Structural and electrical properties of Al doped ZnO thin films deposited at room temperature on poly(vinilidene fluoride) substrates

Transparent, conducting, Al-doped ZnO films have been deposited, by dc and pulsed dc magnetron sputtering, on glass and electroactive polymer (poly(vinylidene fluoride)–PVDF) substrates. Samples have been prepared at room temperature varying the argon sputtering pressure, after optimizing other processing conditions. All ZnO:Al films are polycrystalline and preferentially oriented along the [002] axis. Electrical resistivity around 3.3 × 10^− 3 Ω cm and optical transmittance of ~ 85% at 550 nm have been obtained for AZOY films deposited on glass, while a resistivity of 1.7 × 10^− 2 Ω cm and transmittance of ~ 70% at 550 nm have been attained in similar coatings on PVDF. One of the main parameters affecting film resistivity seems to be the roughness of the substrate.     

High density plasma treatment of polyimide substrate to improve structural and electrical properties of Ga-doped ZnO films

We investigated the effects of a high density O₂ plasma treatment on the structural and electrical properties of sputter-deposited GZO films. The GZO films were deposited on polyimide substrate without substrate heating by RF magnetron sputtering from a ZnO target mixed with 5 wt.% Ga₂O₃. Prior to the GZO film growth, we treated a polyimide substrate with highly dense inductively coupled oxygen plasma. The optical transmittance of the GZO film, about 80%, was maintained regardless of the plasma pre-treatment. However, the resistivity of the film was strongly influenced by the plasma pre-treatment. The resistivity of the GZO film decreased from 1.02 × 10^− 2 Ω cm without an O₂ plasma pre-treatment to 1.89 × 10^− 3 Ω cm with an O₂ plasma pre-treatment.     

Electrical and optical properties of 12CaO·7Al2O3 electride doped indium tin oxide thin film deposited by RF magnetron co-sputtering

12CaO·7Al₂O₃ electride (C12A7:e⁻) doped indium tin oxide (ITO) (ITO:C12A7:e⁻) thin films were fabricated on a glass substrate by an RF magnetron co-sputtering system with increasing number of C12A7:e⁻ chips (from 1 to 7) and at various oxygen partial pressure ratios. The optical transmittance of the ITO:C12A7:e⁻ thin film was higher than 70% in the visible wavelength region. In the electrical properties of the thin film, a decrease of the carrier concentration from 2.6 × 10²⁰ cm^− 3 to 2.1 × 10¹⁸ cm^− 3 and increase of the resistivity from 1.4 × 10^− 3 Ω cm to 4.1 × 10^− 1 Ω cm were observed with increasing number of C12A7:e⁻ chips and oxygen partial pressure ratios. It was also observed that the Hall mobility was decreased from 17.27 cm²·V^− 1·s^− 1 to 5.13 cm²·V^− 1·s^− 1. The work function of the ITO thin film was reduced by doping it with C12A7:e⁻.     

Deposition of low-resistivity gallium-doped zinc oxide films by low-temperature radio-frequency magnetron sputtering

The transparent and conductive gallium-doped zinc oxide (GZO) film was deposited on 1737F Corning glass using the radio-frequency (RF) magnetron sputtering system with a GZO ceramic target. (The Ga₂O₃ contents are approximately 5 wt. %). In this study, the effect of the sputtering pressure on the structural, optical and electrical properties of GZO films upon the glass or polyester film (PET) substrate was investigated and discussed in detail. The GZO film was grown under a steady RF power of 400 W and a lower substrate temperature from room temperature up to 200 °C. The crystal structure and orientation of GZO thin films were examined by X-ray diffraction. All of the GZO films under various sputtering pressures had strong c-axis (002)-preferred orientation. Optical transparency was high (> 80%) over a wide spectral range from 380 nm to 900 nm. According to the experimental data, the resistivity of a single-layered GZO film was optimized at  8.3 × 10^− 4 Ω cm and significantly influenced by the sputtering pressure. In further research, the sandwich structure of the GZO film/Au metal/GZO film was demonstrated to improve the electrical properties of the single-layered GZO film. The resistivity of the sandwich-structured GZO film was around 2.8 × 10^− 4 Ω cm.     

Some physical properties of Sn-doped CdO thin films prepared by chemical bath deposition

Undoped and Sn-doped CdO thin films were prepared by the chemical bath deposition method by means of a procedure that improves the deposition efficiency. All as-grown films were crystallized in the cubic structure of cadmium peroxide (CdO₂) and transformed into CdO with a cubic structure after an annealing process. The as-grown films have a high resistivity (> 10⁶ Ω cm) and an optical bandgap around 3.6 eV. Undoped CdO displays an optical bandgap around 2.32–2.54 eV and has an electrical conductivity of 8 × 10^− 4 Ω cm. The Sn incorporation into CdO produces a blue shift in the optical bandgap (from 2.55 to 2.84 eV) and a decrease in the electrical conductivity.The deposition procedure described here gives colloid-free surface thin films as indicated by the surface morphology analysis.     

Polycrystalline films of tungsten-doped indium oxide prepared by d.c. magnetron sputtering

Electrical and optical properties of polycrystalline films of W-doped indium oxide (IWO) were investigated. These films were deposited on glass substrate at 300 °C by d.c. magnetron sputtering using ceramic targets. The W-doping in the sputter-deposited indium oxide film effectively increased the carrier density and the mobility and decreased the resistivity. A minimum resistivity of 1.8 × 10^− 4 Ω cm was obtained at 3.3 at.% W-doping using the In₂O₃ ceramic targets containing 7.0 wt.% WO₃. The 2.2 at.% W-doped films obtained from the targets containing 5.0 wt.% WO₃, showed the high Hall mobility of 73 cm² V^− 1 s^− 1 and relatively low carrier density of 2.9 × 10²⁰ cm^− 3. Such properties resulted in novel characteristics of both low resistivity (3.0 × 10^− 4 Ω cm) and high transmittance in the near-infrared region.     

Effect of oxygen pressure of SiOx buffer layer on the electrical properties of GZO film deposited on PET substrate

The present work was made to investigate the effect of oxygen pressure of SiO_x layer on the electrical properties of Ga-doped ZnO (GZO) films deposited on poly-ethylene telephthalate (PET) substrate by utilizing the pulsed-laser deposition at ambient temperature. For this purpose, the SiO_x buffer layers were deposited at various oxygen pressures ranging from 13.3 to 46.7 Pa. With increasing oxygen pressure during the deposition of SiO_x layer as a buffer, the electrical resistivity of GZO/SiO_x/PET films gradually decreased from 7.6 × 10^− 3 to 6.8 × 10^− 4 Ω·cm, due to the enhanced mobility of GZO films. It was mainly due to the grain size of GZO films related to the roughened surface of the SiO_x buffer layers. In addition, the average optical transmittance of GZO/SiO_x/PET films in a visible regime was estimated to be ~ 90% comparable to that of GZO deposited onto a glass substrate.     

Effect of the annealing temperature on transparency and conductivity of ZnO:Al thin films

Highly aluminum-doped zinc oxide (ZnO:Al) films were grown by rf-magnetron sputtering at low temperature from aerogel nanoparticles and characterized by structural, electrical and optical techniques. Nanoparticles with a size of about 30 nm were synthesized by sol–gel method using supercritical drying in ethyl alcohol and annealed at different temperatures with different gas atmospheres. The ZnO films were polycrystalline textured, preferentially oriented along the (002) crystallographic direction normal to the film surface. The films show within the visible wavelength region an optical transmittance of more than 90% and low electrical resistivity of 10^− 3 Ω cm at room temperature.     

Effect of oxygen flow rate on ITO thin films deposited by facing targets sputtering

Tin-doped indium oxide (ITO) thin films were deposited on glass substrates at various oxygen flow rates using a planar magnetron sputtering system with facing targets. In this system, the strong internal magnets inside the target holders confine the plasma between the targets. High resolution transmission electron microscopy revealed a combination of amorphous and crystalline phases on the glass substrate. X-ray photoelectron spectroscopy suggested that the decrease in carrier concentration and increase in mobility were caused by a decrease in the concentration of Sn⁴⁺ states. The electrical and optical properties of the ITO films were examined by Hall measurements and UV-visible spectroscopy, which showed a film resistivity and transmittance of 4.26 × l0⁻⁴ Ω cm, and > 80% in the visible region, respectively.     

Effects of deposition temperature on structure and properties of mo-doped indium oxide by radio frequency magnetron sputtering

Transparent conductive oxide (TCO) thin films of Mo-doped In₂O₃ (IMO) were prepared on glass substrates by radio frequency magnetron sputtering from the 2 wt% Mo-doped In₂O₃ ceramic target. The depositions were carried out under an oxygen-argon atmosphere by varying the deposition temperature from 200 °C to 350 °C. The crystal structure and thickness of IMO thin films were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The effects of deposition temperature on the electrical and optical transmittance properties of IMO thin films were investigated by four-point probe Hall system and UV-VIS-NIR spectrophotometer separately. The optimum deposited IMO thin films were obtained with resistivity of 6.9 × 10⁻⁴ Ω cm and carrier mobility 45 cm²v⁻¹s⁻¹ at 350 °C. The average optical transmittance of IMO films on glass substrates are over 80% in the near-infrared region.     

Structural and optoelectronic properties of Al-doped zinc oxide films deposited on flexible substrates by radio frequency magnetron sputtering

Al-doped zinc oxide (AZO) thin films were deposited onto flexible polyethylene terephthalate substrates, using the radio frequency (RF) magnetron sputtering process, with an AZO ceramic target (The Al₂O₃ content was about 2 wt.%). The effects of the argon sputtering pressure (in the range from 0.66 to 2.0 Pa), thickness of the Al buffer layer (thickness of 2, 5, and 10 nm) and annealing in a vacuum (6.6 × 10^− 4 Pa), for 30 min at 120 °C, on the morphology and optoelectronic performances of AZO films were investigated. The resistivity was 9.22 × 10^− 3 Ω cm, carrier concentration was 4.64 × 10²¹ cm^− 3, Hall mobility was 2.68 cm²/V s and visible range transmittance was about 80%, at an argon sputtering pressure of 2.0 Pa and an RF power of 100 W. Using an Al buffer decreases the resistivity and optical transmittance of the AZO films. The crystalline and microstructure characteristics of the AZO films are improved by annealing.     

Structural, electrical and optical properties of zirconium-doped zinc oxide films prepared by radio frequency magnetron sputtering

Transparent and conducting zirconium-doped zinc oxide films have been prepared by radio frequency magnetron sputtering at room temperature. The ZrO₂ content in the target is varied from 0 to 10 wt.%. The films are polycrystalline with a hexagonal structure and a preferred orientation along the c axis. As the ZrO₂ content increases, the crystallinity and conductivity of the film are initially improved and then both show deterioration. Zr atoms mainly substitute Zn atoms when the ZrO₂ content are 3 and 5 wt.%, but tend to cluster into grain boundaries at higher contents. The lowest resistivity achieved is 2.07 × 10^− 3 Ω cm with the ZrO₂ content of 5 wt.% with a Hall mobility of 16 cm² V^− 1 s^− 1 and a carrier concentration of 1.95 × 10²⁰ cm^− 3. All the films present a high transmittance of above 90% in the visible range. The optical band gap depends on the carrier concentration, and the value is larger at higher carrier concentration.     

Growth and characterization of indium tin oxide thin films deposited on PET substrates

Transparent and conductive indium tin oxide (ITO) thin films were deposited onto polyethylene terephthalate (PET) by d.c. magnetron sputtering as the front and back electrical contact for applications in flexible displays and optoelectronic devices. In addition, ITO powder was used for sputter target in order to reduce the cost and time of the film formation processes. As the sputtering power and pressure increased, the electrical conductivity of ITO films decreased. The films were increasingly dark gray colored as the sputtering power increased, resulting in the loss of transmittance of the films. When the pressure during deposition was higher, however, the optical transmittance improved at visible region of light. ITO films deposited onto PET have shown similar optical transmittance and electrical resistivity, in comparison with films onto glass substrate. High quality films with resistivity as low as 2.5 × 10^− 3 Ω cm and transmittance over 80% have been obtained on to PET substrate by suitably controlling the deposition parameters.     

Structural, electrochemical and optical comparisons of tungsten oxide coatings derived from tungsten powder-based sols

Tungsten trioxide (WO₃) electrochromic coatings have been formed on indium tin oxide-coated glass substrates by aqueous routes. Coating sols are obtained by dissolving tungsten powder in acetylated (APTA) or plain peroxotungstic acid (PTA) solutions. The structural evolution and electrochromic performance of the coatings as a function of calcination temperature (250 °C and 400 °C) have been reported. Differential scanning calorimetry and X-ray diffraction have shown that amorphous WO₃ films are formed after calcination at 250 °C for both processing routes; however, the coatings that calcined at 400 °C were crystalline in both cases. The calcination temperature-dependent crystallinity of the coatings results in differences in optical properties of the coatings. Higher coloration efficiencies can be achieved with amorphous coatings than could be seen in the crystalline coatings. The transmittance values (at 800 nm) in the colored state are 35% and 56% for 250 °C and 400 °C-calcined coatings, respectively. The electrochemical properties are more significantly influenced by the method of sol preparation. The ion storage capacities designating the electrochemical properties are found in the range of 1.62–2.74 × 10^− 3 (mC cm^− 2) for APTA coatings; and 0.35–1.62 × 10^− 3 (mC cm^− 2) for PTA coatings. As a result, a correlation between the microstructure and the electrochromic performance has been established.     

Optical properties of SnO2:F films deposited by atmospheric pressure CVD

Atmospheric pressure chemical vapor deposition (APCVD) system, designed for the deposition of F-doped SnO₂ thin films, is compatible with industrial requirements such as high process speed, scaling to wide substrate widths and low costs. Precise method for measuring the optical absorptance in the spectral range 300–1700 nm combines transmittance, reflectance and photothermal deflection (PDS) spectra measured on the same spot of the sample immersed in the transparent liquid with a relatively high index of refraction. The effects of the film thickness, doping gas addition and the susceptor temperature on the optical absorptance and electrical resistivity of the TCO films are assessed. We show that the doping gas concentration and the susceptor temperature influence both the incorporation ratio of dopants into SnO₂ film as well as the defect concentration. The SnO₂ films growth at optimum APCVD conditions have thickness 0.7 µm, average surface roughness about 40 nm, sheet electrical resistance 10 Ω/sq and the optical absorption 1% at 500 nm and about 5% at 1000 nm.     

Properties of indium tin oxide films deposited using High Target Utilisation Sputtering

Indium tin oxide (ITO) films were deposited on soda lime glass and polyimide substrates using an innovative process known as High Target Utilisation Sputtering (HiTUS). The influence of the oxygen flow rate, substrate temperature and sputtering pressure, on the electrical, optical and thermal stability properties of the films was investigated. High substrate temperature, medium oxygen flow rate and moderate pressure gave the best compromise of low resistivity and high transmittance. The lowest resistivity was 1.6 × 10^− 4 Ω cm on glass while that on the polyimide was 1.9 × 10^− 4 Ω cm. Substrate temperatures above 100 °C were required to obtain visible light transmittance exceeding 85% for ITO films on glass. The thermal stability of the films was mainly influenced by the oxygen flow rate and thus the initial degree of oxidation. The film resistivity was either unaffected or reduced after heating in vacuum but generally increased for oxygen deficient films when heated in air. The greatest increase in transmittance of oxygen deficient films occurred for heat treatment in air while that of the highly oxidised films was largely unaffected by heating in both media. This study has demonstrated the potential of HiTUS as a favourable deposition method for high quality ITO suitable for use in thin film solar cells.     

Influence of Ar/O2 ratio on the properties of transparent conductive ZnO:Ga films prepared by DC reactive magnetron sputtering

Ga-doped zinc oxide (ZnO:Ga) transparent conductive films with highly (002)-preferred orientation were deposited on glass substrates by DC reactive magnetron sputtering method in Ar + O₂ ambience with different Ar/O₂ ratios. The structural, electrical, and optical properties were investigated by X-ray diffraction, Hall measurement, and optical transmission spectroscopy. The resistivity and optical transmittance of the ZnO:Ga thin films are of the order of 10^− 4 Ω cm and over 85%, respectively. The lowest electrical resistivity of the film is found to be about 3.58 × 10^− 4 Ω cm. The influences of Ar/O₂ gas ratios on the resistivity, Hall mobility, and carrier concentration were analyzed.     

Low resistivity transparent conducting CdO thin films deposited by DC reactive magnetron sputtering at room temperature

Transparent conducting cadmium oxide (CdO) films were deposited on PET (polyethylene terephthalate) substrate by DC reactive magnetron sputtering at room temperature. All the films deposited at room temperature were polycrystalline in rock-salt structure. Dependences of the physical properties of the CdO films on the oxygen partial pressure were systematically studied. The films deposited at low oxygen flow rate were (200) oriented, while the films deposited at an oxygen flow rate greater than 20 sccm were (111) oriented. The average grain size of the CdO films decreased as the oxygen flow rate increases as determined by XRD and SEM. The Hall effect measurement showed that CdO films have high concentration, low resistivity, and high mobility. Both the mobility and the concentration of the carrier decreased with the increase of the oxygen flow rate. A minimum sheet resistance of 36.1 Ω/□, or a lowest resistivity of 5.44 × 10^− 4 Ω cm (6.21 × 10²⁰/cm³, μ = 19.2 cm²/Vs) was obtained for films deposited at an oxygen flow rate of 10 sccm.     

Effects of oxygen gas flow rate and ion beam plasma conditions on the opto-electronic properties of indium molybdenum oxide films fabricated by ion beam-assisted evaporation

The purpose of the present work is to experimentally study the effects of the oxygen gas flow rate and ion beam plasma conditions on the properties of indium molybdenum oxide (IMO) films deposited onto the polyethersulfone (PES) substrate. Crystal structure, surface morphology, and optoelectronic properties of IMO films are examined as a function of oxygen gas flow rate and ion beam discharge voltage.Experimental results show that the IMO films consist of a cubic bixbyite B-In₂O₃ single phase with its crystal preferred orientation alone B(222). Mo⁶⁺ ions are therefore considered to partially substitute In³⁺ sites in the deposit. Under-controlled ion bombardment during deposition enhances the reaction among those arriving oxygen and metal ion species to condense into IMO film and facilitates a decreased surface roughness of IMO film. The film with ultimate crystallinity and the lowest surface roughness is obtained when the oxygen flow rate of 3 sccm and the discharge voltage of 110 V are employed. This results in the lowest electrical resistivity due mainly to the increased Hall mobility and irrelevant to carrier concentration. The lowest electrical resistivity of 8.63 × 10^− 4 ohm-cm with a 84.63% transmittance at a wavelength of 550 nm can be obtained, which satisfies the requirement of a flexible transparent conductive polymer substrate.     

Ultrathin Al-doped transparent conducting zinc oxide films fabricated by pulsed laser deposition

Al-doped transparent conducting zinc oxide (AZO) films, approximately 20-110 nm-thick, were deposited on glass substrates at substrate temperatures between 200 and 300 °C by pulsed laser deposition (PLD) using an ArF excimer laser (λ = 193 nm). When fabricated at a substrate temperature of 260 °C, a 40-nm-thick AZO film showed a low resistivity of 2.61 × 10^− 4 Ω·cm, carrier concentration of 8.64 × 10²⁰ cm^− 3, and Hall mobility of 27.7 cm²/V·s. Furthermore, for an ultrathin 20-nm-thick film, a resistivity of 3.91 × 10^− 4 Ω·cm, carrier concentration of 7.14 × 10²⁰ cm^− 3, and Hall mobility of 22.4 cm²/V·s were obtained. X-ray diffraction (XRD) spectra, obtained by the θ-2θ method, of the AZO films grown at a substrate temperature of 260 °C showed that the diffraction peak of the ZnO (0002) plane increased as the film thickness increased from 20 to 110 nm. The full-width-at-half-maximum (FWHM) values were 0.5500°, 0.3845°, and 0.2979° for film thicknesses of 20, 40, and 110 nm, respectively. For these films, the values of the average transmittance in visible light wavelengths (400-700 nm) were 95.1%, 94.2%, and 96.6%, respectively. Field emission scanning electron microscopy (FE-SEM) and atomic force microscopy (AFM) observations showed that even the 20-nm-thick films did not show island structures. In addition, exfoliated areas or vacant and void spaces were not observed for any of the films.