Solvothermal preparation and characteristics of Sn-doped In2O3

Sn-doped 111203 (ITO) nanopowders were prepared in ethanol solvent by solvothermal process.The effects of the solvothermal temperature,coprecipitation pH value and SnO2 content on the products phase and microwave absorption were investigated by X-ray diffractometry and microwave reflectance.ITO nanopowders with cubic structure can be respectively prepared at 250 and 270 ℃ for 6 h.The prepared product is InOOH or the mixture of InOOH and In3Sn4O12 when the solvothermal temperature is below 250℃.With rising solvothermal temperature and prolonging time,the absorption of the ITO powders gradually decreases.The products are ITO nanopowders by coprecipitating at pH=9 or 11,but ITO powders with Sn3O4 at pH=6.The absorption of powders prepared at pH=6 is better than that at any other pH value.The products are all ITO nanopowders and crystal size reduces with increasing SnO2 content.The microwave absorption of ITO nanopowders with SnO2 content of 8% (mass fraction)is the best among samples with different SnO2 contents.     

Effects of In2O3 doping and sintering temperature on the electrical properties of ZnO varistors

ZnO varistors are prepared using the 0.1–0.3 mm ZnO powders. The effects of the sintering temperature, contents of In₂O₃ doping on the non-linear properties of ZnO varistors have been investigated. The results show that this kind of ZnO powder has a high sintering activity. It is suitable for making the low voltage varistors. The V _c decreases with the increase of sintered temperature, when the In₂O₃ content is fixed (0.98%, mass fraction), and increases with the increase of In₂O₃ contents when the temperature is steady. Project supported by the Nonferrous Metals Industry Corporation of China Synopsis of the first anthor Zhao Ruirong, born in Jan. 1935, majoring in nonferrous metal metallurgy and products exploition.     

Preparation and properties of 4.25Cu-0.75Ni／NiFe2O4 cermet

4.25Cu-0.75Ni/NiFe₂O₄ cermets were prepared by doping NiFe₂O₄ ceramic matrix with the mixed powders of Cu and Ni or Cu-Ni alloy powder as the electrical conducting metallic elements. The effects of technological parameters, such as the adding modes of metallic elements, the ball milling time, the sintering time and the sintering temperature, on the relative density and resistivity of the cermets were studied. The results show that the resistivity of 4.25Cu-0.75Ni/NiFe₂O₄ cermets decreases with increasing temperature, and has a turning point at 590 °C, which is similar to that of NiFe₂O₄ ceramic. The sintering temperature and adding modes of metallic elements have a great influence on the properties of 4.25Cu-0.75Ni/NiFe₂O₄ cermets. When the sintering temperature increases from 1200 °C to 1300 °C, the relative density increases from 89.86% to 95.33%, and the resistivity at 960 °C decreases from 0.11 Ω · cm to 0.03 Ω · cm, respectively. When the metallic elements are added with the mixed powders of Cu and Ni, the cermets of finely and uniformly dispersed metallic phase, high density and electric conductivity are obtained. The relative density and resistivity at 960 °C are 90.23% and 0.04 Ω · cm respectively for the cermet samples sintered at 1200 °C for 2 h, which are both better than those of the cermets prepared under the same technique conditions but with the metallic elements added as 85Cu-15Ni alloy powders. Foundation item: Project (G1999064903) supported by the National Key Fundamental Research and Development Program of China; project(2001AA335013) supported by the National High Technology Research and Development Program of China; project (50204014) supported by the National Natural Science Foundation of China     

Preparation and structure characteristics of nano-Bi2O3 powders with mixed crystal structure

The nano-Bi2O3 powders were prepared by a chemical precipitation method with Bi(NO3)3, HNO3 and NaOH as reactants. The structural characteristics and morphology of nano-Bi2O3 powders were investigated by X-ray diffraction and transmission electron microscopy, respectively. The results show that under the optimum condition that 300g/L Bi(NO3)3 reacts at 90℃ for 2 h, the Bi203 powders with 60 nm on the average and 99.5% in purity are obtained. The prepared nano-Bi2O3 powders contain a mixed crystal structure of monoclinic and triclinic instead of traditional structure of monoclinic α-Bi2O3. And the mixed crystal structure is stable in air. The reason for the appearance of the mixed crystal structure may be that the ionic radius ratio of Bi^3 to O^2- changes easily during the formation of nano-Bi2O3 particles by a chemical precipitation method.     

Modification of nano-TiO2 by Al2O3 in-situ coating

A novel technology of in-situ coating Al₂O₃ on the surface of H₄TiO₄ was developed to prevent the aggregation of nano-TiO₂ powders and improve the dispersibility and thermal stability in the way of forming a uniform coating layer. The heterogeneous nucleation was conducted to prepare the precursor of nano-TiO₂ and then Al₂O₃ was coated on the surface of precursor. The effects of Al₂O₃ in-situ coating on the properties of nano-TiO₂ were investigated. The results show that H₄TiO₄ can be dispersed well under alkaline condition (pH 8.5) and the heterogeneous nucleation can be controlled easily. The optimized uniform coating layer is obtained by adding 5% (mass fraction) and 10% of Al₂O₃ and the aggregation of nano-TiO₂ powders is effectively inhibited and the dispersibility is obviously improved. The crystal sizes of TiO₂ powders are 12.3, 11.4 and 8.7 nm after coating 0,5% and 10% of Al₂O₃ respectively. Al₂O₃ on the surface of particulates in amorphous phase could increase the thermal stability of nano-particles after calcined at 550 °C. Foundation item: Project(04GK2007) supported by Hunan Industrial Key Project of Science and Technology     

Pressureless sintered 3Y-TZP/20%Al2O3 composite ceramic

Nanometer 3Y-TZP/20%Al₂O₃ (mass fraction) composite powders prepared by the chemical coprecipitation method were pressureless sintered at 1550 °C for 2 h. Effects of calcining temperatures at 800 °C, 1 000 °C, and 1 200 °C on phase structure, relative density, and Vicker’s hardness of the sintered bodies were studied. The results show that 1 000 °C was the optimal calcining temperature, and the powder calcined was composed of tetragonal zirconia with the Scherrer crystalline size of 6.3nm. The relative density was up to 98.5% under pressureless sintering, and the sintered body was t-ZrO₂ (without m-ZrO₂)+α-Al₂O₃ with the average size of 0.4 μm. Foundation item: State Key Laboratory for Powder Metallurgy(No.9706-36) Biography of the first author: YIN Bang-yao, born in 1966, majoring in advanced ceramic materials.     

Synthesis and characterization of high-voltage cathode material LiNi0.5Mn1.5O4 by one-step solid-state reaction

LiNi_0.5Mn_1.5O₄ was prepared under various conditions by one-step solid-state reaction in air and its properties were investigated by X-ray diffractormetry (XRD), scanning electron microscopy (SEM) and electrochemical measurement. XRD patterns show that LiNi_0.5Mn_1.5O₄ synthesized under various conditions has cubic spinel structure. SEM images exhibit that the particle size increases with increasing calcination temperature and time. Electrochemical test shows that the LiNi_0.5Mn_1.5O₄ calcined at 700 °C for 24 h delivers up to 143 mA · h/g, and the capacity retains 132 mA · h/g after 30 cycles. Foundation item: Project (76600) supported by Postdoctoral Science Foundation of Central South University     

Characteristics of LiCoO2, LiMn2O4 and LiNi0.45Co0.1Mn0.45O2 as cathodes of lithium ion batteries

LiNi_0.45Co_0.10Mn_0.45O₂ was synthesized from Li₂CO₃ and a triple oxide of nickel, cobalt and manganese at 950 °C in air. The structures and characteristics of LiNi_0.45Co_0.10Mn_0.45O₂, LiCoO₂ and LiMn₂O₄ were investigated by XRD, SEM and electrochemical measurements. The results show that LiNi_0.45Co_0.10Mn_0.45O₂ has a layered structure with hexagonal lattice. The commercial LiCoO₂ has sphere-like appearance and smooth surfaces, while the LiMn₂O₄ and LiNi_0.45Co_0.10Mn_0.45O₂ consist of cornered and uneven particles. LiNi_0.45Co_0.10Mn_0.45O₂ has a large discharge capacity of 140.9 mA · h/g in practical lithium ion battery, which is 33.4% and 2.8% above that of LiMn₂O₄ and LiCoO₂, respectively. LiCoO₂ and LiMn₂O₄ have higher discharge voltage and better rate-capability than LiNi_0.45Co_0.10Mn_0.45O₂. All the three cathodes have excellent cycling performance with capacity retention of above 89.3% at the 250th cycle. Batteries with LiMn₂O₄ or LiNi_0.45Co_0.10Mn_0.45O₂ cathodes show better safety performance under abusive conditions than those with LiCoO₂ cathodes. Foundation item: Project(50302016) supported by the National Natural Science Foundation of China; Project(2005037698) supported by the Postdoctoral Science Foundation of China     

Effects of drying method on preparation of nanometer α-Al2O3

Ammonium aluminum carbonate hydroxide （AACH） precursor was synthesized by the precipitation reaction of aluminum sulfate and ammonium carbonate. Then the precursor was dealt with five drying methods including ordinary drying, alcohol exchange, vacuum freeze-drying, glycol distillation, n-butanol azeotropic distillation respectively and calcined at 1 200℃ for 2 h to get α-Al2O3. The effects of drying methods on preparation of nanometer α-Al2O3 were discussed, and the optimal drying method was confirmed. The structural properties of powders were characterized by XRD, SEM and BET measurements. The results show that vacuum freeze-drying, glycol distillation and n-butanol azeotropic distillation can prevent the powders from aggregating, and among them the n-butanol azeotropic distillation is the best method. The nanometer α-Al2O3 powder with non-aggregation can be manufactured using n-butanol azeotropic distillation and the average particle size is about 40 nm.     

Properties of plasma sprayed NiCrAlY+(ZrO2+Y2O3) coating on refractory steel surface

NiCrAlY+(ZrO₂+Y₂O₃) thermal barrier coating was prepared on the surface of refractory steel 1Cr18Ni9Ti with plasma spraying technique. The phases and microstructure of the thermal barrier coating were determined by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The results show that the bonding between thermal barrier coating and substrate is sound. The surface hardness of 1Cr18Ni9Ti reaches up to 1 000 HV, but that of substrate is only 300 HV. The patterns sprayed with CoNiCrAlY+(ZrO₂+Y₂O₃) ceramic coating have a good heat insulation effect at 800 °C for heat insulation temperature difference reaches 54 °C, which increases the operating temperature and service life of refractory steel. Foundation item: Project (5040202140) supported by Scientific Research Common Program of Beijing Municipal Commission of Education     

球形LiMn1.5Ni0.5O4材料的嵌脱动力学

为明晰Li Mn1.5Ni0.5O4正极材料的动力学性能,采用水热辅助共沉淀法合成了尖晶石Li Mn1.5Ni0.5O4正极材料,并采用扫描电镜(SEM)、X射线粉末衍射(XRD)和电化学阻抗(EIS)研究了材料的结构和锂离子嵌脱动力学.实验结果表明:共沉淀法制备的Li Ni0.5Mn1.5O4材料颗粒呈均匀球形,且平均粒径较小,粒度分布较窄.在循环过程中,Li Ni0.5Mn1.5O4的电荷转移电阻增大,锂离子扩散系数减小,进而电子电导率和离子电导率下降.温度升高后,Li Ni0.5Mn1.5O4材料的溶液电阻变化不大,但是电荷转移电阻逐渐增大,锂离子扩散系数逐渐减小;此外,随着温度的升高,Li Ni0.5Mn1.5O4材料的溶解速度加快,从而导致SEI膜的厚度增大.Li Ni0.5Mn1.5O4材料的嵌脱锂动力学与温度和循环次数有密切关系.     

Luminescent properties of BaO-La2O3-B2O3 glasses with dopant

The luminescent properties of glasses synthesized in air atmosphere by conventional high temperature process were stud{ed. The emissions spectra of Eu^2 and Eu^3 were observed in BaO-La2O3-B2O3-Eu2O3 glasses.The results show that the broad emission peaks at 430 nm correspond to 5d→4f emission transition of Eu^2 , the sharp emission peaks at 592, 616, 650 and 250 nm correspond to 5^D0→1Fj(j=1--4) emission transition of Eu^3 ,respectively, which indicates that the BaO-La2O3a-B2O3-Eu2O3 glass can convert ultraviolet and green omponents of sunlight into blue and red light so as to increase the intensity of blue and red light, respectively. The luminescent in--tensity of Eu^2 increases with increasing the molar ratio of Tb^3 in BaO-La2O3-B2O3-Eu2O3a-Tb4O3 glasses, whereas the luminescent intensity of Eua^3 decreases. So the luminescent intensity of Eu(Ⅲ,Ⅱ) is influenced by Tb^3 .These phenomena can be explained by electron transfer mechanism; Eu^3 (4f6) Tb^3 (4f^8)→Eu^2 (4f′) Tb^4 (4f′). Taking advantage of the luminescent properties of BaO-La2O3-B2O3-Eu2O3 glasses, light-conversion glass for agriculture can be produced.     

Preparation of LiFePO4 for lithium ion battery using Fe2P2O7 as precursor

In order to obtain a new precursor for LiFePO4, Fe2P2O7 with high purity was prepared through solid phase reaction at 650 ℃ using starting materials of FeC2O4 and NH4H2PO4 in an argon atmosphere. Using the as-prepared Fe2P2O7, Li2CO3 and glucose as raw materials, pure LiFePO4 and LiFePO4/C composite materials were respectively synthesized by solid state reaction at 700 ℃ in an argon atmosphere. X-ray diffractometry and scanning electron microscopy（SEM） were employed to characterize the as-prepared Fe2P2O7, LiFePO4 and LiFePO4/C. The as-prepared Fe2P2O7 crystallizes in the Cl space group and belongs to β-Fe2P2O7 for crystal phase. The particle size distribution of Fe2P2O7 observed by SEM is 0.4-3.0 μm. During the Li^＋ ion chemical intercalation, radical P2O7^4- is disrupted into two PO4^3- ions in the presence of O^2-, thus providing a feasible technique to dispose this poor dissolvable pyrophosphate. LiFePO4/C composite exhibits initial charge and discharge capacities of 154 and 132 mA·h/g, respectively.     

Preparation of ITO nano-powders by hydrothermal-calcining process

1 INTRODUCTIONSn-doped In2O3(ITO) is one kind of n-typesemiconductor material[1].It has excellent electro-optical properties , such as electrical conductivityand high transparency under visible light[2],andiswidely used in electronic , transparent electrode ,solar cells and electro-irradiance , especially inscreen display[3 ,4].Recently nearly half of the met-al indium has been used to prepare ITO materialsin the developed countries[5], such as Japan, A-merica ,France and so on.So the…     

Molar heat capacities of La2Mo2O9 and La1.9Sr0.1MO209-δ

The molar heat capacities of La2Mo209 and La1.9Sr0.1MO209-δ were obtained using the differential scanning calorimetry （DSC） technique in a temperature range from 298 to 1473 K. The DSC curve of La2Mo209 showed an endothermal peak around 834 K corresponding to a first-order monoclinic-cubic phase transition, and the enthalpy change accompanying this phase transition is 5.99 kJ/mol. No evident endothermal peak existed in the DSC curve of La1.9Sr0.1MO209-δ, but a broad thermal anomaly existed in its heat capacity curve at around 832 K. In addition, the heat capacity values of La2Mo209 and La1.9Sr0.1MO209-δ began to decrease at 1196 and 1330 K, respectively. The non-transitional heat capacity values of La2Mo209 and La1.9Sr0.1MO209-δ were formulated using multiple regression analysis in two temperature ranges.     

Ferroelectric properties of Bi3.4Ho0.6Ti3O12 thin films prepared by sol-gel method

We have prepared the Ho-substituted bismuth titanate (Bi_3.4Ho_0.6Ti₃O₁₂, BHT) thin films on Pt/Ti/SiO₂/Si substrates using sol-gel method. The crystal structure and morphology of the films were characterized using X-ray diffraction and atomic force microscopy. The BHT film shows a single phase of Bi-layered Aurivillius structure and dense microstructure. The 2Pr and 2Ec of the 600-nm-thick BHT film were 38.4 μC/cm² and 376.1 kV/cm, respectively at applied electric field 500 kV/cm. The dielectric constant and dielectric loss are about 310 and 0.015 at a frequency of 1 MHz, respectively. The Pr value decreased to 93% of its pre-fatigue values after 4.46×10⁹ switching cycles at 1 MHz frenquency, and the BHT film shows good insulating behavior according to the test of leakage current. Supported by the Hubei Province Natural Science Foundation (Grant No. 2007ABA309)     

Synthesis and characterization of Mg3(PO4)2-coated Li1.05Ni1/3Mn1/3Co1/3O2 cathode material for Li-ion battery

Mg₃(PO₄)₂-coated Li_1.05Ni_1/3Mn_1/3Co_1/3O₂ cathode materials were synthesized via co-precipitation method. The morphology, structure, electrochemical performance and thermal stability were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), cyclic voltammetry(CV), electrochemical impedance spectroscopy(EIS), charge/discharge cycling and differential scanning calorimeter (DSC). SEM analysis shows that Mg₃(PO₄)₂-coating changes the morphologies of their particles and increases the grains size. XRD and CV results show that Mg₃(PO₄)₂-coating powder is homogeneous and has better layered structure than the bare one. Mg₃(PO₄)₂-coating improved high rate discharge capacity and cycle-life performance. The reason why the cycling performance of Mg₃(PO₄)₂-coated sample at 55 °C was better than that of room temperature was the increasing of lithium-ion diffusion rate and charge transfer rate with temperature rising. Mg₃(PO₄)₂-coating improved the cathode thermal stability, and the result was consistent with thermal abuse tests using Li-ion cells: the Mg₃(PO₄)₂ coated Li_1.05Ni_1/3Mn_1/3Co_1/3O₂ cathode did not exhibit thermal runaway with smoke and explosion, in contrast to the cells containing the bare Li_1.05Ni_1/3Mn_1/3Co_1/3O₂. Funded by the National Natural Science Foundation of China (No. 20273047)     

Synthesis of γ-Al2O3 nanoparticles by chemical precipitation method

Highly pure active γ-Al₂O₃ nanoparticles were synthesized from aluminum nitrate and ammonium carbonate with a little surfactant by chemical precipitation method. The factors affecting the synthesis process were studied. The properties of γ-Al₂O₃ nanoparticles were characterized by DTA, XRD, BET, TEM, laser granularity analysis and impurity content analysis. The results show that the amorphous precursor Al(OH)₃ sols are produced by using 0.1 mol/L Al(NO₃)₃ · 9H₂O and 0.16 mol/L (NH₄)₂CO₃ · H₂O reaction solutions, according to the volume ratio 1.33, adding 0.024% (volume fraction) surfactant PEG600, and reacting at 40 °C, 1 000 r/min stirring rate for 15 min. Then, after stabilizing for 24 h, the precursors were extracted and filtrated by vacuum, washed thoroughly with deionized water and dehydrated ethanol, dried in vacuum at 80°C for 8 h, final calcined at 800 °C for 1 h in the air, and high purity active γ-Al₂O₃ nanoparticles can be prepared with cubic in crystal system, O _H ⁷ -FD3M in space group, about 9 nm in crystal grain size, about 20 nm in particle size and uniform size distribution, 131. 35 m²/g in BET specific surface area, 7 – 11 nm in pore diameter, and not lower than 99.93% in purity. Foundation item: Project(03JJY3015) supported by the Natural Science Foundation of Hunan Province     

Kinetic study of LiMn2O4 in process of lithium intercalation

Exchange current density of spinel LiMn₂O₄ was studied by linear polarization. The relationship of the kinetic property with the structure of spinel LiMn₂O₄ was investigated by studying the effect of the doping and surface coating on the kinetic properties of electrode material. The results show that the exchange current density of spinel LiMn₂O₄ electrode increases with the increase of the amount for lithium intercalation at first, and then decreases. The maximal exchange current density appeares at the 80%–90% lithium intercalation. The similar phenomenon was observed on the doped spinel LiMn₂O₄ electrode. Doping can enhance the exchange current density of spinel LiMn₂O₄ material. However, the degree of the doping effect varies with the doped element varying. Surface coating can also enhance the exchange current density of spinel material, and the increment of value is higher than that of doped ones. Foundation item: Project(50302016) supported by the National Natural Science Foundation of China     

Influence of oxides on high velocity arc sprayed Fe-Al／Cr3C2 composite coatings

Fe-Al/Cr3C2 coatings were sprayed on low steel by high velocity arc spraying(HVAS) technology. The influences of oxides on erosion, corrosion and wear behavior for high velocity arc sprayed Fe-Al/Cr3C2 coatings were studied. The results show that HVAS-sprayed Fe-Al/Cr3C2 coatings have good erosion, heat corrosion and wear resistance. The erosion resistance improves with the increase of the temperature. On one hand, the ferrous oxides are incompact, so they peel off the surface of the coatings easily during the high temperature erosion. On the other hand, compact Al2O3 films on the surface can protect the coatings.