The thermal stability of ohmic contact to n-type InGaAs layer

The thermal stability of ohmic contact to n-type InGaAs layer is investigated. When Ni/Ge/Au is used as the contact metal, the characteristics of the ohmic contact are degraded after thermal treatment. The specific contact resistance of (Ni/Ge/Au)-InGaAs ohmic contact after annealing at 450°C is about 15 times larger than that of as-deposited sample. This is due to the decomposition of InGaAs and the interdiffusion of Ga and Au. A new phase of Au₄ln appears after annealing at 300°C. While in the case of Ti/Pt/Au, Au does not penetrate into the InGaAs layer as revealed by secondary ion mass spectroscopy. The specific contact resistance of (Ti/Pt/Au)-InGaAs ohmic contact after annealing at 450°C is eight times larger than that of as-deposited sample. Therefore, the thermal stability of (Ti/Pt/Au)-InGaAs ohmic contact is better than that of (Ni/Ge/Au)InGaAs ohmic contact.     

Thermally stable Ge/Ag/Ni Ohmic contact for InAlAs/InGaAs/InP HEMTs

Excellent annealed ohmic contacts based on Ge/Ag/Ni metallization have been realized in a temperature range between 385 and 500/spl deg/C, with a minimum contact resistance of 0.06 /spl Omega//spl middot/mm and a specific contact resistivity of 2.62 /spl times/10/sup -7/ /spl Omega//spl middot/cm/sup 2/ obtained at an annealing temperature of 425/spl deg/C for 60 s in a rapid thermal annealing (RTA) system. Thermal storage tests at temperatures of 215 and 250/spl deg/C in a nitrogen ambient showed that the Ge/Ag/Ni based ohmic contacts with an overlay of Ti/Pt/Au had far superior thermal stabilities than the conventional annealed AuGe/Ni ohmic contacts for InAlAs/InGaAs high electron mobility transistors (HEMTs). During the storage test at 215/spl deg/C, the ohmic contacts showed no degradation after 200 h. At 250/spl deg/C, the contact resistance value of the Ge/Ag/Ni ohmic contact increased only to a value of 0.1 /spl Omega//spl middot/mm over a 250-h period. Depletion-mode HEMTs (D-HEMTs) with a gate length of 0.2 /spl mu/m fabricated using Ge/Ag/Ni ohmic contacts with an overlay of Ti/Pt/Au demonstrated excellent dc and RF characteristics.     

Electrical properties at p-ZnSe/metal interfaces

In order to prepare low resistance ohmic contacts to p-ZnSn by the “deposition and annealing (DA)” technique which has been extensively used for GaAs and Si-based devices, formation of a heavily doped layer by the p-ZnSe/metal reaction is required. For p-ZnSe/Ni contacts, Ni and Se reacted preferentially at the ZnSe/Ni interface upon annealing at temperatures higher than 250°C. However, capacitance-voltage measurements showed that the net acceptor concentration (N_A-N_D) close to the p-ZnSe/Ni interface was reduced upon the Ni/ZnSe reaction, resulting in high contact resistance. For p-ZnSe/Au contacts, neither Au/ZnSe reaction nor reduction of the acceptor concentration were observed after annealing at temperatures lower than 300°C. This indicates that although the metal/p-ZnSe reaction is mandatory to prepare a heavily doped layer, the reaction induced an increase in the compensation donors in the p-ZnSe substrate. In order to increase the acceptor concentration in the vicinity of the p-ZnSe/metal interface through diffusion from the contact materials, Li or O which was reported to play the role of an acceptor in ZnSe was deposited with a contact metal and annealed at elevated temperatures. Ni or Ag was selected as the contact metal, because these metals were expected to enhance Li or O doping by reacting with ZnSe. However, the current density-voltage characteristics of the Li(N)/Ni and Ag(O) contacts exhibited rectifying behavior, and the contact resistances increased with increasing annealing temperature. The present results indicated that, even though the acceptor concentration in the p-ZnSe substrate increased by diffusion of the dopants from the contact elements, an increment of the compensation donors was larger than that of the acceptors. The present experiments indicated that preparation of low resistance ohmic contacts by forming a heavily doped intermediate layer between p-ZnSe and metal is extremely difficult by the DA technique.     

Alloyed Si/Al-based ohmic contacts to AlGaN/GaN nitride heterostructures

For the first time in Russia, the Si/Al/Ti/Au alloyed contact composition is investigated for the formation of ohmic contacts to AlGaN/GaN heterostructures using thermal annealing. The obtained results are compared with those for conventional Ti/Al/Ni/Au ohmic contacts. Use of the composition under investigation makes it possible to decrease the annealing temperature to 675–700°C, which results in improvement in the morphology of alloyed ohmic contacts in comparison with conventional contacts. The value of the contact resistance using the Si/Al-based composition to the AlGaN/GaN heterostructure is obtained in relation to the temperature and annealing duration. It is shown that no qualitative change in the resistance occurs at an annealing duration of several minutes in the temperature range of 700–750°C. In the temperature range of 675–700°C, there is an asymptotic decrease in the contact resistance with increasing annealing duration. The smallest value of the contact resistance amounts to 0.41 Ω mm.     

Formation of ohmic contacts to p-ZnTe

Formation and temperature stability of sputter deposited gold ohmic contacts to molecular beam epitaxially grown p-type ZnTe (doped with nitrogen to a free hole concentration of ≈3 × 1018 cm³) have been studied using current-voltage (I-V), Auger electron spectroscopy, secondary ion mass spectrometry, and optical and scanning electron microscopy. The I-V characteristics of ≈1500Å Au/p-ZnTe contacts were measured as-deposited and after heat treatments at 150, 200, 250, and 350°C for 15 min intervals up to 90 min. As deposited, the contacts were poor Schottky contacts, but became ohmic after 15 min at all temperatures. There was an increased resistance at t>15 min for T≤250°C, and a very large resistance increase upon heat treatment for all times at 350°C. The interface between the metallization and ZnTe was initially very planar, and remained planar upon formation of the ohmic contact. Upon heating at T>250°C, Au diffused into ZnTe. The ohmic behavior of the Au/p-ZnTe contacts is attributed to this diffusion which created a highly doped near-surface region in the ZnTe. Microscopy showed that Au also migrated across the ZnTe surface forming an extended reaction zone (≈100 μm) around the dot contact at T≥250°C.     

Thermally stable Nb and Nb/Au ohmic contacts to p-GaN

We have investigated Nb single and Nb/Au metallization schemes for the formation of thermally stable ohmic contacts to p-GaN. It is shown that the asdeposited Nb and Nb/Au contacts exhibit rectifying behavior. However, both the contacts produce ohmic characteristics when annealed at 850°C. Measurements show that the 850°C Nb/Au and Nb contacts yield a specific contact resistance of 1.9×10⁻⁸ and 2×10⁻² ωcm², respectively. Schottky barrier heights are found to decrease with increasing annealing temperature. A comparison of the XRD and electrical results shows that the formation of gallide phases such as Ga-Nb and Ga-Au compounds, play a role in forming ohmic contacts. Atomic force microscopy results show that the surface morphology of the Nb contacts is fairly stable up to 850°C, while the Nb/Au contacts are slightly degraded upon annealing at 850°C.     

Evolution of surface morphology of alloyed AuGe/Ni/Au ohmic contacts to GaAs microwave FETs

During post-deposition alloying of AuGe/Ni/Au ohmic contacts to microwave transistors, there is interdiffusion of alloy materials and GaAs into each other. Outdiffusion from substrate greatly influences the surface roughness of the contacts as a function of alloying temperature. During our experiments, we have observed that the RMS roughness of the contact surface followed the trend of contact resistance with alloying temperature. We seek to explain this evolution of surface morphology using a model involving the phenomena of coalescence and outdiffusion occurring simultaneously.     

Effect of annealing temperature on Ti/Al/Ni/Au ohmic contacts on undoped AlN films

The Ti/Al/Ni/Au metals were deposited on undoped AlN films by electron beam evaporation. The influence of annealing temperature on the properties of contacts was investigated. When the annealing temperatures were between 800 and 950℃, the AlN-Ti/Al/Ni/Au contacts became ohmic contacts and the resistance decreased with the increase of annealing temperature. A lowest specific contacts resistance of 0.379 Ω·cm² was obtained for the sample annealed at 950℃. In this work, we confirmed that the formation mechanism of ohmic contacts on AlN was due to the formation of Al-Au, Au-Ti and Al-Ni alloys, and reduction of the specific contacts resistance could originate from the formation of Au₂Ti and AlAu₂ alloys. This result provided a possibility for the preparation of AlN-based high-frequency, high-power devices and deep ultraviolet devices.     

Development of Al-free ohmic contact to n-GaN

We have investigated the electrical properties and interfacial reactions of the Si/Ti-based ohmic contacts to Si-doped n-GaN grown by metal organic chemical vapor deposition and the electrical properties were related to the material reactions. Si/Ti contact system was selected because Ti silicides have a low work function comparable to Al and also Si was used widely as an n-type dopant. As the annealing temperature increased, the specific contact resistance of Si/Ti-based ohmic contacts decreased and showed minimum contact decreased and showed minimum contact resistance as low as 3.86 10^?6 cm² after annealing at 900°C for 3 min under N₂ ambient. Our experimental results show that the ohmic behavior of Si/Ti-based contact, were attributed to the low barrier height of Ti-silicide/GaN interface, which was formed through the interfacial reaction between Si and Ti layers. In order to clarify the current conduction mechanism of Si/Ti-based contact, temperature dependent contact resistance measurement was carried out for Au(1000 Å)/Ti(400 Å)/Si(1500 Å)/Ti(150 Å) contact system after annealing at 700°C for 3 min. The contact resistance of Si/Ti-based ohmic contact decreased exponentially with the measuring temperature and so it can be concluded that current flows over the low barrier height by thermionic emission.     

Improved ohmic contact to n-type 4H and 6H-SiC using nichrome

Results are reported for ohmic contacts formed on n-type 4H and 6H-SiC using nichrome (80/20 weight percent Ni/Cr). The electrical characteristics of these NiCr contacts are similar to those of contacts formed on 6H-SiC using pure Ni (∼1×10⁻⁵Ω-cm² for moderately doped material), but the contacts exhibit significant improvement with regard to physical stability. Composite Au/NiCr contacts exhibit good stability during long-term anneals (∼2500 h) at 300°C without the requirement of a diffusion barrier layer between the NiCr ohmic contact layer and the Au cap layer. In addition, the use of NiCr results in success rates near 100% for direct wire bonding to the Au cap layers. Characterization of the contacts by Auger electron spectroscopy, Rutherford backscattering spectroscopy, and transmission electron microscopy provides an explanation for the observed behavior.     

The behavior of Ni/Au contacts under rapid thermal annealing in GaN device structures

The effect of rapid thermal annealing (RTA) on Ni/Au contacts on P-type GaN was investigated in terms of surface morphology and diffusion depth of metallic species. Ni/Au contacts were evaporated on the P-type 0.5 μm thick top layer of a GaN P/N homojunction. Optical micrographs revealed that the contact morphology degrades when annealed above 800°C for 1 min. At the same time, both Ni and Au atoms strongly diffuse in the P-type layer and even can reach the junction for a 1 min long annealing at 900°C, therefore making the junction structure unoperable. This behavior was evidenced using the Auger voltage contrast (AVC) technique.     

Vanadium-based ohmic contacts to n-type Al<Subscript>0.6</Subscript>Ga<Subscript>0.4</Subscript>N

Four vanadium-based contacts to n-type Al_0.6Ga_0.4N were compared in this work. Both V/Al/Pd/Au and V/Al/V/Au contacts with optimized layer thicknesses provided lower specific-contact resistances than did the previously reported V/Al/Pt/Au ohmic contact. Specific contact resistances of the V/Al/Pd/Au (15 nm/85 nm/20 nm/95 nm) and V/Al/V/Au (15 nm/85 nm/20 nm/95 nm) contacts were 3×10⁻⁶ Ω·cm² and 4×10⁻⁶ Ω·cm², respectively. On the other hand, an analogous V/Al/Mo/Au contact never became ohmic, even after it was annealed at 900°C for 30 sec. Compared to the V/Al/Pd/Au contact, the V/Al/V/Au contact required a less severe annealing condition (30 sec at 700°C instead of 850°C). The V/Al/V/Au contact also provided a smoother surface, with a root-mean-square (RMS) roughness of 39 nm.     

Study of contact resistivity, mechanical integrity, and thermal stability of Ti/Al and Ta/Al ohmic contacts to n-type GaN

The annealing conditions and contact resistivities of Ta/Al ohmic contacts to n-type GaN are reported for the first time. The high temperature stability and mechanical integrity of Ti/Al and Ta/Al contacts have been investigated. Ta/Al (35 nm/115 nm) contacts to n-type GaN became ohmic after annealing for 3 min at 500°C or for 15 s at 600°C. A minimum contact resistivity of 5×10⁻⁶Ω cm² was measured after contacts were repatterned with an Al layer to reduce the effect of a high metal sheet resistance. Ti/Al and Ta/Al contacts encapsulated under vacuum in quartz tubes showed a significant increase in contact resistivity after aging for five days at 600°C. Cross section transmission electron microscopy micrographs and electrical measurements of aged samples indicate that the increased contact resistivity is primarily the result of degradation of the metal layers. Minimal reactions at the metal/GaN interface of aged samples were observed.     

Reliability of AuGe/Pt and AuGe/Ni ohmic contacts on GaAs

The reliability of AuGe/Pt and AuGe/Ni ohmic contacts with and without overlay metal (Ti/Au, Ti/Pt/Au or TiW/Au) has been studied. AuGe/Ni contacts have proved superior and more reliable than AuGe/Pt contacts with or without overlay. AuGe/Pt contacts are stable without overlay but degrade rapidly with overlay. AuGe/Ni contacts exhibit thermal stability after 1000 hours' aging at 250°C.     

Use of Au/Te/Ni films for ohmic contact to GaAs

Ohmic contacts to n-type GaAs are usually fabricated by alloying AuGe/Ni films on GaAs. Ge acts as a donor to GaAs for fabrication of the ohmic contact. In an attempt to replace Ge, which is an amphoteric impurity, with a group VI element to improve on the ohmic contact resistivity, experiments were done with AuTe and AuTe/Ni contacts. A very low resistivity of ∼5 × 10^-7Ω.cm²was obtained by alloying 1700 Å of AuTe film with 300 Å of nickel on top at 510°C. This is the lowest contact resistivity obtained with any material other than AuGe/Ni on n-type GaAs.     

Pd/Zn/Pd/Au ohmic contacts to ρ-Type InP

Low resistance ohmic contacts (ρ_c = 7 x 10^-5 Ω-cm ² ) have been fabricated to Zn-doped p-type InP using an annealed Pd/Zn/Pd/Au metallization. Palladium reacts with InP at low temperatures to form a Pd₂InP ternary phase, which is initially amorphous but crystallizes and grows epitaxially on InP. Zinc reacts with some of the overlying Pd to form PdZn (≅250° C), which decomposes at 400-425° C to form PdP₂, freeing up Zn to diffuse into Au as well as InP. The contact resistance reaches a minimum as the decomposition reaction takes place. The resultant ohmic contact is laterally uniform and consists of epitaxial Pd₂InP adjacent to InP, followed by a thin layer of PdP₂ and then the outer Au layer. Further annealing leads to a breakdown of the contact structure,i.e. decomposition of Pd₂InP, and an increase in contact resistance.     

The ohmic contact formation mechanism of Au/Pt/Pd ohmic contact to p-ZnTe

The ohmic contact formation mechanism and the role of Pt layer of Au(500Å) Pt(500Å)/Pd(100Å) ohmic contact to p-ZnTe were investigated. The specific contact resistance of Au/Pt/Pd contact depended strongly on the annealing temperature. As the annealing temperature increased, the specific contact resistance decreased and reached a minimum value of 6×10^?6 Θcm² at 200°C. From the Hall measurement, the hole concentration increased with the annealing temperature and reached a maximum value of 2.3×10¹⁹ cm^?3 at 300°C. The Schottky barrier height decreased with the increase of annealing temperature and reached a minimum value of 0.34 eV at 200°C and it was due to the interfacial reaction of Pd and ZnTe. Therefore, the decrease of contact resistance was due to the increase of doping concentration as well as the decrease of Schottky barrier height by the interfacial reaction of Pd ZnTe. The specific contact resistances of Au Pd, Au/Pt/Pd and Au/Mo/Pd as a function of annealing time was investigated to clarify the role of Pt layer.     

Ohmic contact using the Si nano-interlayer for undoped-AlGaN/GaN heterostructures

Excellent ohmic characteristics for undoped-AlGaN/GaN heterostructures have been achieved by using a Si nano-interlayer: a 1-nm Si layer has been evaporated followed by Ti/Al/Mo/Au evaporation. A contact transfer resistance of 0.18 Ω-mm and a specific contact resistivity of 1 × 10⁻⁶ Ω-cm² have been achieved along with excellent surface morphology at an optimized annealing temperature (800°C). Both ohmic contact characteristics and surface morphology are significantly better than those obtained without the Si nano-interlayer. Auger depth profiles and temperature-dependent current-voltage characteristics were investigated to understand ohmic formation. It is suggested that titanium silicide formation at the interface during rapid thermal annealing lowers the barrier height and enhances thermionic emission current.     

Au/Ge/Ni ohmic contacts to n-Type InP

The relationship between the electrical properties and microstructure for annealed Au/Ge/Ni contacts to n-type InP, with an initial doping level of 10¹⁷ cm^-3, have been studied. Metal layers were deposited by electron beam evaporation in the following sequence: 25 nm Ni, 50 nm Ge, and 40 nm Au. Annealing was done in a nitrogen atmosphere at 250-400‡C. The onset of ohmic behavior at 325‡C corresponded to the decomposition of a ternary Ni-In-P phase at the InP surface and the subsequent formation of Ni₂P plus Au₁₀In₃, producing a lower barrier height at the InP interface. This reaction was driven by the inward diffusion of Au and outward diffusion of In. Further annealing, up to 400‡C, resulted in a decrease in contact resistance, which corresponded to the formation of NiP and Au₉ln₄ from Ni₂P and Au₁₀In₃,respectively, with some Ge doping of InP also likely. A minimum contact resistance of 10^-7 Ω-cm² was achieved with a 10 s anneal at 400‡C.