Inhibition of the thermal degradation of rigid poly(vinyl chloride) using poly(N‐[4‐(N′‐phenyl amino carbonyl)phenyl]maleimide)

Poly(N‐[4‐(N′‐phenyl amino carbonyl)phenyl]maleimide), poly(PhPM), has been investigated for the inhibition of the thermal degradation of rigid poly(vinyl chloride) (PVC) in air, at 180°C. Its stabilizing efficiency was evaluated by measuring the length of the induction period, the period during which no detectable amounts of hydrogen chloride gas could be observed, and also from the rate of dehydrochlorination as measured by continuous potentiometric determination, and the extent of discoloration of the degraded polymer. The results have proved the greater stabilizing efficiency of poly(PhPM) relative to that of the DBLC commercial stabilizer. This is well demonstrated by the longer induction period values and by the lower rates both of dehydrochlorination and discoloration of the polymer during degradation relative to those of the DBLC reference stabilizer. The greater stabilizing efficiency of the poly(PhPM) is most probably attributed not only to its possession of various centers of reactivity that can act as traps for radical species resulting during the degradation process, and replacement of labile chlorine atoms on PVC chains by relatively more thermally stable poly(PhPM) moieties, but also due to the ability of its fragmentation products to react with the evolved hydrogen chloride gas. A radical mechanism is suggested to account for the stabilizing action of this polymeric stabilizer. A synergistic effect is achieved when the poly(PhPM) was blended in various weight ratios with DBLC. This synergism attains its maximum when poly(PhPM) and DBLC are taken at 3 : 1 weight ratio. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Preparation of chlorinated poly(vinyl chloride)‐g‐poly(N‐vinyl‐2‐pyrrolidinone) membranes and their water permeation properties

Chlorinated poly(vinyl chloride) (CPVC) membranes for microfiltration processes were prepared with the combined process of a solvent evaporation technique and the water‐vapor induced‐phase‐inversion method. CPVC membranes with a mean pore size of 0.7 μm were very hydrophobic. These membranes were subjected to surface modification by ultraviolet (UV)‐assisted graft polymerization with N‐vinyl‐2‐pyrrolidinone (NVP) to increase their surface wettability and decrease their adsorptive fouling. The grafting yields of the modified membranes were controlled by alteration of UV irradiation time and NVP monomer concentration. The changes in chemical structure between the CPVC membrane and the CPVC‐g‐poly(N‐vinyl‐2‐pyrrolidinone) membrane and the variation of the topologies of the modified PVC membranes were characterized by Fourier transform infrared spectroscopy, gel permeation chromatography, and field emission scanning electron microscopy. According to the results, the graft yield of the modified CPVC membrane reached a maximum at 5 min of UV exposure time and 20 vol % NVP concentration. The filtration behavior of these membranes was investigated with deionized water by a crossflow filtration measurement. The surface hydrophilicity and roughness were easily changed by the grafting of NVP on the surface of the CPVC membrane through a simultaneous irradiation grafting method by UV irradiation. To confirm the effect of grafting for filtration, we compared the unmodified and modified CPVC membranes with respect to their deionized water permeation by using crossflow filtration methods. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 3188–3195, 2003     

Poly(acrylic acid)–poly(vinyl alcohol) copolymers with superabsorbent properties

Biodegradable polyacrylates were produced by a series of novel copolymerization and/or crosslinking techniques using poly(vinyl alcohol) (PVA) moieties modified by the incorporation of olefinic structures. PVA was modified by a tosylation and/or detosylation reaction. The functionalized PVA was copolymerized and/or crosslinked with acrylic acid or its partially neutralized form to give crosslinked polyacrylates that could swell in water. Their swelling behavior was determined under load. Degradation studies were performed in α-chymotrypsin, trypsin, and papain solutions. © 1998 John Wiley & Sons, Inc. J. Appl. Polym. Sci. 70: 817–829, 1998     

Thermal and spectroscopic studies of poly(N‐vinyl pyrrolidone)/poly(vinyl alcohol) blend films

Poly(N‐vinyl pyrrolidone) (PVP) and poly (vinyl alcohol) (PVA) homopolymers and their blended samples with different compositions were prepared using cast technique and subjected to X‐ray diffraction (XRD) measurements, infrared (IR) spectroscopy, ultraviolet/visible spectroscopy, and thermogravimetric analysis (TGA). XRD patterns of homopolymers and their blended samples indicated that blending amorphous materials, such as PVP, with semicrystalline polymer, such as PVA, gives rise to an amorphous structure with two halo peaks at positions identical to those found in pure PVP. Identification of structure and assignments of the most evident IR ‐ absorption bands of PVP and PVA as well as their blends in the range 400–2000 cm^?1 were studied. UV–vis spectra were used to study absorption spectra and estimate the values of absorption edge, E_g, and band tail, E_e, for all samples. Making use of Coats‐Redfern relation, thermogravimetric (TG) data allowed the calculation of the values of some thermodynamic parameters, such as activation energy E, entropy ΔS^#, enthalpy ΔH, and free energy of activation ΔG^# for different decomposition steps in the samples under investigation. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Novel Poly(vinyl alcohol)‐tetraethoxysilane hybrid matrix membranes as oxygen barriers

Novel type of membranes based on poly(vinyl alcohol) crosslinked with tetraethoxysilane have been prepared by solution casting and solvent‐evaporation method. The membranes thus formed were characterized by Fourier transform infrared spectroscopy (FTIR) to study the chemical interactions, X‐ray diffraction (XRD), and thermogravimetry (TGA) to investigate morphological and thermal properties. Membranes were prepared in two different thicknesses (30 and 55 μm) and used for measuring the oxygen permeability under varying feed pressures (maintaining the desired pressure differential across the membrane) in the range from 1 to 50 kg/cm² pressure. Oxygen permeability of the membranes ranged from 0.0091 to 1.6165 Barrer for 30 μm and 0.0305 to 0.1409 Barrer for 55‐μm thick membranes by increasing the feed pressures on the feed side. Except at 50 kg/cm² pressure, the observed oxygen permeability values are almost close to total permeability. Membranes of this study could be useful as oxygen barriers for applications in food packaging industries. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 273–278, 2007     

Preparation and characterization of interpenetrating network beads of poly(vinyl alcohol)‐grafted‐poly(acrylamide) with sodium alginate and their controlled release characteristics for cypermethrin pesticide

Interpenetrating network polymeric beads of poly(vinyl alcohol)‐grafted‐acrylamide with sodium alginate have been prepared by crosslinking with glutaraldehyde. Cypermethrin, a widely used pesticide, was loaded with 80% efficiency in these hydrogel beads. The beads were characterized by Fourier transform infrared spectroscopy to confirm the grafting. Scanning electron microscopy was used to know the morphology of the beads. Equilibrium swelling experiments indicated that swelling of the beads decreased with an increase in crosslinking. The in vitro release studies were performed under static conditions and the release data have been fitted to an empirical relation to estimate the transport parameters. The diffusion coefficients have been calculated for the transport of pesticide through the polymeric beads using the initial time approximation method. These values showed decrease with increasing crosslinking as well as increasing pesticide loading. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 552–560, 2002; DOI 10.1002/app.10306     

Synthesis of poly(vinyl alcohol)‐graft‐poly(ε‐caprolactone) and poly(vinyl alcohol)‐graft‐poly(lactide) in melt with magnesium hydride as catalyst

Grafting of poly(ε‐caprolactone) (PCL) and poly(lactide) (PLA) chains on poly(vinyl alcohol) backbone (PVA degree of hydrolysis 99%) was investigated using MgH₂ environmental catalyst and melt‐grown ring‐opening polymerization (ROP) of ε‐caprolactone (CL) and L ‐lactide (LA), that avoiding undesirable toxic catalyst and solvent. The ability of MgH₂ as catalyst as well as yield of reaction were discussed according to various PVA/CL/MgH₂ and PVA/LA/MgH₂ ratio. PVA‐g‐PCL and PVA‐g‐PLA were characterized by ¹H‐ and ¹³C‐NMR, DSC, SEC, IR. For graft copolymers easily soluble in tetrahydrofuran (THF) or chloroform, wettability and surface energy of cast film varied in relation with the length and number of hydrophobic chains. Aqueous solution of micelle‐like particles was realized by dissolution in THF then addition of water. Critical micelle concentration (CMC) decreased with hydrophobic chains. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Preparation and characterization of poly(vinyl chloride)‐graft‐acrylic acid membrane by electron beam

Poly(vinyl chloride) (PVC) was irradiated by electron beam in vacuum at 20 KGy to produce living free radicals, and then reacted with acrylic acid (AA) in solution to obtain the PVC‐g‐AA copolymers. The copolymers were characterized by Fourier transform infrared spectroscopy. Porous membranes were prepared from copolymers by the phase inversion technique. The morphology of PVC‐g‐AA membranes was studied by field emission scanning electron microscopy. The mean pore size and pore size distribution were determined by a mercury porosimeter. The mean pore size was 0.19 μm, and the bulk porosity was 56.02%. The apparent static water contact angle was 89.0°. The water drop penetration rate was 2.35 times to the original membrane. The maximum stress was 4.10 MPa. Filtration experiments were carried out to evaluate the fouling resistance of the PVC‐g‐AA membrane. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Plasma‐modified poly(vinyl alcohol) membranes for the dehydrationof ethanol

Non‐porous poly(vinyl alcohol) (PVA) membranes prepared by a cast‐evaporating technique were covered with an allyl alcohol or acrylic acid plasma‐polymerized layer. The wettability and the surface energy, as well as the chemical nature of the deposit, were assigned by X‐ray photoelectron spectroscopy (XPS) and Fourier‐transform infrared spectroscopy (FTIR). The ability of the modified membranes for dehydrating the water/ethanol azeotropic mixture by pervaporation was studied at 25, 40 and 60 °C. The best selectivity (α = 250 at 25 °C) was obtained in the case of the allyl alcohol plasma treatment. The results obtained are discussed on the basis of the hydrophilicity as well as in terms of the weakly crosslinked superficial layer that favoured the membrane swelling. Copyright © 2003 Society of Chemical Industry     

Preparation of Cu(II)‐chelated poly(vinyl alcohol) nanofibrous membranes for catalase immobilization

Poly(vinyl alcohol) (PVA) nanofibers were formed by electrospinning. Metal chelated nanofibrous membranes were prepared by reaction between Cu(II) solution and nanofibers, and which were used as the matrix for catalases immobilization. The constants of Cu(II) adsorption and properties of immobilized catalases were studied in this work. The Cu(II) concentration was determined by atomic absorption spectrophotometer (AAS), the immobilized enzymes were confirmed by the Fourier transform infrared spectroscopy (FTIR), and the amounts of immobilized enzymes were determined by the method of Bradford on an ultraviolet spectrophotometer (UV). Adsorption of Cu(II) onto PVA nanofibers was studied by the Langmuir isothermal adsorption model. The maximum amount of coordinated Cu(II) (q_m) was 2.1 mmol g⁻¹ (dry fiber), and the binding constant (K_l) was 0.1166 L mmol⁻¹. The immobilized catalases showed better resistance to pH and temperature inactivation than that of free form, and the thermal and storage stabilities of immobilized catalases were higher than that of free catalases. Kinetic parameters were analyzed for both immobilized and free catalases. The value of V_max (8425.8 μmol mg⁻¹) for the immobilized catalases was smaller than that of the free catalases (10153.6 μmol mg⁻¹), while the K_m for the immobilized catalases were larger. It was also found that the immobilized catalases had a high affinity with substrate, which demonstrated that the potential of PVA‐Cu(II) chelated nanofibrous membranes applied to enzyme immobilization and biosensors. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Thermal characteristics of interpenetrating polymer networks composed of poly(vinyl alcohol) and poly(N‐isopropylacrylamide)

Interpenetrating polymer networks (IPNs) composed of poly(vinyl alcohol) (PVA) and poly(N‐isopropylacrylamide) (PNIPAAm) were prepared by the sequential‐IPN method. The thermal characterization of the IPNs was investigated using differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and dielectric analysis (DEA). Depression of the melting temperature (T_m) of the PVA segment in IPNs was observed with increasing PNIPAAm content using DSC. DEA was employed to ascertain the glass‐transition temperature (T_g) of IPNs. From the result of DEA, IPNs exhibited two T_g values, indicating the presence of phase separation in the IPNs. The thermal decomposition of IPNs was investigated using TGA and appeared at near 200°C. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 881–885, 2003     

Poly(N‐hydroxyethyl acrylamide)‐b‐polystyrene by combination of ATRP and aminolysis processes

Block copolymers of very hydrophilic poly(N‐hydroxyethyl acrylamide) (PHEAA) with polystyrene (PS) were successfully synthesized by sequential atom transfer radical polymerization of ethyl acrylate (EA) and styrene monomers and subsequent aminolysis of the acrylic block with ethanolamine. Quantitative aminolysis of poly(ethyl acrylate) (PEA) block yielded poly(N‐hydroxyethyl acrylamide)‐b‐polystyrene in well‐defined structures, as evidenced by Fourier transform infrared spectroscopy (FTIR) and ¹H‐NMR spectroscopy techniques. Three copolymers with constant chain length of PHEAA (degree of polymerization: 80) and PS blocks with 21, 74, and 121 repeating units were prepared by this method. Among those, the block copolymer with 21 styrene repeating units showed excellent micellation behavior in water without phase inversion below 100°C, as inferred from dynamical light scattering, environmental scanning electron microscopy, and fluorescence measurements. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Development of quaternarized poly(vinyl alcohol) anion‐exchange membranes for applications in electrodialysis

The main objective of this work is the development of anionic exchange membranes for the treatment of solutions containing metallic ions using the electrodialysis process. Anionic membranes were synthesized from poly(vinyl alcohol), with the insertion of quaternary ammonium groups in the polymeric matrix and subsequent crosslinking with glutaraldehyde and maleic anhydride. Different membranes were synthesized in order to evaluate the combination of physical–chemical properties and ionic transport. The morphology and structure of the membranes were investigated by scanning electron microscopy and infrared spectroscopy. The thermal transitions and stability of all the membranes were characterized using calorimetric techniques: thermogravimetric analysis, and differential scanning calorimetry, and compared with those of the individual polymers. The physical properties (ion‐exchange capacity, water absorption, and dimensional stability) showed that the different crosslink agents used significantly affect the membrane properties. The electrodialysis performance of the membranes in the transport of chloride and nitrate ions showed that the membranes produced can be successfully used in this separation process. Selemion® AMV commercial membrane was used to compare the percentage extractions of the indicated ions with the produced membranes. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44946.     

Thermal degradation behavior of poly(vinyl chloride) in presence of poly(N‐acryloyl‐N′‐cyanoacetohydrazide)

The thermal degradation behavior of poly (vinyl chloride), PVC, in presence of poly(N‐acryloyl‐N′‐cyanoacetohydrazide), PACAH, has been studied using continuous potentiometric determination of the evolved HCl gas from the degradation process from one hand and by measuring the extent of discoloration of the degraded samples from the other. The efficiency of blending PACAH with dibasic lead carbonate, DBLC, conventional thermal stabilizer has also been investigated. A probable radical mechanism for the effect of PACAH on the thermal stabilization of PVC has been proposed. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Gas permeation through water‐swollen polysaccharide/poly(vinyl alcohol) membranes

The effect of Na‐alginate content on the gas permeation properties of water‐swollen membranes prepared by varying Na‐alginate and poly(vinyl alcohol) (PVA) content in membranes was investigated. The influences of water content and crystallinity of the membranes on the gas permeation performance of the water‐swollen membranes were studied. The gas permeation rate and selectivity of Na‐alginate/PVA water‐swollen membranes were compared with those of the dry membranes. The permeation rates of nitrogen and carbon dioxide through water‐swollen membranes were in the range of 0.4–7.6 × 10^?7 to 3.7–8.5 × 10^?6 cm³ (STP)/cm² s^?1 cmHg^?1, which were 10,000 times higher than those of dry‐state membranes. The permeation rates of mixture gases through water‐swollen Na‐alginate/PVA membranes were found to increase exponentially with the increase of Na‐alginate content, whereas carbon dioxide concentration in permeates was decreased linearly. It was found that the gas permeance of the water‐swollen membranes increased with increasing the Na‐alginate content in the membrane. Gas permeation rates of the water‐swollen Na‐alginate/PVA membranes increased with increasing the water content in the membrane and decreasing the crystallinity of the membrane. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3225–3232, 2004     

Preparation and characterization of poly(vinyl alcohol)‐poly(vinyl pyrrolidone) blend: A biomaterial with latent medical applications

Aqueous solutions of poly(vinyl alcohol) and poly(vinyl pyrrolidone) are blended and films are produced by casting method with the further intention of being used as bio‐materials with latent medical application. Glutaraldehyde, 4,4′‐diazido‐2,2′‐stilbenedisulfonic acid disodium salt tetra‐hydrate are used as crosslinker agents, whereas lactic acid is the plasticizer in the blend. The obtained films are characterized by differential scanning calorimetry (DSC), mechanical properties, swelling and solubility behavior. DSC measurements show that the blends exhibit a single glass transition temperature indicating that they are miscible, even in the presence of the plasticizer and crosslinker agents. By the combination of all mentioned additives, a relevant enhancement of the swelling is observed, accompanied by a stabilization of the solubility during the tested time. Finally, mechanical properties show an appropriate performance in the studied parameters. As a consequence, the obtained films could be suitable for use as medium or long‐term implants. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Structure‐property and swelling behavior of electron beam irradiated poly(vinyl alcohol)/acrylamide/sodium montmorillonite clay composites

Composites based on poly(vinyl alcohol) (PVA), acrylamide monomer (AM) and sodium montmorillonite clay (MMT) were prepared, in the form of thin films, by solution casting. The PVA/AM/MMT composites films were then exposed to electron beam irradiation to form crosslinked network structure. The structure‐property behavior of PVA/AM/MMT hybrids was demonstrated by x‐ray diffraction (XRD), scanning electron microscopy, gel content, color intensity, thermogravimetric analysis (TGA) and swelling behavior in aqueous solutions. The results indicated that the introduction of MMT clay ratio up to 5% decreased the gel content of PVA/AM hydrogels. The color measurements indicated that the introduction of MMT clay ratio up to 5% was shown to affect the color intensity of composite films. It was found that both PVA/AM hydrogels and PVA/AM/MMT composites reached the equilibrium swelling state in water after four hours; however PVA/AM/MMT composites displayed higher swelling than PVA/AM hydrogels. However, the swelling of PVA/AM hydrogels or their composites at the equilibrium state increased with increasing temperature up to 60°C. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Physical properties of poly(vinyl chloride)–grafted N‐isopropylacrylamide graft copolymers and corresponding polyblends

The physical properties of poly(vinyl chloride) (PVC) and poly(N‐isopropylacrylamide) [poly(NIPAAm)] blend systems, and their corresponding graft copolymers such as PVC‐g‐NIPAAm, were investigated in this work. The compatible range for PVC–poly(NIPAAm) blend systems is less than 15 wt % poly(NIPAAm). The water absorbencies for the grafted films increase with increase in graft percentage. The water absorbencies for the blend systems increase with increase in poly(NIPAAm) content within the compatible range for the blends, but the absorbencies decrease when the amount of poly(NIPAAm) is more than the compatible range in the blend system. The tensile strengths for the graft copolymers are larger than the corresponding blends. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 170–178, 2000     

Miscibility and phase structure of binary blends of poly(L‐lactide) and poly(vinyl alcohol)

Blend films of poly(L ‐lactide) (PLLA) and poly(vinyl alcohol) (PVA) were obtained by evaporation of hexafluoroisopropanol solutions of both components. The component interaction, crystallization behavior, and miscibility of these blends were studied by solid‐state NMR and other conventional methods, such as Fourier transform infrared (FTIR) spectra, differential scanning calorimetry (DSC), and wide‐angle X‐ray diffraction (WAXD). The existence of two series of isolated and constant glass‐transition temperatures (T_g's) independent of the blend composition indicates that PLLA and PVA are immiscible in the amorphous region. However, the DSC data still demonstrates that some degree of compatibility related to blend composition exists in both PLLA/atactic‐PVA (a‐PVA) and PLLA/syndiotactic‐PVA (s‐PVA) blend systems. Furthermore, the formation of interpolymer hydrogen bonding in the amorphous region, which is regarded as the driving force leading to some degree of component compatibility in these immiscible systems, is confirmed by FTIR and further analyzed by ¹³C solid‐state NMR analyses, especially for the blends with low PLLA contents. Although the crystallization kinetics of one component (especially PVA) were affected by another component, WAXD measurement shows that these blends still possess two isolated crystalline PLLA and PVA phases other than the so‐called cocrystalline phase. ¹³C solid‐state NMR analysis excludes the interpolymer hydrogen bonding in the crystalline region. The mechanical properties (tensile strength and elongation at break) of blend films are consistent with the immiscible but somewhat compatible nature of these blends. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 762–772, 2001     

Preparation and characterizaton of poly(dimethyl amino ethyl methacrylate) modified poly(vinyl alcohol) membrane by UV radiation for the permeation of 5‐fluorouracil

Poly(vinyl alcohol) was modified by UV radiation with dimethyl amino ethyl methacrylate (DMAEMA) monomer to get poly(dimethyl amino ethyl methacrylate) modified poly(vinyl alcohol) (PVADMAEMA) membrane. The PVADMAEMA membranes were characterized by Fourier transform infrared spectroscopy. The tensile strength and elongation of PVADMAEMA membranes were measured by Universal Testing Machine. The results of X‐ray diffraction (XRD) and differential scanning calorimetry (DSC) showed that (1) the crystalline area in PVADMAEMA decreased with increasing the content of poly(dimethyl amino ethyl methacrylate) in the membrane. (2) Only one glass transition temperature (T_g) was found for the various PVADMAEMA membranes. It means that poly(dimethyl amino ethyl methacrylate) and PVA are compatible in PVADMAEMA membrane. (3)The T_g of the membrane is reduced with increasing the content of poly(dimethyl amino ethyl methacrylate) in the membrane. The water content on the PVADMAEMA membranes was determined. It was found that the water content on the PVADMAEMA membrane increased with increasing the content of poly(dimethyl amino ethyl methacrylate). The changes of properties enhanced the permeability of 5‐Fluorouracil (5‐Fu) through the PVADMAEMA membranes. A linear relationship between the permeability and the weight percent of poly(dimethyl amino ethyl methacrylate) in the PVADMAEMA membrane is found. It is expressed as P (cm/s) = (9.6 ± 0.4) × 10^?5 + (8.8 ± 0.6) × 10^?5 W _x , where P is the permeability of 5‐Fu through the membrane and W_x is the weight percent of poly(dimethyl amino ethyl methacrylate) in the PVADMAEMA membrane. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012