Electrical properties of sorbitol‐doped poly(vinyl alcohol)–poly(acrylamide‐co‐acrylic acid) polymer membranes

Solid polymer membranes from poly(vinyl alcohol) (PVA) and poly(acrylamide‐co‐acrylic acid) (PAA) with varying doping ratios of sorbitol were prepared using the solution casting method. The films were examined with Fourier transform infrared spectroscopy, thermogravimetric analysis, differential scanning calorimetry, and AC impedance spectroscopy. The impedance measurements showed that the ionic conductivity of PVA–PAA polymer membrane can be controlled by controlled doping of sorbitol within the polymer blends. The PVA–PAA–sorbitol membranes were found to exhibit excellent thermal properties and were stable for a wide temperature range (398–563K), which creates a possibility of using them as suitable polymers for device applications. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Enhanced thermoelectric properties of poly(3,4-ethylenedioxythiophene): Poly(styrenesulfonate)/copper phthalocyanine disulfonic acid composite films

A series of poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate)/copper phthalocyanine disulfonic acid (PEDOT: PSS/CuPc-[SO₃H]₂) composite films were prepared by using CuPc-(SO₃H)₂ as the dopant. EG treatment was applied to further improve the thermoelectric properties of PEDOT: PSS/CuPc-(SO₃H)₂ composites. Structural analyses indicated the strong π − π interactions existed between PEDOT: PSS and CuPc-(SO₃H)₂, and led to more ordered regions in the composite films, and benefit the conductivity. CuPc-(SO₃H)₂ can greatly improve the thermoelectric properties of PEDOT: PSS/CuPc-(SO₃H)₂ composite films, which have a Seebeck coefficient of 13.2 μV K⁻¹ and a conductivity of 2.8 × 10⁵ S/m with 20 wt% CuPc-(SO₃H)₂ at room temperature, and the corresponding power factor is 48.8 μW m⁻¹ K⁻², which is almost 6.83 times higher than the PEDOT: PSS films without CuPc-(SO₃H)₂.     

Anomalous behavior of the dielectric and electrical properties of polymeric nanodielectric poly(vinyl alcohol)–titanium dioxide films

The complex dielectric permittivity, alternating‐current electrical conductivity, electric modulus, and impedance spectra of polymeric nanocomposite (PNC) films consisting of a poly(vinyl alcohol) (PVA) matrix dispersed with nanosize particles of titanium dioxide (TiO₂); (i.e., PVA–x wt % TiO₂, where x is 0, 1, 3, or 5) were investigated in the frequency range 20 Hz to 1 MHz at ambient temperature. A detailed analysis of the results showed that the values of the dielectric and electrical parameters of these PNC‐based nanodielectric films varied anomalously with increasing TiO₂ concentration. The temperature‐dependent dielectric characterization of the PVA–3 wt % TiO₂ film revealed that the dielectric polarization at a fixed frequency increased nonlinearly with increasing temperature. The temperature‐dependent electric modulus relaxation time values of the nanodielectric film obeyed Arrhenius behavior. The X‐ray diffraction study confirmed that the crystalline phase of the PVA matrix decreased with increasing TiO₂ concentration; this suggested that the interaction of the TiO₂ nanoparticles caused some destruction of the hydroxyl group dipolar ordering in the hydrogen‐bonded crystalline structure of the pristine PVA matrix. The intensities of the diffraction peaks of the TiO₂ nanofiller were enhanced as its concentration increased in these nanodielectrics; this confirmed the existence of TiO₂ nanoparticles inside the crystalline phases of the PVA matrix. The surface morphology of the films was examined by the study of their scanning electron micrographs. The feasibility of using these flexible polymeric nanodielectric films as electrical insulators and dielectric substrates in low‐power microelectronic devices operated at audio‐ and radio‐frequency electric fields was explored. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44568.     

Preparation and characterization of aqueous dispersions of poly(3,4‐ethylenedithiathiophene‐co‐3,4‐ethylenedioxythiophene)/ poly(styrene sulfonate) and their conducting films

The chemical oxidative copolymerization of 3,4‐ethylenedithiathiophene (EDTT) with 3,4‐ethylenedioxythiophene (EDOT) and 2′‐hydroxymethyl‐3,4‐ethylenedioxythiophene in a poly(styrene sulfonic acid) aqueous solution was successfully carried out to form stable, dark blue colloidal dispersions in water. Coating these dispersions onto polypropylene substrates led to the formation of free‐standing copolymer films. The mechanical, electrical, and thermoelectrical properties of these films were investigated; the films showed superior properties in comparison with those of poly(3,4‐ethylenedithiathiophene) (PEDTT)/poly(styrene sulfonate) (PSS). The copolymer film based on EDTT and EDOT achieved a high electrical conductivity (8.2 × 10^?2 S cm^?1) at 298 K; this could be improved about 10 times through the addition of dimethyl sulfoxide (DMSO) or DMSO/isopropyl alcohol into the polymer dispersion with almost constant Seebeck coefficients of about 9 μV K^?1. On the contrary, these additives had almost no effect on the conductivity of PEDTT/PSS. The structure and morphology of the polymer films were studied by X‐ray diffraction and SEM analyses. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Different properties for poly(3,4‐ethylenedioxythiophene) films derived from single or multiple polymerization steps

Films of poly(3,4‐ethylenedioxythiophene) were prepared with single and multiple electropolymerization steps, where the numbers of polymerization steps (n's) were 3, 5, and 7, with identical experimental conditions and total polymerization times (τ's). The electroactivity of the films prepared with multiple steps remained almost unaltered when n increased, with the ability of the films to store charge with n > 3 being smaller than that of the films with similar thicknesses but derived from a single electrodeposition step. In contrast, the stability of the films produced with n polymerization steps was significantly higher than that of the films derived from a single step with the same τ, with the difference between the two systems increasing with n, that is, τ used to yield the films. On the other hand, although the morphological and topological characteristics of the surface and the electrical conductivity were affected by the procedure used to produce the films, the organization of the polymer molecules in the crystalline phase, the thermal stability, and the electronic properties (ionization potential, electron affinity, and lowest π–π* transition energy) were practically identical in both cases. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effects of solvents on the morphology and conductivity of poly(3,4‐ethylenedioxythiophene):Poly(styrenesulfonate) nanofibers

In this study, the effect of solvents on the morphology and conductivity of poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate)(PEDOT:PSS) nanofibers is investigated. Conductive PEDOT:PSS nanofibers are electrospun by dissolving a fiber‐forming polymer, polyvinyl alcohol, in an aqueous dispersion of PEDOT:PSS. The conductivity of PEDOT:PSS nanofibers is enhanced 15‐fold by addition of DMSO and almost 30‐fold by addition of ethylene glycol to the spinning dopes. This improvement is attributed to the change in the conformation of the PEDOT chains from the coiled benzoid to the extended coil quinoid structure as confirmed by Raman spectroscopy, X‐ray diffraction, and differential scanning calorimetry. Scanning electron microscopy images show that less beady and more uniform fiber morphology could be obtained by incorporation of ethylene glycol in the spinning dopes. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40305.     

Enhanced thermoelectric performance by alcoholic solvents effects in highly conductive benzenesulfonate‐doped poly(3,4‐ethylenedioxythiophene)/graphene composites

Benzenesulfonate‐doped poly(3,4‐ethylenedioxythiophene) (PEDOT‐Bzs)/graphene thermoelectric (TE) composites with various graphene filler contents were synthesized in five different kinds of solvents. Dodecylbenzenesulfonic acid (DBSA) was used to achieve good dispersion of graphene into the PEDOT matrix. Among the synthesized PEDOT materials, the one synthesized in methanol (PEDOT‐MeOH) had the highest electrical conductivity. X‐ray photoelectron spectroscopy (XPS) analysis showed almost the same charge carrier concentration for all PEDOT materials. However, the X‐ray diffraction (XRD) analysis highlighted the enhancement of PEDOT chain stacking by shorter‐chain alcoholic solvents, as a result of which the carrier mobility and electrical conductivity were increased. The electrical conductivity and the Seebeck coefficient of the PEDOT/graphene composites were significantly improved with increasing the graphene content, which strongly depended on increased carrier mobility. The thermal conductivity of the composites exhibited relatively small changes, attributed to phonon scattering effects. The maximum TE efficiency of the PEDOT‐MeOH/graphene composite with 75 wt % graphene showed a substantially improved value of 1.9 × 10^?2, higher than that of the other PEDOT/graphene composites. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42107.     

Improvement in physical and electrical properties of poly(vinyl alcohol) hydrogel conductive polymer composites

With an aim to develop anti‐electrostatic discharge materials based on biodegradable polymers, poly(vinyl alcohol) films composited with two different conductive fillers (carbon black and aluminium) at various fillers contents (20?60%wt), were manufactured using solvent‐casting technique. The mechanical properties of such the films were investigated through tensile stress‐strain tests. Wettability and morphology of the composite films were performed by water contact angle measurement and SEM, respectively. Young's modulus of the composite films can be increased with the addition of conductive fillers. The surface of the composite films showed non‐homogeneous appearance, in which the phase boundary within the composites was clearly observed and the conductive fillers formed aggregation structure at high filler concentration. In addition, the composite films exhibited better hydrophobicity when higher conductive filler content was added. TGA results suggested that both carbon black and aluminum have proven their efficiency to enhance thermal stability of poly(vinyl alcohol). Investigation of cross‐cut adhesion performance of the prepared composite films revealed that carbon black‐filled composites exhibited excellent adhesion strength. The effect of conductive filler content on surface resistivity of the composite films was also examined. The experimental results confirmed that both the fillers used in this study can improve the electrical conductivity of poly(vinyl alcohol) hydrogel. The surface resistivity of the composite films was reduced by several orders of magnitude when the filler of its critical concentration was applied. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42234.     

Versatile poly(3,4‐ethylenedioxythiophene) poly(styrenesulfonate) films on polydimethylsiloxane substrates having random micro ridges: Study of resistive behaviors of a polymer–polymer laminate

Conductive polymers such as poly(3,4‐ethylenedioxythiophene) poly(styrenesulfonate) or PEDOT:PSS has become increasingly important in present day organic electronics. PEDOT:PSS being a polymer is more durable than metals used in electronics and thus offers greater mechanical flexibility during operation. This article presents results regarding resistive behaviors of blade coated PEDOT:PSS films on polydimethylsiloxane (PDMS) substrate having random micro ridges as a function of axial strain and different temperatures. The average resistance of the blade coated PEDOT:PSS films were found to increase by 1.4 times between 35 and 45% axial strain. The resistances of the films were found to change within the temperature range of 25–230°C without any thermal morphological degradations and the polymer–polymer laminate also showed linear thermal actuation behavior. These results suggest that the blade coated PEDOT:PSS films on PDMS substrates with random micro ridges can be potentially useful in versatile applications like stretchable conductors, thermal actuators, thermoelectric generators, and as heating surfaces. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41235.     

Fabrication of poly(3,4‐ethylenedioxythiophene)‐polysaccharide composites

Poly(3,4‐ethylenedioxythiophene) (PEDOT) doped with a series of anionic polysaccharides such as carboxymethyl cellulose, sodium hyaluronate, xanthan gum, pectin, gellan gum were prepared by electropolymerization in aqueous solutions. Some other dopants of potassium nitrate, potassium sulfate, sodium poly(styrenesulfonate), and sodium polyacrylate were used in comparison with the anionic polysaccharides. The electrochemical properties and stability of the obtained PEDOT films were also investigated. It was found that indium tin oxide (ITO) conductive glass could be used as the working electrode of the electropolymerization of EDOT and that the dopant had a great influence on polymerization potential and overoxidation potential. These charged biomolecules of anionic polysaccharides were found to facilitate electropolymerization of EDOT instead of common doping anions as counterion. The electroactive PEDOT films doped with anionic polysaccharides showed stable electrochemical properties, good texture, and adhesion properties to the ITO conductive glass. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Modified solution technique for preparing poly(3,4‐ethylenedioxythiophene) and a Poly(3,4‐ethylenedioxythiophene)/silver nanocomposite: Optical and thermal behavior

In this study, we prepared poly(3,4‐ethylenedioxythiophene) (PEDOT) via the chemical oxidation of the 3,4‐ethylenedioxythiophene monomer in a system consisting of miscible binary organic solvents, that is, acetonitrile (CH₃CN) and chloroform (CHCl₃). This successful technique was then used to synthesize a poly(3,4‐ethylenedioxythiophene) (PEDOT)/silver (Ag) nanocomposite as well. In this facile and efficient technique, a higher solubility of the oxidizing reagent, which originated from a relative enhancement in the polarity of the reaction medium, led to significant changes in the optical and thermal behaviors of the resulting products. To investigate the degree of validity of the technique applied, a pure sample of PEDOT (PEDOT I) was also synthesized with CHCl₃ alone, and this was then compared with a sample prepared in CH₃CN/CHCl₃ binary solvents (PEDOT II). To prepare the PEDOT/Ag nanocomposite, first the PEDOT synthesized in binary solvents was thoroughly dissolved in a dimethyl sulfoxide solvent. Next, Ag nanopowder was uniformly dispersed in the previous solution of PEDOT with sonication. The PEDOT/Ag nanocomposite was then precipitated through the addition of a methanol nonsolvent. The approximate size of nano‐Ag within the polymer matrix was found to be about 40 nm. Scanning electron microscopy images of the pure PEDOT II and PEDOT/Ag nanocomposite exhibited an agglomerated sponge and nanospherical homogeneity, respectively. In comparison with PEDOT I, considerable redshifts in the ultraviolet–visible absorption spectra of the pure PEDOT II and PEDOT/Ag nanocomposite were observed. In addition, the thermostability order was found to be PEDOT/Ag > PEDOT II > PEDOT I at all temperatures above 300°C. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 2707–2712, 2013     

Capacitance properties of graphite oxide/poly(3,4‐ethylene dioxythiophene) composites

Poly(3,4‐ethylene dioxythiophene) (PEDOT) and graphite oxide (GO)/PEDOT composites (GPTs) doped with poly(sodium styrene sulfate) (PSS) were synthesized by in situ polymerization in aqueous media. The electrochemical capacitance performances of GO, PEDOT–PSS, and GPTs as electrode materials were investigated. The GPTs had a higher specific capacitance of 108 F/g than either composite constituent (11 F/g for GO and 87 F/g for PEDOT–PSS); this was attributable to its high electrical conductivity and the layer‐within/on‐layer composite structure. Such an increase demonstrated that the synergistic combination of GO and PEDOT–PSS had advantages over the sum of the individual components. On the basis of cycle‐life tests, the capacitance retention of about 78% for the GPTs compared with that of 66% for PEDOT–PSS after 1200 cycles suggested a high cycle stability of the GPTs and its potential as an electrode material for supercapacitor applications. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Electrically conductive poly(3,4‐ethylenedioxythiophene)–polystyrene sulfonic acid/polyacrylonitrile composite fibers prepared by wet spinning

Composite conductive fibers based on poly(3,4‐ethylenedioxythiophene) (PEDOT)–polystyrene sulfonic acid (PSS) blended with polyacrylonitrile (PAN) were prepared via a conventional wet‐spinning process. The influences of the PEDOT–PSS content on the electrical conductivity, thermal stability, and mechanical properties of the composite fibers were investigated. The fibers with 1.83 wt % PEDOT–PSS showed a conductivity of 5.0 S/cm. The breaking strength of the fibers was in the range 0.36–0.60 cN/dtex. The thermal stability of the PEDOT–PSS/PAN composite fibers was similar to but slightly lower than that of the pure PAN. The X‐ray diffraction results revealed that both the pure PAN and PEDOT–PSS/PAN composite fibers were amorphous in phase, and the crystallization of the latter was lower than that of the former. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Preparation of a poly(3‐hexylthiophene)‐grafted indium tin oxide/poly(3‐hexylthiopene) composite and its conductivity–temperature characteristics

The temperature–conductivity characteristics of poly(3‐hexylthiophene) (P3HT) composites filled with P3HT‐grafted indium tin oxide (ITO) particles were investigated in this work. The ITO particles were first treated with a silane coupling reagent of 3‐aminopropyltriethoxysilane (APS), and then thiophene rings were introduced through a condensation reaction between the ending amino groups of APS and the carboxylic groups of thiophene‐3‐acetic acid. The composites were prepared by the polymerization filling of the 3‐hexylthiophene (3HT) monomer with the thiophene‐ring‐introduced ITO particles. Elemental analysis, Fourier transform infrared, and X‐ray photoelectron spectroscopy were used to confirm the grafting reaction on the ITO surface. The longer the polymerization time was or the higher the 3HT/ITO feeding ratio was, the more P3HT was grafted. The influence of the grafted amount on the electrical properties of ITO particles was attributed to the wrapping effect formed by the grafted P3HT on the surface of the ITO particles. The conductivity change of the P3HT‐grafted ITO/P3HT composites was proved to be subject to the change in the average gap width of ITO interparticles, which was determined by the filling ratio of P3HT to ITO in the polymerization and the volume expansion effect of a P3HT thin film between neighboring ITO particles during the heating process. In comparison with the ungrafted ITO/P3HT composites, the grafting treatment enhanced the interaction between the particles and polymer matrix, and this was helpful for obtaining a more homogeneous dispersion structure for the composites and thus afforded a higher positive temperature coefficient intensity and better reproducibility. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1881–1888, 2006     

Mechanically enhanced electrically conductive films from polymerization of 3,4‐ethylenedioxythiophene with wood microfibers

This study was aimed at enhancing the mechanical properties of poly(3,4‐ethylenedioxythiophene)/poly(styrene sulfonate) (PEDOT:PSS) using wood microfibers. Ultra fine friction grinding was conducted on wood particles to reduce their size to the micron scale and to induce fibrillation. Oxidative polymerization was performed on 3,4‐ethylenedioxythiophene (EDOT) monomer at seven dosages based on the content of microfibers in the formulation. The presence of PEDOT:PSS in the prepared films was verified by infrared spectroscopy and scanning electron microscopy. The composite films became stronger and stiffer as the fiber content increased. An EDOT:microfibers ratio of 33 wt % was considered the best among the seven tested levels, judging from their low sheet resistivity (340 Ω/sq.) and favorable tensile properties (38 MPa strength and 4.8 GPa stiffness). The selected films were also tested for their resistance to solvents to obtain information about their potential use in different environments. Among the tested solvents, sodium hydroxide greatly decreased the film conductivity. It also had the harshest effect on reducing the weight of the film. Findings from this study demonstrate the successful use of wood microfibers alternative to synthetic substrates and cellulose nanofiber as a supportive and reinforcing material for electrically conductive polymers. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45127.     

One-step preparation of poly(NIPAM-pyrrole) electroconductive composite hydrogel and its dielectric properties

Conductive polymers and hydrogels are two of the hot prospect polymer types that are used for new stimuli responsive materials. In this study, one-step preparation of electroconductive composite hydrogels containing polypyrrole (PPy) and N-isopropylacrylamide (NIPAM) using free radical polymerization technique was achieved with N,N-methylenebisacrylamide as a crosslinker and ammonium peroxy disulphate (APS) as initiator, in mixture of water/isopropyl alcohol. The equilibrium swelling degree of the poly(NIPAM)-pyrrole) electroconductive composite hydrogel was 9.88 g of H₂O/g dry polymer. According to TGA results, the thermal stability of the prepared composite poly(NIPAM-PPy) conductive hydrogel (700°C) hydrogel is higher than that of pure poly(NIPAM) hydrogel (600°C). Furthermore, prepared samples were characterized by FTIR, and SEM analyzes. Later, the samples were pressured into pellets so that electrical impedance spectroscopy (EIS) measurements were taken between 10 and 10 MHz at room temperature. The dielectric constant value of composite poly(NIPAM-PPy) hydrogel at 10 Hz is almost 10 times higher than that of poly(NIPAM) hydrogel. Both samples' real and imaginary parts of dielectric constant decreased with increased frequency. Samples exhibited non-Debye relaxation since experimental data fit into dielectric model of Havriliak-Negami. Moreover, low frequency data yielded d.c. conductivity of the pure and composite samples as 3.74 × 10⁻¹¹ and 1.02 × 10⁻⁸ S/cm, respectively. Real part of impedance at low frequencies also points out ~10³ times lower resistance values at 10 Hz for composite poly(NIPAM-PPy) hydrogel. Therefore, EIS results support that electroconductive composite hydrogel fabrication was achieved using free radical polymerization technique.     

Effects of the electrolyte content on the electrical permittivity,thermal stability,and optical dispersion of poly(vinyl alcohol)–cesium copper oxide–lithium perchlorate nanocomposite solid‐polymer electrolytes

Solid‐polymer electrolytes (SPEs) in the form of poly(vinyl alcohol) (PVA) doped with various amounts (5, 10, and 15 wt %) of lithium perchlorate trihydrate (LiClO₄·3H₂O) and 2 wt % cesium copper oxide (Cs₂CuO₂) nanoparticles were fabricated by a solvent intercalation method. The obtained nanocomposites were evaluated for their chemical structure and microstructural and morphological behaviors via Fourier transform infrared spectroscopy, X‐ray diffraction, and scanning electron microscopy methods, respectively. The obtained dielectric behaviors, alternating‐current conductivity, dielectric modulus, and dielectric relaxation of the SPEs depended on the volume fraction of the electrolyte. Linear behavior of the current–voltage characteristics for all of the SPE films was observed with a slight deviation at a higher voltage. The thermal behaviors of the PVA–Cs₂CuO₂–LiClO₄ films were evaluated by differential scanning calorimetry and thermogravimetric analysis. The refractive index, band‐gap energy, and optical dispersion were examined with UV–visible spectroscopy. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45852.     

Low dielectric and high thermal conductivity epoxy nanocomposites filled with NH2‐POSS/n‐BN hybrid fillers

Hybrid fillers of mono‐amine polyhedral oligomeric silsesquioxane/nanosized boron nitride (NH₂‐POSS/n‐BN) were performed to fabricate NH₂‐POSS/n‐BN/epoxy nanocomposites. Results revealed that the dielectric constant and dielectric loss values were decreased with the increasing addition of NH₂‐POSS obviously, but increased with the increasing addition of BN fillers. For a given loading of NH₂‐POSS (5 wt %), the thermal conductivities of NH₂‐POSS/n‐BN/epoxy nanocomposites were improved with the increasing addition of n‐BN fillers, and the thermal conductivity of the nanocomposites was 1.28 W/mK with 20 wt % n‐BN fillers. Meantime, the thermal stability of the NH₂‐POSS/n‐BN/epoxy nanocomposites was also increased with the increasing addition of n‐BN fillers. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41951.     

Preparation and performance of a transparent poly(3,4‐ethylene dioxythiophene)–poly(p‐styrene sulfonate‐co‐acrylic acid sodium) film with a high stability and water resistance

Poly(p‐styrene sulfonate‐co‐acrylic acid sodium) (PSA) from the copolymerization of acrylic acid sodium and p‐styrene sulfonate monomers were used to dope poly(3,4‐ethylene dioxythiophene) (PEDOT) to generate PEDOT–PSA antistatic dispersions. Compared to those of the PEDOT–poly(p‐styrene sulfonate sodium) (PSS), the physical and electrical properties of the PEDOT–PSA conductive liquids were much better. The PEDOT–PSA films possessed a better water resistance without a decrease in the conductivity. The sheet resistance of the PEDOT–PSA–poly(ethylene terephthalate) (PET) films was about 1.5 × 10⁴ Ω/sq with a 100 nm thickness, the same as the PEDOT–PSS–PET films. The transmittance of the PEDOT–PSA–PET films exceeded 88%. Furthermore, the environmental dispersity of the PEDOT–PSA antistatic dispersion was apparently improved by the dopant PSA so that the stability was extraordinarily promoted. Meanwhile, the water resistances of the PEDOT–PSA–PET and PEDOT–PSA films were also enhanced. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45163.     

Enhanced thermoelectric performance of poly(3,4‐ethylenedioxythiophene):poly(4‐styrenesulfonate) (PEDOT:PSS) with long‐term humidity stability via sequential treatment with trifluoroacetic acid

This paper reports a range of effective sequential chemical processes to enhance the thermoelectric performance of conducting poly(3,4‐ethylenedioxythiophene) films doped with poly(styrene sulfonate) anions (PEDOT:PSS). The electrical conductivity of the PEDOT:PSS films was significantly increased from 0.33 to 3748 S cm^?1 after a series of sequential treatments with trifluoroacetic acid (TFA) while the Seebeck coefficient and thermal conductivity were slightly reduced from 17.5 ± 1.2 to 16.0 ± 1.1 μV K^?1 and 0.537 to 0.415 W m^–1 K^?1 for the pristine film and treated film, respectively, leading to a significant improvement in power factor up to 97.1 ± 5.4 μW m^–1 K^?2. More importantly, around 80% of the electrical conductivity and Seebeck coefficient was retained after 20 days for these TFA‐treated PEDOT:PSS films, revealing the potential for real thermoelectric applications. © 2019 Society of Chemical Industry