Zinc removal in anaerobic sulphate-reducing liquid substrate process

Zinc and sulphate removal from synthetic wastewater was investigated by using four laboratory parallel upflow-mode reactors (referred as R1 to R4; R1 contained carriers to retain biomass, whereas R2–R4 were operated as suspended reactors). All reactors were inoculated with anaerobically digested cow manure. R1 and R2 were first fed with glucose- and sulphate-containing feed for 48 days after which all four reactors were fed with wastewater containing 50 mg l⁻¹ of zinc in R1–R3 and 200 mg l⁻¹ in R4 and operated for 96 days. In all reactors, hydraulic retention time, organic loading rate, and sulphate load were 5–6 d, 0.2–0.4 kg COD m⁻³ d⁻¹ and 3.3–3.8 g SO₄ l⁻¹ d⁻¹, respectively, whereas the zinc load in R1–R3 was 0.074–0.077 and in R4 0.282 g Zn l⁻¹ d⁻¹. During the runs, 30–40% of sulphate and over 98% of zinc was removed, and up to 150–200 mg H₂S was produced in all reactors. Effluent pH dropped in all reactors (feed pH 6.5) to 3–5 by the end of the experiment. No significant effects on zinc removal were observed, despite differences in operating conditions and feed. It was only in the latter part of the runs (i.e. between experiment days 120–142) that zinc removal began to fluctuate, showing a negligible decrease in R3 and R4, whereas in R1 and R2 zinc was removed below the limit of detection (<0.01 mg Zn l⁻¹). Qualitative X-ray diffraction analysis of the reactor sludge at the end of the runs indicated that the compounds precipitated were most probably ZnS (Code 05-0566 Sphalerite), suggesting metal removal through sulphide precipitation; this was supported by the fact that sulphate was reduced and zinc removed simultaneously.     

Simultaneous determination of iron and copper in pregnant liquid solutions

A new method for the determination of Fe_Total and Cu is proposed. The method is based on the formation of the iron and copper complexes with 5-sulfosalicylic acid (SSA), the optimal conditions were found, using SSA 5.1 g L⁻¹ in the presence of ammonia 7.5 g L⁻¹ (pH = 10). Under these conditions the selected analytical wavelengths were 488.5 and 423.5 nm for the determination of iron and copper, respectively, by using the zero crossing approach. The detection and quantification limits were 0.02 mg L⁻¹ and 0.07 mg L⁻¹ for iron and 1.14 mg L⁻¹ and 3.80 mg L⁻¹ for copper. The proposed method was applied to the determination of both analytes in pregnant liquid solutions and the recovery was between 98% and 100% and in all cases the relative standard deviation was minor to 2%.     

Selective flotation of cassiterite with benzohydroxamic acid

The flotation of cassiterite mineral from gangue with a collector benzohydroxamic acid (BHA), and the interactions between the BHA and cassiterite have been investigated. It is shown through microflotation that the BHA is able to flot cassiterite very well, calcite quite limitedly, and quartz not at all, so the selective separation of cassiterite–quartz mixture was readily achieved; while for the efficient separation of cassiterite–calcite mixture containing 48.94% SnO₂, sodium hexametaphosphate (SHMP) was needed as a depressant for the gangue, and under the condition of the BHA 100 mg L⁻¹, SHMP 3.5 mg L⁻¹, a cassiterite concentrate with the grade of 85.50% SnO₂ was obtained with the recovery of SnO₂ 95.5%. Batch flotation further demonstrated that for an industrial tin slime, which contained 0.42% Sn, 13.65% SiO₂, 24.14% CaO, 16.60% MgO, 4.50% Al₂O₃ and 6.58% Fe, the tin recovery of 84.5% after one separation was reached with the concentrate grade of 1.84% Sn under the condition of the BHA 178 mg L⁻¹, SHMP 27 mg L⁻¹. In terms of zeta potential and infrared spectra studies the main interactions between the collector BHA and the mineral cassiterite in a flotation system are chemisorption with the formation of Sn–BHA compounds rather than electrostatic attractions between them.     

The removal of zinc from liquid streams by electroflotation

The removal of heavy metals from dilute aqueous solutions (in the range of 10⁻⁷–10⁻⁴ mol dm⁻³) is often not acceptable using classical methods, which do not achieve levels in accordance with environmental quality standards. Electroflotation has certain desirable characteristics, compared to dissolved and dispersed air flotation, particularly in regard to the small bubble size distribution of the process. The aim of this work was to develop an electroflotation (EF)/electrocoagulation (EC) cell to study this combined process and the influence of some relevant parameters/variables, such as collector concentration, tension and current density variation, on the removal of zinc from synthetic solutions containing 20 mg l⁻¹ of the metal. A platinum gore (5 mm) anode and stainless steel mesh cathode were used in the electroflotation cell. The work showed that it was possible to remove zinc by electroflotation, 96% removal being achieved using sodium dodecyl sulfate (SDS) as collector in the stoichiometric ratio 1:3, current density of around 8 mA/cm² and an inlet pH of about 7.0.     

Impact of organic carbon on the leachability of vanadium,manganese, iron and molybdenum from shale residues

From 1942 to the 1966, oil was produced by pyrolysis of shale, in Kvarntorp, Sweden. This generated some 40 million m³ of metal rich pyrolyzed shale and discarded fines that were piled on site with its original metal content almost intact. The present study focuses on the leaching of vanadium, manganese, iron and molybdenum from fines after addition of wood chips and steel slag, in outdoor 1 m³ reactor systems at low liquid to solid ratio, in order to evaluate the potential environmental impact and recovery of the elements from the leachates. Seasonal variations were observed, with increased leaching during peak summer. For vanadium and molybdenum, high addition of wood chips decreased the leaching, probably due to adsorption. Manganese showed the opposite behavior while leaching of iron was almost independent of the amount of wood chips. Depending on the systems, up to 2200 μg L⁻¹ vanadium, 90 μg L⁻¹ molybdenum, 25 mg L⁻¹ manganese and 500 mg L⁻¹ iron was found in the aqueous phase. Applied to the 40 million m³ pile, the annual leaching of those elements may reach 14 ton, 0.6 ton, 200 ton and 2400 ton, respectively.     

Sodium isopropyl xanthate degradation by advanced oxidation processes

This paper presents the results obtained by different oxidative processes when an aqueous solution containing sodium isopropyl xanthate is treated; this reagent is used in the flotation of copper minerals. The advanced oxidation processes used are UV photolysis, direct electrolysis and photoelectrooxidation. The solutions used containing sodium isopropyl xanthate were adjusted to the following concentrations: 6, 8, 10, 25 and 40 mg L⁻¹. The results show that the three oxidation processes proved to be suitable for the destruction of xanthate, with the following maximum destruction efficiencies: 76% for electrolysis, 95% for UV photolysis and 99% for photoelectrooxidation.     

Aqueous dispersions of nanobubbles: Generation,properties and features

Nanobubbles (NBs) have interesting and peculiar properties such as high stability, longevity and high surface area per volume, leading to important applications in mining-metallurgy and environmental areas. NBs are also of interest in interfacial phenomena studies involving long-range hydrophobic attraction, microfluidics, and adsorption at hydrophobic surfaces. However, little data are available on effective generation of concentrated NBs water dispersions and on their physicochemical and interfacial properties. In this work, air was dissolved into water at pH 7 and different pressures, and a flow was depressurized through a needle valve to generate 150–200 nm (mean diameter) NBs and MBs-microbubbles (about 70 μm). Microphotographs of the NBs were taken only in the presence of blue methylene dye as the contrast medium. Main results showed that a high concentration of NBs (number per volume) was obtained by decreasing the saturation pressure and surface tension. The number of NBs, at 2.5 bar, increased from 1.0 × 10⁸ NB mL⁻¹ at 72.5 mN m⁻¹ to 1.6 × 10⁹ NB mL⁻¹ at 49 mN m⁻¹ (100 mg L⁻¹ α-Terpineol). The NBs mean diameter and concentration only slightly varied within 14 days, which demonstrates the high stability of these highly concentrated NBs aqueous dispersions. Finally, after the NBs were attached to the surface of a grain of pyrite (fairly hydrophobic mineral), the NBs dramatically increased the population of MBs, which shows the enhancement of particle hydrophobicity due to NBs adhesion. The results were explained in terms of interfacial phenomena and it is believed that these tiny bubbles, dispersed in water at high concentrations, will lead to cleaner and more sustainable mineral flotation.     

Single and binary component sorption of the fission products Sr2+, Cs+ and Co2+ from aqueous solutions onto sulphate reducing bacteria

This study investigates the removal of the fission products Sr²⁺, Cs⁺ and Co²⁺ in single and binary metal solutions by a sulphate reducing bacteria (SRB) biomass. The effect of initial concentration and pH on the sorption kinetics of each metal was evaluated in single metal solutions. Binary component equilibrium sorption studies were performed to investigate the competitive binding behaviour of each metal in the presence of a secondary metal ion. Results obtained from single metal equilibrium sorption studies indicated that SRB have a higher binding capacity for Sr²⁺ (q_max = 416.7 mg g^?1), followed by Cs⁺ (q_max = 238.1 mg g^?1), and lastly Co²⁺ (q_max = 204.1 mg g^?1). Among the binary systems investigated, Co²⁺ uptake was the most sensitive, resulting in a 76% reduction of the sorption capacity (q_max) in the presence of Cs⁺. These findings are significant for future development of effective biological processes for radioactive waste management under realistic conditions.     

A novel low pH sulfidogenic bioreactor using activated sludge as carbon source to treat acid mine drainage (AMD) and recovery metal sulfides: Pilot scale study

In this work a pilot scale sulfidogenic bioreactor was used to treat acid mine drainage (AMD) from Zijinshang copper mine. In this process, S²⁻ produced in the Up-flow Anaerobic Sludge Bed (UASB) reactor were recycled in the two precipitation tanks for copper and iron precipitation, activated sludge from local waste water treatment plant was used as the carbon source. The reactor were steady operated in acid condition (with no pH control) for 4 month, AMD with a copper concentration of 100–120 mg/L, iron concentration of 170–200 mg/L, sulfate concentration of 2000–2500 mg/L and pH of 2.34–2.56, were feeding into the reactor under a feed rate of 1 m³/days and HRT of 3 days, copper and iron removal were 60.95%, 97.83% respectively. The precipitant in the precipitation tank containing 15.7% Cu and 22.66% Fe, thus indicating a recovery possibility of copper by pyrometallurgy process. From these results we can conclude that an SRB process would be a viable method of treating Zijinshan AMD.     

Preparation of immobilized sulfate reducing bacteria (SRB) granules for effective bioremediation of acid mine drainage and bacterial community analysis

Heavy metal-resistant immobilized sulfate-reducing bacteria (SRB) granules were prepared to treat acid mine drainage (AMD) containing high concentrations of multiple heavy metal ions using an up-flow anaerobic packed-bed bioreactor. The bioreactor demonstrated satisfactory performance at influent pH 2.8 and high concentrations of metals (Fe 463 mg/L, Mn 79 mg/L, Cu 76 mg/L, Cd 58 mg/L and Zn 118 mg/L). The effluent pH ranged from 7.8 to 8.3 and the removal efficiencies of Fe, Cu, Zn and Cd were over 99.9% except for Mn (42.1–99.3%). The bacterial community in the bioreactor was diverse and included fermentative bacteria and SRB (Desulfovibrio desulfiricans) involved in sulfate reduction. The co-existing anaerobic fermentative bacteria (Clostridia bacterium, etc.) with the ability to use lactate as electron donor could explain the differences between actual lactate consumption and what would be expected based solely on sulfate reduction.     

Biosorptive removal of Cd and Zn from liquid streams with a Rhodococcus opacus strain

The biosorption abilities of Rhodococcus opacus were studied for cadmium and zinc removal for liquid aqueous streams. The influence of pH, initial metal concentration and time removal were evaluated on the biosorption studies, in a batch scale basis. The Cd²⁺ and Zn²⁺ species uptake capacity by R. opacus has been also compared using Langmuir and Freundlich models. At pH 7.0 and 26 °C C, Cd²⁺ removal achieved a value around 60% from an initial concentration of 15 ppm. On the other hand, Zn removal achieved a value around 88% from an initial concentration of 5 ppm. Kinetics studies revealed that the biosorption process followed a pseudo-second order model for the two metal species (Cd²⁺ and Zn²⁺) and the kinetic constants were 3.90 and 3.37 g mg⁻¹ min⁻¹, for an initial concentration of 15 and 5 ppm for cadmium and zinc, respectively. The results showed that the R. opacus is a potential engineering biosorbent for environmental and extractive metallurgy sustainable applications.     

Simultaneous oxidation and immobilization of arsenite from refinery waste water by thermoacidophilic iron-oxidizing archaeon,Acidianus brierleyi

The use of a thermophilic acidophilic iron-oxidizing archaeon, Acidianus brierleyi, was investigated for oxidation and immobilization of As(III) from acidic refinery waste water. Some As(III) oxidation was measured in all Ac. brierleyi cultures independently of the presence or concentration of Fe(II) in bulk solution; the exception was at initial Fe(II) concentration ([Fe(II)]_ini) of 1000 mg l⁻¹ where As(III) oxidation became markedly facilitated and consequently approximately 70% of As was immobilized as amorphous ferric arsenate. Providing 1000 mg l⁻¹ Fe(III) instead of Fe(II) did not show the same effect, implying the importance of Fe(III) be microbially-produced and complexed in the archaeal EPS (extracellular polymeric substances) region for effective As(III) oxidation. The reaction towards secondary mineral formation shifted from ferric arsenate to jarosite at [Fe(II)]_ini of >1000 mg l⁻¹. Furthermore addition of jarosite seed crystals retarded the As(III) oxidation rate at [Fe(II)]_ini of 1000 mg l⁻¹. The observations indicate that by setting the appropriate bulk Fe(II)/As(III) ratio in Ac. brierleyi culture to achieve a certain concentration of Fe(III) within the EPS region, but at the same time to avoid jarosite formation, it is possible to maximize the As(III) oxidation rate and thus As immobilization efficiency. This study describes for the first time microbially-mediated simultaneous oxidation and immobilization of As(III) as ferric arsenate, using a thermoacidophilic iron-oxidizing archaeon, Ac. brierleyi.     

Multicolumn solid phase extraction with hybrid adsorbent and rapid determination of Au,Pd and Pt in geological samples by GF-AAS

A novel hybrid adsorbent (HA) composed of cellulose fiber, activated carbon, and anion exchange resin Dowex 1 × 8 was prepared for the preconcentration and separation of noble metals, namely, gold (Au), palladium (Pd) and platinum (Pt), in geological samples. The optimal experimental parameters, such as flow rate, sample volume and interfering ions, were investigated. The accuracy of the method was confirmed by added/found method for tap and sea water, and evaluated by analyzing certified reference materials with good agreement. Under the optimal experimental conditions, the detection limits (3σ criteria) of the developed technique were 0.008 ng mL⁻¹ (Au), 0.017 ng mL⁻¹ (Pd) and 0.014 ng mL⁻¹ (Pt) and the sample throughput reach to 30 samples every eight hours. Moreover, the adsorption capacity of HA for Au, Pd and Pt was determined to be 48.2, 35.9 and 29.8 mg g⁻¹, respectively.     

On the nanobubbles interfacial properties and future applications in flotation

Nanobubbles, generations forms, basic studies and applications constitute a growing research area, included their usage in advanced mineral flotation. Yet, there are investigation needs for sustainable generation procedures, stability and understanding the nanobubbles interfacial properties and structures. Results proved that a reduction in pressure makes the super-saturated liquid suffers cavitation and nanobubbles were generated. Medium pH and solutions tested were adjusted, in the air saturation vessel, before the nanobubbles were formed, and this allowed to control (in situ) the surface charge/zeta potential-size of the forming nanobubbles. Measurements obtained with a ZetaSizer Nano equipment showed zeta potential values, in the presence of 10⁻² mol L⁻¹ NaCl, displaying sigmoidal pH behaviour between pH 2 (+26 mV) and 8.5 (−28 mV); an isoelectric point was attained at pH 4.5 and were positively charged (up to 23 mV) in acidic medium, a phenomenon which has not been previously observed. In alkaline medium, bubbles were highly negative zeta potential (−59 mV) at pH 10. The double layers appear to play a role in the formation of stable nanobubbles providing a repulsive force, which prevents inter-bubble aggregation and coalescence. Accordingly, the sizes of the nanobubbles depended on their charge and increased with pH, reaching a maximum (720 nm) around the isoelectric point (±5 mV). Highly charged and small nanobubbles (approximately 150–180 nm) were obtained in the presence of surfactants (10⁻⁴ mol L⁻¹ of alkyl methyl ether monoamine or sodium dodecyl sulphate); the zeta potential values in these experiments followed a similar trend of other reported values, validating the technique used with the nanobubbles sizes varying with pH from 150 to 400 nm. Thus, charged and uncharged stable nanobubbles can be tailor-made with or without surfactants and it is expected that their use will broaden options in mineral flotation especially if collectors coated nanobubbles (“bubble-collectors”) were employed. A detailed and updated review on factors involving stability, longevity and coalescence of nanobubbles was made. It is believed that future trend will be on sustainable formation and application of nanobubbles at industrial scale contributing to widen applied research in mineral, materials processing and liquid effluent treatment by advanced flotation.     

Oxidation of cyanide in effluents by Caro’s Acid

Caro’s Acid (peroxymonosulphuric acid: H₂SO₅) is a powerful liquid oxidant made from hydrogen peroxide that has been adopted for the detoxification of effluents containing cyanides in gold extraction plants in recent years.The present work reports the findings of a study on the kinetics of aqueous cyanide oxidation with Caro’s Acid. Experiments were conducted in batch mode using synthetic solutions of free cyanide. The experimental methodology employed involved a sequence of two 2³ factorial designs using three factors: initial [CN⁻]: 100–400 mg/L; H₂SO₅:CN⁻ molar ratio: 1–1.5–3–4.5; pH: 9–11; each one conducted at one level of Caro’s Acid strength which is obtained with the H₂SO₄:H₂O₂ molar ratio used in Caro’s Acid preparation of 3:1 and 1:1. The objective was the evaluation of the effect of those factors on the reaction kinetics at room temperature. Statistical analysis showed that the three investigated variables were found to be significant, with the variables which affected the most being the initial [CN⁻] and the H₂SO₅:CN⁻ molar ratio. The highest reaction rates were obtained for the following conditions: H₂SO₅:CN⁻ molar ratio = 4.5:1; pH = 9; and Caro’s Acid strength produced from the mixture of 3 mol of H₂SO₄ with 1 mol of H₂O₂. These conditions led to a reduction of [CN⁻] from an initial value of 400 mg/L to [CN⁻] = 1.0 mg/L after 10 min of batch reaction time at room temperature. An empirical kinetic model incorporating the weight of the contributions and the interrelation of the relevant process variables has been derived as: −d[CN⁻]/dt = k [CN⁻]^1.8 [H₂SO₅]^1.1 [H⁺]^0.06, with k = 3.8 (±2.7) × 10⁻⁶ L/mg min, at 25 °C.     

Review of rate constants for thiosulphate leaching of gold from ores,concentrates and flat surfaces: Effect of host minerals and pH

A review of literature data for different types of sulphide concentrates and gold ores has been carried out to examine the impact of host minerals and pH upon gold leaching. Analysis of initial rate data over the first 30–60 min of gold leaching from sulphide concentrates or silicate ores over a range of ammonia, thiosulphate, and copper(II) concentrations, pH (9–10.5) and temperatures up to 70 °C shows the applicability of a shrinking sphere kinetic model with an apparent rate constant of the order k_ss = 10⁻⁶–10⁻³ s⁻¹. The dependence of apparent rate constant on pH and initial concentrations of copper(II) and thiosulphate is used to determine a rate constant k_Au(ρr)⁻¹ of the order 1.0 × 10⁻⁴–7.4 × 10⁻⁴ s⁻¹ for the leaching of gold over the temperature range 25–50 °C (ρ = molar density of gold, r = particle radius). These values are in reasonable agreement with rate constants based on electrochemical and chemical dissolution of flat gold surfaces: k_Au = 1.7 × 10⁻⁴–4.2 × 10⁻⁴ mol m⁻² s⁻¹ over the temperature range 25–30 °C. The discrepancies reflect differences in surface roughness, particle size and the effect of host minerals.     

Effect of thiocyanate on BIOX® organisms: Inhibition and adaptation

Stringent environmental legislation and the desire to become zero discharge have motivated mining operations to treat and recycle process water. Cyanidation tailings effluent contains elevated concentrations of cyanide and thiocyanate (SCN⁻), precluding recycling to the BIOX® process without prior treatment to reduce SCN⁻ to below 1 mg/l. The current study investigated the effect of SCN⁻ on individual microbial species. Iron oxidation by Leptospirillum ferriphilum was not affected by SCN⁻ concentrations below 0.5 mg/l, with concentration dependent inhibition observed between 0.75 and 1.25 mg/l and complete inhibition of iron oxidation above 1.25 mg/l. Sulphur oxidation by Acidithiobacillus caldus showed a similar trend, with limited inhibition below 1.25 mg/l and almost complete inhibition above 1.25 mg/l. Repeated sub-culturing at low concentrations induced adaptation, with adapted cultures currently growing at SCN⁻ concentrations of 7 mg/l. The phenomenon of inhibition at low concentration, with subsequent adaptation was repeated in stirred tank reactors, leaching a pyrite/arsenopyrite concentrate.     

Study on separation of heavy rare earth elements by solvent extraction with organophosphorus acids and amine reagents

The present work describes a study of the separation of rare earth elements (REE) from heavy REE concentrate through solvent extraction. Seven extractants were investigated: three organophosphorus acids (DEHPA, IONQUEST^®801 and CYANEX^®272), a mixture of DEHPA/TOPO (neutral ester) and three amines (ALAMINE^®336, ALIQUAT^®336 and PRIMENE^®JM-T). The organophosphorus extractants were investigated in hydrochloric and sulphuric media whereas the amines performance was assessed in a sulphuric medium. The variables investigated were: concentration of the extractant agent, aqueous phase acidity, aqueous/organic volumetric ratio, contact time, stripping agent concentration (hydrochloric acid solution) and the selective stripping step. In the extraction step, the best separation factors for the adjacent elements were obtained with DEHPA and IONQUEST 801. For 1.0 mol L⁻¹ DEHPA in an initial acidity of 0.3 mol L⁻¹ H⁺, the separation factor was 2.5 Tb/Dy, 2.1 Dy/Ho, 1.9 Ho/Er, 2.0 Ho/Y and 1.1 Y/Er; for 1 mol L⁻¹ IONQUEST 801 in 0.3 mol L⁻¹ of H⁺ it was 2.7 Tb/Dy, 2.4 Dy/Ho, 2.1 Ho/Er, 2.1 Ho/Y e 1.5 Y/Er. The study concluded that for the extractants investigated, IONQUEST 801 is the most indicated for the separation of heavy REE because it has lower affinity with the REE compared to the affinity of DEPHA/REE, which makes the strip of the REE from Ionquest 801 easier than from DEHPA. Moreover, the number of stages necessary for the stripping of the REE from IONQUEST 801 is much lower than that observed when DEPHA is employed.     

Process development for the recovery of europium and yttrium from computer monitor screens

This work describes the development of a process for the recovery of Eu and Y from cathode ray tubes (CRTs) of discarded computer monitors with the proposition of a flow sheet for the metals dissolution. Amongst other elements, europium and yttrium are presented in the CRTs in quantities – 0.73 w/w% of Eu and 13.4 w/w% of Y – that make their recovery worthwhile. The process developed is comprised of the sample acid digestion with concentrated sulphuric acid followed by water dynamic leaching at room temperature. In the CRTs, yttrium is present as oxysulphide (Y₂O₂S) and europium is an associated element – Y₂O₂S:Eu³⁺ (red phosphor compound). During the sulphuric acid digestion, oxysulphide is converted into a trivalent Eu and Y sulphate, in solid form, with the liberation of H₂S. In the second step, metals are leached from the solid produced in the acid digestion step by dynamic leaching with water. This study indicates that a proportion of 1250 g of acid per kg of the sample is enough to convert Eu and Y oxysulphide into sulphate. After 15 min of acid digestion and 1.0 h of water leaching, a pregnant sulphuric liquor containing 17 g L⁻¹ Y and 0.71 g L⁻¹ Eu was obtained indicating yield recovery of Eu and Y of 96% and 98%, respectively. Both steps (acid digestion and water leaching) may be performed at room temperature.     

Metal ions released from fluid inclusions of quartz associated with sulfides

The release of fluid inclusions has a strong potential for the unintentional activation of minerals during flotation. The present study aims to characterize fluid inclusions in natural quartz from a complex sulfide ore deposit. The results indicate that many fluid inclusions exist in the quartz. Under the experimental conditions of 2 g of quartz cleaned in 40 ml of pure deionized water under an inert atmosphere, the concentrations of Cu, Pb, Zn and Fe in aqueous solution reach concentrations of 1.92 × 10⁻⁷, 8.88 × 10⁻⁷, 8.31 × 10⁻⁷ and 90.33 × 10⁻⁷ mol/L, respectively. These values are significantly greater than those from the experimental non-oxidative dissolution of the quartz. In addition, the concentrations of metal ion released from fluid inclusions in the quartz sample at conditions approached “typical” industrial flotation environment are determined. The results indicate that the fluid inclusions of quartz represent the considerable sources of Cu, Pb, Zn and Fe in the aqueous solution. The present investigation provides a new understanding for the source of the unavoidable metal ions in the flotation pulp and may benefit understanding of the flotation theory.