酸性溶液中PTW增强PTFE复合材料的耐蚀性和摩擦磨损性能

分别研究了不同含量钛酸钾晶须(PTW)、碳纤(CF)填充聚四氟乙烯(PTFE)复合材料在硫酸溶液中和干摩擦条件下摩擦学性能以及酸中的耐蚀性能,借助SEM等分析探讨了相关机理。结果表明,酸中纯PTFE耐磨性较干摩擦条件下提高了2个数量级,摩擦系数也只有干摩擦的15.3%。与CF/PTFE相比,PTW/PTFE复合材料在酸中显示更好的耐蚀和耐磨性能。PTW可以进一步提高PTFE酸中耐磨性能、降低摩擦系数。含15%（质量）PTW时复合材料具有最低的磨损率,此时比纯PTFE酸中耐磨性提高13.8倍,是相同含量CF/PTFE耐磨性的3.2倍。由于酸溶液的冷却和润滑作用,复合材料的摩擦系数与干条件相比明显降低。然而,酸溶液阻止了转移膜的形成。不管是干摩擦还是在酸性溶液中,当填料含量超过15%（质量）时,犁削和磨粒磨损是PTFE复合材料的主要磨损机理。     

Durable polytetrafluoroethylene composites in harsh environments: Tribology and corrosion investigation

The tribological properties and mass loss of polytetrafluoroethylene (PTFE) composites filled with carbon fiber (CF) or potassium titanate whisker (PTW) after the immersion in 30% sulfuric acid solution for 5 or 15 days were studied under different temperatures (25, 50, and 75°C). Results show that PTW/PTFE composites exhibit better anticorrosive and antiwear properties than those of CF/PTFE composites. Acid immersion has no obvious effect on the wear rate of the PTW/PTFE composite. The wear rate of CF/PTFE immersed for 15 days is thrice as much that of untreated composites and 3.6 times as much that of PTW/PTFE composites. Results also indicate that the wear rate of PTFE composites increases with the increasing corrosive mass loss rate and is more dependent on the corrosive mass loss rate rather than the friction coefficient. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Enhanced tribological performance of hybrid polytetrafluoroethylene/Kevlar fabric composite filled with milled pitch‐based carbon fibers

As self‐lubricating bearing liner materials, tribological properties of milled pitch‐based carbon fibers (CFs) modified polytetrafluoroethylene (PTFE)/Kevlar fabric composites were investigated, and the microscopic morphology of worn surface was studied. The results show that the appropriate incorporation of CFs can obviously reduce the wear rate of the fabric composite with almost unchanging friction coefficient. The wear rates of 5 wt % CF‐filled PTFE/Kevlar fabric composites are decreased by 30% and 48% for two kinds of composites made with fibers from different producers compared with unfilled fabric composites. Scanning electron microscopy observations show that the appropriate incorporation of CFs obviously improves the interfacial bonding and reduces pull‐out and fracture of Kevlar fiber. Meanwhile, the introduction of CFs at proper fraction is helpful to form smooth and continuous transfer film on the surface of metal counterpart. The improving mechanism of the CF is attributed to increasing mechanical strength, thermal conductivity and self‐lubricating effects. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46269.     

混杂填料增强聚四氟乙烯复合材料的摩擦学性能研究

采用MM-200型摩擦磨损试验机对纳米SiC、MoS2和石墨填充聚四氟乙烯(PTFE)复合材料在干摩擦条件下与45#钢对摩时的摩擦磨损性能进行了研究,探讨了MoS2、石墨及纳米SiC的协同效应。认为纳米SiC的加入大大提高了复合材料的承载能力,石墨、MoS2的加入减少PTFE复合材料的摩擦因数。利用扫描电子显微镜(SEM)对PTFE复合材料的摩擦面进行了观察。结果表明:实验中5%nano-SiC和3%MoS2填充PTFE复合材料的摩擦磨损性能最好,且在高载荷下的摩擦磨损性能尤为突出,具有一定的应用价值。     

腐蚀环境中纤维增强聚四氟乙烯复合材料的摩擦磨损性能研究

分别研究了不同含量碳纤维(CF)、玻璃纤维(GF)填充聚四氟乙烯（PTFE）复合材料在硫酸溶液中和干摩擦条件下的摩擦学性能,同时考察了PTFE复合材料在酸中的腐蚀行为,探讨了相关机理。结果表明,在酸中GF能够提高PTFE的耐磨性,比CF在提高PTFE耐磨性方面具有更好的优势。就酸溶液中的耐磨性和耐腐蚀性而言,15 %（质量分数,下同）是填料的最佳含量,此时GF和CF填充的PTFE,耐磨性分别较纯PTFE提高了7.7和4.4倍;当填料的含量超过15 %时,复合材料的耐磨性和耐腐蚀性均下降,主要是由于此时犁削和磨粒磨损是PTFE复合材料的主要磨损机制。由于酸溶液的冷却和润滑作用,硫酸溶液中PTFE复合材料的摩擦因数大幅降低,但酸溶液抑制了对磨面上转移膜的形成。     

Study on wear and friction behavior of graphite flake‐filled PTFE composites

The wear rate and coefficient of friction for graphite flake (GF)‐filled polytetrafluoroethylene (PTFE) composites were evaluated on a pin‐on‐disk wear tester under dry conditions. Scanning electron microscopy showed significant reduction in the abrasive wear of the composites. The wear rates of 5 and 10 wt % GF composites were reduced by more than 22 and 245 times, respectively, at sliding speed of 1 m/s. With increasing sliding distance from 1 to 8 km, the wear rate of pure PTFE decreased by 1.4 times whereas that of composites, it decreased up to three times. The significant decreased in wear rate and coefficient of friction might be attributed to the formation of a thin and tenacious transfer film on the counter‐surface. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Influence of PTFE as a solid lubricant on the mechanical,electrical, and tribological properties of CF-reinforced PC composites

The objective of this research was to study the effects of polytetrafluoroethylene (PTFE) as a solid lubricant on the mechanical, electrical, and tribological properties of carbon fiber (CF)-reinforced polycarbonate (PC) composites. Samples were prepared by means of single-screw extrusion and injection molding processes. The mechanical tests included tensile, flexural, and failing weight impact tests, while the electrical tests consisted of surface and volume resistivity tests. The tribological testing was conducted under dry sliding conditions using pin-on-disk configuration. The results showed that the addition of CF managed to significantly reduce the electrical resistivity as the CF loading approached 10–15 wt%. The addition of PTFE managed to reduce the resistivity of the composite, that is, from 4.51 to 0.53 × 10 (Ωcm). The incorporation of 15 wt%. CF resulted with an increase of 45% in tensile strength and 51.5% in flexural strength, while the addition of PTFE had a negative impact on both properties. It was shown that PTFE was able to reduce the friction coefficient, μ and wear rate, K up to 0.257 and 6.35 × 10⁶ (mm³/Nm), respectively, which can be attributed to the excellent abilities of PTFE to form transfer film. The composite consisting of 15 wt% CF and 10 wt%. PTFE showed highest improvement in term of electrical resistivity, and is deemed the most suitable composition for this study. Scanning electron microscopy was also carried out to further elucidate the fracture and wear mechanism of the PC/CF/PTFE composites.     

Preparation and tribological properties of carbon fibre reinforced poly(vinylidene fluoride) composites

Abstract

The current study examines the tribological performance of poly(vinylidene fluoride) (PVDF) and carbon fibre reinforced poly(vinylidene fluoride) (CF/PVDF) under dry sliding condition. Different contents of carbon fibres (CFs) were employed as reinforcement. All filled and unfilled polyimide composites were tested against CGr15 ball and representative testing was performed. The effects of CF content on tribological properties of the composites were investigated. The worn surface morphologies of neat PVDF and its composites were examined by scanning electron microscopy and the wear mechanisms were discussed. Moreover, all filled PVDFs have superior tribological characteristics to unfilled PVDFs. The optimum wear reduction was obtained when the content of CF is 20 vol.-%.     

The effect of carbon fiber content on the friction and wear properties of carbon fiber reinforced polyimide composites

The current study examines the tribological performance of polyimide and carbon fiber reinforced polyimide (CF/PI) under dry sliding condition. Different contents of carbon fibers were employed as reinforcement. All filled and unfilled polyimide composites were tested against CGr15 ball and representative testing was performed. The effects of carbon fiber content on tribological properties of the composites were investigated. The worn surface morphologies of neat PI and its composites were examined by scanning electron microscopy and the wear mechanisms were discussed. Moreover, all filled polyimides have superior tribological characteristics to unfilled polyimides. The optimum wear reduction was obtained when the content of carbon fiber is 20 vol %. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Tribological and mechanical properties of carbon‐nanofiber‐filled polytetrafluoroethylene composites

The effects of various filler concentrations (0.1, 0.5, 1, 1.5, 2, 2.5, and 3 wt %) on the tribological and mechanical properties of carbon‐nanofiber (CNF)‐filled polytetrafluoroethylene (PTFE) composites were studied. Moreover, the influence of various loads (50, 100, 150, and 200 N) and sliding velocities (0.692 and 1.39 m/s) on the friction and wear behaviors of the PTFE composites was investigated. The results showed that the friction coefficients of the PTFE composites decreased initially up to a 0.5 wt % filler concentration and then increased, whereas the antiwear properties of the PTFE composites increased by 1–2 orders of magnitude in comparison with those of pure PTFE. The composite with a 2 wt % filler concentration had the best antiwear properties under all friction conditions. The friction coefficients of the CNF/PTFE composites decreased with increases in the load and sliding velocity, whereas the wear volume loss of the PTFE composites increased. At the same time, the results also indicated that the mechanical properties of the PTFE composites increased first up to a 1 wt % filler concentration and then decreased as the filler concentration was increased above 1 wt %. In comparison with pure PTFE, the impact strength, tensile strength, and elongation to break of the PTFE composites increased by 40, 20, and 70%, respectively, at a 1 wt % filler concentration. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 2430–2437, 2007     

不同介质中聚四氟乙烯复合材料的摩擦磨损性能

分别在碱液、水、油和干摩擦条件下考察了碳纤维和玻璃纤维填充聚四氟乙烯复合材料的摩擦磨损性能。利用SEM观察了不同介质中磨损面和对摩面的形貌,并探讨了其磨损机理。结果表明,不同介质中摩擦系数的大小关系是μ干>μ水或油>μ碱,磨损率是W水>W干>W碱或油。水、碱和油都不同程度地阻止了转移膜的形成。碱液和油具有很好的冷却与润滑作用,摩擦系数低,磨损小;然而水分子降低了填料和基体的界面粘接强度,造成犁削和磨粒磨损加重。     

The Tribological Mechanism of Poly(Vinylidene Fluoride) Composites Reinforced with Carbon Fibers

The current study examines the tribological performance of poly(vinylidene fluoride) (PVDF) and carbon fiber-reinforced poly(vinylidene fluoride) (CF/PVDF) under dry sliding condition. Different contents of carbon fibers were employed as reinforcement. All filled and unfilled polyimide composites were tested against CGr15 ball and representative testing was performed. The effects of carbon fiber content on tribological properties of the composites were investigated. The worn surface morphologies of neat PVDF and its composites were examined by scanning electron microscopy (SEM) and the wear mechanisms were discussed. Moreover, all filled PVDFs have superior tribological characteristics to unfilled PVDFs. The optimum wear reduction was obtained when the content of carbon fiber is 20 vol%.     

碱液中晶须增强PEEK复合材料的摩擦磨损性能

研究了不同含量PTW增强PEEK复合材料在碱液中的摩擦磨损性能,并与经典的CF增强PEEK复合材料对比,借助于SEM分析了磨损面和对偶面微观形貌,探讨了相关机理。结果表明,干摩擦时15%(质量)PTW增强PTFE/PEEK复合材料耐磨性是相同含量CF增强时的10.5倍。在碱液中,CF增加了PTFE/PEEK复合材料的摩擦系数、降低了其耐磨性能,而PTW可以进一步降低PTFE/PEEK复合材料的摩擦系数、明显地提高其耐磨性能。含5%PTW可提高PTFE/PEEK复合材料碱液中耐磨性2.36倍。碱液阻止了对偶面转移膜的形成,犁削和磨粒磨损是CF增强PEEK复合材料碱液中的主要磨损机制,而隧道状晶体结构和细微尺寸的纤维态形貌使得PTW在碱液中仍具有显微增强耐磨作用。     

The mechanical and tribological properties of PTFE filled with PTFE waste powders

Polytetrafluoroethylene (PTFE) composites filled with PTFE waste offer interesting combination of tribological properties and low cost. PTFE composites waste was mechanically cut and sieved into powders. PTFE composites filled with PTFE waste powders were prepared by compression molding. Friction and wear experiments were carried out in a reciprocating sliding tribotester at a reciprocating frequency of 1.0 Hz, a contact pressure of 5.5 MPa, and a relative humidity of (60 ± 5)%. PTFE materials slid against a 45 carbon steel track. Results showed that a PTFE composite (B) filled with 20 wt % PTFE waste exhibited a coefficient of steady‐state friction slightly higher than that of unfilled PTFE (A), while wear resistance over two orders of magnitude higher than that of unfilled PTFE (A). Another PTFE composite filled with PTFE waste and alumina nanoparticles exhibited the highest wear resistance among the three PTFE materials. This behavior originates from the effective reinforcement of PTFE waste as a filler. It was experimentally confirmed that the low cost recycling of PTFE waste without by‐products is feasible. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1035–1041, 2007     

A study on the tribological behavior of hybrid PTFE/Kevlar fabric composites filled with nano‐SiC and/or submicron‐WS2 fillers

The tribological behaviors of hybrid PTFE/Kevlar fabric composites filled with nano‐SiC and/or submicron‐WS₂ fillers were studied. Scanning electron microscopy and energy‐dispersive X‐ray spectrometer were used for analysis of the worn surface, transfer film, and debris of the PTFE/Kevlar fabric composites. In addition, the wear volume loss of the composite was measured by means of a laser microscopic 3D and profile measurement apparatus. The results indicate that although both single fillers and hybrid fillers can reduce the wear rate of composites, but hybrid fillers filled composites could achieve the desired comprehensive tribological properties in dry sliding. The improved tribological performance of filled composites can be attributed to two aspects: the formation of a thin and tenacious transfer film on the counter‐surface, and the restrain the formation of larger debris. Tiny wear debris was easily trapped in the gap of a worn surface and can repair the damaged surface. In addition, the trapped debris could be considered as a secondary source of lubricant. POLYM. COMPOS., 37:2218–2226, 2016. © 2015 Society of Plastics Engineers     

The Tribological Properties of Oxidation-Treated Carbon Fiber-Reinforced PTFE Composite under Oil-Lubricated Conditions

The effect of air-oxidation and ozone surface treatment of carbon fibers (CF) on tribological properties of CF reinforced Polytetrafluoroethylene (PTFE) composites under oil-lubricated condition was investigated. Experimental results revealed that ozone treated CF reinforced PTFE (CF/PTFE) composite had the lowest friction coefficient and wear. X-ray photoelectron spectroscopy (XPS) study of carbon fiber surface showed that the increase in the amount of oxygen-containing groups enhanced interfacial adhesion between CF and PTFE matrix. With strong interfacial adhesion of the composite, stress could be effectively transmitted to carbon fibers; carbon fibers were strongly bonded with PTFE matrix.     

Influence of solid lubricant reinforcement on wear behavior of Kevlar fabric composites

The friction and wear behavior of Kevlar fabric composites reinforced by PTFE or graphite powders was investigated using a Xuanwu‐III friction and wear tester at dry sliding condition, with the unfilled Kevlar fabric composite as a reference. The worn surfaces were analyzed by means of scanning electron microscope, and X‐ray photoelectron spectroscopy. It was found that PTFE or graphite as fillers could significantly improve the tribological behavior of the Kevlar fabric composites, and the Kevlar fabric composites filled with 20% PTFE exhibited the best antiwear and antifriction ability among all evaluated cases. The transfer films established with two lubricants in sliding wear of composites against metallic counterparts made contributions to reducing friction coefficient and wear rate of Kevlar fabric composites. In particular, FeF₂ generated in the sliding of Kevlar fabric composites filled with PTFE against counterpart pin improved the bonding strength between the transfer film and counterpart surface, which accounted for the lowest friction coefficient and wear rate of the Kevlar fabric composites filled with PTFE measured in the testing. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008.     

Tribological properties of PTFE‐filled PMIA

The polytetrafluoroethylene‐filled (PTFE) poly(m‐phenylene isophalamide) (PMIA) composite blocks are prepared by compression molding. The friction and wear of PTFE‐filled PMIA are investigated on a block‐on‐ring machine by running the PMIA composite block against plain carbon steel (AISI 1045 steel ring). The worn surface of PMIA composite and the steel counterface are examined by using electron probe microanalysis (EPMA). It is found that PTFE‐filled PMIA exhibited considerably lower friction coefficient and wear rate than pure PMIA. Furthermore, the lowest wear rate is obtained when the composite contains 20 vol % PTFE. EPMA investigations show that there are some debris that could restrain the wear of the PMIA composites oriented along the sliding track and embedded in the surface of PMIA composite. A kind of stripe transfer film that contains abundant F element should be the main reason for the improvement of the tribological properties of PTFE‐filled PMIA composites. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 747–751, 1999     

Friction and wear properties of basalt fiber reinforced/solid lubricants filled polyimide composites under different sliding conditions

Short basalt fibers (BFs)‐reinforced polyimide (PI) composites filled with MoS₂ and graphite were fabricated by means of hot‐press molding technique. The tribological properties of the resulting composites sliding against GCr15 steel ring were investigated on a model ring‐on‐block test rig. The wear mechanisms were also comparatively discussed, based on scanning electron microscopic examination of the worn surface of the PI composites and the transfer film formed on the counterpart. Experimental results revealed that MoS₂ and graphite as fillers significantly improved the wear resistance of the BFs‐reinforced polyimide (BFs/PI) composites. For the best combination of friction coefficient and wear rate, the optimal volume content of MoS₂ and graphite in the composites appears to be 40 and 35%, respectively. It was also found that the tribological properties of the filled BFs/PI composites were closely related with the sliding conditions such as sliding speed and applied load. Research results show that the BF/PI composites exhibited better tribological properties under higher PV product. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effects of various kinds of fillers on the tribological behavior of polytetrafluoroethylene composites under dry and oil‐lubricated conditions

Polytetrafluoroethylene (PTFE)‐based composites filled with various inorganic fillers in a volume fraction of 30% were prepared. The tribological behavior of the PTFE composites sliding against AISI52100 steel under dry and liquid paraffin‐lubricated conditions was investigated on an MHK‐500 model ring‐on‐block test rig. The morphologies of worn surfaces and wear debris were observed with a scanning electron microscope (SEM) and an optical microscope. As the results, different fillers show different effects on the tribological behavior of the PTFE composites, while the composite shows much different tribological behavior under lubricated conditions as compared with dry sliding. The tribological behavior of the PTFE composites under dry sliding is greatly related to the uniformity and thickness of the transfer films. Only the PTFE composites with a transfer film of good uniformity and proper thickness may have excellent tribological behavior. The PTFE composites show much better tribological behavior under lubrication of liquid paraffin than under dry sliding, namely, the friction coefficients are decreased by 1 order of magnitude and the wear rate by 1–3 orders of magnitude. Observation of the worn composite surfaces with SEM indicates that fatigue cracks were generated under lubrication of liquid paraffin, owing to the absorption and osmosis of liquid paraffin into the microdefects of the PTFE composites. The creation and development of the fatigue cracks led to fatigue wear of the PTFE composites. This would reduce the mechanical strength and load‐supporting capacity of the PTFE composites. Therefore, the tribological behavior of the PTFE composites under lubrication of liquid paraffin is greatly dependent on the compatibility between the PTFE matrix and the inorganic fillers. In other words, the better is the compatibility between PTFE and fillers the better is the tribological behavior of the composites. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 1891–1897, 2001