一种片上变压器为负载的用于0.13 μm CMOS工艺2.4GHz WLAN的接收机射频前端电路

A 2.4 GHz radio frequency receiver front end with an on-chip transformer compliant with IEEE 802.11b/g standards is presented. Based on zero-IF receiver architecture, the front end comprises a variable gain common-source low noise amplifier with an on-chip transformer as its load and a high linear quadrature folded Gilbert mixer. As the load of the LNA, the on-chip transformer is optimized for lowest resistive loss and highest power gain. The whole front end draws 21 mA from 1.2 V supply, and the measured results show a double side band noise figure of 3.75 dB, -31 dBm IIP3 with 44 dB conversion gain at maximum gain setting. Implemented in 0.13 μ m CMOS technology, it occupies a 0.612 mm² die size.     

A RF receiver frontend for SC-UWB in a 0.18-μm CMOS process

正A radio frequency(RF) receiver frontend for single-carrier ultra-wideband(SC-UWB) is presented. The front end employs direct-conversion architecture,and consists of a differential low noise amplifier(LNA),a quadrature mixer,and two intermediate frequency(IF) amplifiers.The proposed LNA employs source inductively degenerated topology.First,the expression of input impedance matching bandwidth in terms of gate-source capacitance, resonant frequency and target S_(11) is given.Then,a noise figure optimization strategy under gain and power constraints is proposed,with consideration of the integrated gate inductor,the bond-wire inductance,and its variation.The LNA utilizes two stages with different resonant frequencies to acquire flat gain over the 7.1-8.1 GHz frequency band,and has two gain modes to obtain a higher receiver dynamic range.The mixer uses a double balanced Gilbert structure.The front end is fabricated in a TSMC 0.18-/im RF CMOS process and occupies an area of 1.43 mm~2.In high and low gain modes,the measured maximum conversion gain are 42 dB and 22 dB,input 1 dB compression points are -40 dBm and -20 dBm,and S_(11) is better than -18 dB and -14.5 dB.The 3 dB IF bandwidth is more than 500 MHz.The double sideband noise figure is 4.7 dB in high gain mode.The total power consumption is 65 mW from a 1.8 V supply.     

Design and optimization of a 2.4 GHz RF front-end with an on-chip balun

A 2.4 GHz low-power,low-noise and highly linear receiver front-end with a low noise amplifier(LNA) and balun optimization is presented.Direct conversion architecture is employed for this front-end.The on-chip balun is designed for single-to-differential conversion between the LNA and the down-conversion mixer,and is optimized for the best noise performance of the front-end.The circuit is implemented with 0.35μm SiGe BiCMOS technology.The front-end has three gain steps for maximization of the input dynamic range.The overall maximum gain is about 36 dB.The double-sideband noise figure is 3.8 dB in high gain mode and the input referred third-order intercept point is 12.5 dBm in low gain mode.The down-conversion mixer has a tunable parallel R-C load at the output and an emitter follower is used as the output stage for testing purposes.The total front-end dissipation is 33 mW under a 2.85 V supply and occupies a 0.66 mm~2 die size.     

具有30dB增益和1-16GHz带宽的CMOS低噪声中频放大器

This paper presents a high-gain wideband low-noise IF amplifier aimed for the ALMA front end system using 90-nm LP CMOS technology.A topology of three optimized cascading stages is proposed to achieve a flat and wideband gain.Incorporating an input inductor and a gate-inductive gain-peaking inductor,the active shunt feedback technique is employed to extend the matching bandwidth and optimize the noise figure.The circuit achieves a flat gain of 30.5 dB with 3 dB bandwidth of 1-16 GHz and a minimum noise figure of 3.76 dB.Under 1.2 V supply voltage,the proposed IF amplifier consumes 42 mW DC power.The chip die including pads takes up 0.53 mm~2,while the active area is only 0.022 mm~2.     

A differential low-voltage high gain current-mode integrated RF receiver front-end

A differential low-voltage high gain current-mode integrated RF front end for an 802.11b WLAN is proposed.It contains a differential transconductance low noise amplifier（G_m-LNA） and a differential current-mode 0 down converted mixer.The single terminal of the G_m-LNA contains just one MOS transistor,two capacitors and two inductors.The gate-source shunt capacitors,C_x1 and C_x2,can not only reduce the effects of gate-source C_gs on resonance frequency and input-matching impedance,but they also enable the gate inductance L_g1,2 to be selected at a very small value.The current-mode mixer is composed of four switched current mirrors.Adjusting the ratio of the drain channel sizes of the switched current mirrors can increase the gain of the mixer and accordingly increase the gain of RF receiver front-end.The RF front-end operates under 1 V supply voltage.The receiver RFIC was fabricated using a chartered 0.18μm CMOS process.The integrated RF receiver front-end has a measured power conversion gain of 17.48 dB and an input referred third-order intercept point（IIP3） of-7.02 dBm.The total noise figure is 4.5 dB and the power is only 14 mW by post-simulations.     

A low power 3-5 GHz CMOS UWB receiver front-end

A novel low power RF receiver front-end for 3-5 GHz UWB is presented. Designed in the 0.13μm CMOS process, the direct conversion receiver features a wideband balun-coupled noise cancelling transconductance input stage, followed by quadrature passive mixers and transimpedance loading amplifiers. Measurement results show that the receiver achieves an input return loss below -8.5 dB across the 3.1-4.7 GHz frequency range, maximum voltage conversion gain of 27 dB, minimum noise figure of 4 dB, IIP3 of -11.5 dBm, and IIP2 of 33 dBm. Working under 1.2 V supply voltage, the receiver consumes total current of 18 mA including 10 mA by on-chip quadrature LO signal generation and buffer circuits. The chip area with pads is 1.1 × 1.5 mm^2.     

An RF front-end with an automatic gain control technique for a U/V band CMMB receiver

This paper presents a fully integrated RF front-end with an automatic gain control(AGC) scheme and a digitally controlled radio frequency varied gain amplifier(RFVGA) for a U/V band China Mobile Multimedia Broadcasting(CMMB) direct conversion receiver.The RFVGA provides a gain range of 50 dB with a 1.6 dB step. The adopted AGC strategy could improve immunity to adjacent channel signal,which is of importance for CMMB application.The front-end,composed of a low noise amplifier(LNA),an RFVGA,a mixer and AGC,achieves an input referred 3rd order intercept point(IIP3) of 4.9 dBm with the LNA in low gain mode and the RFVGA in medium gain mode,and a less than 4 dB double side band noise figure with both the LNA and the RFVGA in high gain mode.The proposed RF front-end is fabricated in a 0.35μm SiGe BiCMOS technology and consumes 25.6 mA from a 3.0 V power supply.     

A 5 GHz 7.2 dB NF low power direct conversion receiver front-end with balun LNA

A 5GHz low power direct conversion receiver radio frequency front-end with balun LNA is presented. A hybrid common gate and common source structure balun LNA is adopted,and the capacitive cross-coupling technique is used to reduce the noise contribution of the common source transistor.To obtain low l/f noise and high linearity,a current mode passive mixer is preferred and realized.A current mode switching scheme can switch between high and low gain modes,and meanwhile it can not only perform good linearity but save power consumption at low gain mode.The front-end chip is manufactured on a 0.13-μm CMOS process and occupies an active chip area of 1.2 mm~2.It achieves 35 dB conversion gain across 4.9-5.1 GHz,a noise figure of 7.2 dB and an IIP3 of -16.8 dBm,while consuming 28.4 mA from a 1.2 V power supply at high gain mode.Its conversion gain is 13 dB with an IIP3 of 5.2 dBm and consumes 21.5 mA at low gain mode.     

A multi-mode multi-band RF receiver front-end for a TD-SCDMA/LTE/LTE-advanced in 0.18-μm CMOS process

正A fully integrated multi-mode multi-band directed-conversion radio frequency(RF) receiver front-end for a TD-SCDMA/LTE/LTE-advanced is presented.The front-end employs direct-conversion design,and consists of two differential tunable low noise amplifiers(LNA),a quadrature mixer,and two intermediate frequency(IF) amplifiers.The two independent tunable LNAs are used to cover all the four frequency bands,achieving sufficient low noise and high gain performance with low power consumption.Switched capacitor arrays perform a resonant frequency point calibration for the LNAs.The two LNAs are combined at the driver stage of the mixer,which employs a folded double balanced Gilbert structure,and utilizes PMOS transistors as local oscillator(LO) switches to reduce flicker noise.The front-end has three gain modes to obtain a higher dynamic range.Frequency band selection and mode of configuration is realized by an on-chip serial peripheral interface(SPI) module.The frontend is fabricated in a TSMC 0.18-μm RF CMOS process and occupies an area of 1.3 mm~2.The measured doublesideband (DSB) noise figure is below 3.5 dB and the conversion gain is over 43 dB at all of the frequency bands. The total current consumption is 31 mA from a 1.8-V supply.     

Dual-band RF receiver for GPS-L1 and compass-B1 in a 55-nm CMOS

A fully integrated dual-band RF receiver with a low-IF architecture is designed and implemented for GPS-L 1 and Compass-Bl in a 55-nm CMOS process. The receiver incorporates two independent IF channels with 2 or 4 MHz bandwidth to receive dual-band signals around 1.57 GHz respectively. By implementing a flexible frequency plan, the RF front-end and frequency synthesizer are shared for the dual-band operation to save power consumption and chip area, as well as avoiding LO crosstalk. A digital automatic gain control （AGC） loop is utilized to improve the receiver＇s robustness by optimizing the conversion gain of the analog-to-digital converter （ADC）. While drawing about 20 mA per channel from a 1.2 V supply, this RF receiver achieves a minimum noise figure （NF） of about 1.8 dB, an image rejection （IMR） of more than 35 dB, a maximum voltage gain of about 122 dB, a gain dynamic range of 82 dB, and an maximum input-referred 1 dB compression point of about -36.5 dBm with an active die area of 1.5 × 1.4 mm2 for the whole chip.     

A 14-bit 40-MHz analog front end for CCD application

A 14-bit, 40-MHz analog front end (AFE) for CCD scanners is analyzed and designed. The proposed system incorporates a digitally controlled wideband variable gain amplifier (VGA) with nearly 42 dB gain range, a correlated double sampler (CDS) with programmable gain functionality, a 14-bit analog-to-digital converter and a programmable timing core. To achieve the maximum dynamic range, the VGA proposed here can linearly amplify the input signal in a gain range from -1.08 to 41.06 dB in 6.02 dB step with a constant bandwidth. A novel CDS takes image information out of noise, and further amplifies the signal accurately in a gain range from 0 to 18 dB in 0.035 dB step. A 14-bit ADC is adopted to quantify the analog signal with optimization in power and linearity. An internal timing core can provide flexible timing for CCD arrays, CDS and ADC. The proposed AFE was fabricated in SMIC 0.18 μm CMOS process. The whole circuit occupied an active area of 2.8×4.8 mm² and consumed 360 mW. When the frequency of input signal is 6.069 MHz, and the sampling frequency is 40 MHz, the signal to noise and distortion (SNDR) is 70.3 dB, the effective number of bits is 11.39 bit.     

A 0.18μm CMOS single-inductor single-stage quadrature frontend for GNSS receiver

This paper presents an improved merged architecture for a low-IF GNSS receiver frontend,where the bias current and functions are reused in a stacked quadrature LNA-mixer-VCO.Only a single spiral inductor is implemented for the LC resonator and an extra 1/2 frequency divider is added as the quadrature LO signal generator. The details of the design are presented.The gain plan and noise figure are discussed.The phase noise,quadrature accuracy and power consumption are improved.The test chip is fabricated though a 0.18μm RF CMOS process. The measured noise figure is 5.4 dB on average,with a gain of 43 dB and a IIP3 of-39 dBm.The measured phase noise is better than -105 dBc/Hz at 1 MHz offset.The total power consumption is 19.8 mW with a 1.8 V supply. The experimental results satisfy the requirements for GNSS applications.     

Low power high gain gain-controlled LNA and mixer for GNSS receivers Wei Binbin(魏斌斌)1, Jiang Jinguang(江金光)1,2,3*

A low power high gain gain-controlled LNA ＋ mixer for GNSS receivers is reported. The high gain LNA is realized with a current source load. Its gain-controlled ability is achieved using a programmable bias circuit. Taking advantage of the high gain LNA, a high noise figure passive mixer is adopted. With the passive mixer, low power consumption and high voltage gain of the LNA ＋ mixer are achieved. To fully investigate the performance of this circuit, comparisons between a conventional LNA ＋ mixer, a previous low power LNA ＋ mixer, and the proposed LNA ＋ mixer are presented. The circuit is implemented in 0.18 #m mixed-signal CMOS technology. A 3.8 dB noise figure, an overall 45 dB converge gain and a 10 dB controlled gain range of the two stages are measured. The chip occupies 0.24 mm2 and consumes 2 mA current under 1.8 V supply.     

A 3.1-4.8 GHz CMOS receiver for MB-OFDM UWB

An integrated fully differential ultra-wideband CMOS receiver for 3.1-4.8 GHz MB-OFDM systems is presented. A gain controllable low noise amplifier and a merged quadrature mixer are integrated as the RF front-end. Five order Gm-C type low pass filters and VGAs are also integrated for both I and Q IF paths in the receiver. The ESD protected chip is fabricated in a Jazz 0.18μm RF CMOS process and achieves a maximum total voltage gain of 65 dB, an AGC range of 45 dB with about 6 dB/step, an averaged total noise figure of 6.4 to 8.8 dB over 3 bands and an in-band IIP3 of-5.1 dBm. The receiver occupies 2.3 mm2 and consumes 110 mA from a 1.8 V supply including test buffers and a digital module.     

A low power high gain gain-controlled LNAC＋mixer for GNSS receivers

A low power high gain gain-controlled LNAC+mixer for GNSS receivers is reported. The high gain LNA is realized with a current source load.Its gain-controlled ability is achieved using a programmable bias circuit. Taking advantage of the high gain LNA, a high noise figure passive mixer is adopted. With the passive mixer, low power consumption and high voltage gain of the LNACmixer are achieved. To fully investigate the performance of this circuit, comparisons between a conventional LNAC+mixer, a previous low power LNAC+mixer, and the proposed LNAC+mixer are presented. The circuit is implemented in 0.18 m mixed-signal CMOS technology. A 3.8 dB noise figure, an overall 45 dB converge gain and a 10 dB controlled gain range of the two stages are measured. The chip occupies 0.24 mm2and consumes 2 mA current under 1.8 V supply.     

采用balun低噪声放大器的5GHz 7.2-dB NF低功耗直接转换接收机前端电路

A 5GHz low power direct conversion receiver radio frequency front-end with balun LNA is presented. A hybrid common gate and common source structure balun LNA is adopted, and the capacitive cross-coupling technique is used to reduce the noise contribution of the common source transistor. To obtain low 1/f noise and high linearity, a current mode passive mixer is preferred and realized. A current mode switching scheme can switch between high and low gain modes, and meanwhile it can not only perform good linearity but save power consumption at low gain mode. The front-end chip is manufactured on a 0.13-μm CMOS process and occupies an active chip area of 1.2 mm². It achieves 35 dB conversion gain across 4.9-5.1 GHz, a noise figure of 7.2 dB and an IIP3 of -16.8 dBm, while consuming 28.4 mA from a 1.2 V power supply at high gain mode. Its conversion gain is 13 dB with an IIP3 of 5.2 dBm and consumes 21.5 mA at low gain mode.     

一种集成二进制权精确对数线性可编程增益放大器的卫星导航接收机数字自动增益控制环路

A novel digitally controlled automatic gain control(AGC) loop circuitry for the global navigation satellite system(GNSS) receiver chip is presented. The entire AGC loop contains a programmable gain amplifier(PGA),an AGC circuit and an analog-to-digital converter(ADC), which is implemented in a 0.18 m complementary metal–oxide–semiconductor(CMOS) process and measured. A binary-weighted approach is proposed in the PGA to achieve wide d B-linear gain control with small gain error. With binary-weighted cascaded amplifiers for coarse gain control, and parallel binary-weighted trans-conductance amplifier array for fine gain control, the PGA can provide a 64 dB dynamic range from4 to 60 dB in 1.14 dB gain steps with a less than 0.15 dB gain error. Based on the Gaussian noise statistic characteristic of the GNSS signal, a digital AGC circuit is also proposed with low area and fast settling. The feed-backward AGC loop occupies an area of 0.27 mm2 and settles within less than165 s while consuming an average current of 1.92 mA at 1.8 V.     

CMOS high linearity PA driver with an on-chip transformer for W-CDMA application

A fully integrated high linearity differential power amplifier driver with an on-chip transformer in a standard 0.13-μm CMOS process for W-CDMA application is presented.The transformer not only accomplishes output impedance matching,but also acts as a balun for converting differential signals to single-ended ones.Under a supply voltage of 3.3 V,the measured maximum power is larger than 17 dBm with a peak power efficiency of 21%.The output power at the 1-dB compression point and the power gain are 12.7 dBm and 13.2 dB,respectively. The die size is 0.91×1.12 mm~2.     

A Fully Integrated 60GHz Four Channel CMOS Receiver with 7GHz Ultra-Wide Bandwidth for IEEE 802.11ad Standard

In this paper, a fully integrated CMOS receiver frontend for high-speed short range wireless applications centering at 60GHz millimeter wave （mmW） band is designed and implemented in 90nm CMOS technology. The 60GHz receiver is designed based on the super-heterodyne architecture consisting of a low noise amplifier （LNA） with inter-stage peaking technique, a single- balanced RF mixer, an IF amplifier, and a double-balanced I/Q down-conversion IF mixer. The proposed 60GHz receiver frontend derives from the sliding-IF structure and is designed with 7GHz ultra-wide bandwidth around 60GHz, supporting four 2.16GHz receiving channels from IEEE 802.1lad standard for next generation high speed Wi- Fi applications. Measured results show that the entire receiver achieves a peak gain of 12dB and an input 1-dB compression point of -14.SdBm, with a noise figure of lower than 7dB, while consumes a total DC current of only 60mA from a 1.2V voltage supply.     

12GHz Low Noise Amplifier MMIC

<正> Shown in the front cover is a scanning electron micrograph of a 12GHz two-stagelow noise amplifier MMIC's chip with the size of 3.22×1.49×0.2mm~3, consisting of 2GaAs MESFETs, 6MIM capacitors, 8 airbridges and 9 microstrip lines fabricated byNEDI in 1988. Optimization of the circuits has been done employing our own NAMPprogram, resulting in a noise figure of 3.1dB and an associated gain of 14dB at11.7-12.2GHz.