailed experiments of emulsion polymerization of methyl methacrylate and butyl acrylate using these hemiesters as sole surfactants showed that SMA‐C12‐75, SMA‐C14‐70, and SMA‐C16‐65 were good surfactants. In the end, we successfully prepared stable latexes using above three good surfactants with relatively low surfactant concentration and high solid content. Characterization of latexes by Zetasizer and transmission electron microscopy revealed that particles of these latexes have core‐shell nanostructure with average particle size below 60 nm. Compared with SMA, the improvement of emulsification efficiency of its hemiesters may come from the better hydrophilic‐lipophilic balance and steric stabilization after incorporation of long alkyl chain. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Synthesis,properties, and dyeing application of nonionic waterborne polyurethanes with different chain length of ethyldiamines as the chain extender

This study deals with the synthesis of some nonionic waterborne polyurethanes (PUs), using ethyldiamines of different chain length, such as ethylenediamine (EDA) and diethyltriamine (DETA), as the chain extender in the reaction, and examines the thermal properties, mechanical properties, and dyeing properties of the PU products and their blends. As far as each PU by itself is concerned, we found that the T_g of the one made with DETA is the highest, followed by that with EDA, and the one with 1,4‐butanediol (1,4‐BD) is the lowest. The PU made with 1,4‐BD as the chain extender has no T_m, while the two others, using diamines as chain extenders, have a clear T_m, the one with DETA being higher than that with EDA. However, the enthalpy data are just the opposite. The tensile strengths of the two PUs, made with diamines as the chain extender, are larger than that made with 1,4‐BD, but their respective elongation properties are just the opposite. A comparison within PUs made with diamines showed that the one made with EDA is greater in both strength and elongation categories than that made with DETA. However, the one made with DETA is far superior to both of those made with 1,4‐BD and EDA in their dye‐exhaustion ratio, color yield (K/S), fixation rate, and color fastness. In respect to the various PU mixtures that we examined, we found that both PUs synthesized with EDA or DETA as the chain extender would have their T_g's greatly increased by blending in some PU made using 1,4‐BD as the chain extender. Among them, in particular, a blend of PU, made separately with DETA and 1, 4‐BD as the chain extender, showed great improvements in both tensile strength and elongation and also demonstrated better dyeability. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2824–2833, 2003     

Functional polymers for colloidal applications. XIV. Syntheses of styrene–maleic anhydride copolymers with different charges and their ability to disperse kaolinite particles

Four kinds of styrene/maleic–anhydride (SMA) copolymer‐derived dispersants with different charged forms were synthesized and characterized with ¹H‐NMR. These four different dispersants contained carboxylic acid groups and exhibited characteristics indicative of anionic, cationic, zwitterionic, or nonionic surfactants as pH was changed. The charge properties of these copolymers changes with pH, and their ability to disperse clay particles under low and high pH were assessed by measuring viscosity or sedimentation, as well as Scanning Electron Microscopy (SEM). The results showed that the dispersing abilities are functions of pH of the system. It was found that SMA‐N [Poly(styrene‐co‐β‐N,N‐dimethylpropylamino) maleic acid, sodium salt)] exhibits the best dispersing ability, the fastest rate of sedimentation, and the smallest sedimentation volume at pH = 2, and SMA‐Na [poly(styrene‐co‐maleic acid, disodium salt)] exhibits the better dispersing ability at pH = 7 and 12. In addition, the aggregation behavior of the dispersants characterized by fluorescence spectroscopy revealed that the degree of aggregation for all dispersants at high concentration increases in the order: SMA‐Na < SMA‐B [poly(styrene‐co‐B‐imino‐propyl‐N‐trimethylammonium acetate) maleic acid, disodium salt)] < SMA‐N < SMA‐Q [poly(styrene‐co‐β‐imino‐propyl‐N‐trimethylammonium sulfate) maleic acid, sodium salt)]. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 592–602, 2000