颗粒种类及制备工艺对铜基材料性能影响

以纯铜为基体,以WC、AlN、TiN、MgB2等具有不同导电性能与密度的陶瓷颗粒为增强相,采用粉末冶金工艺制备了WCp/Cu、AlNp/Cu、TiNp/Cu和MgB2p/Cu系列复合材料.研究了不同增强颗粒、制备工艺的不同环节对铜基复合材料导电性能的影响.结果表明:相同制备工艺及体积分数条件下,以具有不同导电性能与密度的陶瓷颗粒作为增强相的铜基复合材料的导电性能相近,混粉、压制、烧结、复压及复烧等工艺环节对铜基复合材料导电性能有不同程度的影响,提高铜基复合材料的致密度为提高其导电性能的关键.     

不同陶瓷颗粒增强Cu基复合材料的制备及导电性能

以纯铜为基体,以WC、AlN、TiN、MgB2等具有不同导电性能与密度的陶瓷颗粒为增强相,采用球磨-冷压-烧结工艺制备了WCp/Cu、AlNp/Cu、TiNp/Cu和MgB2p/Cu系列复合材料.研究了制备工艺的不同环节对铜基复合材料导电性能的影响,讨论了不同陶瓷颗粒增强铜基复合材料的导电性能.结果表明相同制备工艺及体积分数条件下,以具有不同导电性能与密度的陶瓷颗粒作为增强相的铜基复合材料的导电性能相近,球磨、冷压、烧结、复压及复烧等工艺环节对铜基复合材料导电性能有不同程度的影响,提高铜基复合材料的致密度为提高其导电性能的关键.     

颗粒增强铜基热沉复合材料的研制

本文研究了用常规粉末冶金工艺制备颗粒增强铜基热沉复合材料的机械物理性能。研究结果表明 :采用W和Al2 O3颗粒增强铜基热沉复合材料 ,可以有效地改善烧结铜材料的硬度和抗拉强度 ,提高抗高温回复性能 ;W颗粒增强铜基热沉复合材料比Al2 O3颗粒增强铜基热沉复合材料的热导率要高     

颗粒增强铜基热沉复合材料的研制

本文研究了用常规粉末冶金工艺制备颗粒增强铜基热沉复合材料的机械物理性能，研究结果表明，采用W和Al2O3颗粒增强铜基热沉复合材料，可以有效地改善烧结铜材料的硬度和抗拉强度，提高抗高温回复性能；W颗粒增强铜基热沉复合材料比Al2O3颗粒增强铜基热沉复合材料的热导率要高。     

叠层压铸法制备纳米碳纤维/铜基复合材料

在比较目前C/Cu复合材料主要制备工艺特点的基础上,采用叠层压铸法制备纳米碳纤维/铜基复合材料,初步探讨了温度、压力对材料相容性、显微组织和性能的影响.研究表明:在略高于铜熔点的温度及适当的压力下,可获得成型较好的纳米碳纤维/铜基复合材料,与不含纳米碳纤维的试样相比硬度值(Hv)提高约30%.实验中还观察到微量杂质硫以化合物Cu2S的形式在C/Cu复合体中聚集形成规则的富硫球状颗粒的现象.     

颗粒增强铜基复合材料的研究进展

为了研究颗粒增强相对铜基复合材料的性能的影响,对不同类型铜基复合材料的特点及其制备方法进行对比分析,探讨了颗粒相的生成机制,重点论述了颗粒增强相的类型及铜基复合材料的制备工艺.结果表明在铜基体中引入纳米分散相进行复合,可以使铜合金的力学性能得到极大改善,其中机械合金化和原位复合化学反应获得的纳米陶瓷颗粒在铜基复合材料中效果最佳;反应喷射沉积成型法、液相反应原位生成法和机械合金化法在制备纳米粒子增强铜基复合材料方面有着良好的应用前景.     

纳米Fe-Cu粉末的制备及其对铁基压坯烧结行为的影响

以化学共沉淀法制备出纳米Fe-Cu复合粉末并对其性能进行了表征,分别以此纳米Fe-Cu粉末和电解Cu粉与铁粉进行混合获得铁基粉末混合料,成形压坯在H2气氛中不同温度下进行烧结,测定基加入不同形态Cu(合金）粉末铁基烧结坯的烧结性能,结果表明,在相同的Cu添加量及烧结条件下,添加纳米Fe-Cu粉末较加入电解Cu粉于铁基压坯中可以明显地提高压坯烧结后的密度,硬度及强度等性能,而添加纳米Fe-Cu粉末压坯在较低温度下烧结可达到添加电解Cu粉压坯在较高温度下烧结后的性能水平,说明采用纳米Fe-Cu粉末形式向铁基压坯中引入Cu有利于制备高密度,高性能的铁基烧结材料。     

高能球磨工艺对CNTs／Cu复合粉末与材料性能影响

采用卧式高能球磨和机械合金化工艺制备了纳米碳管增强铜基（CNTs／Cu）复合粉体,并采用真空冷压烧结制备出CNTs／Cu复合材料,研究了高能球磨工艺参数对复合粉体与材料性能的影响规律,包括球磨时间和搅拌轴转速对复合粉体粒度、松装密度以及力学性能的影响,结果表明,高能球磨技术有利于CNTs与铜的界面结合和机械合金化。高能球磨的最佳工艺条件：搅拌轴线速度4．2／5．4m／s,球磨时间2～4h,得到的CNTs／Cu复合粉体的中位径为11．76μm,松装密度为1．356g／cm3。CNTs／Cu复合材料的致密度到达94％,硬度到达92HB,抗拉强度到达138Mpa。     

电铸nano-Al2O3 / Cu 复合材料的组织与性能

采用复合电铸工艺, 在硫酸铜镀液中加入纳米氧化铝颗粒制备了纳米颗粒弥散增强铜基复合材料, 利用扫描电镜、电子透镜对复合材料的表面、拉伸断面和摩擦磨损表面的形貌以及微观组织进行了观察, 并对显微硬度、拉伸性能、磨损性能及电阻率进行了研究。结果显示, 氧化铝颗粒及其团聚体以纳米级尺寸弥散分布在铜基体中, 且与铜基体结合良好。复合材料的硬度最大增幅达42 %。氧化铝颗粒含量在1. 26 %时, 复合材料的拉伸强度和延伸率分别高达385 MPa 、26 %。相对电铸纯铜, 复合材料的耐磨性能明显提高, 而复合材料的电阻率最大增幅小于6 %。      

掺杂纳米SnO_2-Al_2O_3/Cu新型电触头复合材料的制备及耐磨性能

为满足低压电器对于高品质电触头材料的迫切需求,同时保护稀缺资源、降低电触头成本,采用粉末冶金工艺制备了掺杂纳米SnO_2-Al_2O_3/Cu新型电触头复合材料,并对其电导率、硬度及耐磨性能进行了研究。结果表明:复烧与冷变形工艺均可显著提高复合材料的烧结质量、密度、电导率与硬度。随着纳米Al_2O_3及掺杂纳米SnO_2颗粒的总含量增加,掺杂纳米SnO_2-Al_2O_3/Cu电触头复合材料的硬度与耐磨性能表现出了相同的变化规律,即先升高后降低。当纳米Al_2O_3及掺杂纳米SnO_2颗粒的总含量为0.80wt%时,复合材料的硬度与耐磨性能均达到最优;而当纳米Al_2O_3及掺杂纳米SnO_2颗粒的总含量保持0.80wt%不变时,随纳米Al_2O_3颗粒的含量增加,掺杂纳米SnO_2-Al_2O_3/Cu电触头复合材料的硬度与耐磨性能改善;当掺杂纳米SnO_2颗粒的含量为0时,复合材料的耐磨性能达到了最优。因此较之掺杂纳米SnO_2颗粒,纳米Al_2O_3颗粒对掺杂纳米SnO_2-Al_2O_3/Cu电触头复合材料的耐磨性能有更显著的提高作用。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

From Industry 4.0 to Research 4.0. Development of High Performance Fibers in the Light of Digitization

We associate a variety of innovations with the term ＂Industry 4.0＂. The pioneer of many 4.0 modifications forms the basisfor the trend towards the integrated di...     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Roman iron and steel: A review

ABSTRACT

The production of ferrous metal increased during the Roman Late Republican period, Principate and Empire. The direct bloomery process was used to extract the metal from its ores using slag-tapping and slag-pit furnaces. The fuel was charcoal and an air blast was introduced by bellows-operated tuyères. Iron formed as a bloom, often as a spongy mass of metal, which contained impurities from the smelting process, including unreacted ore, fuel, slag and fragments from the furnace walls, while the metal was often inhomogeneous with varied carbon contents. Blooms were either smithed directly into bars or ingots or they were broken up, which also allowed the removal of gross impurities and a selection of pieces with similar properties to be made. These could then be forge-welded together and formed into characteristically shaped ingots. Making steel in the furnace seems to have been achieved: it depended on the ore and the furnace and conditions within it. Surface carburization was also carried out. Iron and steel were used extensively in construction and for tools and weapons. Fire welding was often used to add pieces of steel to make the edges of tools and weapons, which could be heat-treated by quenching to harden them.     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...