Enhanced thermal conductivity and dimensional stability of flexible polyimide nanocomposite film by addition of functionalized graphene oxide

Polyimide (PI) nanocomposites with both enhanced thermal conductivity and dimensional stability were achieved by incorporating glycidyl methacrylate‐grafted graphene oxide (g‐GO) in the PI matrix. The PI/g‐GO nanocomposites exhibited linear enhancement in thermal conductivity when the amount of incorporated g‐GO was less than 10 wt%. With the addition of 10 wt% of g‐GO to PI (PI/g‐GO‐10), the thermal conductivity increased to 0.81 W m^?1 K^?1 compared to 0.13 W m^?1 K^?1 for pure PI. Moreover, the PI/g‐GO‐10 composite exhibited a low coefficient of thermal expansion (CTE) of 29 ppm °C^?1. The values of CTE and thermal conductivity continuously decreased and increased, respectively, as the g‐GO content increased to 20 wt%. Combined with excellent thermal stability and high mechanical strength, the highly thermally conducting PI/g‐GO‐10 nanocomposite is a potential substrate material for modern flexible printed circuits requiring efficient heat transfer capability.     

Polydopamine functional reduced graphene oxide for enhanced mechanical and electrical properties of waterborne polyurethane nanocomposites

Waterborne polyurethane/polydopamine (PDA) functional reduced graphene oxide (WPU/PDRGO) nanocomposites were prepared by in situ emulsification method. The presence of a PDA layer and the partial reduction of GO by PDA were confirmed by FTIR, XRD, Raman spectra, and TGA. It was found that the interfacial PDA layers facilitated the dispersion of the PDRGO sheets in the WPU matrix and enhanced mechanical properties of the WPU matrix. The resulting WPU/PDRGO nanocomposite coatings show excellent electrical conductivity (9.9?×?10^?6–1.1?×?10^?4 S cm^?1) corresponding to a PDRGO content of 1–16 wt%. The obtained waterborne polyurethane/graphene nanocomposite dispersions are promising for anticorrosion, antistatic, conductive, and electromagnetic interference shielding coatings.     

Electrically conductive and mechanically tough graphene nanocomposite hydrogels with self‐oscillating performance

Conventional hydrogels are extremely brittle, fragile and poorly conductive, which limits their applications in a variety of aspects. In this study, we fabricated a novel kind of nanocomposite self‐oscillating hydrogel poly(AA‐co‐Fe(phen)₃)/PVA/RGO with high conductivity and good mechanical strength by dispersing reduced graphene oxide (RGO). Due to the synergetic effect of RGO dispersed in the hydrogels or dry gels and Fe metal which is the reduction product of the Fe(phen)₃ moiety by RGO, the hydrogels have a high conductivity of 18.2 S m^?1 with 0.67 wt% RGO content. The dispersed RGO in the hydrogels combined with the network structure by means of hydrogen bonding, π–π stacking and electrostatic interaction and was demonstrated to enhance the mechanical properties of the hydrogels. The elastic modulus achieves 65.2 kPa (1020% of the tensile strength) and 236.4 kPa (with 70% compression), respectively. In addition, the prepared hydrogels exhibit a self‐oscillating behavior in a Belousov–Zhabotinsky solution free of catalyst. These results can be broadly applied in the future in the development of an autonomous on–off switching, flexible/stretchable, graphene‐based soft electronic device. © 2019 Society of Chemical Industry     

A novel polybenzimidazole composite modified by sulfonated graphene oxide for high temperature proton exchange membrane fuel cells in anhydrous atmosphere

A novel functional graphene with high ion exchange capacity (IEC) was prepared by grafting reaction induced by ⁶⁰Co γ‐ray irradiation using graphene oxide. Then, polybenzimidazole/radiation grafting graphene oxide (PBI/RGO) composite membranes were prepared by the solution‐casting method and doped with phosphoric acid (PA) to improve their proton conductivity. The properties of PBI/GO/PA and PBI/RGO/PA membranes including the PA doping level, chemical stability, proton conductivity and mechanical properties were evaluated and compared. The tensile strength of PBI/RGO/PA membranes (ranging from 27.3 to 38.5 MPa) increases at first and then decreases with the increase of the RGO content, and is significantly higher than that of other PA doped PBI‐based membranes. The proton conductivity of PBI/RGO‐3/PA membrane is 28.0 mS cm^?1 at 170 °C without humidity, with an increase of 72.0% compared with that of PBI/PA membrane. These results suggest that PBI/RGO/PA membranes have the potential to be used as high‐temperature proton exchange membranes. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44986.     

Electrical conductivity of silicon carbonitride‐reduced graphene oxide composites

Silicon carbonitride ceramics–reduced graphene oxide (SiCN–rGO) composites are synthesized using polyvinylsilazne (PVSZ) and GO as precursors and N‐dimethylformamide (DMF) as a solvent. We find that the electrical conductivity of SiCN–rGO composites exhibits nonmonotonic changes as a function of GO concentrations, in which the conductivity increases by six orders of magnitude from 7.41E‐09 (Ω/cm)^?1 to 4.35E‐03 (Ω/cm)^?1 after the integration of 0.2 wt% GO, followed by three orders of magnitude drop to 3.34E‐06 (Ω/cm)^?1 when 0.3 wt% GO is integrated. Based on the energy‐dispersive spectroscopy and Raman spectroscopy analysis, we conclude that the conductive behavior of SiCN–rGO composites is controlled by both the concentration and the distribution of “free‐carbon” in the composites.     

Synthesis of cellulose/reduced graphene oxide/polyaniline nanocomposite and its properties

A series of conductive nanocomposites cellulose/reduced graphene oxide/polyaniline (cellulose/RGO/PANi) were synthesized via in situ oxidative polymerization of aniline on cellulose/RGO with different RGO loading to study the effect of RGO on the properties of nanocomposites. The results showed that when RGO is inserted into cellulose/PANi structure, its thermal stability and conductivity are increased. So that adding of only 0.3 wt% RGO into the cellulose/PANi structure, its conductivity is increased from 1.1 × 1 10^?1 to 5.2 × 110^?1 S/cm. Scanning electron microscopy results showed that the PANi nanoparticles are formed a continuous spherical shape over the cellulose/RGO template; this increases the thermal stability of nanocomposite.     

Characterization and performance of dodecyl amine functionalized graphene oxide and dodecyl amine functionalized graphene/high‐density polyethylene nanocomposites: A comparative study

Dodecyl amine (DA) functionalized graphene oxide(DA‐GO) and dodecyl amine functionalized reduced graphene oxide (DA‐RGO) were produced by using amidation reaction and chemical reduction, then two kinds of well dispersed DA‐GO/high‐density polyethylene (HDPE) and DA‐RGO/HDPE nanocomposites were prepared by solution mixing method and hot‐pressing process. Thermogravimetric, X‐ray photoelectron spectroscopy, Fourier transforms infrared spectroscopy, X‐ray diffractions, and Raman spectroscopy analyses showed that DA was successfully grafted onto the graphene oxide surface by uncleophilic substitution and the amidation reaction, which increased the intragallery spacing of graphite oxide, resulting in the uniform dispersion of DA‐GO and DA‐RGO in the nonpolar xylene solvent. Morphological analysis of nanocomposites showed that both DA‐GO and DA‐RGO were homogeneously dispersed in HDPE matrix and formed strong interfacial interaction. Although the crystallinity, dynamic mechanical, gas barrier, and thermal stability properties of HDPE were significantly improved by addition of small amount of DA‐GO or DA‐RGO, the performance comparison of DA‐GO/HDPE and DA‐RGO/HDPE nanocomposites indicated that the reduction of DA‐GO was not necessary because the interfacial adhesion and aspect ratio of graphene sheets had hardly changed after reduction, which resulting in almost the same properties between DA‐GO/HDPE and DA‐RGO/HDPE nanocomposites. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39803.     

Green reduction of graphene oxide by aqueous phytoextracts

The reduction of graphene oxide (GO) by phytochemicals was investigated using aqueous leaf extracts of Colocasia esculenta and Mesua ferrea Linn. and an aqueous peel extract of orange (Citrus sinensis). The prepared GO and phytoextract reduced GO (RGO) were characterized by ultraviolet–visible spectroscopy, Raman spectroscopy and Fourier transform infrared analyses to provide a clear indication of the removal of oxygen-containing groups from the graphene and the formation of RGO. The extent of reduction was determined from elemental analysis. Formation of few layers of graphene was indicated by transmission electron microscopy. The obtained RGO exhibited good specific capacitance (17–21 Fg^?1), high electrical conductivity (3032.6–4006 Sm^?1) and high carbon to oxygen ratio (5.97–7.11).     

Morphological and physical properties of a thermoplastic polyurethane reinforced with functionalized graphene sheet

BACKGROUND: Functionalized graphene sheet (FGS) was recently introduced as a new nano‐sized conductive filler, but little work has yet examined the possibility of using FGS as a nanofiller in the preparation of polymer nanocomposites. In particular, there are currently no published papers that evaluate polyurethane/FGS nanocomposites. The purpose of this study was to prepare a polyurethane/FGS nanocomposite and examine the morphological and physical properties of the material. RESULTS: A cast nanocomposite film was prepared from a mixture of thermoplastic polyurethane (TPU) solution and FGS suspended in methyl ethyl ketone. The FGS dispersed on the nanoscale throughout the TPU matrix and effectively enhanced the conductivity. A nanocomposite containing 2 parts of FGS per 100 parts of TPU had an electrical conductivity of 10^?4 S cm^?1, a 10⁷ times increase over that of pristine TPU. The dynamic mechanical properties showed that the FGS efficiently reinforced the TPU matrix, particularly in the temperature region above the soft segment melt. CONCLUSION: Our results show that FGS has a high affinity for TPU, and it could therefore be used effectively in the preparation of TPU/FGS nanocomposites without any further chemical surface treatment. This indicates that FGS is an effective and convenient new material that could be used for the modification of polyurethane. It could also be used in place of other nano‐sized conductive fillers, such as carbon nanotubes. Copyright © 2009 Society of Chemical Industry     

Highly thermal conductive composites with polyamide-6 covalently-grafted graphene by an in situ polymerization and thermal reduction process

The thermal conductive polyamide-6/graphene (PG) composite is synthesized by in situ ring-opening polymerization reaction using ε-caprolactam as the monomer, 6-aminocaproic acid as the initiator and reduced graphene oxide (RGO) as the thermal conductive filler. The generated polyamide-6 (PA6) chains are covalently grafted onto graphene oxide (GO) sheets through the “grafting to” strategy with the simultaneous thermal reduction reaction from GO to RGO. The homogeneous dispersion of RGO sheets in PG composite favors the formation of the consecutive thermal conductive paths or networks at a relatively low GO sheets loading, which improves the thermal conductivity (λ) from 0.196 W m⁻¹ K⁻¹ of neat PA6 to 0.416 W m⁻¹ K⁻¹ of PG composite with only 10 wt% GO sheets loading.     

Graphene network enabled high speed electrical actuation of shape memory nanocomposite based on poly(vinyl acetate)

Here strong electroactive shape memory nanocomposites were prepared by incorporating graphene nanoplatelets into poly(vinyl acetate) (PVAc ) through the simple solvent mixing method. TEM and XRD revealed that well exfoliated graphene nanoplatelets formed a continuous network throughout the matrix with a large amount of interconnectedness. Dynamic mechanical analysis showed that the inclusion of graphene significantly improves both glassy and rubbery moduli of the matrix. Furthermore, the prepared nanocomposites demonstrated a marked electrical conductivity up to 24.7 S m^?1 and thereby surprisingly rapid electrical actuation behaviour exhibiting a 100% recovery ratio in 2.5 s. Moreover, PVAc and its nanocomposites displayed scratch self‐healing capability. This work demonstrates that the PVAc /graphene nanocomposites with high modulus and excellent electroactive shape memory performance can be a promising material in many applications such as sensors and fast deployable and actuating devices. © 2016 Society of Chemical Industry     

Highly electrically and thermally conductive silicon carbide-graphene composites with yttria and scandia additives

Dense silicon carbide/graphene nanoplatelets (GNPs) and silicon carbide/graphene oxide (GO) composites with 1 vol.% equimolar Y₂O₃–Sc₂O₃ sintering additives were sintered at 2000 °C in nitrogen atmosphere by rapid hot-pressing technique. The sintered composites were further annealed in gas pressure sintering (GPS) furnace at 1800 °C for 6 h in overpressure of nitrogen (3 MPa). The effects of types and amount of graphene, orientation of graphene sheets, as well as the influence of annealing on microstructure and functional properties of prepared composites were investigated. SiC-graphene composite materials exhibit anisotropic electrical as well as thermal conductivity due to the alignment of graphene platelets as a consequence of applied high uniaxial pressure (50 MPa) during sintering. The electrical conductivity of annealed sample with 10 wt.% of GNPs oriented parallel to the measuring direction increased significantly up to 118 S·cm⁻¹. Similarly, the thermal conductivity of composites was very sensitive to the orientation of GNPs. In direction perpendicular to the GNPs the thermal conductivity decreased with increasing amount of graphene from 180 W·m⁻¹ K⁻¹ to 70 W·m⁻¹ K⁻¹, mainly due to the scattering of phonons on the graphene – SiC interface. In parallel direction to GNPs the thermal conductivity varied from 130 W·m⁻¹ K⁻¹ up to 238 W·m⁻¹ K⁻¹ for composites with 1 wt.% of GO and 5 wt.% of GNPs after annealing. In this case both the microstructure and composition of SiC matrix and the good thermal conductivity of GNPs improved the thermal conductivity of composites.     

Synthesis of polypyrrole-reduced graphene oxide composites by in-situ photopolymerization and its application as a supercapacitor electrode

A highly conductive polypyrrole (PPy)-reduced graphene oxide (RGO) composite with an electrical conductivity of 610 S m⁻¹ was successfully synthesized by the in-situ photopolymerization of pyrrole in a graphene oxide suspension. Graphene oxide (GO) played the role of an electron acceptor and was reduced as it accepted electrons. The reduction of GO was confirmed by the increase in the C/O ratio of RGO with the UV irradiation time as well as the high electrical conductivity of PPy-RGO composite. Through the thermogravimetric analysis, it has been found that the PPy-RGO composite exhibited high thermal stability compared to the GO and PPy. This material was used as an electrode in a supercapacitor cell and showed excellent performance for electrical energy storage. The composite exhibited a specific capacitance of 376 F g⁻¹ at a scan rate of 25 mV s⁻¹.     

One-step electrosynthesis of MnO2/rGO nanocomposite and its enhanced electrochemical performance

We present a facile one-step electrochemical approach to generate MnO₂/rGO nanocomposite from a mixture of Mn₃O₄ and graphene oxide (GO). The electrochemical conversion of Mn₃O₄ into MnO₂ through potential cycling is expedited in the presence of GO while the GO is reduced into reduced graphene oxide (rGO). The MnO₂ nanoparticles are evenly distributed on the rGO nanosheets and act as the spacer to prevent rGO nanosheets from restacking. This unique structure provides high electroactive surface area (1173?m² g^?1) that improves ions diffusion within the MnO₂/rGO structure. As a result, the MnO₂/rGO nanocomposite exhibits high specific capacitance of 473?F?g^?1 at 0.25?A?g^?1, which is remarkably higher (3 times) than the Mn₃O₄/GO prior conversion. In addition, the electrosynthesized nanocomposite shows higher conductivity and excellent potential cycling stability of 95% at 2000 cycles.     

Comparative study of gamma and ion beam irradiation of polymeric nanocomposite on electrical conductivity

Poly(vinyl alcohol) (PVA) was used to prepare nanocomposites of multi‐wall carbon nanotubes (MWCNT) and functionalized carbon nanotubes (MWCNT‐NH₂) in existence of 2‐carboxyethyl acrylate oligomers (CEA). Radiation‐induced crosslinking of the prepared matrix was carried out via gamma and ion beam irradiation. A comparative study of gamma and ion beam irradiation effect on the electrical conductivity of nanocomposite was conducted. The gelation of the gamma irradiated matrix outperforms the ion beam irradiated matrix. The order of gelation is PVA > (PVA/CEA) > (PVA/CEA)‐MWCNT > (PVA/CEA)‐MWCNT‐NH₂. There is a significant reduction in the swelling of the nanocomposite. The formation of nanocomposites was confirmed by scanning electron microscopy, energy‐dispersive X‐ray (EDX) and FTIR examinations. The direct current electrical properties of PVA/nanocomposites are examined at room temperature by applying electric voltage from 1 to 20 V. The results revealed that the electrical conductivity is increased by adding the carbon nanotubes and irradiation by gamma and ion beam. At an applied electric voltage 20 V, in the electrical conductivity of the unirradiated PVA was from 9.20 × 10^?8 S cm^?1. After adding MWCNT an increase up to 4.70 × 10^?5 S cm^?1 was observed. While after ion beam irradiation, a further increase up to 9.30 × 10^?5 S cm^?1 was noticed. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46146.     

Enhanced conductivity of bacterial cellulose films reinforced with NH4I-doped graphene oxide

ABSTRACT

Bacterial cellulose (BC) films reinforced with reduced graphene oxide (RGO) platelets were investigated to assess their potential application as solid polymeric electrolytes. BC-RGO composites were further doped with NH₄I at different concentrations to evaluate the effect of NH₄I doping on the conductivity. Scanning electron microscopy images confirmed that GO addition did not alter BC coherent three-dimensional morphology. Electrochemical impedance spectroscopy studies revealed that the ionic conductivity increased with the ammonium iodide salt concentration. The highest conductivity found was 1.32 × 10^?4 S/cm for the samples doped with 5% NH₄I, suggesting that BC-RGO can be a promising candidate for electrochemical applications.     

Li‐ion conductivity in PEO‐graphene oxide nanocomposite polymer electrolytes: A study on effect of the counter anion

Graphene oxide (GO) has been prepared by modified Hummer's method for their incorporation as nanofiller in designing nanocomposite polymer electrolytes (NCPEs). Prior to use the GO nanofillers has been characterized by TEM, FTIR, and Raman studies to elucidate their nanostructure, functionality, and purity. The various poly(ethylene oxide) (PEO)‐based NCPEs has been prepared by incorporating GO nanofillers in presence of three different lithium salts, viz., CF₃SO₃Li, LiTFSI, and LiNO₃ as the source of Li‐ions and then casted into free standing polymeric films. The change in PEO crystallinity has been studied considering their full width half maximum values of respective diffraction peaks in the XRD spectra. The Li‐ion conductivity of various NCPEs has been studied from impedance spectroscopy. All the NCPE films show optimum value of Li‐ion conductivity with 0.3% GO nanofiller content irrespective of the source of Li‐ions used. But, variation of the Li‐ion conductivity values is occurred for all the three studied lithium salts. Both LiTFSI and LiNO₃ salts display Li‐ion conductivity in the order of 10^?4 S cm^?1 whereas CF₃SO₃Li in the order of 10^?6 S cm^?1, all in presence of 0.3% GO nanofillers. The change in conductivity values of the NCPEs has been explained by correlating with Argand plots and also with change in PEO crystallinity, which occurs due to various relaxation processes. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46336.     

Synthesis and electrochemical properties of graphene oxide/nanosulfur/polypyrrole ternary nanocomposite hydrogel for supercapacitors

A method for synthesizing Graphene oxide (GO)/nano‐sulfur/polypyrrole (PPy) ternary nanocomposite hydrogel is depicted. The higher surface area of GO, PPy porous structure and their excellent conductivity are utilized, and the GO hydrogel can be made easily. The products are characterized by field‐emission scanning electron microscopy (FESEM), X‐ray diffraction (XRD), Fourier transform infrared (FTIR) spectra, and electrochemical workstation. The results demonstrated that GO/nano‐S/PPy ternary nanocomposite hydrogel is successfully synthesized. The electrochemical properties are investigated by cyclic voltammetry, galvanostatic charge/discharge measurements, and cycling life in a three‐electrode system in 1M Li₂SO₄ electrolyte solution. The GO/nano‐S/PPy ternary nanocomposite hydrogel exhibit a high specific capacitance of 892.5 F g^?1 at scan rates of 5 mV s^?1 and the capacitance retain about 81.2% (594.8 F g^?1) of initial capacitance (732.5 F g^?1) after 500 cycles at a current density of 1 A g^?1. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40814.     

The synthesis and characteristics of sodium alginate/graphene oxide composite films crosslinked with multivalent cations

Association of a method of the incorporation of graphene oxide (GO) into sodium alginate (Na‐alg) polymer matrix with a method of the use multivalent cations crosslinker was put forward to synthesize novel Na‐alg/GO nanocomposite films. The structures, morphologies, and the properties of Na‐alg/GO films were characterized by Fourier transform infrared (FTIR) spectroscopy, X‐ray diffraction (XRD), field‐emission scanning electron microscopy (FE‐SEM), thermogravimetric analysis (TGA), and tensile tests. The results revealed that the interlayer distance of GO sheets increased from 0.83 nm to 1.08 nm after assembling with Na‐alg, and Na‐alg inserted into GO layers crosslinking with multivalent cations increased the interlayer distance further. Ionic crosslinking significantly enhanced thermal and mechanical properties of Na‐alg/GO nanocomposite films. In particular, Fe³⁺ led to Na‐alg/GO nanocomposite films of significantly higher tensile strength and modulus than Ca²⁺ and Ba²⁺. The excellent thermal and mechanical properties of these novel Na‐alg/GO nanocomposite films may open up applications for Na‐alg films. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43616.     

Preparation and physical properties of functionalized graphene/waterborne polyurethane UV‐curing composites by click chemistry

Functionalized graphene nanoplatelets (f‐GNS) were modified with (3‐mercaptopropyl)trimethoxysilane (MPTMS) to enhance their compatibility with the polyurethane coating matrix. The results of Fourier transform infrared spectroscopy, AFM, Raman and XRD showed that the MPTMS was successfully attached onto the surface of the graphene nanoplatelets. Functionalized graphene/waterborne polyurethane acrylate (f‐GNS/WPUA) nanocomposites were fabricated by UV‐curing technology. The SEM and TEM images indicated that f‐GNS could be well dispersed in the polymer matrix and improved the interfacial adhesion. With the incorporation of 1 wt% f‐GNS, the thermal decomposition temperature of the composites was increased by 25 °C. Meanwhile, the conductivity, hydrophobicity and tensile strength were increased. When the load was further increased, the performance of the composites showed varying degrees of reduction. However, the dielectric loss tangent (tan δ) could be maintained at 0.08 or less and the electromagnetic shielding factor of the composites reached from 5 to 36 dB, showing a good electromagnetic shielding effect at a high content (2.5 wt% f‐GNS). It was considered that f‐GNS could disperse in the waterborne polyurethane well and crosslink with the polyurethane. © 2016 Society of Chemical Industry