Preparation of polylactide/graphene composites from liquid‐phase exfoliated graphite sheets

Polylactide (PLA)/graphene nanocomposites were prepared by a facile and low‐cost method of solution‐blending of PLA with liquid‐phase exfoliated graphene using chloroform as a mutual solvent. Transmission electron microscopy (TEM) was used to observe the structure and morphology of the exfoliated graphene. The dispersion of graphene in PLA matrix was examined by scanning electron microscope, X‐ray diffraction, and TEM. FTIR spectrum and the relatively low I_D/I_G ratio in Raman spectroscopy indicate that the structure of graphene sheets (GSs) is intact and can act as good reinforcement fillers in PLA matrix. Thermogravimetric analysis and dynamic mechanical analysis reveal that the addition of GSs greatly improves the thermal stability of PLA/GSs nanocomposites. Moreover, tensile strength of PLA/GSs nanocomposites is much higher than that of PLA homopolymer, increasing from 36.64 (pure PLA) up to 51.14 MPa (PLA/GSs‐1.0). POLYM. COMPOS., 35:396–403, 2014. © 2013 Society of Plastics Engineers     

Compatibilizing effect of halloysite nanotubes in polar–nonpolar hybrid system

This article explores the effect of halloysite nanotubes (HNTs) and modified HNTs (M‐HNTs) on the properties of immiscible blend system based on polar polyoxymethylene (POM) and nonpolar polypropylene (PP) polymers. HNTs have been modified by N‐(β‐aminoethyl)‐γ‐aminopropyltrimethoxysilane (APTMS). Modification is confirmed by Fourier transform infrared spectroscopy (FTIR), also FTIR confirms the interaction between polymer blend and HNTs/M‐HNTs. Morphology of the nanocomposites are demonstrated by scanning electron microscope (SEM) and dispersion of HNTs/M‐HNTs are observed by transmission electron microscope (TEM). In nanocomposites, average dispersed domain sizes reduce in the presence of HNTs/M‐HNTs but significant reduction has been observed in the case of M‐HNT‐filled nanocomposites rather than unmodified HNT‐filled nanocomposites. The M‐HNT acts as a reinforcing agent as well as bridging tool in polar–nonpolar hybrid system. Modification of HNTs brings compatibility in between the blend partners and reveals improved dynamic mechanical, thermal, and tensile properties than that of the pure blend system. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39587.     

Influence of nanozirconia on the thermal stability of poly(methyl methacrylate) prepared by in situ bulk polymerization

Nanozirconia (nano‐ZrO₂) was prepared by the sol–gel method and incorporated into poly(methyl methacrylate) (PMMA) by the in situ bulk polymerization of methyl methacrylate. The structure of the nano‐ZrO₂ was confirmed by X‐ray diffraction (XRD), transmission electron microscopy, and Fourier transform infrared (FTIR) spectroscopy. The structure of the nano‐ZrO₂ nanocomposites were studied by differential scanning calorimetry, FTIR spectroscopy, XRD, and scanning electron microscopy, and the results show that there were interactions between the nanoparticles and the polymer. The influence of the nano‐ZrO₂ on the thermal stability of PMMA was investigated by thermogravimetric analysis (TGA). The results indicate that nano‐ZrO₂ enhanced the thermal stability of the PMMA/nano‐ZrO₂ nanocomposites. The effects of the heating rate in dynamic measurements (5–30°C/min) on kinetic parameters such as apparent activation energy (E_a) in TGA both in nitrogen and air were investigated. The Kissinger method was used to determine E_a for the degradation of pure PMMA and the PMMA/nano‐ZrO₂ nanocomposites. The kinetic results show that the values of E_a for the degradation of the nanocomposites were higher than that of pure PMMA in air. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Electrochemical synthesis and In situ spectroelectrochemistry of conducting NMPy‐TiO2 and ZnO polymer nanocomposites for Li secondary battery applications

Poly(N‐methylpyrrole) (PNMPy), poly(N‐methylpyrrole‐TiO₂) (PNMPy‐TiO₂), and poly (N‐methylpyrrole‐ZnO) (PNMPy‐ZnO) nanocomposites were synthesized by in situ electropolymerization for cathode active material of lithium secondary batteries. The charge–discharging behavior of a Li/LiClO₄/PNMPy battery was studied and compared with Li/LiClO₄/PNMPy‐nanocomposite batteries. The nanocomposites and PNMPy films were characterized by cyclic voltammetry, in situ resistivity measurements, in situ UV–visible, and Fourier transform infra‐red (FTIR) spectroscopy, scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The differences between redox couples (ΔE) were obtained for polymer nanocomposites and PNMPy films. During redox scan, a negative shift of potential was observed for polymer nanocomposite films. Significant differences from in situ resistivity of nanocomposites and PNMPy films were obtained. The in situ UV–visible spectra for PNMPy and polymer nanocomposite films show the intermediate spectroscopic behavior between polymer nanocomposites and PNMPy films. The FTIR peaks of polymer nanocomposite films were found to shift to higher wavelengths in PNMPy films. The SEM and TEM micrographs of nanocomposite films show the presence of nanoparticle in PNMPy backbone clearly. The result suggests that the inorganic semiconductor particles were incorporated in organic conducting PNMPy, which consequently modifies the properties and morphology of the film significantly. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41526.     

Thermal degradation behavior and gas phase flame‐retardant mechanism of polylactide/PCPP blends

The thermal degradation behavior of the blend based on polylactide (PLA) and poly(1,2‐propanediol 2‐carboxyethyl phenyl phosphinate) (PCPP) was investigated by the thermogravimetric analysis (TGA). Thermal degradation activation energies (E_a) of neat PLA and PLA/15% PCPP blend were calculated via the Flynn–Wall–Ozawa method. The E_a of the blends increased with the addition of PCPP increasing when the conversion was higher than 10%. In addition, the appropriate conversion models for the thermal degradation process of PLA and PLA/15% PCPP were studied via the Criado method. At the same time, the main gaseous decomposition products of PLA and its blend were identified by TGA/infrared spectrometry (TGA–FTIR) analysis. And it revealed that the PCPP improved the flame‐retardant property of PLA via altering the release of the flammable gas and nonflammable gas. Moreover, the PCPP improved the flame‐retardant property of PLA by inhibiting exothermic oxidation reactions in the combustion, which was further proved by pyrolysis–gas chromatography–mass spectrometry analysis. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40480.     

Sustained antioxidant properties of epigallocatechin gallate loaded halloysite for PLA as potentially durable materials

Halloysite nanotube (HNT) was etched by hydrochloric acid, and epigallocatechin gallate (EGCG) was loaded into the etched HNT (HH) to prepare loaded antioxidant (HH-E) for polylactic acid (PLA) with improved thermal-oxidative stability. The loading process was confirmed by TGA and FT-IR, and the loading capacity was 16.15%. The presence of EGCG on the surface of etched HNT was further confirmed by nitrogen adsorption and TEM. The effect of loaded EGCG on thermal-oxidative stability of PLA was characterized by the change in OOT values of PLA after the aging process under 140°C. The results showed that HH-E increased OOT values of PLA from 231.2°C to 293.6°C at first, indicating that HH-E provided PLA with excellent thermal-oxidative stability. Furthermore, as can be seen from the trend of OOT changing over aging time, during the 14 days aging process, OOT values of PLA composites with HH-E decreased more slowly than that of PLA composites with EGCG alone, endowing PLA with sustainable thermal-oxidative stability. Further kinetic analysis showed that the apparent activation energy of the degradation process (E_a) of PLA composites with HH-E changed less than that of PLA composites with EGCG alone, which showed that the loading system provided PLA better sustainable stability. Moreover, the isothermal crystallization process of modified PLA was characterized by DSC and POM. The results showed that HH-E provided heterogeneous crystal nucleus for PLA, reducing the half crystallization time (t_0.5) and improvement of crystallization rate for PLA. These results prove that HH-E exhibited excellent performance in improving the thermal stability and crystallization property of PLA, showing multifunctional characterization.     

Thermal and kinetic properties of poly(lactic acid) and transglutaminase‐crosslinked wheat gluten blends

Wheat gluten (10 g) was crosslinked (XL) using 10 units of transglutaminase. Different blends of XL gluten and poly(lactic acid) (PLA) were mixed in a Brabender mixer at 180°C for 10 min. Neat PLA and blends were analyzed using modulated DSC (MDSC). Neat PLA displayed a glass transition (T_g) and exothermic (Cry) followed by endothermic (Mel) transitions. The profile showed a T_g of 0.46 J/g/°C, Cry with 29.9 J/g, whereas Mel exhibited 28.7 J/g. XL wheat gluten displayed one T_g with 0.45 J/g/°C. Samples were subjected to repeated heating and cooling cycles to show the level of compatibility between the two polymers. The activation energy (E_a) and pre‐exponential factor (Z) were determined according to Borchardt and Daniels (B/D) kinetics approach. The blends showed increased E_a values with an increase in the amount of XL gluten. In the presence of 5 and 20% XL gluten, the E_a of PLA increased from 150 to 200 kJ/mol, respectively. A higher number of cycles caused an increase in E_a. The T_g temperature of different PLA/XL gluten blends can be predicted by Gordon–Taylor equation and its modified forms. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Nonisothermal crystallization kinetics of PLA/nanosized YVO4 composites as a novel nucleating agent

The influence of nanosized YVO₄ particles as a novel and efficient nucleating agent on the nonisothermal crystallization behaviors of poly(lactic acid) (PLA) was studied. A modified Avrami model was utilized to describe the nonisothermal crystallization kinetics of pure PLA and PLA nanocomposites. The differential isoconversional Friedmann formula was employed to calculate the effective activation energies (E_X(t) ) of nonisothermal crystallization from the glass state. The results showed that modified Avrami methods describe the nonisothermal crystallization kinetics of pure PLA and PLA nanocomposites well. The crystallization rate of PLA/1 mass% YVO₄ was faster than that of pure PLA sample by factor 5 × 10³ at a heating rate of 1 K min⁻¹. While the values of Lauritzen–Hoffman parameters (K_g and U*) of the PLA/YVO₄ nanocomposites were lower than those of pure PLA, indicating the nucleation efficiency of nanosized YVO₄ particles for PLA. Scanning electron microscopy images reflect the uniform dispersion of 1 mass% YVO₄ in PLA matrix. Thermogravimetric analysis results revealed that the thermal degradation parameters are slightly lowered by 7 °C on increasing the mass percentage of YVO₄ in the PLA nanocomposites. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48340.     

Synthesis and antimicrobial activity of the Schiff base from polyoxyalkylene‐montmorillonite nanocomposites and aldehydes

Vanillin (4‐hydroxy‐3‐methoxy benzaldehyde) and 5‐formylamino salicylic acid microbicides were reacted with polyoxyalkylene‐montmorillonite (D_230–2000‐MMT) nanocomposites. The microstructure of these Schiff base nanocomposites was characterized by TEM and XRD. D_230–2000‐MMT nanocomposites were prepared by an ion exchange process of sodium montmorillonite (Na‐MMT) and NH₃ ⁺ groups in polyoxyalkylene amine hydrochloride with three different molecular masses of D₂₃₀, D₄₀₀, and D₂₀₀₀. Wide‐angle X‐ray diffraction confirms the intercalation of the polymer between the silicate layers. Electrostatic interaction between the positively charged NH₃ ⁺ groups and the negatively charged surface of MMT was observed. The nanocomposites were tested for antimicrobial activity against the Gram‐negative bacteria (Escherichia coli NCIM 2065), Gram‐positive bacteria (Bacillus subtillus ATCC), and fungi (Candida albicans SC5314 and Cryptococcus neoformans). The D₂₀₀₀‐MMT/vanillin Schiff base nanocomposite strongly inhibited the growth of all microorganisms that can be used in different applications. The amount of loaded polymer and the structure of the nanocomposite play an important role in inhibiting the bacterial and fungal strains. It is found that the Schiff base nanocomposite affect the morphology, oxygen consumption, and the release of cytoplasmic constituents such as potassium (K⁺), sodium (Na⁺), and calcium (Ca²⁺) ions leading to death of the cells. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Nonisothermal crystallization kinetics and thermomechanical properties of multiwalled carbon nanotube‐reinforced poly(ε‐caprolactone) composites

BACKGROUND: The technological development of poly(ε‐caprolactone) (PCL) is limited by its short useful lifespan, low modulus and high crystallinity. There are a few papers dealing with the crystallization behavior of carbon nanotube‐reinforced PCL composites. However, little work has been done on the crystallization kinetics of melt‐compounded PCL/multiwalled carbon nanotube (MWNT) nanocomposites. In this study, PCL/MWNT nanocomposites were successfully prepared by a simple melt‐compounding method, and their morphology and mechanical properties as well as their crystallization kinetics were studied. RESULTS: The MWNTs were observed to be homogeneously dispersed throughout the PCL matrix. The incorporation of a very small quantity of MWNTs significantly improved the storage modulus and loss modulus of the PCL/MWNT nanocomposites. The nonisothermal crystallization behavior of the PCL/MWNT nanocomposites exhibits strong dependencies of the degree of crystallinity (X_c), peak crystallization temperature (T_p), half‐time of crystallization (t_1/2) and Avrami exponent (n) on the MWNT content and cooling rate. The MWNTs in the PCL/MWNT nanocomposites exhibit a higher nucleation activity. The crystallization activation energy (E_a) calculated with the Kissinger model is higher when a small amount of MWNTs is added, then gradually decreases; all the E_a values are higher than that of pure PCL. CONCLUSION: This paper reports for the first time the preparation of high‐performance biopolymer PCL/MWNT nanocomposites prepared by a simple melt‐compounding method. The results show that the PCL/MWNT nanocomposites can broaden the applications of PCL. Copyright © 2008 Society of Chemical Industry     

Morphology and thermal stabilization mechanism of LLDPE/MMT and LLDPE/LDH nanocomposites

The morphology and thermal stabilization mechanism of polymeric nanocomposites prepared by solution intercalation of linear low density polyethylene (LLDPE) with montmorillonite (MMT), MgAl layered double hydroxide (LDH), and ZnAl LDH have been studied by X-ray diffraction (XRD), transmission electron microscopy (TEM), dynamic Fourier transform infrared (FTIR) spectroscopy, and thermogravimetric analysis (TGA). Both LLDPE/MMT and LLDPE/MgAl LDH nanocomposites exhibit mixed intercalated-exfoliated structures, whereas the LLDPE/ZnAl LDH nanocomposites exhibit completely exfoliated structures because the ZnAl LDH layers can be easily broken during the refluxing process. All nanocomposites show significantly enhanced thermal stability compared with virgin LLDPE due to the increases of the effective activation energy (E_α) during degradation process. However, LDHs nanocomposites show much higher thermal degradation temperatures than MMT nanocomposites with the same filler content because they have much higher E_α than MMT nanocomposites at the early degradation stage. The data of real time FTIR spectroscopy and morphological evolution reveal a catalytic dehydrogenation effect presents in MMT nanocomposites, which may decrease the E_α of degradation and thermal stability of MMT nanocomposites.     

Preparation of poly(lactic acid)/poly(ethylene glycol)/organoclay nanocomposites by melt compounding

Poly(lactic acid) (PLA)/organoclay nanocomposites were prepared by melt compounding in a co‐rotating twin screw extruder. Two types of commercialized organoclay (dimethyl benzyl stearyl ammonium ion and dimethyl distearyl ammonium ion intercalated between clay platelets named as Clay A and Clay B, respectively) and two grades of poly(ethylene glycol) (PEG) with different molecular weight (M_w = 2,000 and 300,000–500,000 named as PEG2k and PEG500k, respectively) were used in this study. The Young's modulus improved by the addition of organoclay to PLA matrix. The Young's modulus decreased with the addition of PEG to PLA/organoclay nanocomposites. The tensile strength and elongation of PLA/Clay B nanocomposites increased with the addition of PEG2k. The effect of the addition of PEG on d‐spacing of PLA/organoclay nanocomposites is dependent upon the kind of organoclay. The sizes of clay agglomerations in PLA/PEG/organoclay nanocomposites are larger than those of PLA/organoclay ones in the same organoclay. Addition of PEG to PLA/organoclay nanocomposites during melt compounding will not be useful for the preparation of PLA/organoclay having fully exfoliated clay platelets. The shear thinning properties of the nanocomposites are independent of the addition of PEG. On the whole, PEG2k is good plasticizer for PLA/organoclay nanocomposites. POLYM. COMPOS. 27:256–263, 2006. © 2006 Society of Plastics Engineers     

Effects of halloysite nanotubes on the performance of plasticized poly(lactic acid)‐based composites

The objective of this study is processing and characterization of Halloysite nanotube (HNT)/poly(lactic acid) (PLA) nanocomposites. As HNT filler, a domestic source was used (ESAN HNT). The results obtained from this HNT were compared with a well‐known reference HNT (Nanoclay HNT). To achieve the desired physical properties and clay dispersion, composites were compounded via direct melt mixing in a laboratory twin‐screw compounder. However, the constituents were observed to be incompatible without a compatibilizer. To improve the flexibility of nanocomposites and provide compatibilization between PLA and HNT, two types of blends were prepared: PLA plasticized with poly(ethylene glycol) (PEG) denoted as P‐PLA and PLA toughened with a thermoplastic polyurethane (TPU) denoted as T‐PLA. Despite the limited improvement in the P‐PLA blends, TPU addition improved the flexibility of PLA/HNT without deteriorating the tensile strength in a great manner. This was attributed to the relatively better compatibilization effect of TPU and the role of nanotubes acting as bridges between the TPU and PLA phases. POLYM. COMPOS., 37:3134–3148, 2016. © 2015 Society of Plastics Engineers     

Thermal properties of extruded injection‐molded poly(lactic acid) and milkweed composites: Degradation kinetics and enthalpic relaxation

To determine the degree of compatibility between poly(lactic acid) (PLA) and different biomaterials, PLA was compounded with milkweed fiber, a new crop oil seed. After oil extraction, milkweed remaining cake retained approximately 10% residual oil, 47% protein, and 10% moisture. The fiber (300 μm) was added at 85 : 15 and 70 : 30 PLA : Fiber and blended by extrusion (EX) followed by injection molding (IM). Differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were used for testing the composites. After melting in the DSC sealed pans, composites were cooled by immersion in liquid nitrogen and aged (stored) at room temperature for 0, 7, 15, and 30 days. After storage, samples were heated from room temperature to 180°C at 10°C/min. The pure PLA showed a glass transition (T_g) at 60.3°C and the corresponding ΔCp was 0.464 J/g/°C followed by crystallization and melting transitions. The enthalpic relaxation (ER) of neat PLA and composites steadily increased as a function of storage time. Although the presence of fiber had little effect on ER, IM reduced it. The percentage crystallinity of neat unprocessed PLA dropped by 95 and 80% for the EX and IM, respectively. The degradation activation energy (E_a) of neat PLA exhibited a significant drop in nitrogen environment, whereas increased in air, indicating PLA resistant to heat degradation in the presence of oxygen. Overall, IM appeared to decrease E_a of the composites, whereas milkweed significantly reduced E_a values in nitrogen environment. Enzymatic degradation of the composites revealed higher degradation rate for the EX samples versus IM, whereas 30% milkweed exhibited higher weight loss compared to the 15%. The degradation mechanism was observed by looking at the percent conversion as a function of E_a from the TGA data, where multisteps degradation occurred mostly in air. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Structure and properties of polypropylene/hydrotalcite nanocomposites

This article presents the study of the modification of the particle/matrix interface region and its effects on the structure and dynamic mechanical behavior of polypropylene (PP)/hydrotalcite nanocomposites prepared by melt extrusion. The interface modification was promoted by combinying the organophillization of the hydrotalcite particles with blending the PP with a maleic anhydride‐grafted‐PP (PP‐g‐MAH) or a maleic anhydride‐grafted‐poly(styrene‐co‐ethylenebutylene‐co‐styrene) (SEBS‐g‐MAH). Sodium dodecyl sulphate was used to promote the organophillization of the hydrotalcite particles. X‐ray diffraction (XRD) and transmission electron microscopy (TEM) showed a partially exfoliated hydrotalcite structure, with an increasing exfoliation being achieved by adding a compatibilizer and organo‐modifying the particles. Values of the Young's modulus (E), storage modulus (E′), maximum tensile strength (σ_max), neck propagation strength (σ_neck), and elongation at break (ε_b) were found to depend both on the nature of the particle matrix interface as well as on the type of compatibilizer. Also, nanocomposites prepared with the organophillized particles showed lower T_g and loss factor values. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers     

Effects of the orientation of smectite particles and ionic strength on diffusion and activation enthalpies of I and Cs ions in compacted smectite

The apparent diffusion coefficients (D_a) for I⁻ and Cs⁺ ions in compacted Na-smectite which is a major constituent clay mineral of bentonite were studied as a function of smectite's dry density (0.9–1.4 Mg/m³), ionic strength ([NaCl] = 0.01, 0.51 M), temperature (22–60 °C) and diffusion direction to the orientated direction of smectite particles. The Na-smectite was prepared by ion-exchanging with Na⁺ ions a Na-bentonite, Kunipia-F®, of which smectite content is over 99 wt.%. The D_a-values for both ions showed a tendency to be higher in the parallel direction than in the perpendicular direction to the orientated direction of smectite particles at a low-ionic strength of [NaCl] = 0.01 M. The D_a-values for I⁻ ions showed different trends depending on diffusion direction and dry density at a high-ionic strength of [NaCl] = 0.51 M. Namely, although the D_a-values for I⁻ ions showed a tendency to be higher in the parallel direction than in the perpendicular direction to the orientated direction of smectite particles at a high-dry density of 1.4 Mg/m³, these showed a reciprocal tendency at dry densities of 0.9–1.0 Mg/m³. The D_a-values for Cs⁺ ions uniformly increased with an increase of ionic strength in both diffusion directions. Considering electrostatic effect from smectite surface and the change in tortuosity on dry density, ionic strength and diffusion direction to the orientated direction of smectite particles, I⁻ ions are considered to mainly diffuse in interstitial pores. While, Cs⁺ ions can diffuse in both interlayer and interstitial pores, and the D_a-values are considered to have elevated by competing with Na⁺ ions. The activation enthalpies (ΔE_a) for I⁻ ions, slightly higher (ΔE_a = 19.8−20.0 kJ/mol) than that of the diffusion coefficient in free water (D^o) for I⁻ ions (ΔE_a = 17.36 kJ/mol) at a low-ionic strength of [NaCl] = 0.01 M, decreased with an increase of ionic strength, became of similar level to that of the D^o at a high-ionic strength of [NaCl] = 0.51 M, increased with an increase of dry density. On the contrary, the ΔE_a-values for Cs⁺ ions, clearly higher (ΔE_a = 25.6−28.4 kJ/mol) than that of the D^o for Cs⁺ ions (ΔE_a = 16.47 kJ/mol) even in low-dry density over the ionic strength, increased with an increase of dry density. The ΔE_a-values for Cs⁺ ions are considered to be due to the decrease in the activity of porewater in addition to the effect of ion exchange enthalpy between Cs⁺ and Na⁺ ions in smectite.     

Influence of symmetry/asymmetry of the nanoparticles structure on the thermal stability of polyhedral oligomeric silsesquioxane/polystyrene nanocomposites

The thermal degradation of two polyhedral oligomeric silsesquioxane/polystyrene (POSS/PS) nanocomposites of formula R₈(SiO_1.5)₈ POSS/PS and R′₁R₇(SiO_1.5)₈ POSS/PS (where R′ = Phenyl and R = Cyclopentyl), at 5% of POSS concentration, was studied in both inert (flowing nitrogen) and oxidative (static air) atmospheres. Compounds were prepared by the polymerization of styrene in the presence of POSS. Degradations were carried out into a thermobalance, in the scanning mode, at various heating rates, and the obtained thermogravimetric (TG) curves were discussed and interpreted. The initial decomposition temperature (T_i), the temperature at 5% mass loss (T_5%), the glass transition temperature (T_g), and the activation energy (E_a) of degradation of nanocomposites were determined and compared with each other and with those of unfilled PS. The T_i, T_5%, and degradation E_a values of nanocomposites were higher than those of neat PS, thus indicating a better heat resistance and lower degradation rate, and then a better overall thermal stability. The use of POSS with a symmetric structure, in the synthesis of PS based nanocomposite, showed a decrease of T_g value not only in respect to asymmetric POSS/PS nanocomposite but also in respect to neat polymer, thus suggesting an influence of filler structure in the thermal properties of the materials. POLYM. COMPOS., 33:1903–1910, 2012. © 2012 Society of Plastics Engineers     

Mechanical Properties and Degrading Behaviors of Aluminum Hypophosphite-Poly(Lactic Acid) (PLA) Nanocomposites

The flame retardancy of poly(lactic acid) (PLA)/aluminum hypophosphite (AHP, phosphorous content = 41.87 wt.%) nanocomposites (PLA/(AHP-x), x = 15%, 20%, 25%; and x denotes the weight percentage content of AHP) was greatly enhanced by melt blending of AHP into PLA through twin-screw extruder and injection-molding process. The UL 94 V-0 flammability rating can be reached for PLA/(AHP-20%) with the LOI value over 28.8. The well dispersion of the AHP in PLA/(AHP-x) was investigated by FT-IR spectra under the line mapping model. Based on TGA results under a non-isothermal condition, the thermal degradation kinetics of PLA/(AHP-x) composites were studied by Kissinger’s, Ozawa’s and Flynn-Wall-Ozawa’s (FWO’s) methods. And those thermal degradation dynamic analyses showed lower activation energy (E_K or E_O) (from 155 to 122 kJ·mol^–1) corresponded to higher content of AHP (from 15 to 25 wt.%) for PLA/(AHP-x) nanocomposites. Kissinger’s, FWO’s and Coast-Redfern’s methods were used to discriminate the kinetic models and kinetic parameters for the thermal degradation of PLA/(AHP-x), which suggested conversion function G (α) = [-ln(1-α)]^2/3 or G (α) = α for the investigated process. The flame retardant PLA nanocomposites obtained in this study will become safety environment-friendly potential candidates in household and automobile engineering with high performance.     

Polylactide/transition metal ion modified montmorillonite nanocomposite—a critical evaluation of mechanical performance and thermal stability

Polylactide (PLA) nanocomposite was prepared by melt blending of PLA and transition metal ion (TMI) adsorbed montmorillonite (MMT). PLA nanocomposite was characterized for mechanical performance, and the results revealed that the tensile modulus, flexural modulus, and impact strength were increased marginally. The nanocomposite was optimized at 5 wt% of TMI‐modified MMT (TMI‐MMT) loading. Thermogravimetric analysis displayed increase in onset of degradation temperature, and differential scanning calorimetry showed marginal increase in glass transition temperature (T_g) and melting temperature (T_m) in case of PLA nanocomposites, when compared with virgin PLA. The flammability testing of nanocomposites indicated good fire retardance characters. X‐ray diffraction patterns of TMI‐MMT and the corresponding nanocomposites indicated an intercalation of the metal ions into the clay interlayer. Fourier transform infrared spectroscopy analysis indicate formation of [Zn(EDA)₂]²⁺ and [Cu(EDA)₂]²⁺ complexes in the MMT interlayer. Dynamic mechanical analysis shows increase in glass transition temperature (T_g) and storage modulus (E′) in case of PLA nanocomposites reinforced with 5 wt% modified MMT. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Surface‐modified halloysite nanotubes reinforced poly(lactic acid) for use in biodegradable coronary stents

Poly(lactic acid) (PLA) was reinforced halloysite nanotubes (HNTs) in this study. To improve dispersion and interfacial adhesion of HNTs within the PLA matrix, HNTs were surface modified with 3‐aminopropyltriethoxysilane (ASP) prior to compounding with PLA. PLA/ASP‐HNTs nanocomposites were characterized by differential scanning calorimetry (DSC), Fourier transfer infrared spectroscopy (FTIR), surface wettability, thermogravimetric analysis, transmission electron microscopy (TEM), and tensile testing. The hemocompatibility and cytocompatibility of PLA and PLA composites were investigated and the in vitro degradation process of PLA/ASP‐HNTs composites was investigated for a period of 6 months by gel permeation chromatography, FTIR, weight loss measurement, DSC, and tensile testing. PLA and all PLA composites were blood compatibile and non‐cytotoxic. TEM analysis revealed that HNTs agglomeration in PLA matrix was reduced by surface treatment with ASP. ASP‐HNTs had better reinforcing effect than unmodified HNTs evidenced by tensile testing. ASP‐HNTs appeared to increase the hydrolytic degradation process as measured by weight measurement. PLA/ASP‐HNTs composites displayed 12.1% weight loss and 30.6% average molecular weight reduction while retaining 74% of Young's modulus by the 24th week of degradation. Based on this data, the reinforcement of PLA using ASP‐HNTs may prove beneficial for applications such as biodegradable stents. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46521.