首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到19条相似文献,搜索用时 531 毫秒
1.
提出了一种具有高隔离度的紧凑型三陷波超宽带(ultra-wideband, UWB)多输入多输出(multiple-input multiple-output, MIMO)天线,整体尺寸为38 mm×26 mm×1.2 mm.通过对辐射贴片底部两侧进行多切角,实现了宽带化;通过在接地板上加载改进的波纹T型去耦结构,并刻蚀倒“π”型槽缝隙,实现了较高隔离度;通过在辐射贴片上刻蚀“U”型缝隙、在馈线上刻蚀类“H”型缝隙以及在右侧引入倒“C”型寄生枝节,实现了WiMAX(3.3~3.6 GHz)、WLAN(5.15~5.85 GHz)和X波段(7.25~7.75 GHz)3个频段的陷波.仿真与测试结果表明,该天线工作频段为2.9~11.3 GHz(相对带宽达到118.31%),隔离度小于-22.6 dB,包络相关系数小于0.01,辐射效率高,辐射特性良好,可以广泛应用于无线通信系统领域中.  相似文献   

2.
杨萍  王代强 《电子元件与材料》2023,(10):1256-1262+1267
针对超宽带(Ultra-Wideband, UWB)多输入多输出(Multiple-Input Multiple-Output, MIMO)天线存在陷波数量少和隔离度不高等问题,提出了一种四端口多陷波超宽带天线。将带有梯形缺口的椭圆形与圆形结合作为辐射贴片实现超宽带功能,利用上下层的十字结构提高隔离度。通过在辐射贴片上蚀刻一个C型开口环槽和一个类C型槽以及添加一对C型开口环,实现WIMAX(3.3~3.6 GHz)、国际移动通信系统(IMT-2020(5G))通信波段(4.84~4.98 GHz)、X下行波段(7.25~7.75 GHz)、国际电信联盟ITU(8.025~8.4 GHz)四个陷波频段。仿真与实测结果表明,该UWB-MIMO天线的工作带宽为3.0~14.0 GHz,仿真结果与实测结果基本吻合。天线隔离度小于-25 dB,包络相关系数(ECC)整体小于0.007,分集增益(DG)值大于9.999,性能指标良好,可以满足UWB-MIMO天线的要求。  相似文献   

3.
该文设计了一款具有单陷波特性的高隔离超宽带(UWB)四单元多输入多输出(MIMO)天线。天线的尺寸为65 mm×65 mm×0.8 mm。4个槽天线单元水平正交放置,采用易加工集成的共面波导(CPW)馈电,引入缺陷地及十字隔离枝节去耦。通过在天线辐射贴片上刻蚀一个U 形槽,在4.35~6.08 GHz处产生陷波,能阻止WLAN(5.15~5.825 GHz)的通信干扰。经实测,该天线的工作频段为2.46~10.6 GHz,隔离度<-20 dB,在4.35~6.08 GHz产生覆盖WLAN 的阻带,包络相关系数<0.02,分集增益>9.998,实测性能良好。该天线能够广泛应用于UWB-MIMO 通信系统。  相似文献   

4.
为有效抑制部分毫米波通信信号干扰,实现无线通信设备小型化,设计了一款具有双陷波特性的毫米波宽带MIMO天线。天线基本单元由辐射单元、微带馈线、Rogers RO4350B基板以及接地板构成。通过在天线辐射贴片刻蚀U型槽,以及接地板添加倒U型枝节,可在工作频段内产生双陷波特性;进一步在接地板引入圆形开槽使MIMO天线获得良好的隔离度。该天线结构紧凑,尺寸仅为26.7 mm×16.67 mm×1.524 mm,工作于21~40 GHz频段,其中陷波频段为22.04~24.72 GHz和25.96~31.2 GHz。结果表明:该天线在工作频段内隔离度大于20 dB,最大增益可达8.49 dBi,包络相关系数(ECC)均小于0.002,具有良好的辐射和增益性能,在毫米波超宽带通信中具有应用潜力。  相似文献   

5.
提出了一种紧凑型的二端口双陷波超宽带MIMO 天线。该天线由两个圆形单极子和一个缺陷地结构组成,在两个单极子辐射片上刻蚀开口圆环槽,并在两个50Ω馈电微带线旁分别增加终端短路的低-高-低阶跃阻抗谐振器,实现了双陷波的功能,分别抑制了无线局域网WLAN(5.15~5.85 GHz)和802.16无线城域网WiMAX(3.4~3.8GHz)信号对该天线系统的干扰;并在介质板地层和顶层增加隔离枝节,提高了隔离度。实验结果表明:该天线在-10dB 的工作带宽为3.0~13.8 GHz,第一个陷波带宽为3.37~3.85GHz,第二个陷波带宽为5. 02~6.14 GHz,有效抑制了WiMAX 和WLAN信号干扰;工作频带内,最小隔离度为13.5 dB,最大增益为4.94 dB,最大辐射效率为96.6%,包络相关系数小于0.07。测试表明该天线适用于多输入-多输出超宽带(MIMO-UWB)系统,且该天线结构紧凑,尺寸仅为47.5 mm×47.5 mm×0.8 mm,易用于便携式设备。  相似文献   

6.
为了适应UWB系统对天线小型化的需求,设计了一款紧凑型UWB-MIMO天线,天线尺寸仅为23 mm×31 mm×1.6 mm。通过引入阶梯状结构,极大改善了天线带宽。测试结果显示所设计的UWB-MIMO天线的阻抗带宽为2.9~28 GHz,带宽比为9.6∶1。整个频段内互耦程度小于-15 d B,中高频段小于-20 d B,很好地满足了UWB系统对MIMO天线带宽和互耦程度的要求。在此基础上,对地板进行改造,实现了天线的双陷波特性。  相似文献   

7.
提出了一款紧凑型陷波超宽带多输入多输出(ultra wideband multiple-input multiple-output,UWB-MIMO)天线,天线印制在FR4基板上,由两个相同的天线单元正交放置组成,尺寸是46 mm×46 mm×0.8 mm.天线单元由阶梯矩形组成,采用微带线馈电,在天线单元上蚀刻矩形开口谐振环,实现了陷波的功能,解决了无线局域网WLAN(5.15~5.85 GHz)的电磁干扰问题.通过在介质基板接地层的对称轴增加隔离枝节,使端口隔离度由-12 dB提高至-16 dB.实测结果表明:该天线的工作带宽为2.95~11.2 GHz,峰值增益是6.43 dBi,最大辐射效率可以达到97.96%,包络相关系数(envelope correlation coefficient,ECC)低于0.02.结果表明所提出的带有滤波功能的天线是一种有实际应用价值的紧凑型陷波UWB-MIMO天线.  相似文献   

8.
提出了一种紧凑、高性能、形状新颖的具有高隔离度的超宽带多输入多输出(ultra-wideband multiple-input multiple-output, UWB-MIMO)天线.天线由两个圆形辐射元件组成,享有共同的类F形接地平面,尺寸为30 mm×18 mm.在天线的接地平面中引入类F形短截线,在MIMO天线元件之间产生高度隔离.所设计的UWB-MIMO天线具有极低耦合(S21<-22 dB)、低包络相关系数(ECC<0.003)、高分集增益(DG>9.98 dB),适用于便携式通信设备.  相似文献   

9.
一种小型化超宽带MIMO天线设计   总被引:1,自引:0,他引:1       下载免费PDF全文
提出了一种基于槽天线的小型化、高隔离度的超宽带(Ultra Wideband, UWB)多入多出(Multiple-Input Multiple-Output, MIMO)天线.该MIMO天线由两个槽天线单元构成, 为了增加天线阻抗带宽, 每个槽天线单元由末端带有圆形贴片的微带线和末端为圆形的槽线两部分耦合馈电.采用在地板上开槽和方向图分集方法, 减少地板表面波和空中电磁波影响, 达到提高天线隔离度的目的.数值仿真和实验结果表明:该天线在3.1~11 GHz频段内满足端口反射系数|S11| < -10 dB, 隔离度|S12|在7~11 GHz频段内小于-25 dB, 在3.1~7 GHz频段内小于-16 dB, 并根据仿真和测试S参数计算了包络相关系数.  相似文献   

10.
为了滤除WIMAX(3.3~3.8 GHz)和WLAN(5.125~5.825 GHz)窄带信号对超宽带系统的干扰,该文提出一款共面波导馈电的小型化双陷波渐变槽天线。共面波导结构可以有效地扩展天线的带宽,实现对整个UWB(3.1~10.6 GHz)频段的全覆盖。通过在天线的馈线上开L型缝隙和在辐射贴片上开一对E字型缝隙的方法,有效实现了在3.15~3.97 GHz和4.94~6.05 GHz频段的双陷波特性,能够抑制WIMAX和WLAN对超宽带系统的干扰。该天线结构简单紧凑,尺寸非常小,仅为40 mm×18 mm×0.813 mm。仿真和实测结果表明该天线在超宽带波段内具有良好的陷波特性、增益特性,可以应用于小型化超宽带系统中。文中方法对于陷波渐变槽天线的研究具有一定的借鉴意义。  相似文献   

11.
提出了一种小型化的双陷波可重构超宽带(ultra wide band,UWB)天线,通过在辐射贴片上刻蚀大、小两个C形槽,实现5G (3.3~4.4 GHz)/WiMAX (3.3~3.6 GHz)和WLAN (5.150~5.825 GHz)两个频段的陷波.采用两个PIN二极管跨接在C形槽上,通过控制PIN二极管的通...  相似文献   

12.
A compact ultrawideband multiple input multiple output antenna with dual band notch characteristics is proposed. The design utilizes the property of quasi-self-complementary monopoles to achieve a bandwidth that ranges from 2.2 GHz to 11 GHz. The design has a compact size of 30 mm × 41 mm × 1.59 mm. Two quasi-self complementary half circular monopoles are symmetrically arranged to obtain MIMO antenna. Bandnotch characteristics are obtained by adding parasitic strips of Levy's Fractal shape near the feed line. A Hilbert Fractal shaped slot is etched in the ground plane to enhance the isolation (|S21| < −20 dB) throughout the operational bandwidth. The measured and simulated radiation patterns are in good agreement and is found to be stable throughout the ultrawideband. Moreover, the measured peak gain is found to be 4 dBi.  相似文献   

13.
In this paper, a novel multiple slot loading technique is studied in detail for the isolation enhancement of the dual‐band MIMO antenna system. The proposed MIMO antenna design consists of the microstrip patch loaded with T‐shaped slots parallel to the non‐radiating edge of the patch. The frequency tuning could be achieved by varying the length of the T‐shape slot arm. The proposed MIMO antenna system is optimised for operation in WLAN and WiMAX applications. The isolation enhancement is achieved by providing simple multiple slots loaded in the ground plane between radiating elements. The length of the slots is λ/4 . The system is fabricated and tested using a vector network analyser and anechoic chamber. The reduction in mutual coupling up to ?29.16 dB and ?24.09 dB for the 2.4 GHz and 3.4 GHz, respectively, is achieved. The bandwidths are 62.3 MHz (3.33–3.39 GHz) and 55.5 MHz (2.37–2.42 GHz), respectively. The total gain obtained in this case is 1.8 dBi at 2.4 GHz and 1.2 dBi at 3.4 GHz, respectively. The dimensions of the proposed designed antenna are 70 mm × 60 mm × 1.6 mm. The results were also verified through mutual coupling parameters like envelope correlation coefficient (ECC) and channel capacity loss (CCL) at the desired frequencies.  相似文献   

14.
This article proposes a novel printed monopole antenna for ultra wideband applications with dual band-notch function. The antenna consists of a disc-shaped radiating patch with a pair of folded strips arms, and a ground plane with a two L-shaped conductor backed plane, which provides a wide usable fractional bandwidth of more than 140 % (2.6–14.43 GHz). In order to generate single band-notch characteristics, we use a modified disc-shaped radiating patch with a pair of folded strips arms also by using this modified radiating patch, additional resonance is excited and hence much wider impedance bandwidth can be produced, especially at the higher band. By adding two L-shaped conductor backed plane in the ground plane a dual band notch function is achieved. The measured results reveal that the presented dual band-notch monopole antenna offers a very wide bandwidth with two notched bands, covering all the 5.2/5.8 GHz WLAN, 3.5/5.5 GHz WiMAX and 4 GHz C bands. The designed antenna has a small size of $12\times 18\,\hbox {mm}^{2}$ .  相似文献   

15.

In this paper, a novel compact semi-circular slot (SCS) 2 × 2 MIMO antenna is presented for 5G NR sub-6 GHz applications with high isolation. The proposed antenna consists of a semi-circular slot in ground plane, U-shaped stub, and 50-ohm microstrip feed line. The novelty of this paper are the Semi-Circular Slot acts a radiator, the port isolation  is enhanced using a simple conductor strip as a neutralization line, very compact in size, low ECC, and good impedance matching. The overall size of the proposed SCS MIMO antenna is 16 mm x 21 mm, and FR4 substrate is used with thickness of 1.6 mm. The two SCS antenna elements are separated by edge-to-edge distance of 1mm (\(=0.019\lambda _{0}\)). The proposed compact MIMO antenna design is simulated using Ansys HFSS. To validate SCS MIMO antenna, a prototype was fabricated and tested. The measured results are attained at 5.5 GHz with isolation greater than 25dB, impedance bandwidth (S11\(<-10\) dB) covers from 5.10 GHz to 5.80 GHz with return loss of ? 39.5 dB. The MIMO antenna parameters, ECC, CCL, TARC, and MEG are studied, and the values are obtained within acceptable limits. The measured and simulated antenna results are almost similar. This compact MIMO antenna is suitable for 5G communications in sub-6 GHz wifi-5 band applications.

  相似文献   

16.
This article introduces a novel and groundbreaking approach combining multiple-input-multiple-output (MIMO) technology with radio frequency (RF) energy harvesting. The proposed antenna consists of two semi-circular monopole antenna components, optimized with dimensions of 89 × 51.02 × 1.6 mm3, that share a common ground plane to achieve MIMO characteristics. A series of split-ring resonators on the ground plane significantly enhances the isolation between the two radiating components. Band-notched features are performed in the 3.5 GHz WiMAX and 5.5 GHz WLAN bands through modified C-shaped slots in the radiating patch and two rectangular split-ring resonators serving as parasitic devices near the feed line. The reconfiguration of band-notching is made possible by controlling the modes of the embedded PIN diodes. The two antenna elements maintain mutual coupling below −18 dB from 1.5–13 GHz, achieving an impressive 158.62% impedance bandwidth. The antenna's efficiency and gain experience significant drop, indicating effective interference suppression at the center frequencies of the notch bands, and its performance in MIMO systems is assessed through parameters including envelope correlation coefficient, port isolation, radiation patterns, efficiency, gain, and diversity gain. The simulated properties of the designed antenna closely align with the measured outcomes, demonstrating its reliability and consistency. Moreover, the article evaluates the antenna's potential for RF energy harvesting, achieving a maximum harvested energy of 4.88 V. This proposed antenna can be used in multiple applications, like wideband, band-notching MIMO, and RF energy harvesting. This proposed antenna is an efficient, reconfigurable wideband MIMO antenna with novel RF energy harvesting capability.  相似文献   

17.

A wideband, multi-standard MIMO antenna with hexagonal geometry and slot is proposed for DCS/PCS/LTE/UMTS applications while keeping the real time application at prime to provide high data rate, low latency, high capacity, non-line-of communication, and reliability with continuity. The designed prototype covers 1.64–2.50 GHz frequency band with percentage bandwidth of 41.55% and resonates at 2.1 GHz. The isolation of more than 10 dB is achieved in the 2:1 VSWR frequency band. The total bandwidth of the MIMO antenna is 860 MHz. The designed MIMO has peak gain of 5.4 dBi, ECC?<?0.06, radiation efficiency?>?88%, and total efficiency?>?71%. The TARC active bandwidth is 600 MHz with best excitation angles of 45°, 45° at ports. The hexagonal slot is used for the control of induced current for better isolation. The proposed MIMO antenna evaluates the SAR performance at resonant frequency for listening, holding, and watching positions, and is found under the required safety norms.

  相似文献   

18.
ABSTRACT

A compact planar Ultrawideband (UWB) monopole antenna with quadruple band notch characteristics is proposed. The proposed antenna consists of a notched rectangular radiating patch with a 50 Ω microstrip feed line, and a defected ground plane. The quadruple band notched functions are achieved by utilising two inverted U-shaped slots, a symmetrical split ring resonator pair (SSRRP) and a via hole. The fabricated antenna has a compact size of 24 mm × 30 mm × 1.6 mm with an impedance bandwidth ranging from 2.86 to 12.2 GHz for magnitude of S11 < ?10 dB. The four band notched characteristics of proposed antenna are in the WiMAX (worldwide interoperability for microwave access) band (3.25–3.55 GHz), C band (3.7–4.2 GHz), WLAN (wireless local area network) band (5.2–5.9 GHz) and the downlink frequency band of X band (7–7.8 GHz) for satellite communication are obtained. The measured and simulation results of proposed antenna are in good agreement to achieve impedance matching, stable radiation patterns, constant gain and group delay over the operating bandwidth.  相似文献   

19.

This article presents a compact Co-Planar Waveguide (CPW) fed antenna for next-generation Vehicular Communications. The antenna is designed by employing two rectangular stacked patch structures and slots, making the antenna resonate at dual frequency bands. The analytical study of antenna design is carried out using the governing microstrip patch equations. On optimizing the patch's dimensions for CPW structures, the desired frequency range of operation is obtained for the single element antenna structure. The designed antenna resonates at 3.5 GHz (LTE-42 Band) and 5.9 GHz (DSRC Band), yielding this antenna to be a prime component for Vehicular to Everything (V2X) Communication. The optimized single-element antenna structure is 35 mm?×?20 mm designed on an FR-4 substrate of thickness 1.6 mm. The substrate has a dielectric constant of 4.4 and a loss tangent value of 0.001. Further, the antenna structure is developed as a 4-element MIMO configuration with the distance between adjacent antenna elements to be 10 mm. The adjacent antennas in the MIMO configuration are positioned orthogonal to each other, thereby exhibiting better isolation between the antenna elements. The antenna has a reflection coefficient value of?<??10 dB within the bandwidth of interest and VSWR less than 2. The Gain value of the designed antenna ranges between 2.8 and 2.9 dBi at 3.5 GHz and between 3.6 and 3.7 dBi at 5.89 GHz. The overall efficiency of the antenna element is between 60 and 80% at both frequency bands. MIMO parameters are analyzed by calculating the Channel Capacity Loss (CL), Diversity Gain (DG), Envelope Correlation Coefficient (ECC) and Total Active Reflection Co-Efficient (TARC). The designed antenna is fabricated and tested, which shows the measured results coincide with the simulated antenna results. The overall dimension of the MIMO configured antenna design is 60 mm × 60 mm × 1.6 mm, which is highly compact and is a suitable candidate for deployment of Vehicle to Vehicle (V2V), Vehicle to Infrastructure (V2I), and Vehicle to Network (V2N) scenarios.

  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号