Effect of high‐temperature annealing on the microstructure and mechanical properties of polypropylene with shish kebab or spherulite structure

Various annealing temperatures below, near, or above the melting temperature were used to anneal polypropylene with oriented shish kebab and isolated spherulite structures in this work. The results showed that a high annealing temperature decreases the time needed to achieve the ideal material property. When the annealing temperature is near or above the melting temperature, the impact strength would be 1.6 times improved by partial melting and recrystallization. The crystal structure of the oriented shish kebab or isolated spherulite structures was improved when annealed at 150 °C, whereas annealing at 165 or 170 °C recombined the crystal lamellae of the structure. Moreover, the high crystallinity and thick lamellae improved the impact and yield strength values of the spherulite structure. However, excessively high crystallinity and thick lamellae in the oriented shish kebab structure did not result in good mechanical performance. Therefore, the prediction of mechanical properties for the shish kebab structure based on crystallinity and lamellar thickness is not feasible. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46465.     

Effect of the comonomer content on the solid‐state mechanical and viscoelastic properties of poly(propylene‐co‐1‐butene) films

In this study, we quantified the thermal and solid‐state mechanical and viscoelastic properties of isotactic polypropylene (i‐PP) homopolymer and poly(propylene‐1‐butene) copolymer films having a 1‐butene ratio of 8, 12, and 14 wt %, depending on the comonomer content. The uniaxial tensile creep and stress‐relaxation behaviors of the samples were studied in a dynamic mechanical analyzer at different temperatures. The creep behaviors of the samples were modeled with the four‐element Burger equation, and the long‐term creep strains were predicted with the time–temperature superposition method. The short‐term mechanical properties of the samples were also determined with tensile and impact testing at room temperature. We found that the Young's modulus and ultimate strength values of the samples decreased with increasing amount of 1‐butene in the copolymer structure. On the other hand, the strain at break and impact strength values of the samples improved with increasing amount of 1‐butene. Creep analysis showed that i‐PP exhibited a relatively lower creep strain than the poly(propylene‐co‐1‐butene)s at 30 °C. However, interestingly, we discovered that the temperature increase resulted in different effects on the creep behaviors. We also found that short‐chain branching improved the creep resistance of polypropylene at relatively high temperatures. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46350.     

Synergistic effects of β‐modification and impact polypropylene copolymer on brittle‐ductile transition of polypropylene random copolymer

In this work, the synergistic effects of β‐modification and impact polypropylene copolymer (IPC) on brittle–ductile (B–D) transition behavior of polypropylene random copolymer (PPR) have been investigated. It is interesting to find that adding both IPC and β‐nucleating agent into PPR has three effects: (i) leading to a significant enhancement in β‐crystallization capability of PPR, (ii) contributing to the shift of B–D transition to lower temperatures, (iii) increasing the B–D transition rate. The reason for these changes can be interpreted from the following two aspects. On one hand, the transition of crystalline structure from α‐form to β‐form reduces the plastic resistance of PPR matrix, thus causing the initiation of matrix shear yielding much easier during the impact process. On the other hand, the well dispersed rubbery phase in IPC with high molecular mobility at relatively low temperatures is beneficial to the shear yielding of PPR matrix and, subsequently, the great improvement in impact toughness of the ternary blends. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Effects of 4,4′‐diaminodiphenyl ether on the structures and properties of isocyanate‐based polyimide foams

A series of thermal insulation, acoustic absorption isocyanate‐based lightweight polyimide (PI) foams with 4,4′‐diaminodiphenyl ether (ODA) units were prepared from polyaryl polymethylene isocyanate (PAPI) and the esterification solution derived from pyromellitic dianhydride (PMDA) and ODA. The structures and properties of the PI foams prepared with different molar ratio of ODA/PMDA were investigated in detail. The results show that the ODA units have great influence on the foam properties. With the increase of the ODA units, the density decreases firstly and then increases. When the molar ratio of ODA/PMDA is 3/10, the foam reaches the minimum density (13.7 kg/m³). Moreover, with increasing the ODA units, the acoustic absorption properties increase firstly and then decrease owing to the variation of the average cell diameter of the PI foams. All PI foams show excellent thermal stability, and the 5% and 10% weight loss temperature are in the range of 250–270 °C and 295–310 °C, respectively. In addition, the PI foams present low thermal conductivity and thermal diffusivity. Furthermore, the mechanical property was also evaluated and the compressive strength of the PI foams is in the range of 33.0–45.7 kPa. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46029.     

Influences of pre‐ordered melt structures on the crystallization behavior and polymorphic composition of β‐nucleated isotactic polypropylene with different stereo‐defect distribution

As part of continuous efforts to understand the surprising synergetic effect between β‐nucleating agent and pre‐ordered structures of isotactic polypropylene (iPP) in significant enhancement of β‐crystallization (Ordered Structure Effect, OSE), two β‐nucleated iPP with different uniformities of stereo‐defect distribution (WPP‐A and WPP‐B) were prepared, their crystallization behaviors with variation of melt structures were studied in detail. The results revealed that β‐phase can hardly form in WPP‐A (whose stereo‐defect distribution is less uniform) because of its strong tendency of α‐nucleation caused by its less uniform stereo‐defect distribution, while WPP‐B is more favorable for β‐crystallization; As fusion temperature decreases, similar variation trends of crystallization temperature and β‐phase proportion can be observed from WPP‐A and WPP‐B, indicating the occurrence of OSE behavior, which provides unsurpassed β‐nucleation efficiency and induces β‐crystallization even in WPP‐A which is less favorable for β‐crystallization; moreover, the upper and lower limiting temperatures of Region II of WPP‐A and WPP‐B are identical, suggesting the uniformity of stereo‐defect distribution has little influence on temperature window for OSE (denoted as Region II). To explore the physical nature of Region II, self‐nucleation behavior and equilibrium melting temperature of PP‐A and PP‐B were studied. The lower limiting temperatures of exclusive self‐nucleation domain of both PP‐A and PP‐B are identical with the lower limiting temperatures of Region II in OSE (168°C); moreover, the T_m⁰ of both PP‐A and PP‐B are close to their upper limiting temperatures of Region II in OSE behavior (189°C). The possible explanation was proposed. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42632.     

Simultaneously improving tensile strength and toughness of melt‐spun β‐nucleated isotactic polypropylene fibers

Polymer processing methods generally play a crucial role in determining the development of microstructure in the fabricated product. In this study, isotactic polypropylene (iPP) melt containing 0.05 wt % β‐nucleating agent (β‐NA) was extruded via a melt flow rate indicator. The molten extrudate was stretched into a fiber upon various take‐up velocities (TVs). The microstructures of the fiber were investigated by differential scanning calorimeter, two‐dimensional wide‐angle X‐ray diffraction, and small‐angle X‐ray scattering. Also, its tensile properties (including tensile strength, modulus, elongation at break, and toughness) were measured by tensile test. Interestingly, the tensile strength (135.0 MPa) of a melt‐spun β‐nucleated iPP fiber fabricated at 400 cm/min was enhanced by 115.2%, compared with that (62.7 MPa) prepared at 100 cm/min, with a considerable increment in toughness (from 661 to 853 MJ/m³). The enhancement mechanism for tensile properties was discussed based on the microstructures. This work offers a simple approach to prepare β‐nucleated iPP fibers with excellent strength and toughness. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43454.     

Structure evolution and orientation mechanism of isotactic polypropylene during the two‐stage solid die drawing process

High oriented isotactic polypropylene prepared by self‐designed two‐stage die drawing apparatus was explored through kinds of methods, including differential scanning calorimetry, two‐dimensional wide‐angle X‐ray diffraction, polarized light microscope, and tensile test. The results showed that there was a great difference between the orientation mechanism and structure evolution of two‐stage solid die drawing process and single‐stage solid die drawing process. All samples would undergo free drawing process after die drawing process. Die drawing and free drawing process were of equal importance to single‐stage die drawing process while die drawing process showed an prominent contribution to the two‐stage die drawing process. Drawing speed showed beneficial influence on die drawing process for both single‐ and two‐stage die drawing process routes. Under the same processing condition, tensile strength and modulus of samples prepared by two‐stage die drawing process were higher than those prepared by single‐stage die drawing process and the maximum value could reach 241.93 MPa and 3.57 GPa, respectively. Moreover, two‐stage die drawing samples showed better dimensional stability than single‐stage die drawing samples especially under low draw rate. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46581.     

The influence of filler surface modification on mechanical and material properties of layered double hydroxide‐containing polypropylene composites

The processing and properties of layered double hydroxides (LDHs)‐containing polypropylene (PP) composites have been studied extensively. However, no detailed studies have reported on how stearic acid (SA)‐intercalated and SA‐coated LDHs influence the properties of melt‐processed PP/LDH composites. Here, four different types of LDHs: synthesized (cLDH1) and commercial (cLDH2) SA‐coated LDH, SA‐intercalated LDH (iLDH), and unmodified LDH (nLDH), were used to fabricate composites using a master‐batch‐dilution technique in a twin‐screw extruder. The characterization results showed that microcomposites were formed when cLDH2 and nLDH were used, whereas nanocomposites were formed when iLDH and cLDH1 were used. Strong nucleating behavior was observed for the nLDH‐, cLDH1‐, and cLDH2‐containing composites, whereas iLDH delayed the crystallization process of the PP matrix. A significant improvement in modulus, with a balance of tensile and impact strengths, was observed in the case of the cLDH1‐containing composite, whereas the nLDH‐containing composite showed good improvement in temperature‐dependent load‐bearing capacity. On the other hand, the PP/iLDH composite showed a remarkable improvement in thermal stability and a reduction in the peak‐heat‐release rate. Therefore, this study gives us an opportunity to design PP composites with desired properties by the judicious choice of LDH, which further widens the application of PP matrices. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45024.     

Effect of nanoparticles on the mechanical properties of acrylonitrile–butadiene–styrene specimens fabricated by fused deposition modeling

Acrylonitrile–butadiene–styrene (ABS) nanocomposite filaments with different inorganic nanofillers for fused deposition modeling (FDM) were prepared by melting extrusion and printed via a commercial FDM three‐dimensional printer. The effects of the nanoparticles on the mechanical strength, anisotropy, and thermal properties of the ABS specimens were evaluated. The performances of the virgin ABS samples manufactured by FDM and injection molding were also studied. The results show that the tensile strength (TS) of the pure ABS made by FDM was just up to 70% of the value obtained from the injection‐molded specimens. The mechanical anisotropy of the pure ABS samples was very evident when the building orientation was changed. However, we found that the addition of nanofillers significantly reduced the mechanical anisotropy and improved the mechanical strength and thermostability of the ABS samples fabricated by FDM technology. The TS and flexural strength of the ABS samples increased by 25.7 and 17.1%, respectively, with the introduction of nanomontmorillonite. The addition of nano calcium carbonate lowered the mechanical anisotropy of ABS from 42.1 to 23.9%. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44470.     

Dynamic mechanical analysis of ethylene/1‐hexene copolymers: The effect of the catalyst type on the short‐chain branching distribution and properties of the amorphous and crystalline phases

Dynamic mechanical analysis was used to study ethylene/1‐hexene copolymers with different compositions, molecular weight distributions, and profiles of short‐chain branching (SCB) versus molecular weight. These copolymers were produced over a highly active supported titanium–magnesium catalyst (TMC), a highly active supported vanadium–magnesium catalysts (VMC), and a supported zirconocene catalyst. A higher fraction of the crystalline phase in the copolymers prepared with VMC was shown to result in higher elastic modulus values. β relaxation was found to be sensitive to the SCB distribution versus the molecular weight. The copolymers prepared with the zirconocene catalyst and VMC were characterized by more uniform SCB distributions and higher temperatures of β relaxation compared to the copolymers prepared with TMC. The mobility of the polymer chains at room temperature in the amorphous phase obtained by the spin‐probe method rose with increasing branch content in the copolymers and was not sensitive to different SCB distribution profiles. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44638.     

Fabrication of polypropylene blends with excellent low‐temperature toughness and balanced toughness‐rigidity by a combination of EPR and SEEPS

To overcome serious rigidity depression of rubber‐toughened plastics and fabricate a rigidity‐toughness balanced thermoplastic, a combination of styrene‐[ethylene‐(ethylene‐propylene)]‐styrene block copolymer (SEEPS) and ethylene‐propylene rubber (EPR) was used to toughen polypropylene. The dynamic mechanical properties, crystallization and melting behavior, and mechanical properties of polypropylene (PP)/EPR/SEEPS blends were studied in detail. The results show that the combination of SEEPS and EPR can achieve the tremendous improvement of low‐temperature toughness without significant strength and rigidity loss. Dynamic mechanical properties and phase morphology results demonstrate that there is a good interfacial strength and increased loss of compound rubber phase comprised of EPR component and EP domain of SEEPS. Compared with PP/EPR binary blends, although neither glass transition temperature (T_g) of the rubber phase nor T_g of PP matrix in PP/EPR/SEEPS blends decreases, the brittle‐tough transition temperature (T_bd) of PP/EPR/SEEPS blends decreases, indicating that the increased interfacial interaction between PP matrix and compound rubber phase is also an effective approach to decrease T_bd of the blends so as to improve low‐temperature toughness. The balance between rigidity and toughness of PP/EPR/SEEPS blends is ascribed to the synergistic effect of EPR and SEEPS on toughening PP. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45714.     

Reaction‐induced phase separation and resulting thermomechanical and surface properties of epoxy resin/poly(ethylene oxide)–poly(propylene oxide)–poly(ethylene oxide) blends cured with 4,4′‐diaminodiphenylsulfone

We investigated the phase separation, cure kinetics and thermomechanical properties of diglycidyl ether of bisphenol‐A/4,4′‐diaminodiphenylsulfone/poly(ethylene oxide)–poly(propylene oxide)–poly(ethylene oxide) (PEO–PPO–PEO) triblock copolymer (TBCP) blends. Fourier transform infrared spectroscopy, differential scanning calorimetry, and atomic force microscopy revealed that the blends exhibited heterogeneous phase morphology in which the TBCP formed dispersed domains in epoxy matrix, due to reaction induced phase separation. A fraction of phase‐separated PEO phase underwent partial crystallization whereas another fraction formed interphases between the dispersed domains and epoxy matrix. Moreover, the dispersed PEO chains improved the compatibility and interfacial adhesion between the matrix and domains and, consequently, significantly improved the mechanical properties of epoxy resin. Furthermore, the thermal degradation studies and contact angle measurements disclosed that the dispersed domains were well protected by the epoxy matrix. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44406.     

Mechanical properties and network structure of phenol resin crosslinked hydrogenated acrylonitrile‐butadiene rubber

The tough and stretchable crosslinked hydrogenated acrylonitrile–butadiene rubber (HNBR) could be prepared by resol type phenol resin as a crosslinker. The mechanical properties and the network structure of the phenol resin crosslinked HNBR were investigated by comparing with those of the peroxide crosslinked HNBR having the higher crosslink density and the heterogeneous network structure. The elastic modulus and the strain at break of the phenol resin crosslinked HNBR were much higher than those of the peroxide one. The residual strain was below 20 % after stretching up to 650 % and then releasing from the cramps. Since the crosslink density is low, the high elastic modulus and the good recovery deformation are attributed to the stiffness and rigidity of the crosslink junctions obtained by phenol resin. Small‐angle X‐ray scattering measurements revealed that the network structure is spatially homogeneous and the results of the wide angle X‐ray diffraction indicate that the strain‐induced crystallization is suppressed, which enable the longer elongation. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Strain rate dependent mechanical properties of a high‐strength poly(methyl methacrylate)

Strain rate dependency is an important issue for the mechanical response of materials in impact events. Dynamic mechanical properties of a high‐strength poly(methyl methacrylate) (PMMA) were studied by using split Hopkinson pressure bar technology. The maximum stress is enhanced with the increase of strain rate, and then keeps a constant with the further increase of strain rate, which is accompanied with a linear increase of fracture energy density. The critical data of strain rate and maximum stress were determined. Eyring's equation was applied for analyzing the influence factors, which relate to the hardening induced by strain rate and softening caused by adiabatic temperature rise. Inherent physical mechanisms were clarified and the strategies for designing advanced impact‐resistant polymers were proposed. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46189.     

Tailoring the crystalline morphologies and mechanical properties of high‐density polyethylene parts by a change in the fluid flow pattern under gas‐assisted injection molding

In this study, an increase in the cooling rate of high‐density polyethylene parts was carried out via a change in the fluid flow pattern to introduce gas cooling under a gas‐assisted injection‐molding process; this was conducive to the retention of orientation chains shaped during the injection stage and further developed into much more oriented crystals. Morphological observation showed that the parts without gas cooling (WOGC) were composed of oriented crystals except the gas channel zone, whereas the parts with gas cooling (WGC) were full of oriented crystals, especially much more interlocking shish‐kebab structures in the subskin zone. The WGC parts had a higher degree of orientation than the corresponding zone of the WOGC parts. Although the lower crystallinity, the wider orientation regions, and much more interlocking shish‐kebab structures led to considerable increases from 32 and 990 MPa in the WOGC parts to 36 and 1150 MPa in the WGC parts for the yield strength and elastic modulus, respectively. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40349.     

Synergistic effect of α‐ZrP and graphene oxide nanofillers on the gas barrier properties of PVA films

Two types of 2D nanofillers, α‐zirconium phosphate (α‐ZrP) and graphene oxide (GO), were synthesized and incorporated into poly(vinyl alcohol) (PVA) with 1 wt % loading level at various α‐ZrP:GO (Z:G = 5:1, 2:1, 1:1, 1:2, and 1:5) ratios. The resulting nanocomposites were tested for barrier properties by casting films from solution. The structure and morphology of α‐ZrP and GO were characterized by Fourier‐transform infrared spectroscopy, atomic force microscope, scanning electron microscopy, transmission electron microscopy, and X‐ray diffraction, which demonstrated successful preparation of exfoliated α‐ZrP and GO. The physical characteristics of the nanocomposite films, including thermal, mechanical, and gas barrier properties were investigated. The results indicated that the tensile strength, Young's modulus, and elongation at break of the PVA nanocomposite films with Z:G hybrid nanofiller improved compared to neat PVA. The glass transition temperature, melting temperature, and crystallinity also increased. Consequently there appears to be a synergistic effect with these two types of nanofillers that formed a specific macro structure of a “wall.” This macrostructure resulted in excellent O₂ gas barrier properties with the PVA/Z:G‐5:1 nanocomposite films having the best performance. The of the PVA/Z:G‐5:1 nanocomposite decreased from 1.835 × 10^?16 to 0.587 × 10^?16 cm³ cm cm^?2 s^?1 Pa^?1 compared with neat PVA. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46455.     

Thermal,mechanical, and rheological properties of poly(ε‐caprolactone)/halloysite nanotube nanocomposites

Naturally available halloysite nanotubes (HNTs) with hollow nanotubular structures were used as reinforcement in poly(ε‐caprolactone) (PCL). The PCL/HNT nanocomposites were prepared by melt mixing the polymer with as‐received HNTs up to 10 wt % in an internal batch mixer. Transmission electron microscopy analysis indicated that the HNTs were dispersed uniformly on the nanoscale throughout the PCL matrix. Differential scanning calorimeter studies revealed that the PCL crystallinity was decreased in the nanocomposites, and the HNTs dispersed in the PCL matrix led to an increase in the non‐isothermal crystallization temperature of the PCL. Tensile and dynamic mechanical tests showed great enhancement in strength and stiffness at low HNT content, while still maintaining the ductility of the PCL. The glass transition temperature (T_g) of the pristine PCL was substantially increased with increase in filler loading, which indicates good reinforcing effect imparted by the addition of HNT. Melt rheological studies revealed that the nanocomposites exhibited strong shear thinning behavior, and a percolated network of HNT particles was formed. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Preparation and properties of β‐phase graphene oxide/PVDF composite films

We report preparation of graphene oxide (GO) from expanded graphite (EG) via a modified Hummers method. GO/PVDF composites films were obtained using solvent N, N‐Dimethylformamide (DMF) and cosolvent comprising deionized water/DMF combination. X‐ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR) analyses revealed that the main crystal structure of the composite films is β‐phase, and use cosolvent method tends to favor the formation of β‐phase. Scanning electron microscopy (SEM) was used to investigate the microstructure of composite films. Storage modulus and loss modulus were measured by Dynamic mechanical analysis (DMA). Broadband dielectric spectrum tests showed an increase in the dielectric constant of the GO/PVDF composite films with the rising content of GO, and by cosolvent method could improve the dielectric constant while reducing the dielectric loss. Our method that uses GO as an additive and deionized water/DMF as the cosolvent provides a promising and low‐cost pathway to obtain high dielectric materials. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41577.     

Different β nucleants and the resultant microstructural,fracture, and tensile properties for filled and unfilled ISO polypropylene

This article explores the use of two β nucleants to improve the fracture behavior of filled and unfilled homo‐polypropylene (PP). The first was based upon an organic quinacridone, whereas the second was based upon the inorganic calcium pimelate. Formulations containing various concentrations of nucleant were prepared using single screw extrusion and then characterized by X‐ray diffraction, differential scanning calorimetry (DSC), Izod impact strength, and tensile testing. The quinacridone nucleating agent produced higher levels of β crystallinity and better improvement in strain to failure, whereas the calcium pimelate imparted greater improvement in impact strength regardless of whether the PP was filled or unfilled. No direct relationship between β crystallinity and fracture properties was observed though synergistic enhancement in impact strength was evident. By varying the concentration of calcium carbonate in the calcium pimelate from 10 : 1, 5 : 1, 2 : 1, and 1 : 1 weight composition of calcium carbonate to pimelic acid, similar property enhancements were achieved regardless of composition although the 10 : 1 sample did produce superior elongation to break. The importance of cooling rate on microstructure within each sample was explored via a through the thickness study using DSC and nano‐indenting methods. Variations in the β content through the thickness were related to cooling and found to be independent of sample composition and processing. Elastic properties varied inversely with β content. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

A highly active and selective β‐nucleating agent for isotactic polypropylene and crystallization behavior of β‐nucleated isotactic polypropylene under rapid cooling

Zinc adipate (Adi‐Zn) was observed to be a highly active and selective β‐nucleating agent for isotactic polypropylene (iPP). The effects of Adi‐Zn on the mechanical properties and the β‐crystals content of nucleated iPP were investigated. The impact strength of iPP nucleated with 0.2 wt % Adi‐Zn was 1.8 times higher than that of neat iPP. In addition, wide‐angle X‐ray diffraction analysis indicated that the content of β‐crystals in nucleated iPP (k_β value) reached 0.973 with 0.1 wt % Adi‐Zn, indicating that Adi‐Zn is a highly active and selective β‐nucleating agent for iPP. Furthermore, fast scanning chip calorimetry (FSC) studies using cooling rates from 60 to 13,800 °C min^?1 revealed that the formation of β‐crystals significantly depended on the cooling rates. At cooling rates below 3000 °C min^?1, only β‐crystals existed. However, at cooling rates above 6000 °C min^?1, β‐crystals failed to form. Moreover, a lower critical crystallization temperature that corresponded to the generation of β‐crystals was investigated using cooling‐induced crystallization, and the results are in good agreement with those of a previous study. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43767.