Preparation and proton conductivity of phosphoric acid‐doped blend membranes composed of sulfonated block copolyimides and polybenzimidazole

A series of phosphoric acid (PA)‐doped blend membranes composed of block or random sulfonated polyimides (SPIs) and polybenzimidazole (PBI) were prepared with similar PA contents to investigate the influence of chemical structures of SPIs on proton conductivity. The proton conductivity of a PA‐doped blend membrane containing block‐type SPI, PA‐bSPI(80/20)/oPBI, was higher than that of the corresponding pristine block‐type SPI, PA‐SPI/PBI containing random‐type SPI and Nafion membranes over a wide temperature range, and reached 0.37 S cm^?1 at 90 °C and 98% relative humidity. The PA‐bSPI(80/20)/oPBI membrane also showed distinct proton conductivity even at low humidity due to a new proton transport pathway among PA and sulfonic acid groups. Also, the novel PA‐doped blend membrane showed higher proton conductivity than Nafion at both above 100 °C and below 0 °C under low relative humidity conditions. © 2013 Society of Chemical Industry     

Synthesis and Characterization of a New Fluorine‐Containing Polybenzimidazole (PBI) for Proton‐Conducting Membranes in Fuel Cells

A new type of fluorine‐containing polybenzimidazole, namely poly(2,2′‐(2,2′‐bis(trifluoromethyl)‐4,4′‐biphenylene)‐5,5′‐bibenzimidazole) (BTBP‐PBI), was developed as a candidate for proton‐conducting membranes in fuel cells. Polymerization conditions were experimentally investigated to achieve high molecular weight polymers with an inherent viscosity (IV) up to 1.60 dl g^–1. The introduction of the highly twisted 2,2′‐disubstituted biphenyl moiety into the polymer backbone suppressed the polymer chain packing efficiency and improved polymer solubility in certain polar organic solvents. The polymer also exhibited excellent thermal and oxidative stability. Phosphoric acid (PA)‐doped BTBP‐PBI membranes were prepared by the conventional acid imbibing procedure and their corresponding properties such as mechanical properties and proton conductivity were carefully studied. The maximum membrane proton conductivity was approximately 0.02 S cm^–1 at 180 °C with a PA doping level of 7.08 PA/RU. The fuel cell performance of BTBP‐PBI membranes was also evaluated in membrane electrode assemblies (MEA) in single cells at elevated temperatures. The testing results showed reliable performance at 180 °C and confirmed the material as a candidate for high‐temperature polymer electrolyte membrane fuel cell (PEMFC) applications.     

Polybenzimidazole/inorganic composite membrane with advanced performance for high temperature polymer electrolyte membrane fuel cells

In this work, Al–Si was synthesized via a sol–gel process and introduced in poly 2,2′‐m‐(phenylene)‐5,5′‐bibenzimidazole (PBI). As a result, a series of five Al–Si/PBI composite (ASPBI) membranes (0, 3, 6, 9, and 12 wt%) were developed and characterized for application in high temperature polymer electrolyte membrane fuel cells (HT‐PEMFCs). The chemical and morphological structure of ASPBI membranes were analyzed by Fourier transform infrared spectroscopy, X‐ray diffractometer, and scanning electron microscopy. According to the doping level test and thermogravimetric analysis, as the concentration of Al–Si increased, the doping level increased up to 475% due to the affinity and interaction between Al and phosphoric acid (PA). Moreover, the proton conductivity, current density at 0.6 V, and maximum power density of ASPBI membranes increased up to 0.31 S cm⁻¹, 0.320 A cm⁻², and 0.370 W cm⁻², respectively, because the increased concentration of Al–Si allows the membranes to hold more PA. Alternatively, as the amount of Al–Si increased, the tensile strength of PA‐doped and ‐undoped membranes decreased. This was caused by both excess PA and aggregation, which can cause serious degradation of the membrane and induce cracks. Furthermore, the PA‐doped and ‐undoped ASPBI12 had the lowest tensile strength of 11.6 and 77.2 MPa. The improved proton conductivity and single cell performance of ASPBI membranes implies that these membranes are possible candidates for HT‐PEMFC applications. However, further studies seeking to enhance the compatibility between PBI and Al–Si and optimize the amount of filler should be performed. POLYM. COMPOS., 38:87–95, 2017. © 2015 Society of Plastics Engineers     

Preparation and Characterisation of Proton Exchange Membranes Based on Crosslinked Polybenzimidazole and Phosphoric Acid

Crosslinked polybenzimidazole (PBI) was synthesised via free radical polymerisation between N‐vinylimidazole and vinylbenzyl substituted PBI. The degree of crosslinking increases with increasing content of the crosslinker. The phosphoric acid doping behaviour, mechanical properties, proton conductivity and acid migration stability of crosslinked PBI and linear PBI are discussed. The results show that the acid doping ability decreases with increasing degree of crosslinking of PBI. The introduction of N‐vinylimidazole in PBI is beneficial to its oxidation stability. The mechanical stability of crosslinked PBI/H₃PO₄ membrane is better than that of linear PBI/H₃PO₄ membrane. The proton conductivity of the acid doped membranes can reach ∼10^–4 S cm^–1 for crosslinked PBI/H₃PO₄ composite membranes at 150 °C. The temperature dependence of proton conductivity of the acid doped membranes can be modelled by an Arrhenius relation. The proton conductivity of crosslinked PBI/H₃PO₄ composite membranes is a little lower than that of linear PBI/H₃PO₄ membranes with the same acid content. However, the migration stability of H₃PO₄ in crosslinked PBI/H₃PO₄ membranes is improved compared with that of linear PBI/H₃PO₄ membranes.     

Effect of composition on the properties of PEM based on polybenzimidazole and poly(vinylidene fluoride) blends

Inadequate performance, short term durability and high cost of polymer electrolyte membrane (PEM) are the major roadblocks that need to be resolved for successful commercialization of high temperature PEM fuel cell. In this report, we investigated the viability of previously developed miscible blend membranes of polybenzimidazole and poly (vinylidene fluoride) (PBI/PVDF), as potential PEMs. In addition, we have carried out several advanced analytical techniques such as dynamic mechanical analysis (DMA), ¹³C CP-MAS solid state NMR (SS-NMR) and wide-angle X-Ray diffraction (WAXD) to prove the miscible behavior of the polymer pair. Sub-ambient temperature DMA studies confirmed the miscible behavior of PBI/PVDF blends at different compositions based on single T_g criterion. SS-NMR and WAXD showed the presence of interactions between the functional groups of the polymers and their dependence on blend composition. Thermogravimetric analysis of phosphoric acid (PA) doped and undoped blend membranes confirmed the improved thermal stability of the membranes compared to neat PBI. The membranes exhibited excellent oxidative stability than pristine PBI membrane. The swelling ratio and volume after dipping in PA was found to be significantly low in the blend membranes owing to the hydrophobic nature of PVDF. Among the blends prepared, 90/10 and 75/25 membranes showed higher proton conductivity than PBI, attributed in part, to electronegativity of fluorine and crystallinity of PBI in PA that activate proton transport. The results demonstrated the potential usefulness of the blend membranes as PEM in fuel cell.     

Organic/inorganic composite membranes based on polybenzimidazole and nano-SiO2

Organic/inorganic composite membranes based on polybenzimidazole (PBI) and nano-SiO₂ were prepared in this work. However, the preparation of PBI/SiO₂ composite membrane is not easy since PBI is insoluble in water, while nano-SiO₂ is hydrophilic due to the hydrophilicity of nano-SiO₂ and water-insolubility of PBI. Thus, a solvent-exchange method was employed to prepare the composite membrane. The morphology of the composite membranes was studied by scanning electron microscopy (SEM). It was revealed that inorganic particles were dispersed homogenously in the PBI matrix. The thermal stability of the composite membrane is higher than that of pure PBI, both for doped and undoped membranes. PBI/SiO₂ composite membranes with up to 15 wt% SiO₂ exhibited improved mechanical properties compared with PBI membranes. The proton conductivity of the composite membranes containing phosphoric acid was studied. The nano-SiO₂ in the composite membranes enhanced the ability to trap phosphoric acid, which improved the proton conductivity of the composite membranes. The membrane with 15 wt% of inorganic material is oxidatively stable and has a proton conductivity of 3.9 × 10⁻³ S/cm at 180 °C.     

Synthesis and characterization of polybenzimidazole/α‐zirconium phosphate composites as proton exchange membrane

To improve the high‐temperature performance of proton exchange membranes, the polybenzimidazole (PBI)/α‐zirconium phosphate (α‐Zr(HPO₄)₂·nH₂O, α‐ZrP) proton exchange composite membranes were prepared in this study. PBI polymer containing a large amount of ether units has been synthesized from 3,3′‐ diaminobenzidine (DAB) and 4,4′‐oxybis (benzoic acid) by a direct polycondensation in polyphosphoric acid. The polymer exhibited a good solubility in most polar solvents. Inorganic proton conductor α‐ZrP nanoparticles have been obtained using a synthesis route involving separate nucleation and aging steps (SNAS). The effects of α‐ZrP doping content on the composite membrane performance were investigated. It was found that the introduction of ZrP improved the thermal stability of the composite membranes. The PBI/ZrP composite membranes exhibited excellent mechanical strength. The composite membrane with 10 wt% ZrP showed the highest proton conductivity of 0.192 S cm^?1 at 160°C under anhydrous condition. The proton conducting mechanism of the PBI/ZrP composite membranes was proposed to explain the proton transport phenomena. The experimental results suggested that the PBI/ZrP composite membranes may be a promising polymer electrolyte used in high temperature proton exchange membrane fuel cells (HT‐PEMFCs) under anhydrous condition. POLYM. ENG. SCI., 56:622–628, 2016. © 2016 Society of Plastics Engineers     

Sulfonated graphene oxide‐doped proton conductive membranes based on polymer blends of highly sulfonated poly(ether ether ketone) and sulfonated polybenzimidazole

Simultaneously improving the proton conductivity and mechanical properties of a polymer electrolyte membrane is a considerable challenge in commercializing proton exchange membrane fuel cells. In response, we prepared a new series of miscible polymer blends and thus the corresponding crosslinked membranes based on highly sulfonated poly(ether ether ketone) and sulfonated polybenzimidazole. The blended membranes showed more compact structures, due to the acid‐base interactions between the two constituents, and improved mechanical and morphological properties. Further efforts by doping sulfonated graphene oxide (s‐GO) forming composite membranes led to not only significantly elevated proton conductivity and electrochemical performance, but also better mechanical properties. Notably, the composite membrane with the filler content of 15 wt % exhibited a proton conductivity of 0.217 S cm^?1 at 80 °C, and its maximum power density tested by the H₂/air single PEMFC cell at room temperature reached 171 mW cm^?2, almost two and half folds compared with that of the native membrane. As a result, these polymeric membranes provided new options as proton exchange membranes for fuel‐cell applications. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46547.     

High Molecular Weight Polybenzimidazole Membranes for High Temperature PEMFC

High temperature operation of proton exchange membrane fuel cells under ambient pressure has been achieved by using phosphoric acid doped polybenzimidazole (PBI) membranes. To optimize the membrane and fuel cells, high performance polymers were synthesized of molecular weights from 30 to 94 kDa with good solubility in organic solvents. Membranes fabricated from the polymers were systematically characterized in terms of oxidative stability, acid doping and swelling, conductivity, mechanical strength and fuel cell performance and durability. With increased molecular weights the polymer membranes showed enhanced chemical stability towards radical attacks under the Fenton test, reduced volume swelling upon the acid doping and improved mechanical strength at acid doping levels of as high as about 11 mol H₃PO₄ per molar repeat polymer unit. The PBI‐78kDa/10.8PA membrane, for example, exhibited tensile strength of 30.3 MPa at room temperature or 7.3 MPa at 130 °C and a proton conductivity of 0.14 S cm^–1 at 160 °C. Fuel cell tests with H₂ and air at 160 °C showed high open circuit voltage, power density and a low degradation rate of 1.5 μV h^–1 at a constant load of 300 mA cm^–2.     

Phosphonic acid functionalized siloxane crosslinked with 3‐glycidoxyproyltrimethoxysilane grafted polybenzimidazole high temperature proton exchange membranes

Phosphonic acid functionalized siloxane crosslinked with 3‐glycidoxypropyltrimethoxysilane (GPTMS) grafted polybenzimidazole (PBI) membranes are prepared by sol–gel process. The structure of the membranes is characterized by Fourier‐transform infrared spectroscopy and X‐ray diffraction spectroscopy. SEM images of the membranes show that the membranes are homogeneous and compact. The crosslinked membranes exhibit excellent thermal stability, chemical stability and mechanical property. The proton conductivity of the crosslinked membranes increases by an order of magnitude over range of 20 °C to 160 °C under anhydrous condition, which can reach 3.15 × 10^?2 S cm^?1 at 160 °C under anhydrous condition. The activation energy of proton conductivity for membranes decreases with increase of PBI, because the formation of hydrogen bond network between the phosphonic acid and the imidazole ring can enhance the continuity of hydrogen bond in the membrane. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44818.     

Recent advances in polybenzimidazole/phosphoric acid membranes for high‐temperature fuel cells

Proton exchange membrane fuel cells are one of the most promising technologies for sustainable power generation in the future. In particular, high‐temperature proton exchange membrane fuel cells (HT‐PEMFCs) offer several advantages such as increased kinetics, reduced catalyst poisoning and better heat management. One of the essential components of a HT‐PEMFC is the proton exchange membrane, which has to possess good proton conductivity as well as stability and durability at the required operating temperatures. Amongst the various membrane candidates, phosphoric acid‐impregnated polybenzimidazole‐type polymer membranes (PBI/PA) are considered the most mature and some of the most promising, providing the necessary characteristics for good performance in HT‐PEMFCs. This review aims to examine the recent advances made in the understanding and fabrication of PBI/PA membranes, and offers a perspective on the future and prospects of deployment of this technology in the fuel cell market. © 2014 Society of Chemical Industry     

Novel proton conducting membranes based on copolymers containing hydroxylated poly(ether ether ketone) and sulfonated polystyrenes

A novel series of hydrocarbon‐based copolymers containing flexible alkylsulfonated groups and hydroxylated poly(ether ether ketone) backbones was designed and prepared as proton conducting membranes. Among the membranes, the membrane SPO₃–(PMS–PSBOS)₂ with the ion exchange capacity 1.70 showed good proton conductivity at 0.137 S/cm at 80 °C, which was two times as much as that of the control membrane SPO. Further, incorporating the sulfonated graphene oxide (s‐GO) into SPO₃–(PMS‐PSBOS)₂ leads to the composite membrane SPO₃–(PMS–PSBOS)₂–SGO, which exhibited higher proton conductivity compared to Nation 117 and the native membrane SPO₃–(PMS–PSBOS)₂. In addition, the composite membrane SPO₃–(PMS–PSBOS)₂–SGO showed well‐defined phase separated structures and high selectivity (1.40 × 10⁵ Ss/cm³), which were about three times as that of Nafion 117 (0.52 × 10⁵ Ss/cm³). These results suggested that these membranes are promising materials for direct methanol fuel cell (DMFC) applications. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45205.     

Preparation of polysiloxane phosphonic acid doped polybenzimidazole high‐temperature proton‐exchange membrane

Polysiloxane phosphonic acid doped polybenzimidazole (PBI) high‐temperature membranes were fabricated in this study. Polysiloxane phosphonic acid instead of phosphoric acid was used as a proton conductor to prevent acid from leaking. The membrane samples with different amounts of PBI were prepared and characterized with respect to the structure, thermal properties, oxidative stability, proton conductivity, and mechanical properties. The Fourier transform infrared results show that hydrogen bonds formed between PBI and polysiloxane phosphonic acid. Thermal analysis confirmed that the temperature at which membrane experienced 10% weight loss was above 230°C. None of the membrane samples broke into pieces after Fenton reagent testing. The proton conductivity of the membrane samples with 5% PBI was up to 0.034 S/cm at 140°C under nominally anhydrous conditions. The tensile strength of the membrane samples with 10% PBI was 18.3 MPa. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42956.     

Methanol permeability and proton conductivity of polybenzimidazole and sulfonated polybenzimidazole

The preparation of sulfonated polybenzimidazole (sPBI) by the grafting of (4‐bromomethyl) benzenesulfonate onto polybenzimidazole (PBI) has been investigated. The methanol permeability and proton conductivity of PBI and sPBI have been studied, and the effects of methanol concentration and temperature on the methanol permeability of PBI and sPBI membranes are discussed. The results showed that the PBI membrane is a good methanol barrier. Methanol permeability in this membrane decreases with increasing methanol concentration and increases with increasing temperature. The temperature‐dependence of methanol permeability of PBI and sPBI membranes is of the ‘Arrhenius type’. Methanol permeation of sPBI is less sensitive to temperature than that of PBI. However, sPBI is a poorer methanol barrier when compared to PBI. Methanol permeability in sPBI membranes increases with increasing methanol concentration and temperature. The proton conductivity of sPBI is 4.69 × 10^?4 S cm^?1 at room temperature in the hydrated state. The DC conductivity of sPBI–H₃PO₄ increases with increasing temperature. Proton transport in sPBI–H₃PO₄ is less sensitive to temperature than that in PBI–H₃PO₄. Copyright © 2004 Society of Chemical Industry     

Novel crosslinked AB‐type polyphenylquinoxaline membranes for high‐temperature proton exchange membrane fuel cells

AB‐type polyphenylquinoxaline (ABPPQ) membranes exhibit great mechanical properties and thermal properties for high‐temperature proton exchange membranes (PEMs). However, they dissolve in high‐concentration phosphoric acid (PA) during acid doping. In order to improve the PA resistant of ABPPQ, crosslinked ABPPQ membranes were prepared using sulfuric acid. The crosslinked ABPPQ membranes showed high PA resistance. The acid content of PA‐doped membranes decreased slightly with crosslinking, but the crosslinked polyphenylquinoxaline (CPPQ)‐20 membrane could reach 2.5 × 10^?2 S/cm proton conductivity at 160°C. Membrane electrode assemblies were fabricated with an active area of 4 cm² and Pt loading of 1 mg/cm². A startup and shutdown test (operated at 150°C with 0.2 A/cm² for 12 h and then 12 h off at room temperature) and a 30‐day long‐term durability test (150°C with 0.2 A/cm²) were conducted. In the startup and shutdown test, the crosslinked membranes showed a low open‐circuit voltage decay rate of 0.15 mV/h. In the 30‐day long‐term durability test, the voltage decay rate was 0.039 mV/h. In both tests, the crosslinked membranes showed a stable performance. Therefore, the crosslinked ABPPQ membranes can be regarded as a novel material for high‐temperature PEM fuel cells. POLYM. ENG. SCI., 59:2169–2173, 2019. © 2019 Society of Plastics Engineers     

High Polymer Content 2,5‐Pyridine‐Polybenzimidazole Copolymer Membranes with Improved Compressive Properties

Three series of polybenzimidazole (PBI) random copolymers (2,5‐pyridine‐r‐meta‐PBI, 2,5‐pyridine‐r‐para‐PBI, and 2,5‐pyridine‐r‐2OH‐PBI) were synthesized and cast into phosphoric acid (PA) doped membranes using the PolyPhosphoric Acid (PPA) Process. Copolymer composition was adjusted using co‐monomers that impart high and low solubility characteristics to simultaneously control overall copolymer solubility and gel membrane stability. Measured under a static compressive force at 180 °C, copolymer membranes generally exhibited decreased creep compliance with increasing polymer content. Within each series of copolymer membranes, increasing polymer contents proportionally reduced the phosphoric acid/polymer repeat unit (PA/PRU) ratios and their respective proton conductivities. Some copolymer membranes exhibited comparable fuel cell performances (up to 0.66 V at 0.2 A cm⁻² following break‐in) to para‐PBI (0.68 V at 0.2 A cm⁻²) and equal to 3,5‐pyridine‐based high solids membranes. Furthermore, 2,5‐pyridine copolymer membranes maintained a consistent fuel cell voltage of >0.6 V at 0.2 A cm⁻² for over 8600 h under steady‐state operation conditions. Phosphoric acid loss was monitored during long‐term studies and demonstrated acid losses as low as 5.55 ng cm⁻² h⁻¹. The high‐temperature creep resistance and long‐term operational stabilities of the 2,5‐pyridine copolymer membranes suggest that they are excellent candidates for use in extended lifetime electrochemical applications.     

A new anhydrous proton conductor based on polybenzimidazole and tridecyl phosphate

Most of the anhydrous proton conducting membranes are based on inorganic or partially inorganic materials, like SrCeO₃ membranes or polybenzimidazole (PBI)/H₃PO₄ composite membranes. In present work, a new kind of anhydrous proton conducting membrane based on fully organic components of PBI and tridecyl phosphate (TP) was prepared. The interaction between PBI and TP is discussed. The temperature dependence of the proton conductivity of the composite membranes can be modeled by an Arrhenius relation. Thermogravimetric analysis (TGA) illustrates that these composite membranes are chemically stable up to 145 °C. The weight loss appearing at 145 °C is attributed to the selfcondensation of phosphate, which results in the proton conductivity drop of the membranes occurring at the same temperature. The DC conductivity of the composite membranes can reach ∼10⁻⁴ S/cm for PBI/1.8TP at 140 °C and increases with increasing TP content. The proton conductivity of PBI/TP and PBI/H₃PO₄ composite membranes is compared. The former have higher proton conductivity, however, the proton conductivity of the PBI/H₃PO₄ membranes increases with temperature more significantly. Compared with PBI/H₃PO₄ membranes, the migration stability of TP in PBI/TP membranes is improved significantly.     

Proton Conducting Membranes Based on Poly(2,2′‐imidazole‐5,5′‐bibenzimidazole)

Poly(2,2′‐imidazole‐5,5′‐bibenzimidazole) (PBI‐imi) was synthesized via the polycondensation between 3,3′,4,4′‐tetraaminobiphenyl and 4,5‐imidazole‐dicarboxylic acid. Effects of the reaction conditions on the intrinsic viscosity of the synthesized polymers were studied. The results show that the molecular weight of the polymers increases with increasing monomer concentration and reaction time, and then levels off. With higher reaction temperature, the molecular weight of the polymer is higher. With the additional imidazole group in the backbone, PBI‐imi shows improved phosphoric acid doping ability, as well as a little higher proton conductivity when compared with widely used poly[2,2′‐(m‐phenylene)‐5,5′‐bibenzimidazole] (PBI‐ph).Whereas, PBI‐imi and PBI‐ph have the similar chemical oxidation stability. PBI‐imi/3.0 H₃PO₄ composite membranes exhibit a proton conductivity as high as 10^–4 S cm^–1 at 150 °C under anhydrous condition. The temperature dependence of proton conductivity of acid doped PBI‐imi can be modeled by an Arrhenius equation.     

Dielectric relaxations in phosphoric acid‐doped poly(2,5‐benzimidazole) and its composite membranes

Poly(2,5‐benzimidazole) (ABPBI)—a promising high‐temperature polymer electrolyte membrane—is characterized over a wide range of temperature (?50 to 220 °C) using broadband dielectric spectroscopy (BDS) to understand the various relaxation processes. The undoped ABPBI membrane shows two major secondary relaxations and a primary α relaxation. The effect of phosphoric acid (PA) and phosphotungstic acid grafted zirconium dioxide (PWA/ZrO₂) nanoparticles on the chain relaxation and the proton conductivity is investigated. The phosphoric acid alters the relaxation trends, increases the number of free ions in the polymer matrix, and therefore the conductivity. The shift in the peak frequencies of different chain relaxation processes in the presence of PA and PWA/ZrO₂ is attributed to the increase in free volume and the consequent easy motion of the polymer chains. The Fourier transform infra‐red (FTIR) spectroscopy of ABPBI and the acid‐doped composites show all the relevant peaks corresponding to C?C, C?N stretching, and phosphoric acid/phosphates, confirming the formation of ABPBI and doping with PA. The proton conductivity of the membranes is estimated from electrochemical impedance spectroscopy (EIS). To establish the effect of change in crystallinity on relaxations and proton conductivity, the undoped and PA‐doped membranes are characterized using thermogravimetric analysis and in situ XRD at high temperatures. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44867.     

Studies on proton conductivity of acid doped polybenzimidazole/polyimide and polybenzimidazole/polyvinylpyrrolidone blends

Polybenzimidazole (PBI)/polyimide (PI) and PBI/polyvinylpyrrolidone (PVP) blends were prepared. All of these polymers are suitable for acid doping as a matrix because of the existence of the N‐heterocycle in the polymers, which can eventually be used as proton conductors. The miscibility of PBI/PVP blend is confirmed by Fourier transform infrared spectroscopy (FTIR) and atomic force microscopy (AFM), while the miscibility of PBI/PI is already reported in references. Temperature dependence of proton conductivity of acid doped PBI/PI and PBI/PVP blends are studied. As the temperature increases, proton conductivity of H₃PO₄ doped PBI/PVP blends increases. Temperature dependence of proton conductivity of the blends can still be fitted by a simple Arrhenius relation. The proton transport of the blend is similar to that of PBI. The methanol permeability of PBI/PI blends is also studied. Methanol permeability in PBI/PI, PI, and PBI membranes decreases with increasing methanol concentration. POLYM. ENG. SCI., 45:1395–1400, 2005. © 2005 Society of Plastics Engineers