Recycling of blends of acrylonitrile–butadiene–styrene (ABS) and polyamide

The aim of this work is to evaluate routes to upgrade recycled engineering plastics, especially mixed plastics with acrylonitrile–butadiene–styrene copolymers (ABS) as the major component. A core‐shell impact modifier was successfully used to improve the impact strength of blends of ABS and ABS/polycarbonate (PC) blends recycled from the automotive industry. However, the presence of other immiscible components like polyamide (PA), even in small amounts, can lead to a deterioration in the overall properties of the blends. A styrene–maleic anhydride (SMA) copolymer and other commercial polymer blends were used to promote the compatibilization of ABS and PA. The core‐shell impact modifier was again found to be an efficient additive with regard to the impact strength of the compatibilized ABS/PA blends. The results obtained with fresh material blends were quite promising. However, in blends of recycled ABS and glass‐fiber‐reinforced PA, the impact strength did not exhibit the desired behavior. The presence of poorly bonded glass fibers in the blend matrix was the probable reason for the poor impact strength compared with that of a blend of recycled ABS and mineral‐filled PA. Although functionalized triblock rubbers (SEBS–MA) can substantially enhance the impact strength of PA, they did not improve the impact strength of ABS/PA blends because the miscibility with ABS is poor. The possibilities of using commercial polymer blends to compatibilize otherwise incompatible polymer mixtures were also explored giving promising results. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2535–2543, 2002     

Blends of bisphenol A polycarbonate and rubber‐toughened styrene–maleic anhydride copolymers

The morphology and mechanical properties of polycarbonate (PC) blends with rubber‐toughened styrene–maleic anhydride copolymer materials (TSMA) were investigated and compared with the properties of blends of PC with acrylonitrile–butadiene–styrene (ABS) materials. The PC/TSMA blends showed similar composition dependence of properties as the comparable PC/ABS blends. Polycarbonate blends with TSMA exhibited higher notched Izod impact toughness than pure PC under sharp‐notched conditions but the improvements are somewhat less than observed for similar blends with ABS. Since PC is known for its impact toughness except under sharp‐notched conditions, this represents a significant advantage of the rubber‐modified blends. PC blends with styrene–maleic anhydride copolymer (SMA) were compared to those with a styrene–acrylonitrile copolymer (SAN). The trends in blend morphology and mechanical properties were found to be qualitatively similar for the two types of copolymers. PC/SMA blends are nearly transparent or slightly pearlescent. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1508–1515, 1999     

Blends of recycled polycarbonate and acrylonitrile–butadiene–styrene: comparing the effect of reactive compatibilizers on mechanical and morphological properties

Blends of recycled polycarbonate (PC) and acrylonitrile–butadiene–styrene (ABS) were prepared and some mechanical and morphological properties were investigated. To compatibilize these blends, ABS‐g‐(maleic anhydride) (ABS‐g‐MA) and (ethylene–vinyl acetate)‐g‐(maleic anhydride) (EVA‐g‐MA) with similar degree of grafting of 1.5% were used. To compare the effect of the type of compatibilizer on mechanical properties, blends were prepared using 3, 5 and 10 phr of each compatibilizer. A co‐rotating twin‐screw extruder was used for blending. The results showed that ABS‐g‐MA had no significant effect on the tensile strength of the blends while EVA‐g‐MA decreased the tensile strength, the maximum decrease being about 9.6% when using 10 phr of this compatibilizer. The results of notched Charpy impact strength tests showed that EVA‐g‐MA increased the impact strength of blends more than ABS‐g‐MA. The maximum value of this increase occurred when using 5 phr of each compatibilizer, it being about 54% for ABS‐g‐MA and 165% for EVA‐g‐MA. Scanning electron microscopy micrographs showed that the particle size of the dispersed phase was decreased in the continuous phase of PC by using the compatibilizers. Moreover, a blend without compatibilizer showed brittle behaviour while the blends containing compatibilizer showed ductile behaviour in fracture. © 2013 Society of Chemical Industry     

Mechanical properties of blends of polycarbonate with unmodified and maleic anhydride grafted ABS

Blends of polycarbonate/acrylonitrile–butadiene–styrene terpolymer (PC/ABS) and polycarbonate/maleic anhydride grafted ABS (PC/MABS) were prepared over the whole range of compositions using a single-screw extruder. Tensile, flexural, notched Izod impact properties, and the heat deflection temperature of these blends were determined. Mechanical properties of PC/MABS blends are nearly equal to or higher than, those predicted by the rule of mixtures, whilst those of PC/ABS blends show nearly equal, or negative deviation, from the rule of mixtures. The notched impact strength of PC/MABS blends shows a positive blending effect and proportionate increase from 25wt% PC to 75wt% PC. Scanning electron micrographs were taken of etched surfaces of selective blends. © 1998 SCI.     

Weld line characteristics of PC/ABS blend. II. Effect of reactive compatibilizer

The effects of reactive compatibilizer and processing temperature on the morphology and the mechanical properties at the weld line of 60/40 (wt/wt) poly- carbonate (PC) and acrylonitrile-butadiene-styrene (ABS) copolymer blends were investigated. Amine functionalized styrene/n-phenyl maleimide/maleic anhydride terpolymer (amine-SPMIMA) was used as the in-situ reactive compatibilizer for PC/ABS blend. Weld tensile strength increased as the content of amine-SPMIMA was increased. Weld impact strength showed maximum value for the blend containing about 3% amine-SPMIMA. The variation in the mechanical property at the weld line was correlated with the change in the morphology of the blend. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

The impact of polymer matrix blends on thermal and mechanical properties of boron nitride composites

To improve mechanical and thermal properties of a hexagonal boron nitride platelet filled polymer composites, maleic anhydride was studied as a coupling agent and compatibilizer. Injection molded blends of acrylonitrile butadiene styrene (ABS), high-density polyethylene (HDPE), and maleic anhydride with boron nitride filler were tested for thermal conductivity and impact strength to determine whether adding maleic anhydride improved interfacial interactions between matrix and filler and between the polymers. Adding both HDPE and maleic anhydride to ABS as the matrix of the composite resulted in a 40% improvement in impact strength without a decrease in thermal conductivity when compared to an ABS matrix. The best combination of thermal conductivity and impact strength was using pure HDPE as the matrix material. The effective medium theory model is used to help explain how strong filler alignment helps achieve high thermal conductivity, greater than 5 W/m K for 60 wt % boron nitride. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 137, 48661.     

The effect of graft copolymers of maleic anhydride and epoxy resin on the mechanical properties and morphology of PP/ABS blends

In this work, maleic anhydride‐grafted polypropylene (PP‐g‐MAH) and maleic anhydride‐grafted poly(acrylonitrile‐butadiene‐styrene) (ABS‐g‐MAH) at 2 : 1 mass ratio were added as a compatibilizer in the PP/ABS blends. The compatibilizing effect was evaluated by adding the graft copolymers together with epoxy resin/imidazole curing agent (E51/2E4MZ). The reaction in reactive extrusion, morphological structure, and properties of PP and ABS blends were investigated by using infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and X‐ray spectrum, transmission electron microscope (TEM), dynamic thermomechanical analysis (DMA), differential scanning calorimetry (DSC), and mechanical properties tests. The results showed that the compatibilizing effect was greatly improved because of the addition of the graft copolymers together with epoxy resin/imidazole curing agent (E51/2E4MZ) because the link structure of PP‐g‐MAH and ABS‐g‐MAH was formed by the reaction of anhydride group with epoxy group catalyzed by the imidazole. The size of the dispersed phase decreased dramatically, the interfacial adhesion between ABS particles and PP matrix was improved, and the tensile strength and flexural modulus of the PP/ABS blends increased further. The optimizing properties were obtained at 3 phr E51/2E4MZ. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40898.     

Preparation of the anhydride terminated polycarbonate and its reactive compatibilization with polystyrene

Polycarbonate with anhydride end groups (PC‐anh) was prepared by the reaction between polycarbonate having hydroxyl end groups (PC‐OH) and trimellitic anhydride chloride (TMAC). Hydroxyl or anhydride terminated polycarbonates were characterized by Fourier transform infrared spectroscopy (FTIR) and nuclear magnetic resonance (NMR) spectroscopy. The reaction of PC‐anh with polystyrene containing oxazoline reactive groups (RPS) was confirmed not only by the torque measurement during melt blending of these two but also by FTIR spectroscopy of the reactive blend obtained. Polycarbonate (PC) / polystyrene (PS) compatibilized blends were prepared by melt blending along with their reactive counterparts, PC‐anh and RPS in the Haake mixer. The morphologies of these blends were examined by the scanning electron microscope (SEM). The compatibilized blends with reactive components showed relatively finer morphologies than the uncompatibilized blend without reactive components. Izod impact strength and rheological property of these blends were also investigated. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 1338–1347, 2000     

Effects of ABS‐g‐MAH on mechanical properties and compatibility of ABS/PC alloy

The effects of a compatibilizer, namely, an acrylonitrile–butadiene–styrene copolymer (ABS) grafted with maleic anhydrade (MAH) (ABS‐g‐MAH), on the mechanical properties and morphology of an ABS/polycarbonate (PC) alloy were studied The results showed that a small quantity of ABS‐g‐MAH has a very good influence on the notched Izod impact strength of the ABS/PC alloy without compromising other properties such as the tensile strength, flexural strength, and Vicat softening temperature (VST). The impact strength of the ABS/PC alloy, to a great extent, depends on the loading of ABS‐g‐MAH and the degree of grafting (DG) of MAH in the ABS‐g‐MAH. DSC analysis and SEM observation confirmed that ABS‐g‐MAH could significantly improve the compatibility of the ABS/PC alloy. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 831–836, 2001     

Melt processing,mechanical, and fatigue crack propagation properties of reactively compatibilized blends of polyamide 6 and acrylonitrile–butadiene–styrene copolymer

Within a IUPAC study, melt processing, mechanical, and fatigue crack growth properties of blends of polyamide 6 (PA 6) and poly(acrylonitrile–butadiene–styrene) (ABS) were investigated. We focused on the influence of reactive compatibilization on blend properties using a styrene–acrylonitrile–maleic anhydride random terpolymer (SANMA). Two series of PA 6/ABS blends with 30 wt % PA 6 and 70 wt % PA 6, respectively, were prepared with varying amounts of SANMA. Our experiments revealed that the morphology of the matrix (PA 6 or ABS) strongly affects the blend properties. The viscosity of PA 6/ABS blends monotonically increases with SANMA concentration because of the formation of high‐molecular weight graft copolymers. The extrudate swell of the blends was much larger than that of neat PA 6 and ABS and decreased with increasing SANMA concentrations at a constant extrusion pressure. This observation can be explained by the effect of the capillary number. The fracture resistance of these blends, including specific work to break and impact strength, is lower than that of PA 6 or ABS alone, but increases with SANMA concentration. This effect is most strongly pronounced for blends with 70 wt % PA 6. Fatigue crack growth experiments showed that the addition of 1–2 wt % SANMA enhances the resistance against crack propagation for ABS‐based blends. The correlation between blend composition, morphology and processing/end‐use properties of reactively compatibilized PA 6/ABS blends is discussed. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Morphological,mechanical, and rheological studies of PVC/ABS blends in the presence of maleic anhydride

A novel method of enhancing compatibility in PVC/ABS blends is the use of ABS‐grafted‐(maleic anhydride) (ABS‐g‐MAH) as a compatibilizer. In this study, maleic anhydride was grafted onto ABS (initiated by peroxide) in an internal mixer. Grafting degree was determined by a back‐titration method, and certain amounts of the resultant ABS‐g‐MAH were added to PVC/ABS blends during their melt blending in the mixer. The weight ratio of PVC to ABS was kept at 70:30. Evaluation of compatibilization was accomplished via tensile and notched Izod impact tests, scanning electron microscopy (SEM), and rheological studies. According to the SEM micrographs, better dispersion of the rubber phase and its finer size in properly compatibilized blends were indications of better compatibility. Besides, in the presence of a proper amount [5 parts per hundred parts of PVC (php)] of ABS‐g‐MAH, PVC/ABS blends showed significantly higher impact strengths than uncompatibilized blends. This result, in turn, would be an indication of better compatibility. In the presence of 5 php of compatibilizer, the higher complex viscosity and storage modulus, as well as a lower loss modulus and loss factor in the range of frequency studied, indicated stronger interfacial adhesion as a result of interaction between maleic anhydride and the PVC‐SAN matrix. J. VINYL ADDIT. TECHNOL., 2010. © 2010 Society of Plastics Engineers     

Studies on morphology and thermomechanical performance of ABS/PC/organoclay hybrids

In the present research, poly(acrylonitrile‐butadiene‐styrene)/polycarbonate (ABS/PC) blends were prepared in a twin screw extruder. An attempt to reinforce and promote compatibility of the above systems was made by the incorporation of organically modified montmorillonite (OMMT, Cloisite 30B), as well as by the addition of compatibilizer (ABS grafted with maleic anhydride, ABS‐g‐MAH), and the effect of those treatments on the morphology, thermal transitions, rheological, and mechanical properties of the above blends was evaluated. The addition of compatibilizer in ABS/PC blends does not significantly affect the glass transition temperature (T_g) of SAN and PC phases, whereas the incorporation of Cloisite 30B decreases slightly the T_g values of SAN and, more significantly, that of PC in compatibilized and uncompatibilized blends. The T_g of PB phase remains almost unaffected in all the examined systems. The obtained results suggest partial dissolution of the polymeric components of the blend and, therefore, a modified Fox equation was used to assess the amount of PC dissolved in the SAN phase of ABS and vice versa.Reinforcing with OMMT enhances the miscibility of ABS and PC phases in ABS/PC blends and gives the best performance in terms of tensile strength, modulus of elasticity, and storage modulus, especially in 50/50 (w/w) ABS/PC blends. The addition of ABS‐g‐MAH compatibilizer, despite the improvement of intercalation process in organoclay/ABS/PC nanocomposites, did not seem to have any substantial effect on the mechanical properties of the examined blends. POLYM. COMPOS., 35:1395–1407, 2014. © 2013 Society of Plastics Engineers     

PP-g-MAH改性PC/ABS合金的研究

用自制马来酸酐接枝聚丙烯(PP-g—MAH)对PC／ABS舍金进行改性研究。结果表明，PP-g-MAH对PC／ABS合金有明显增容作用，可使合金的缺口冲击强度显著提高，当接枝物中马来酸酐(MAH)含量为5％、引发剂过氧化二异丙苯(DCP)含量为0．27％，PC／ABS合金中PP—g—MAH用量为2．5份时，合金综合性能最佳，其缺口冲击强度可达44kJ／m^2。     

Modification of poly(lactic) acid by reactive extrusion and its melt blending with acrylonitrile–butadiene–styrene

Poly(lactic) acid (PLA) is a biodegradable polymer that has attracted interest as a potential substitute for some thermoplastic polymers. However, its advanced brittleness at room temperature represents one of the major drawbacks for its general use. In this work, PLA was modified by reactive extrusion (PLA_REx) to enhance the rheological behaviour and to limit its degradation. The modified material was melt blended with acrylonitrile–butadiene–styrene (ABS), and the resultant morphology, rheological, thermo‐mechanical and fracture behaviour were analysed. Since PLA does not have reasonable compatibility with ABS, maleic‐anhydride‐grafted ABS (ABS‐g‐Ma) was used as compatibilizer. The morphology of the PLA_REx/ABS samples resulted in the formation of small ABS rods in the matrix. The presence of maleic anhydride contributed to reducing the interfacial energy of the blends and to obtaining finer micro‐domains of the ABS‐rich phase in the PLA_REx matrix. In the compatibilized blends, the presence of elongated ABS‐rich phases opposed free crack propagation and contributed to the increase in fracture energy in comparison to neat PLA. © 2020 Society of Chemical Industry     

The preparation and properties of compatibilized nylon 6/ABS blends using functionalized polybutadiene. Part I: Impact properties

The impact behaviors of nanoclay filled nylon 6 (nano‐nylon 6) or nylon 6 blended with poly(acrylonitrile‐butadiene‐styrene) terpolymers (ABS) were investigated here using polybutadiene grafted maleic anhydride (PB‐g‐MA) as a compatibilizer to enhance interphase interaction. It is found that impact strength increases slightly for nano‐nylon 6/ABS blend system with the addition of compatibilizer at various ABS compositions, but increases to a certain degree for nylon 6/ABS case. Similar effects are also found with decreasing test temperature, especially at a blend composition of 80/20. These discrepancies are attributed to a different degree of available reaction sites from amine group on nano‐nylon 6 and nylon 6 as well as the rigidity of clay in deteriorating toughness. As for thermal properties, the heat distortion temperature shows marginally decrease in the nano‐nylon 6/ABS blend. Through morphology observations, the etched ABS particle sizes tend to decrease with the additions of compatibilizer for both blends, but are larger with higher contents of ABS concentrations. Those observations account for impact behaviors of the investigated blends. POLYM. ENG. SCI., 45:1461–1470, 2005. © 2005 Society of Plastics Engineers     

Investigation on the morphological and mechanical properties of (polyamide 6)/(poly[styrene‐co‐acrylonitrile])/(poly[styrene‐b‐{ethylene‐co‐butylene}‐b‐styrene]) ternary blends

In this work, ternary polymer blends based on (polyamide 6)/(poly[styrene‐co‐acrylonitrile])/(poly[styrene‐b‐{ethylene‐co‐butylene}‐b‐styrene]) (SEBS) triblock copolymer and a varying concentration of the reactive (maleic anhydride)‐grafted SEBS were prepared by using a melt‐blending process. The effects of the material parameters (composition of ternary blends and SEBS/[{maleic anhydride}‐grafted SEBS] concentration ratio) and blending sequence on the morphological and mechanical properties of ternary blends were studied. Taguchi experimental design methodology was employed to design the experiments and select the material and processing parameters for the optimized mechanical properties. Tensile properties (Young's modulus and yield stress) and impact strength were considered as the response variables. It was demonstrated that there is a meaningful relationship between the composition of blends, processing parameters, observed phase structure, and obtained mechanical properties. The mechanical tests showed that the highest impact strength was achieved as the dispersion of the rubbery phase achieved an optimum size of about 1 μm. J. VINYL ADDIT. TECHNOL., 23:329–337, 2017. © 2015 Society of Plastics Engineers     

Properties and preparation of compatibilized nylon 6 nanocomposites/ABS blends using functionalized metallocene polyolefin elastomer. I. Impact properties

The impact behaviors of nanoclay‐filled nylon 6 (nano‐nylon 6) blended with poly(acrylonitrile–butadiene–styrene) terpolymers (ABS) prepared through a twin screw mixing process were investigated here using metallocene polyethylene grafted maleic anhydride (POE‐g‐MA) as a compatibilizer to enhance the interface interaction. No clear effect of compatibilizer on the dispersion of clay and crystalline structure of nano‐nylon 6 has been observed. In view of morphology and rheological behaviors, the effect of compatibilizer on the mechanical properties could be elucidated. It is found that impact strength increases with the addition of compatibilizer at various ABS compositions. Similar effects are also observed with decreasing test temperature at the nano‐nylon 6/ABS blend composition of 80/20. As for thermal properties, the heat distortion temperature shows a marginal decrease in the nano‐nylon 6/ABS blends. Rheological behavior indicates that increased viscosity is found for the investigated compatibilized systems. Through morphology observations, the etched ABS particle sizes tend to decrease with the addition of compatibilizer for the blends, but are larger with higher contents of ABS concentrations. Those observations account for impact behaviors of the investigated blends. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1364–1371, 2006     

Compatibilization of polypropylene/Poly(acrylonitrile‐butadiene‐styrene) blends by polypropylene‐graft‐cardanol

The polypropylene‐graft‐cardanol (PP‐g‐cardanol) was prepared by reactive extrusion with polypropylene (PP) and natural renewable cardanol which could increase the interfacial energy of PP and inhibit the degradation of PP during the process of reactive extrusion and usage. In this article, PP‐g‐cardanol and polypropylene‐graft‐maleic anhydride (PP‐g‐MAH) were used as compatibilizers of the polypropylene (PP)/poly(acrylonitrile‐butadiene‐styrene) (ABS) blends. PP/ABS (70/30, wt %) blends with PP‐g‐cardanol and PP‐g‐MAH were prepared by a corotating twin‐screw extruder. From the results of morphological studies, the droplet size of ABS was minimized to 1.93 and 2.01 μm when the content of PP‐g‐cardanol and PP‐g‐MAH up to 5 and 7 phr, respectively. The results of mechanical testing showed that the tensile strength, impact strength and flexural strength of PP/ABS (70/30) blends increase with the increasing of PP‐g‐cardanol content up to 5 phr. The complex viscosity of PP/ABS (70/30) blends with 5 phr PP‐g‐cardanol showed the highest value. Moreover, the change of impact strength and tensile strength of PP/ABS (70/30) blends were investigated by accelerated degradation testing. After 4 accelerated degradation cycles, the impact strength of the PP/ABS (70/30) blends with 5 phr PP‐g‐cardanol decrease less than 6%, but PP/ABS (70/30) blends with 5 phr PP‐g‐MAH and without compatibilizer decrease as much as 12% and 32%, respectively. The tensile strength of PP/ABS (70/30) blends has a similar tendency to that of impact strength. The above results indicated that PP‐g‐cardanol could be used as an impact modifier and a good compatibilizer, which also exhibited better stability performance during accelerated degradation testing. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41315.     

聚环氧酯的合成及其对PC/ABS相容性的影响

以双酚A环氧树脂和己二酸合成了聚己二酸环氧酯,将环氧酯作为相容剂加入到PC/ABS中通过双螺杆挤出机并注射成型制备了合金,与马来酸酐接枝聚苯乙烯（SMA）相容剂增容的合金的力学性能及分散形态进行了对比。结果表明,聚环氧酯对PC相具有良好的相容性,而SMA对ABS相的相容性较好,二者复合使用可以显著改善合金的相容性;聚环氧酯能明显提高PC/ABS合金的拉伸强度和缺口冲击强度,但过量加入会降低合金的冲击强度;SEM结果表明少量的聚环氧酯即可以使ABS分散相分布均匀,与SMA并用可以使分散相尺寸减小,提高相容性。     

Mechanical performance of ternary in situ polycarbonate/poly(acrylonitrile‐butadiene‐styrene)/liquid crystalline polymer composites

Ternary in situ polycarbonate (PC)/poly(acrylonitrile‐butadiene‐styrene) (ABS)/liquid crystalline polymer(LCP) composites were prepared by injection molding. The LCP used was a versatile Vectra A950, and the matrix of composite specimens was PC/ABS 60/40 by weight. Maleic anhydride (MA) copolymer and solid epoxy resin (bisphenol type‐A) were used as compatibilizers for these composites. The tensile, dynamic mechanical, impact, morphology, and thermal properties of the composites were studied. Tensile tests showed that the tensile strength of the PC/ABS/LCP composite in the longitudinal direction increased markedly with increasing LCP content. However, it decreased slowly with increasing LCP content in the transverse direction. The modulus of this composite in the longitudinal direction appeared to increase considerably with increasing LCP content, whereas the incorporation of LCP into PC/ABS blends had little effect on the modulus in the transverse direction. The impact tests revealed that the Izod impact strength of the composites in both longitudinal and transverse direction decreased with increasing LCP content up to 15 wt %; thereafter it increased slowly with increasing LCP. Dynamic mechanical analyses (DMA) and thermogravimetric measurements showed that the heat resistance and heat stability of the composites tended to increase with increasing LCP content. Scanning electron microscopy observation and DMA measurement indicated that the additions of epoxy and MA copolymer to PC/ABS matrix appeared to enhance the compatibility between the PC and ABS, and between the matrix and LCP. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2274–2282, 1999