New dielectric material system of La(Mg1/2Ti1/2)O3–Ca0.6La0.8/3TiO3 for microwave applications

The microstructure and microwave dielectric properties of xLa(Mg_1/2Ti_1/2)O₃–(1 − x)Ca_0.6La_0.8/3TiO₃ ceramics system with ZnO additions (0.5 wt.%) investigated by the conventional solid-state route have been studied. Doping with ZnO (0.5 wt.%) can effectively promote the densification and the dielectric properties of xLa(Mg_1/2Ti_1/2)O₃–(1 − x)Ca_0.6La_0.8/3TiO₃ ceramics. 0.6La(Mg_1/2Ti_1/2)O₃–0.4Ca_0.6La_0.8/3TiO₃ ceramics with 0.5 wt.% ZnO addition possess a dielectric constant (_r) of 43.6, a Q × f value of 48,000 (at 8 GHz) and a temperature coefficient of resonant frequency (τ_f) of −1 ppm/°C sintering at 1475 °C. As the content of La(Mg_1/2Ti_1/2)O₃ increases, the highest Q × f value of 62,900 (GHz) for x = 0.8 is achieved at the sintering temperature 1475 °C. A parallel-coupled line band-pass filter is designed and simulated using the proposed dielectric to study its performance.     

Study of (1 − x)(Mg0.6Zn0.4)0.95Co0.05TiO3–xCa0.61Nd0.26TiO3 microwave dielectrics

The microwave dielectric properties and the microstructures of the (1 − x)(Mg_0.6Zn_0.4)_0.95Co_0.05TiO₃–xCa_0.61Nd_0.26TiO₃ ceramic system were investigated. In order to achieve a temperature-stable material, we studied a method of combining a positive temperature coefficient material with a negative one. Ca_0.61Nd_0.26TiO₃ has a large positive temperature coefficient of resonant frequency. (Mg_0.6Zn_0.4)_0.95Co_0.05TiO₃ possesses a negative temperature coefficient of resonant frequency. By appropriately adjusting the x value in the (1 − x)(Mg_0.6Zn_0.4)_0.95Co_0.05TiO₃–xCa_0.61Nd_0.26TiO₃ ceramic system, a near-zero τ_f value can be obtained. A new microwave dielectric material of 0.8(Mg_0.6Zn_0.4)_0.95Co_0.05TiO₃–0.2Ca_0.61Nd_0.26TiO₃ possesses the excellent dielectric properties of a dielectric constant of 28.6, a Q × f value of 80,600 GHz and a temperature coefficient of resonant frequency of 4.1 ppm/°C and has a lower sintering temperature of 1250 °C.     

Studies on structural and electrical properties of Co1−xNixFe1.9Mn0.1O4 ferrite

Nickel-doped iron-deficient cobalt ferrite with small amount of manganese having the chemical composition Co_1−xNi_xFe_1.9Mn_0.1O₄, with x = 0.2, 0.4, 0.6 and 0.8, were prepared by standard double sintering ceramic method. The spinel phase formation was confirmed by X-ray diffraction (XRD). The DC resistivity measurements with temperature indicate a semiconducting behavior showing a linear decrease with increasing temperature and the doping of Ni enhances the resistivity. Maximum resistivity of the order of 10⁹ Ω cm was found for composition x = 0.8. Room temperature dielectric constant measurements with frequency (100 Hz to 1 MHz), show usual dielectric dispersion. Also, the variation of room temperature AC conductivity as a function of frequency were studied and explained by using Maxwell–Wagner two-layer model. The studies on dielectric constant (′), loss tangent (tan δ) and AC conductivity (σ_AC), at four different frequencies (viz., 1, 10, 100 kHz and 1 MHz), with temperature were made.     

Densification, microstructural evolution, and dielectric properties of hexagonal Ba(Ti1−xMnx)O3 ceramics sintered with fluxes

Recently, doped hexagonal BaTiO₃ (6h-BaTiO₃) ceramics have been reported as potential candidates used in microwave dielectric resonators. However, similar to other common microwave ceramics, doped 6h-BaTiO₃ ceramics require a high sintering temperature, greater than 1300 °C. In this study, the effect of sintering aids, including Bi₂O₃, B₂O₃, BaSiO₃, Li₂CO₃, CuO, V₂O₅, 5ZnO·2B₂O₃, and 5ZnO·2SiO₂, on the densification, microstructural evolution, and microwave properties of the 6h-Ba(Ti_0.85Mn_0.15)O₃ ceramics was examined. Results indicate that among the fluxes studied, Bi₂O₃, B₂O₃, and Li₂CO₃ could effectively reduce the sintering temperature of 6h-Ba(Ti_0.85Mn_0.15)O₃ ceramics through liquid phase sintering, while retaining the hexagonal structure and the microwave dielectric properties. The best results were obtained for the 6h-Ba(Ti_0.85Mn_0.15)O₃ with the additions of 5 wt% Bi₂O₃ sintered at 900 °C (_r: 54.7, Qf_r: 1323, and τ_f:183.3 ppm/°C), 10 wt% B₂O₃ sintered at 1100 °C (_r: 54.4, Qf_r: 3448, and τ_f: 254.5 ppm/°C), and 5 wt% Li₂CO₃ sintered at 950 °C (_r: 43.7, Qf_r: 2501, and τ_f: −29.8 ppm/°C).     

Role of titanium valence states in optical and electronic features of PbO–Sb2O3–B2O3:TiO2 glass alloys

PbO–Sb₂O₃–B₂O₃ glasses mixed with different concentrations of TiO₂ (ranging from 0 to 1.5 mol.%) were synthesized. The samples are characterized by X-ray diffraction, scanning electron microscopy and DSC techniques. A variety of properties, i.e. optical absorption, photoluminescence, infrared, ESR spectra, magnetic susceptibility, photo-induced birefringence (PIB) and dielectric properties (constant ′, loss tan δ, a.c. conductivity σ_ac over a wide range of frequency and temperature) of these glass–ceramics have been explored. The analysis of these results indicated that Ti ion surrounding ligands play principal role in the observed PIB and the sample crystallized with 0.8 mol.% of TiO₂ is the most suitable for the applications in non-linear optical devices.     

Monoclinic phases and stress-relief conditions in (1 − x)Pb(Mg1/3Nb2/3)TiO3–xPbTiO3 solid solutions

A comparative study on heterophase states in perovskite-type solid solutions of (1 − x)Pb(Mg_1/3Nb_2/3)TiO₃–xPbTiO₃ is carried out for compositions near the morphotropic phase boundary. The conditions for mechanical stress relief at elastic matching of phases are analysed at x = const in a wide temperature range. The heterophase states concerned with the presence of the intermediate monoclinic phase are interpreted using the domain state–interface diagrams calculated for x = 0.28, 0.32 and 0.34. It is shown that optimum volume fraction parameters of the domains in the monoclinic phase of the B type are varied in relatively wide ranges and promote complete stress relief with cubic–monoclinic phase coexistence. Two scenarios of stress relief at x = 0.32 are considered in connection with different heterophase states (either tetragonal–monoclinic of the B type or tetragonal–monoclinic of the C type) in a wide temperature range. Possibilities of elastic matching of two polydomain phases (tetragonal–monoclinic of the B type) with almost equal relative widths of the domains in these phases are shown for x = 0.34. The active role of domains of the monoclinic phases in stress relief and forming the planar unstrained interfaces is discussed.     

Characterization of sol-gel synthesised lead-free (1 − x)Na0.5Bi0.5TiO3-xBaTiO3-based ceramics

The crystal structure, microstructure, dielectric and ferroelectric properties of (1 − x)Na_0.5Bi_0.5TiO₃-xBaTiO₃ ceramics with x = 0, 0.03, 0.05, 0.07 and 0.1 are investigated. A structural variation according to the system composition was investigated by X-ray diffraction (XRD) analyses. The results revealed that the synthesis temperature for pure perovskite phase powder prepared by the present sol-gel process is much lower (800 °C), and a rhombohedral-tetragonal morphotropic phase boundary (MPB) is found for x = 0.07 composition which showing the highest remanent polarization value and the smallest coercive field. The optimum dielectric and piezoelectric properties were found with the 0.93Na_0.5Bi_0.5TiO₃-0.07BaTiO₃ composition. The piezoelectric constant d₃₃ is 120 pC/N and good polarization behaviour was observed with remanent polarization (P_r) of 12.18 pC/cm², coercive field (E_c) of 2.11 kV/mm, and enhanced dielectric properties ?_r > 1500 at room temperature. The 0.93Na_0.5Bi_0.5TiO₃-0.07BaTiO₃-based ceramic is a promising lead-free piezoelectric candidate for applications in different devices.     

Low temperature sintering and properties of CaO–B2O3–SiO2 system glass ceramics for LTCC applications

The P₂O₅ + ZnO, ZrO₂ + TiO₂, B₂O₃ and a low-melting-point CaO–B₂O₃–SiO₂ glass (LG) are selected as the sintering additives, and the effect of their additions on the microwave dielectric properties, mechanical properties and microstructures of CaO–B₂O₃–SiO₂ system glass ceramics is investigated. It is found that the sintering temperature of pure CBS glass is higher than 950 °C and the sintering range is about 10 °C. With the above additions, the glass ceramics can be sintered between 820 °C and 900 °C. The dielectric properties of the samples are dependent on the additions, densification and microstructures of sintered bodies. The major phases of this material are CaSiO₃, CaB₂O₄ and SiO₂. With 10 wt% B₂O₃ and LG glass additions, the CBS glass ceramics have better mechanical properties, but worse dielectric properties. The _r values of 6.51 and 7.07, the tan δ values of 0.0029 and 0.0019 at 10 GHz, are obtained for the CBS glass ceramics sintered at 860 °C with 2 wt% P₂O₅ + 2 wt% ZnO and 2 wt% ZrO₂ + 2 wt% TiO₂ additions, respectively. This material is suitable to be used as the LTCC material for the application in wireless communications.     

Dielectric and magnetic properties of 0.7Bi(Fe1−xCrx)O3–0.1BaTiO3–0.2PbTiO3 solid solutions

0.7Bi(Fe_1−xCr_x)O₃–0.1BaTiO₃–0.2PbTiO₃ (x = 0, 0.1, 0.2, 0.3) solid solutions were prepared by the traditional ceramic process. X-ray diffraction results revealed that the samples with x = 0–0.3 showed pure perovskite structure. Frequency and temperature dependences of dielectric constants and dielectric loss of the samples were investigated. Both dielectric constant and the loss tangent increased at given frequencies (100 Hz–1 MHz), while the Curie temperature of the solid solutions decreased with increasing Cr content. Room temperature magnetic hysteresis loops indicated that an appropriate amount of Cr could improve magnetization of the solid solutions.     

Microstructure, ferroelectric, and piezoelectric properties of (1 − x − y)Bi0.5Na0.5TiO3-xBaTiO3-yBi0.5Ag0.5TiO3 lead-free ceramics

Lead-free (1 − x − y)Bi_0.5Na_0.5TiO₃-xBaTiO₃-yBi_0.5Ag_0.5TiO₃ (BNT-BT-BAT-x/y, x = 0-0.10, y = 0-0.075) piezoelectric ceramics were synthesized by conventional oxide-mixed method. The microstructure, ferroelectric, and piezoelectric properties of the ceramics were investigated. Results show that a morphotropic phase boundary (MPB) between rhombohedral and tetragonal phases of BNT-BT-BAT-x/0.04 ceramics is formed at x = 0.06-0.08. The addition of BAT has no obvious change on the crystal structure of BNT-BT ceramics while it causes the grain size of the ceramics to become more homogenous. Near the MPB, the ceramics with x = 0.06 and y = 0.05-0.06 possess optimum electrical properties: P_r ∼ 42.5 μC/cm², E_c ∼ 32.0 kV/cm, d₃₃ ∼ 172 pC/N, k_p ∼ 32.6%, and k_t ∼ 52.6%. The temperature dependences of k_p and polarization versus electric hysteresis loops reveal that the depolarization temperature (T_d) of BNT-BT-BAT-0.06/y ceramics decreases with increasing y. In addition, the polar and non-polar phases may coexist in the BNT-BT-BAT-x/y ceramics above T_d.     

Properties of praseodymium-doped bismuth potassium titanate (Bi0.5K0.5TiO3) synthesised using the soft combustion technique

Bismuth potassium titanate (Bi_0.5K_0.5TiO₃; BKT) and praseodymium-doped BKT (Bi_0.5(1−x)Pr_xK_0.5TiO₃; BPKT) powders were synthesised using the soft combustion technique. Fine particles of 10-100 nm of BKT and BPKT were produced. A single phase BKT was obtained with a minimum of 0.5 mol of glycine. Various compounds of Bi_0.5(1−x)Pr_xK_0.5TiO₃ where x = 0.01, 0.03, 0.05, 0.10, 0.15 and 0.20 were prepared. Pure BKT and BPKT powders were obtained after calcination at 800 °C for 3 h. After sintering at 1050 °C for 5 h, pure BKT and BPKT pellets were obtained for x = 0 and 0.01. However, for BPKT with x = 0.03, 0.05, 0.10, 0.15 and 0.20, a minor amount of Bi₄Ti₃O₁₂ (BIT) secondary phase was present after sintering at 1050 °C for 5 h. The crystallite size and grain size of all the samples followed similar trends, first increasing from x = 0 (undoped BKT) to x = 0.05 and then decreasing above x = 0.05. Among the undoped and doped samples, BPKT with x = 0.05 had the highest dielectric properties (?_r = 713.87) due to its large crystallite size (68.66 nm), large grain size (∼435 nm) and high relative density (93.39%).     

The infrared absorption and dielectric properties of Li–Ga ferrite

The investigated compositions of the Li–Ga ferrite system Li_0.5Fe_2.5−xGa_xO₄ (where x = 0.0, 0.1, 0.2, 0.3, 0.4 and 0.5) were studied by means of infrared (IR) spectroscopy. The analysis of IR spectra indicates the presence of splitting in the absorption band due to the presence of Fe²⁺ ions in ferrite. The dielectric constant ′, the dielectric loss ″ and the loss tangent tan δ were measured at elevated temperatures ranging from room temperature up to 850 K as a function of frequency (f = 10²–10⁶ Hz) for the investigated compositions. Maximum peak in tan δ and inverse peaks in ′ appeared for some samples due to the resonance phenomenon. The obtained data were discussed based on the valence exchange between (Fe³⁺ and Fe²⁺) and (Ga³⁺ and Ga²⁺), i.e. hopping mechanism.     

Structural, magnetic and electrical properties of (La0.70−xNdx)Sr0.30Mn0.70Cr0.30O3 with 0 ≤ x ≤ 0.30

The structural, magnetic and electrical properties of (La_0.70−xNd_x)Sr_0.30Mn_0.70Cr_0.30O₃ perovskites (0 ≤ x ≤ 0.30) prepared by the usual ceramic procedure were investigated. Structural Rietveld refinement revealed that these compounds crystallize in a rhombohedral perovskite structure when x = 0, 0.10 and 0.20, while for x = 0.30 the structure becomes orthorhombic (Pbnm). It was found that the substitution of La by Nd reduces the Curie temperature (T_C). The FC, ZFC, M(H) and AC susceptibility measurements show typical canted-antiferromagnetism for the Nd-doped samples, in which a ferromagnetic component coexists with predominant antiferromagnetic interactions. The values of the magnetization (M(H)) decrease very slightly when increasing the Nd content, compared to the undoped sample (M_S values at 5 T and 2 K are, respectively, 47.9, 47.3 and 47.5 emu/g for x = 0.10, 0.20 and 0.30, compared to 48.2 emu/g for x = 0), indicating that the Nd³⁺ contribution is negligible compared to the total moment of the ferromagnetic (Mn/Cr) network. The resistivity increases by several orders of magnitude with Nd-doping and the semi-conducting behaviour persists in the whole temperature range. The interaction between Mn⁴⁺–O–Cr³⁺and Cr³⁺–O–Cr³⁺ is responsible for the semi-conducting state.     

The structural and electric properties of Li- and K-substituted Bi0.5Na0.5TiO3 ferroelectric ceramics

The structure, dielectric properties and phase transition of lithium and potassium modified Bi_0.5Na_0.5TiO₃ ceramics were investigated widely. The phase transition behavior with respect to changes in composition and temperature was investigated using X-ray diffraction analysis, dielectric and ferroelectric characterizations. The experimental results show that there is a diffusion phase transition in (Na_1−xK_x)_0.5Bi_0.5TiO₃ ceramics at T_m and the diffuseness of the phase transition is more obvious for the samples near the morphotropic phase boundary. In (Na_1−xLi_x)_0.5Bi_0.5TiO₃ system, due to the space charge polarization induced by ions conductivity, the low frequency permittivity increases so remarkably at high temperature that the peak of maximum permittivity vanishes. The hysteresis loops at different temperatures indicate that there is no existence of anti-ferroelectrics in lithium and potassium modified Bi_0.5Na_0.5TiO₃ ceramics above the depolarization temperature T_d. The depolarization reason is that the tetragonal nonpolar phase occurs and leads to the macro-micro domain transformation at about T_d.     

Dielectric dispersion in Li2O–MoO3–B2O3 glass system doped with V2O5

Li₂O–MoO₃–B₂O₃ glasses containing different amounts of V₂O₅, ranging from 0 to 1.5 mol%, were prepared. The dielectric properties (viz., constant ′, loss tan δ, AC conductivity σ_ac over a wide range of frequency and temperature) have been studied as a function of the concentration of vanadium ions. The variation of AC conductivity with the concentration of V₂O₅ passes through a maximum at 0.8 mol% V₂O₅. In the high-temperature region, the AC conduction seems to be connected with the mixed conduction, viz., electronic and ionic conduction. The dielectric relaxation effects exhibited by these glasses have been analyzed quantitatively by pseudo Cole–Cole plot method and the spreading of relaxation times has been established. Further analysis of these results has been carried out with the aid of the data on ESR, IR and optical absorption spectra.     

Investigation of the microwave dielectric properties of Ca1−xMgxLa4Ti5O17 ceramics for application in coplanar patch antenna

In this paper, the dielectric properties of Ca_1−xMg_xLa₄Ti₅O₁₇ ceramics at microwave frequency have been studied. The diffraction peaks of Ca_(1−x)Mg_xLa₄Ti₅O₁₇ ceramics nearly unchanged with x increasing from 0 to 0.03. Similar X-ray diffraction peaks of Ca_0.99Mg_0.01La₄Ti₅O₁₇ ceramic were observed at different sintering temperatures. A maximum density of 5.3 g/cm³ can be obtained for Ca_0.99Mg_0.01La₄Ti₅O₁₇ ceramic sintered at 1500 °C for 4 h. A maximum dielectric constant (_r) and quality factor (Q × f) of Ca_0.99Mg_0.01La₄Ti₅O₁₇ ceramic sintered at 1500 °C for 4 h are 56.3 and 12,300 GHz (at 6.4 GHz), respectively. A near-zero temperature coefficient of resonant frequency (τ_f) of −9.6 ppm/°C can be obtained for Ca_0.99Mg_0.01La₄Ti₅O₁₇ ceramic sintered at 1500 °C for 4 h. The measurement results for the aperture-coupled coplanar patch antenna at 2.5 GHz are presented. With this technique, a 3.33% bandwidth (return loss <−10 dB) with a center frequency at approximately 2.5 GHz has been successfully achieved.     

Magnetic ordering and magnetic properties of ErAuxNi1−xIn (0 ≤ x ≤ 1) solid solution

The ErAu_xNi_1−xIn (0 ≤ x ≤ 1) quasiternary compounds crystallize in the hexagonal layered crystal structure of ZrNiAl-type. ErAuIn was reported to be an antiferromagnet with T_N = 3 K and magnetic moments having triangular arrangement within the basal plane (the magnetic order is described by the propagation vector ). On the contrary ErNiIn is a ferromagnet with T_C = 9 K and magnetic moments pointing along the c-axis. The magnetic ordering in ErAu_xNi_1−xIn (0 < x < 1) solid solution, has been investigated by neutron diffractometry in the temperature range between 1.5 and 15 K. Moreover, bulk magnetic measurements have been carried out in the range 1.72–400 K. All alloys of intermediate composition were found to be antiferromagnets with T_N between 4.6 and 7 K. Below 2 K their magnetic order is described by the propagation vector and magnetic moments are aligned along the c-axis. However, for alloys with 0.2 ≤ x ≤ 0.7 the propagation vector was found to turn into with increasing temperature.     

Crystal structure and microwave dielectric properties of a new A4B3O12-type cation-deficient perovskite Ba3LaTa3O12

A new microwave dielectric ceramic Ba₃LaTa₃O₁₂ has been prepared by conventional solid-state ceramic route. Through Rietveld refinement of X-ray powder diffraction data, the compound is identified as an A₄B₃O₁₂-type B-site cation-deficient perovskite with space group and lattice constants a = 5.7573(2) Å, c = 28.2386(2) Å, V = 810.62(4) Å³ and Z = 3. The microwave dielectric properties of Ba₃LaTa₃O₁₂ were investigated. The compound exhibits a relative dielectric constant (_r) of 36.8, a quality factor Q_u × f of 21,965 at 6.4040 GHz and a small negative temperature coefficient of resonant frequency (τ_f) of −49.6 ppm/°C.     

Effect of potassium doping on the structural, magnetic and magnetocaloric properties of La0.7Sr0.3−xKxMnO3 perovskite manganites

We investigate the effect of potassium doping on the structural, magnetic and magnetocaloric properties of La_0.7Sr_0.3−xK_xMnO₃ (x = 0.05, 0.1, 0.15 and 0.2) powder samples. Our polycrystalline compounds were synthesized using the solid-state reaction at high temperature. X-ray diffraction characterizations showed that all our studied samples crystallize in the distorted rhombohedral system with space group. With increasing potassium content, the unit cell volume exhibits a broad maximum around x = 0.15. Magnetization measurements versus temperature showed that all our samples exhibit a paramagnetic to ferromagnetic transition with decreasing temperature. The Curie temperature T_C is found to decrease from 365 K for x = 0 to 328 K for x = 0.2 as well as the saturated magnetization M_sp which shifts from 3.68 μ_B/Mn for x = 0 to 3.05 μ_B/Mn for x = 0.2. The critical exponent γ defined as M_sp (T) = M_sp(0)[1−(T/T_C)]^γ is found to remain almost constant and equal to 0.33 for all our samples. The maximum of magnetic entropy changes |ΔS_max| of La_0.7Sr_0.3−xK_xMnO₃ for x = 0.05 and 0.15 is found to be respectively, 1.37 and 1.2 J kg⁻¹ K⁻¹ under a magnetic field change of 1 T.     

Thermoelectric properties of Sn1−x−yTiySbxO2 ceramics

Thermoelectric properties of Sn_1−x−yTi_y Sb_xO₂ ceramics were investigated in detail. The addition of Sb into SnO₂ matrix increased the electric conductivity, σ. The increase in the σ value should be caused by the increase in the carrier concentration. The Seebeck coefficients of all the samples were negative, which means that these samples have n-type conduction. The samples of this study have porous structure. The maximum Z value of all the samples measured in this study was 2.4 × 10⁻⁵ K⁻¹.