Poly(acrylic acid)/poly(acrylamide) hydrogel adsorbent for removing methylene blue

Cationic dye can cause severe damage to the environment due to their refractory degradation, complex composition and strong stability. Hydrogels as adsorbents have been widely used to treatment the wastewater with dyestuff for their low prices, simple operations, and high efficiency. This work uses poly(acrylic acid) (PAA)/poly(acrylamide)(PAM)/calcium hydroxide nanoparticles (CHN) polymeric hydrogel absorbent to eliminate methylene blue (MB) dye. First, PAM/PAA/CHN hydrogel is produced through copolymerization of acrylic acid monomer and acrylamide monomer using inorganic CHN as cross-linker. And then, the adsorption performance of such PAM/PAA/CHN hydrogel adsorbent for adsorbing MB dye is explored at different conditions including pH, contacting time, adsorbent dosage, initial concentration of MB, and temperature. A maximum adsorption capability for adsorbing MB reaches 1,056 mg/g. Furthermore, the pseudo-first-order mode and Langmuir isotherm model can well describe adsorption behavior of MB dye onto such PAA/PAM/CHN hydrogel adsorbent. Thereby, as-prepared PAA/PAM/CHN hydrogel could be a potential adsorbent for eliminating organic dyes from wastewater.     

Synthesis of polyacrylate/poly(ethylene glycol) hydrogel and its absorption properties for heavy metal ions and dye

A novel polyacrylate/poly(ethylene glycol) (PAA/PEG) hydrogel was synthesized by a simple two‐step aqueous prepolymerization method. The deswelling properties were investigated in the case of changing the neutralization degrees of PAA, the pHs and the concentration of multivalent salt solutions. Methyl orange (MO) dye can be adsorbed and released using the swelling–deswelling property of the PAA/PEG hydrogel. The PAA/PEG hydrogel can adsorb MO of 29 mg/g at equilibrium and release about 80% in 30 min. Based on the deswelling property, the dyes in wastewater can be reclaimed and reused. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

Poly(acrylamide/laponite) nanocomposite hydrogels: Swelling and cationic dye adsorption properties

Super adsorbent polyacrylamide (PAAm)/nanoclay (laponite, Lap) hydrogels were prepared by in situ free radical polymerization of AAm in an aqueous solution with clay as a crosslinker. The swelling properties and water‐soluble cationic dye adsorption behaviors of the PAAm/laponite (PAAm/Lap) nanocomposite (NC) hydrogels were investigated. The parameters of swelling and diffusion of water in dye solutions were evaluated for the PAAm/Lap NC hydrogels. The adsorption behavior of the monovalent cationic dyes such as Basic Blue 12 (BB 12), Basic Blue 9 (BB 9), and Basic Violet 1 (BV 1), were studied on the NC hydrogels. The effects of the clay content of the hydrogel on its cationic dye uptake behavior were studied. The adsorption studies indicated that the rates of dye uptake by the NC hydrogels increased in the following order: BB 9 > BB 12 > BV 1. This order is similar to the swelling results of the PAAm/Lap NC hydrogel in the dye solutions. The equilibrium uptakes of the different dyes by the PAAm/Lap NC hydrogel were nearly the same. In the dye absorption studies, S‐type adsorption in the Giles classification system was found for the BB 12 and BV 1 dyes, whereas L ‐type was observed for the BB 9 dye. After the heat treatment of PAAm/Lap, the rate of dye uptake and equilibrium dye uptake were increased. The NC hydrogels may be considered as a good candidate for environmental applications to retain more water and to remove dyes. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Use of superswelling acrylamide/maleic acid hydrogels for monovalent cationic dye adsorption

Acrylamide/maleic acid (AAm/MA) superswelling hydrogels prepared by irradiation with γ radiation were used in experiments on swelling, diffusion, and adsorption of some water‐soluble monovalent cationic dyes such as basic red 5 (BR‐5), basic violet 3 (BV‐3), and brilliant cresyl blue (BCB). The AAm/MA hydrogel containing 60 mg MA and irradiated at 5.20 kGy was used for swelling and diffusion studies in water and aqueous solutions of the monovalent cationic dyes. For this superswelling hydrogel the swelling studies indicated that swelling increased in the following order: BR‐5 > water > BV‐3 ≥ BCB. The diffusion of water and the dyes within the hydrogels was found to have a non‐Fickian character. The uptake of the cationic dyes to the AAm/MA superswelling hydrogels was studied by the batch adsorption technique at 25°C. The uptake of dyes within the hydrogel increased in the following order: BR‐5 > BV‐3 > BCB. In the experiments of the adsorption equilibrium, S‐type adsorption in Giles' classification system was found. The binding ratio of the hydrogel/dye systems was gradually increased with the increase of the MA content in the AAm/MA hydrogel and the irradiation dose. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 79: 1809–1815, 2001     

Swelling and dye adsorption study of novel superswelling [Acrylamide/N-vinylpyrrolidone/3(2-hydroxyethyl carbamoyl) acrylic acid] hydrogels

Summary Super swelling acrylamide (Am)/N-vinylpyrrolidone (NVP)/3-(2-hydroxyethyl carbamoyl) acrylic acid (HECA) hydrogels were prepared by free radical polymerization of quaternary mixtures of Am, NVP, HECA and water. The hydrogels were used in experiments on swelling, diffusion and adsorption of some water-soluble monovalent cationic dyes such as Crystal Violet (CV), Malachite Green (MG) and Methylene Blue (MB). In the experiment of the adsorption of dyes from their aqueous solutions type-S adsorption isotherm were found. The diffusion of water within the hydrogel was found to have non Fickian character. The uptake of dyes within the hydrogel increased in the following order: MG > MB > CV. The binding ratio of the hydrogel/dye systems was gradually increased with the increase of HECA content in the AAm/NVP/HECA hydrogel.     

Adsorption Behavior of Methylene Blue from Aqueous Solution by the Hydrogel Composites Based on Attapulgite

A series of carboxymethyl cellulose-g-poly (acrylic acid)/attapulgite hydrogel composites were synthesized for the removal of cationic dye methylene blue. Various factors affecting the uptake behavior were investigated. Adsorption rate of the hydrogel was quite fast, and adsorption equilibrium could be reached within 30 min. Adsorption kinetics well followed the pseudo-second-order equation for all systems. The Langmuir isotherm was found to best represent the data for the dye uptake. Even when 20 wt% attapulgite was introduced into the hydrogel, the corresponding maximum adsorption capacity reached 1979.48 mg/g at 30°C. The as-prepared adsorbents exhibited excellent affinity for the dye, and can be applied to treat wastewater containing basic dyes.     

Adsorption behavior of cationic dyes on citric acid esterifying wheat straw: kinetic and thermodynamic profile

The kinetic and thermodynamic behaviors of cationic dye adsorption onto citric acid esterifying wheat straw (EWS) from aqueous solution were investigated. Two cationic dyes, methylene blue (MB) and crystal violet (CV) were selected as adsorbates. The kinetic and thermodynamic parameters of dye adsorption were examined with a batch system by changing various experimental factors (e.g. initial pH, EWS dosage, dye concentration, contact time, temperature). The MB and CV removal ratios came up to the maximum value beyond pH 4. The 2.0 g/L or up of EWS could almost completely remove MB and CV from 250 mg/L of dye solution. The adsorption percentages of MB and CV kept above 95% over a range from 50 to 350 mg/L of dye concentration when 2.0 g/L of EWS was used. The isothermal data followed the Langmuir model. The adsorption processes could be described by the pseudosecond-order kinetic model. The dual linear plots of intraparticle diffusion indicated that two intraparticle diffusion steps occurred in the dye adsorption processes. The thermodynamic study indicated that the adsorptions of dyes were spontaneous and endothermic. High temperatures favored the adsorption processes.     

Nanocomposite hydrogels for selective removal of cationic dyes from aqueous solutions

Removal of organic dyes from waste water has received a significant attention in recent years. In this work, a set of nanocomposite hydrogels (NHs) were prepared and their capacity to absorb crystal violet (CV), a cationic dye, and acid yellow‐23 (AY), an anionic dye, from aqueous solutions was determined. NHs were prepared by in situ formation of Fe₃O₄ magnetic nanoparticles (MNPs) inside poly(acrylamide‐co‐4‐styrene sulfonic acid sodium salt) (P[AAm‐co‐SSA]) hydrogel matrices. The dye absorption capacity of the magnetic NHs (MNHs) was compared with simple hydrogels (hydrogels or SHs) without the MNPs The prepared hydrogels were characterized by FTIR, XRD, thermogravimetric analysis, high resolution TEM, field emission SEM, and vibrating sample magnetometer measurement. From HRTEM, it was confirmed that the prepared MNPs in hydrogel matrices were in the size range of about 8 to 10 nm. The MNHs showed greater swelling behavior as well as greater removal efficiency of cationic dye from aqueous solutions in comparison to the SHs. With increase of SSA mole percentage, dye removal efficiency was also increased for both types of hydrogels. The present study indicates that the hydrogels containing MNPs can be potentially used as an efficient absorbent material for removal of cationic dyes from waste water. POLYM. ENG. SCI., 56:776–785, 2016. © 2016 Society of Plastics Engineers     

Adsorption behavior of crystal violet from aqueous solutions with chitosan–graphite oxide modified polyurethane as an adsorbent

A series of chitosan (Ch)–graphite oxide (GO)‐modified polyurethane foam (PUF) materials as adsorbents were synthesized by a foaming technique. The adsorbent was characterized through IR spectroscopy, scanning electron microscopy, and thermogravimetric analysis (TGA). Batch adsorption experiments of the cationic dye crystal violet (CV) were carried out as a function of the Ch–GO content (1.0–8.0 wt %), solution pH (2–10), dye concentration (100–300 mg/L), adsorbent dosage (10–60 mg/mL), and temperature (20–45°C). At a lower pH value, the surface of Ch–GO/PUF acquired positive charge by absorbing H⁺ ions; this resulted in a decreasing adsorption of the cationic CV dye because of electrostatic repulsion. As the pH of the aqueous system increased, the numbers of negatively charged sites increased by absorbing OH⁻ ions, and a significantly high electrostatic attraction existed between the negatively charged surface of Ch–GO/PUF and the cationic dye (CV) molecules. This led to maximum dye adsorption. The kinetics, thermodynamics, and equilibrium of CV adsorption onto Ch–GO/PUF were investigated. The equilibrium data for CV adsorption fit the Langmuir equation, with a maximum adsorption capacity of 64.935 mg/g. The adsorption kinetics process followed the pseudo‐second‐order kinetics model. Thermodynamic parameters analysis revealed that the adsorption of CV from an aqueous solution by a Ch–GO modified PUF material was a spontaneous and endothermic process. We concluded that Ch–GO/PUF is a promising adsorbent for the removal of CV from aqueous solutions. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41828.     

壳聚糖/聚丙烯酸水凝胶的制备及对Cu2 和Cd2 的吸附性能

以丙烯酸(AA)和壳聚糖(CS)为原料,N,N''-亚甲基双丙烯酰胺(MBA)为交联剂,利用辉光放电电解等离子(GDEP)技术在水溶液中一步引发制备壳聚糖/聚丙烯酸(CS/PAA)水凝胶。采用FT-IR、XRD和SEM对水凝胶的结构和形貌进行表征,考察了溶液pH、吸附时间和初始浓度对Cu2 和Cd2 吸附的影响,探讨了水凝胶的重复利用性。结果表明,丙烯酸成功接枝到壳聚糖链上,水凝胶呈现多孔的三维网络结构,CS/PAA对Cu2 和Cd2 的吸附符合Langmuir 吸附等温式和准二级动力学模型,由Langmuir 模型得到的最大理论吸附量为161.8和327.9 mg/g,该水凝胶在EDTA-4Na溶液中具有良好的再生和重复利用性。     

Studies on auramine dye adsorption on psidium guava leaves

Removal of auramine dye from aqueous waste solutions was investigated by using very cheap and biosorbent, withered guava tree leaves and activated carbon. Guava leaves are readily available in the western and northern parts of India throughout the year, and hence form a cost effective alternative for removal of dyes from waste waters. The optimum contact time was found to be 120 min. in a pH range of 8–9 for 92–94% removal of the dye from aqueous solutions containing 150 mg/L of auramine dye using 2 g of the adsorbent. The effect of pH, dye concentration, sorbent dosage, temperature and contact time on the dye removal efficiency has been studied. Experimental results were found to fit both Freundlich and Langmuir models. Since the dye contains a cationic species, the removal efficiency was highest in a pH range of 8–9. Continuous adsorption studies in a packed column showed 100% removal efficiency for a flow rate of 10 ml·min⁻¹. When compared with the activated carbon, it was also found that adsorbent derived from guava leaves is more efficient in removal of dye.     

Removal of methylene blue from aqueous solution by sorption on lignocellulose-g-poly(acrylic acid)/montmorillonite three-dimensional cross-linked polymeric network hydrogels

Batch lignocellulose-g-poly(acrylic acid)/montmorillonite (LNC-g-PAA/MMT) hydrogel nanocomposites were applied as adsorbents. The nanocomposites were characterized by FTIR, XRD, SEM, and TEM. The results showed that montmorillonite (MMT) could react with the monomers and change the structure of polymeric network of the traditional superabsorbent materials, an exfoliated structure was formed in the nanocomposites. The effect of process parameters such as MMT content (wt%), contact time (t), initial concentration of dye solution (C ₀), adsorption temperature (T), and pH value (pH) of the dye solution for the removal of methylene blue (MB) from aqueous solution were also studied. The results showed that the adsorption capacity for MB increased with increasing contact time, initial dye concentration, and pH value, but decreased with increasing MMT content and temperature. The adsorption kinetics were better described by the pseudo-second-order equation, and their adsorption isotherms were better fitted for the langmuir equation. By introducing 20 wt% MMT into LNC-g-PAA polymeric network, the obtaining hydrogel composite showed the high adsorption capacity 1994.38 mg/g and economic advantage for MB. The desorption studies revealed that the composite provided the potential for regeneration and reuse after MB dye adsorption, which implied that the composite could be regarded as a potential adsorbent for cationic dye MB removal in a wastewater treatment process.     

Removal of Cationic Dyes from Aqueous Solution by Hydrophobically Modified Poly(acrylic Acid) Hydrogels

Hydrophobically modified poly(acrylic acid) hydrogels were synthesized using acrylic acid (AA), methyl methacrylate (MMA), ethyl methacrylate (EMA) and butyl methacrylate (BMA) as copolymer monomers. These hydrogels were carried out for removal cationic dyes from aqueous solution. It was found that the adsorption of cationic dye depended on the length of the side chain, hydrophobic monomer (MMA, EMA and BMA) content and pH of the solution. Increasing the hydrophobic monomer content led to an increase in the adsorption of cationic dyes on the hydrogels. The adsorption kinetics and isotherms of hydrogels were in good agreement with pseudo–second-order equation and the Langmuir equation, respectively. The cationic dyes adsorption of hydrogels involved a mechanism that combined swelling and electrostatic and hydrophobic interaction.     

A new electrode reactor with in-built recirculation mode for the enhancement of methylene blue dye removal from the aqueous solution: Comparison of adsorption,electrolysis and combined effect

The removal of basic dye such as methylene blue (MB) dye from the synthetic wastewater was experimentally investigated using an electrolytic cell (EC), adsorption and the combined effect of EC and adsorption technology called a three-phase three-dimensional electrode reactor (TPTDER). The performance of the each technology was checked on the basis of the efficiency of the systems. The experimental results are expressed in terms of the removal efficiency of the dye molecules. The results show that the TPTDER could efficiently remove the dye molecules from the aqueous solutions when compared with the EC and adsorption process. The removal efficiency reached as high as about 99% for an initial MB dye concentration in the range of 100–1,000 mg/L by TPTDER for 10 min at 12 V cell voltage and at specific airflow conditions. It was also observed that the removal of dye molecules depends upon the initial solution pH, applied cell voltage, contact time, and initial dye concentration. The recyclability of the particle electrodes in the TPTDER process was also checked. These findings suggest that TPTDER is a promising technology for the removal of dyes from the aqueous solution, and can be applied to the removal of dyes from the industrial effluents.     

Adsorption of cationic dyes on poly(acrylic acid‐co‐sodium acrylate‐co‐acrylamide) superabsorbents

Inverse suspension polymerization was carried out to synthesize poly(acrylic acid‐co‐sodium acrylate‐co‐acrylamide) superabsorbent polymers (SAPs) crosslinked with ethylene glycol dimethacrylate (EGDMA). The equilibrium swelling capacities of the SAPs, determined by swelling them in DI water, were found to vary with the acrylamide (AM) content. The SAPs were used to adsorb four cationic dyes (Acriflavine, Auramine‐O, Azure‐I and Pyronin‐Y). The effect of AM content in the SAPs on the adsorption of the cationic dyes was investigated. Different initial concentrations of Azure‐I were used with the same amount of the SAP to explore the effect of initial dye concentration on the adsorption. The effect of the adsorbent amount was investigated by taking different amounts of SAP with a fixed initial concentration of Acriflavine. The kinetics of the dye adsorption was modeled by a first order model and the equilibrium amount of the dye adsorbed, adsorption rate coefficients, removal efficiency and partition coefficients were determined. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Poly(methacrylic acid)‐modified chitosan for enhancement adsorption of water‐soluble cationic dyes

The preparation of poly(methacrylic acid)‐modified chitosan microspheres and its application for the removal of cationic dyes, methylene blue (MB) and malachite green (MG), in aqueous solution in a batch system were described. The modified chitosan was characterized using SEM, FTIR, and XPS analyses. The effects of the pH of the solution, contact time, and initial dye concentration were studied. The adsorption capacities of the microspheres for the two cationic dyes increased significantly after the modification because a large number of carboxyl groups were introduced. The equilibrium process was better described by the Langmuir than the Freundlich isotherm. According to the Langmuir equation, the maximum adsorption capacities were 1000.0 and 523.6 mg g^?1 for MB and MG, respectively. Kinetic studies showed better correlation coefficients for a pseudo‐second‐order kinetic model, confirming that the sorption rate was controlled by a chemisorption process. POLYM. ENG. SCI., 2009. © 2008 Society of Plastics Engineers     

坡缕石/聚乙二醇/丙烯酸水凝胶的表征及其对阳离子染料的吸附性能

采用红外光谱、X射线衍射和扫描电镜对辉光放电电解等离子体引发制备的坡缕石/聚乙二醇/丙烯酸(PGS/PEG/AA)水凝胶的结构和形貌进行了表征.研究了其对阳离子型染料亚甲基蓝、结晶紫、孔雀石绿和罗丹明B的吸附行为,考察了pH值、吸附时间对吸附性能的影响,同时探讨了可能的吸附机理.结果表明,PGS、PEG和AA发生接枝共聚形成水凝胶,组分间相容性好,表面呈现褶皱和深浅不均匀的孔洞;吸附的最佳pH值为6.2左右,吸附时间为3h,吸附动力学符合准二级模型,阳离子染料在PGS/PEG/AA上的吸附是由离子交换、氢键、范德华力等共同作用的物理化学过程.     

Dye adsorption characteristics of alginate/polyaspartate hydrogels

This study examined the removal of some basic dyes, such as Methylene Blue, Malachite Green and Methyl Orange, using alginate or alginate/polyaspartate composite gel beads. The adsorption of dyes from aqueous solutions at 25 °C was examined using a batch sorption technique. The effects of CaCl₂ and the dye concentration on the adsorption were examined. Type-S adsorption isotherms were obtained, which is characteristic of a weak solute–solid interaction. The ionic interaction between the dye molecule and gel matrix appears to be responsible for the efficient adsorption of cationic dyes in this system. These results suggest that an alginate/polyaspartate gel can be used as an effective sorbent for water pollutants such as dyes, and the immobilization of these organic contaminants in the hydrogels from wastewater can solve one of the most important environmental problems in the related industry.     

Equilibrium and kinetics study of methyl violet adsorption by pineapple leaf fibers-cl-poly(acrylic acid-co-2-dimethyl amino ethyl acrylate) hydrogel

The pine apple leaf fiber-cl-poly(acrylic acid-co-2-dimethyl amino ethyl acrylate) hydrogel is prepared by crosslinked graft copolymerization of acrylic acid and 2-(dimethyl amino) ethyl acrylate onto the pine apple leaf fibers to be used as an adsorbent for the remove dye from aqueous solutions. Several characterization techniques like Fourier transform infrared spectroscopy field emission scanning electron microscopy-Energy-dispersive X-ray spectroscopy and X-ray diffraction analysis. The synthesized hydrogel shows strong water swelling characteristics (780.93%) and also exhibits faster deswelling property. The methyl violet (MV) adsorption data are fitted well with the Freundlich isotherm model with maximum monolayer adsorption capacities 625 mg/g for MV. The equilibrium kinetics follow pseudo second order model together with intra particle diffusion, one step process. Thermodynamic parameters show that the MV adsorption by the hydrogel is spontaneous and endothermic in nature. The overall removal efficiency is found to be 98.23% under optimum condition.