Non-steady state simulation of BOM removal in drinking water biofilters: applications and full-scale validation

A biofilter model called "BIOFILT" was used to simulate the removal of biodegradable organic matter (BOM) in full-scale biofilters subjected to a wide range of operating conditions. Parameters that were varied included BOM composition, water temperature (3.0-22.5 degrees C), and biomass removal during backwashing (0-100%). Results from biofilter simulations suggest a strong dependence of BOM removal on BOM composition. BOM with a greater diffusivity or with faster degradation kinetics was removed to a greater extent and also contributed to shorter biofilter start-up times. In addition, in simulations involving mixtures of BOM (i.e. readily degradable and slowly degradable components), the presence of readily degradable substrate significantly enhanced the removal of slowly degradable material primarily due to the ability to maintain greater biomass levels in the biofilters. Declines in pseudo-steady state BOM removal were observed as temperature was decreased from 22.5 to 3 degrees C and the magnitude of the change was significantly affected by BOM composition. However, significant removals of BOM are possible at low temperatures (3-6 degrees C). Concerning the impact of backwashing on biofilter performance, BOM removal was not affected by backwash resulting in biomass removals of 60% or less. This suggests that periodic backwashing should not significantly impact biofilter performance as observed biomass removals from full-scale biofilters were negligible. In general, the simulation results were in good qualitative and quantitative agreement with experimental results obtained from full-scale biofilters.     

Treatment of a colored groundwater by ozone-biofiltration: pilot studies and modeling interpretation

Pilot studies investigated the fates of color, dissolved organic carbon (DOC), and biodegradable organic matter (BOM) by the tandem of ozone plus biofiltration for treating a source water having significant color (50 cu) and DOC (3.2 mg/l). Transferred ozone doses were from 1.0 to 1.8 g O3/g C. Rapid biofilters used sand, anthracite, or granular activated carbon as media with empty-bed contact time (EBCT) up to 9 min. The pilot studies demonstrated that ozonation plus biofiltration removed most color and substantial DOC, and increasing the transferred ozone dose enhanced the removals. For the highest ozone dose, removals were as high as 90% for color and 38% for DOC. While most of the color removal took place during ozonation, most DOC removal occurred in the biofilters, particularly when the ozone dose was high. Compared to sand and anthracite biofilters, the GAC biofilter gave the best performance for color and DOC removal, but some of this enhanced performance was caused by adsorption, since the GAC was virgin at the beginning of the pilot studies. Backwashing events had no noticeable impact of the performance of the biofilters. The Transient-State, Multiple-Species Biofilm Model (TSMSBM) was used to interpret the experimental results. Model simulations show that soluble microbial products, which comprised a significant part of the effluent BOM, offset the removal of original BOM, a factor that kept the removal of DOC relatively constant over the range of EBCTs of 3.5-9 min. Although improved biofilm retention, represented by a small detachment rate, allowed more total biofilm accumulation and greater removal of original BOM, it also caused more release of soluble microbial products and the build up of inert biomass in the biofilm. Backwashing had little impact on biofilter performance, because it did not remove more than 25% of the biofilm under any condition simulated.     

Accumulation and fate of green fluorescent labeled Escherichia coli in laboratory-scale drinking water biofilters

Biological filters combining microbial activity and rapid sand filtration are used in drinking water treatment plants for enhanced biodegradable organic matters (BOM) removal. Biofilms formed on filter media comprised of bacteria enclosed in a polymeric matrix are responsible for the adsorption of BOM and attachment of planktonic microorganisms. This study investigated the removal of Escherichia coli cells injected into laboratory-scale biofilters and the role of biofilm in retaining the injected E. coli. Green fluorescent protein was used as a specific marker to detect and quantify E. coli in the biofilms. About 35% of the total injected E. coli cells were observed in the filter effluents, when initial cell concentrations were measured at 7.4 x 10(6) CFU/mL and 1.6 x 10(7) CFU/mL in two separate experiments. The results from real-time PCR and plate count analysis indicated that 95% of the E. coli retained inside the filters were either non-viable or could not be recovered by colony counting techniques. Injected cells were unevenly distributed inside the filter with more than 70% located at the top 1/5 of the filter. Images obtained from an epifluorescent microscope showed that E. coli cells were embedded inside the biofilm matrix and presented mainly as microcolonies intertwined with other microorganisms, which was consistent with findings from standard plate count methods and qPCR.     

Non-steady state simulation of BOM removal in drinking water biofilters: model development

A numerical model was developed to simulate the non-steady-state behavior of biologically-active filters used for drinking water treatment. The biofilter simulation model called "BIOFILT" simulates the substrate (biodegradable organic matter or BOM) and biomass (both attached and suspended) profiles in a biofilter as a function of time. One of the innovative features of BIOFILT compared to previous biofilm models is the ability to simulate the effects of a sudden loss in attached biomass or biofilm due to filter backwash on substrate removal performance. A sensitivity analysis of the model input parameters indicated that the model simulations were most sensitive to the values of parameters that controlled substrate degradation and biofilm growth and accumulation including the substrate diffusion coefficient, the maximum rate of substrate degradation, the microbial yield coefficient, and a dimensionless shear loss coefficient. Variation of the hydraulic loading rate or other parameters that controlled the deposition of biomass via filtration did not significantly impact the simulation results.     

Biofiltration for removal of BOM and residual ammonia following control of bromate formation

Nitrification was developed within a biological filter to simultaneously remove biodegradable organic matter (BOM) and residual ammonia added to control bromate formation during the ozonation of drinking water. Testing was performed at pilot-scale using three filters containing sand and anthracite filter media. BOM formed during ozonation (e.g., assimilable organic carbon (396-572 microg/L), formaldehyde (11-20 microg/L), and oxalate (83-145 microg/L)) was up to 70% removed through biofiltration. Dechlorinated backwash water was required to develop the nitrifying bacteria needed to convert the residual ammonia (0.1-0.5 mg/L NH(3)-N) to nitrite and then to nitrate. Chlorinated backwash water resulted in biofiltration without nitrification. Deep-bed filtration (empty-bed contact time (EBCT) = 8.3 min) did not enhance the development of nitrification when compared with shallow-bed filtration (EBCT = 3.2 min). Variable filtration rates between 4.8 and 14.6 m/h (2 and 6 gpm/sf) had minimal impact on BOM removal. However, conversion of ammonia to nitrite was reduced by 60% when increasing the filtration rate from 4.8 to 14.6 m/h. The results provide drinking water utilities practicing ozonation with a cost-effective alternative to remove the residual ammonia added for bromate control.     

Development of biomass in a drinking water granular active carbon (GAC) filter

Indigenous bacteria are essential for the performance of drinking water biofilters, yet this biological component remains poorly characterized. In the present study we followed biofilm formation and development in a granular activated carbon (GAC) filter on pilot-scale during the first six months of operation. GAC particles were sampled from four different depths (10, 45, 80 and 115 cm) and attached biomass was measured with adenosine tri-phosphate (ATP) analysis. The attached biomass accumulated rapidly on the GAC particles throughout all levels in the filter during the first 90 days of operation and maintained a steady state afterward. Vertical gradients of biomass density and growth rates were observed during start-up and also in steady state. During steady state, biomass concentrations ranged between 0.8-1.83 x 10⁻⁶ g ATP/g GAC in the filter, and 22% of the influent dissolved organic carbon (DOC) was removed. Concomitant biomass production was about 1.8 × 10¹² cells/m²h, which represents a yield of 1.26 × 10⁶ cells/μg. The bacteria assimilated only about 3% of the removed carbon as biomass. At one point during the operational period, a natural 5-fold increase in the influent phytoplankton concentration occurred. As a result, influent assimilable organic carbon concentrations increased and suspended bacteria in the filter effluent increased 3-fold as the direct consequence of increased growth in the biofilter. This study shows that the combination of different analytical methods allows detailed quantification of the microbiological activity in drinking water biofilters.     

Removal of easily biodegradable organic compounds by drinking water biofilms: analysis of kinetics and mass transfer

This paper evaluates the rate of utilization of easily biodegradable organic compounds by drinking water biofilms. Tap water, which had been filtered through biologically active granular activated carbon, was used as an innoculum for biofilm growth in annular reactors (ARs). Synthetic cocktails of easily biodegradable material in the concentration range of 50-2,000 mgC/m3 were used as substrate for biofilm growth. Influent and effluent aggregate concentrations of biodegradable organic matter (BOM) were calculated by adding the measurable BOM components on a mass carbon basis. The aggregate BOM values were used for calculating the observed Damk?hler number and Theile modulus (based on a reaction rate per unit surface area), which were used to determine whether external or internal mass transfer limited BOM removal. For all of the experimental trials, it was shown that neither external nor internal mass transfer limited BOM removal. Because the biofilms in this research are thin and the fact that mass transfer is not limiting, it was assumed that the bulk BOM concentration was approximately equal to the average BOM concentration in the biofilm. A linear model was obtained for the aggregate BOM flux and the product of the effluent BOM concentration and the biofilm density. The slope or the areal biodegradation rate (ka) for the aggregate BOM was 0.033 m/h, as determined through a linear regression.     

Membrane coagulation bioreactor (MCBR) for drinking water treatment

In this paper, a novel submerged ultrafiltration (UF) membrane coagulation bioreactor (MCBR) process was evaluated for drinking water treatment at a hydraulic retention time (HRT) as short as 0.5h. The MCBR performed well not only in the elimination of particulates and microorganisms, but also in almost complete nitrification and phosphate removal. As compared to membrane bioreactor (MBR), MCBR achieved much higher removal efficiencies of organic matter in terms of total organic carbon (TOC), permanganate index (COD(Mn)), dissolved organic carbon (DOC) and UV absorbance at 254nm (UV(254)), as well as corresponding trihalomethanes formation potential (THMFP) and haloacetic acids formation potential (HAAFP), due to polyaluminium chloride (PACl) coagulation in the bioreactor. However, the reduction of biodegradable dissolved organic carbon (BDOC) and assimilable organic carbon (AOC) by MCBR was only 8.2% and 10.1% higher than that by MBR, indicating that biodegradable organic matter (BOM) was mainly removed through biodegradation. On the other hand, the trans-membrane pressure (TMP) of MCBR developed much lower than that of MBR, which implies that coagulation in the bioreactor could mitigate membrane fouling. It was also identified that the removal of organic matter was accomplished through the combination of three unit effects: rejection by UF, biodegradation by microorganism and coagulation by PACl. During filtration operation, a fouling layer was formed on the membranes surface of both MCBR and MBR, which functioned as a second membrane for further separating organic matter.     

Improvement of organics removal by bio-ceramic filtration of raw water with addition of phosphorus

The purpose of this study was to investigate the effect of phosphorus addition on biological pretreatment of raw water. Experiments were conducted in pilot-scale bio-ceramic filters with raw water from a reservoir located in Beijing, China. The results demonstrated that phosphorus was the limiting nutrient for bacterial growth in the raw water investigated in this study. The measured values of bacterial regrowth potential (BRP) and biodegradable dissolved organic carbon (BDOC) of the raw water increased by 50-65% and 30-40% with addition of 50 microg of PO4(3-)-PL(-1), respectively. Addition of 25 microg of PO4(3-)-PL(-1) to the influent of bio-ceramic filter enhanced the percent removal of organics by 4.6, 5.7 and 15 percentage points in terms of COD(Mn), TOC and BDOC, respectively. Biomass in terms of phospholipid content increased by 13-22% and oxygen uptake rate (OUR) increased by 35-45%. The ratio of C:P for bacteria growth was 100:1.6 for the raw water used in this study. Since change of phosphorus concentrations can influence the performance of biological pretreatment and the biological stability of drinking water, this study is of substantial significance for waterworks in China. The role of phosphorus in biological processes of drinking water should deserve more attention.     

Rapid and direct estimation of active biomass on granular activated carbon through adenosine tri-phosphate (ATP) determination

Granular activated carbon (GAC) filtration is used during drinking water treatment for the removal of micropollutants such as taste and odour compounds, halogenated hydrocarbons, pesticides and pharmaceuticals. In addition, the active microbial biomass established on GAC is responsible for the removal of biodegradable dissolved organic carbon compounds present in water or formed during oxidation (e.g., ozonation and chlorination) processes. In order to conduct correct kinetic evaluations of DOC removal during drinking water treatment, and to assess the state and performance of full-scale GAC filter installations, an accurate and sensitive method for active biomass determination on GAC is required. We have developed a straight-forward method based on direct measurement of the total adenosine tri-phosphate (ATP) content of a GAC sample and other support media. In this method, we have combined flow-cytometric absolute cell counting and ATP analysis to derive case-specific ATP/cell conversion values. In this study, we present the detailed standardisation of the ATP method. An uncertainty assessment has shown that heterogeneous colonisation of the GAC particles makes the largest contribution to the combined standard uncertainty of the method. The method was applied for the investigation of biofilm formation during the start-up period of a GAC pilot-scale plant treating Lake Zurich water. A rapid increase in the biomass of up to 1.1 x 10(10)cells/g GAC dry weight (DW) within the first 33 days was observed, followed by a slight decrease to an average steady-state concentration of 7.9 x 10(9)cells/g GAC DW. It was shown that the method can be used to determine the biomass attached to the GAC for both stable and developing biofilms.     

Nutrient gradients in a granular activated carbon biofilter drives bacterial community organization and dynamics

The quality of drinking water is ensured by hygienic barriers and filtration steps, such as ozonation and granular activated carbon (GAC) filtration. Apart from adsorption, GAC filtration involves microbial processes that remove biodegradable organic carbon from the ozonated ground or surface water and ensures biological stability of the treated water. In this study, microbial community dynamics in were monitored during the start-up and maturation of an undisturbed pilot-scale GAC filter at 4 depths (10, 45, 80 and 115 cm) over a period of 6 months. New ecological tools, based on 16S rRNA gene-DGGE, were correlated to filter performance and microbial activity and showed that the microbial gradients developing in the filter was of importance. At 10 cm from the top, receiving the freshly ozonated water with the highest concentration of nutrients, the microbial community dynamics were minimal and the species richness remained low. However, the GAC samples at 80-115 cm showed a 2-3 times higher species richness than the 10-45 cm samples. The highest biomass densities were observed at 45-80 cm, which corresponded with maximum removal of dissolved and assimilable organic carbon. Furthermore, the start-up period was clearly distinguishable using the Lorenz analysis, as after 80 days, the microbial community shifted to an apparent steady-state condition with increased evenness. This study showed that GAC biofilter performance is not necessarily correlated to biomass concentration, but rather that an elevated functionality can be the result of increased microbial community richness, evenness and dynamics.     

Using soil biomass as an indicator for the biological removal of effluent-derived organic carbon during soil infiltration

This study investigates the relationship between soil biomass and organic carbon removal during the infiltration of conventionally treated effluents used for groundwater recharge during soil-aquifer treatment (SAT). Investigations were conducted on samples collected from full-scale SAT sites, revealing a positive correlation between biodegradable organic carbon (BOC) concentrations in the recharged effluents and total viable soil biomass concentrations in the infiltration zone of soil samples collected from respective recharge basins. Findings of this study suggest that BOC limits soil biomass growth and was able to support a steady-state concentration of viable soil biomass that is characteristic to BOC concentrations introduced with the recharged effluents. All investigated sites indicate that BOC is primarily removed within 30 cm soil depth leading to a significant increase in soil biomass levels (measured as substrate induced respiration (SIR), total viable biomass, and dehydrogenase activity (DHA)). Controlled biological column studies revealed that the primary components of BOC in domestic effluents are organic colloids. Findings of this study support that hydrophobic acids, commonly believed to be recalcitrant, may also be attenuated by biological processes during soil infiltration.     

饮用水生物强化过滤工艺生物膜特性研究

以水厂沉淀池出水为原水,对生物强化过滤工艺的生物膜形成过程进行了研究,探讨了不同滤料介质组成的生物滤柱的生物膜特性,分析了膜形成过程中污染物的去除效果和滤柱生物量的变化情况,并对膜形成过程的影响因素进行了讨论.结果表明,在活性炭-石英砂滤料上生物膜形成效果要优于无烟煤-石英砂双层滤料和石英砂单层滤料;反冲洗水含氯对生物膜形成有负面影响,对无烟煤-石英砂滤柱的影响尤为显著;可以CODMn和NO-2的去除率作为生物膜成熟的评价指标.     

Ozonation effect on natural organic matter adsorption and biodegradation - Application to a membrane bioreactor containing activated carbon for drinking water production

More stringent legislation on dissolved organic matter (DOM) urges the drinking water industry to improve in DOM removal, especially when applied to water with high dissolved organic carbon (DOC) contents and low turbidity. To improve conventional processes currently used in drinking water treatment plants (DWTPs), the performances of a hybrid membrane bioreactor containing fluidised activated carbon were investigated at the DWTP of Rennes. Preliminary results showed that the residual DOC was the major part of the non-biodegradable fraction. In order to increase the global efficiency, an upstream oxidation step was added to the process. Ozone was chosen to break large molecules and increase their biodegradability. The first step consisted of carrying out lab-scale experiments in order to optimise the necessary ozone dose by measuring the process yield, in terms of biodegradable dissolved organic carbon (BDOC). Secondly, activated carbon adsorption of the DOC present in ozonated water was quantified. The whole process was tested in a pilot unit under field conditions at the DWTP of Rennes (France). Lab-scale experiments confirmed that ozonation increases the BDOC fraction, reduces the aromaticity of the DOC and produces small size organic compounds. Adsorption tests led to the conclusion that activated carbon unexpectedly removes BDOC first. Finally, the pilot unit results revealed an additional BDOC removal (from 0.10 to 0.15 mg L⁻¹) of dissolved organic carbon from the raw water considered.     

Evaluation of biodegradability of NOM after ozonation

The major purpose of this study was to develop a simple procedure to describe the kinetics of biodegradation of natural organic matter (NOM) in drinking water and to use this procedure to evaluate changes in the concentration of biodegradable organic matter during ozonation and biotreatment. The proposed approach quantitatively describes the formation and removal of rapidly and slowly biodegradable fractions of NOM. This study showed that, depending on source water, ozonation of NOM may result in either minimal formation of biodegradable organic carbon (BDOC), or the formation of predominantly rapidly biodegradable NOM, or in the formation of both rapidly and slowly biodegradable NOM. The kinetic data obtained in this study suggest that while conventional biofiltration processes are capable of removing the rapidly biodegradable fraction, slowly biodegradable organic matter would remain in the filter effluent and may cause bacterial regrowth in the distribution system. An addition of a small amount of easily biodegradable carbon ("stimulated" biodegradation) to ozonated water appears to be effective for the removal of slowly biodegradable organic matter.     

Comparison of methods for the measurement of biodegradable organic carbon and assimilable organic carbon in water

In the last few years different methods for determining assimilable organic carbon (AOC) and biodegradable dissolved organic carbon (BDOC) in drinking water have been proposed. However, there is no agreement on the most suitable methods for the assessment of treatment processes. A comparison of six methods, one for AOC(P17) determination and five for BDOC determination, using water samples taken at different steps in a water-treatment process in Sant Joan Despí (Barcelona, Spain) is reported. Results show that the biodegradable matter values given by AOC measurements are substantially lower than those obtained using BDOC methods. The various BDOC methods do not differ significantly in their results.     

Measurement of streamwater biodegradable dissolved organic carbon with a plug-flow bioreactor

Plug-flow biofilm reactors were colonized by microorganisms indigenous to streamwater and used to measure concentrations of biodegradable dissolved organic carbon (DOC) in streamwater. We performed experiments to determine the influence of physical, chemical, and biological factors on the operation of the bioreactors. Colonization required several months and the biological removal of DOC within the reactors was influenced by hydraulic residence time, dissolved organic carbon concentration, and water temperature. The large microbial biomass within a bioreactor buffered bioreactor performance from changes in chemical and physical parameters.     

Biomass development in slow sand filters

Microbial biomass development in the sand and schmutzdecke layer was determined in two full-scale slow sand filters, operated with and without a light excluding cover. A standard chloroform fumigation-extraction technique was adapted to routinely measure microbial biomass concentrations in the sand beds. Sand was sampled to a depth of 10 cm and schmutzdecke was also collected at the same random positions on the uncovered filter. Interstitial microbial biomass in the uncovered sand bed increased with time and decreased with sampling depth. There was a small accumulation of sand biomass with time in the covered filter, but no relationship was apparent between biomass concentration and depth in this filter. Schmutzdecke did not develop on the covered filter and was spatially highly variable in the uncovered condition compared to the consistent patterns observed in interstitial biomass production. It is speculated that microbial biomass in the sand of uncovered filters is largely related to carbon inputs from photosynthetic activity in the schmutzdecke and involves mechanisms that spatially distribute carbon substrate from the schmutzdecke to the sand. However, total organic carbon and dissolved organic carbon removals were similar in both filters suggesting that relatively small biomass populations in covered filters are sufficient to remove residual labile carbon during advanced water treatment and little further advantage to water purification and organic carbon removal is gained by the increased production of biomass in uncovered slow sand filter beds.     

Removal of MIB and geosmin using granular activated carbon with and without MIEX pre-treatment

This study assessed the impact of MIEX pre-treatment, followed by either coagulation or microfiltration (MF), on the effectiveness of pilot granular activated carbon (GAC) filters for the removal of the taste and odour compounds, 2-methylisoborneol (MIB) and geosmin, from a surface drinking water source over a 2-year period. Complete removal of MIB and geosmin was achieved by all GAC filters for the first 10 months, suggesting that the available adsorption capacity was sufficient to compensate for differences in dissolved organic carbon (DOC) entering the GAC filters.Reduction of empty bed contact time (EBCT), in all but one GAC filter, resulted in breakthrough of spiked MIB and geosmin, with initial results inconclusive regarding the impact of MIEX pre-treatment. MIB and geosmin removal increased over the ensuing 12 months until complete removal of both MIB and geosmin was again achieved in all but one GAC filter, which had been pre-chlorinated. Autoclaving and washing the GAC filters had minimal impact on geosmin removal but reduced MIB removal by 30% in all but the pre-chlorinated filter, confirming that biodegradation impacted MIB removal. The impact of biodegradation was greater than any impact on GAC adsorption arising from DOC differences due to MIEX pre-treatment. It is not clear whether, at a lower initial EBCT, MIEX pre-treatment may have impacted on the adsorption capacity of the virgin GAC.The GAC filter maintained at the longer EBCT, which was also pre-chlorinated, completely removed MIB and geosmin for the period of the study, suggesting that the greater adsorption capacity was compensating for any decrease in biological degradation.     

Estimating nitrifying biomass in drinking water filters for surface water treatment

The objective of this work is to estimate active nitrifying biomass and its main influencing factors in low-loaded biofilters based on operational data. An analytical approach based on balancing growth, decay and biomass removed by backwashing is proposed. The method is developed and applied in pilot-scale rapid sand filters for drinking water treatment. Decay rate was measured directly in the filter for different temperatures. To assess the amount of active biomass in backwash water, a technique based on respiration measurements was used. Backwash losses increased overproportional with balanced biomass in the filter. The impact of both parameters on active biomass is quantified exemplarily for a given constant nitrification rate.