Synthesis,characterisation and solution thermal behaviour of a family of poly (N-isopropyl acrylamide-co-N-hydroxymethyl acrylamide) copolymers

Thermo-responsive copolymers of poly (N-isopropyl acrylamide-co-N-hydroxymethyl acrylamide)p(NIPAAm-co-HMAAm) with a range of content of hydroxy groups have been synthesised by free radical polymerisation. The polymers were characterised by NMR, FTIR and GPC. A detailed study of the solution thermal properties showed that polymers with up to about 50 wt.% hydroxy monomer show lower critical solution temperature (LCST) properties in water. Polymers with higher hydroxy monomer content are fully soluble at all temperatures up to 100 °C. The effect of pH, salts and solvent additives on the solution thermal behaviour of the copolymers was investigated, showing that “salting-out” salts lowered the LCST and “salting-in” salts caused an initial increase in LCST at low concentrations, but reduced LCST at higher concentrations, in line with the Hoffmeister series. The LCST of any copolymer composition from this family in pure water can be predicted from the empirical equation; LCST = 0.015x² + 0.25x + 31.76, where x is the fraction of the hydroxy monomer. Due to differences in polarity and the length of the carbon chain, methanol and ethanol altered LCST of p(NIPAAm) and its hydroxyl copolymers in different manners, showing a transition from cononsolvency to cosolvency as the hydroxyl content of the copolymer increased. A more complex polyhydroxy compound, sucrose, had very little effect on LCST for either p(NIPAAm) or its hydroxyl copolymers.     

Hydrogen-bond-assisted stereocontrol in the radical polymerization of N-isopropylacrylamide with bidentate Lewis base

Radical polymerization of N-isopropylacrylamide (NIPAAm) in toluene was investigated in the presence of bidentate Lewis base such as diphosphonates. Isotacticity of the obtained poly(NIPAAm)s slightly increased at −80 °C, whereas syndiotactic-rich poly(NIPAAm)s were obtained at −40-0 °C. This result corresponded to the results observed in the presence of primary alkyl phosphates. NMR analysis revealed that NIPAAm monomer and tetraisopropyl methylenebisphosphonate formed mono-binding hydrogen-bond-assisted complex at 0 °C, but a chelate complex at −80 °C. Thus, it was concluded that the stereospecificity in NIPAAm polymerization strongly depended on the complexation mode of the added bidentate Lewis base.     

The effects of charge densities on the associative properties of a pH-responsive hydrophobically modified sulfobetaine/sulfur dioxide terpolymer

Sulfur dioxide, zwitterionic monomer, 3-(N,N-diallylammonio)propanesulfonate and a hydrophobic monomer N,N-diallyl-N-octadecylammonium chloride were cycloterpolymerized in dimethyl sulfoxide using azobisisobutyronitrile (AIBN) as the initiator to afford water-insoluble polysulfobetaines (PSB) in excellent yields. The PSBs were converted into the corresponding anionic polyelectrolyte (APE) by treatment with 1 equiv. of sodium hydroxide. Treating the pH-responsive PSB polymers with different equivalents of NaOH varied the zwitterionic and anionic charge densities in the polymer chain. The polymer chains with zwitterionic fraction greater than 0.5 were found to be insoluble in water. The solution properties of the APE and PSB/APE systems containing varying amount of the hydrophobic monomers in the range 0-10 mol% were investigated by viscometric techniques. It was found that PSB/APE polymer with a ratio of 33:67 for the zwitterionic and anionic fractions in the polymer chains, respectively, gave the highest viscosity value. The polymer concentration (C*_HA) of around 1 g/dl was required for the manifestation of significant hydrophobic associations. The polymer solutions exhibited sharp increase in viscosity with increasing polymer concentrations in salt (NaCl)-free as well as salt-added solutions. The presence of sodium chloride is shown to enhance intermolecular associations in polymers having hydrophobes in the lower mol% range, whereas, intramolecular associations were manifested in polymers containing higher proportions of the hydrophobes.     

Effect of polymerization conditions on the syndiotactic-specificity in radical polymerization of N-isopropylacrylamide and fractionation of the obtained polymer according to the stereoregularity

Radical polymerization of N-isopropylacrylamide (NIPAAm) was examined in the presence of hexamethylphosphoramide (HMPA). The addition of an excess amount of HMPA induced syndiotactic-specificity that gradually enhanced as the feed monomer was consumed. The syndiotacticity of the obtained poly(NIPAAm)s was improved by increasing the [HMPA]₀/[NIPAAm]₀ ratio to five and prolonging the polymerization time to 96 h (racemo=72%). It was also revealed that more stereoregulated poly(NIPAAm) could be fractionated by reprecipitating the resulting polymers from hexane-THF mixture. This result suggested that more stereoregulated poly(NIPAAm) showed a lower solubility than less stereoregulated poly(NIPAAm)s. Furthermore, unusual hysteresis was observed in transmittance analysis of an aqueous solution of the fractionated syndiotactic poly(NIPAAm).     

Reversible addition-fragmentation chain transfer polymerization of 7-(4-(acryloyloxy)butoxy)coumarin

The light sensitive vinyl monomer with coumarin unit, 7-(4-(acryloyloxy)butoxy)coumarin (7AC), was synthesized. The reversible addition-fragmentation chain transfer (RAFT) polymerization of 7AC, initiated by 2,2′-azobisisobutyronitrile (AIBN), was carried out using 2-cyanoprop-2-yl dithiobenzoate (CPDB) as a RAFT agent in N,N-dimethylformamide (DMF) solution. The kinetics exhibited first-order relationship with respect to the monomer concentration. The molecular weight of the polymer increased linearly with the monomer conversion. The chain extension of poly(7-(4-(acryloyloxy)butoxy)coumarin) (P7AC) using styrene (St) as the second monomer demonstrated that the obtained polymers were almost “living”. The fluorescence intensity of P7AC increased with the molecular weight of P7AC and was stronger than that of the monomer. The obtained polymer had strong ultraviolet (UV) absorption at 322 nm. The molecular weights of the polymer had no effect on its ultraviolet absorption intensity. The coumarin structure existing in P7AC underwent [2 + 2] cycloaddition reaction (photodimerization) under UV irradiation in tetrahydrofuran (THF) solution, which can be further used to prepare small particles from the single polymer.     

Gel polymer electrolyte based on poly(acrylonitrile-co-styrene) and a novel organic iodide salt for quasi-solid state dye-sensitized solar cell

A gel polymer electrolyte based on poly(acrylonitrile-co-styrene) as polymer matrix and N-methyl pyridine iodide salt as I⁻ source was prepared. Controlling the concentration of polymer matrix of poly(acrylonitrile-co-styrene) at 17.5 wt.%, mixing the binary organic solvents mixture ethylene carbonate and propylene carbonate with 6:4 (w/w), and the concentration of N-methyl pyridine iodide and iodine with 0.5 and 0.05 M, respectively, the gel polymer electrolyte attains the maximum ionic conductivity (at 30 °C) of 4.63 mS cm⁻¹. Based on the gel polymer electrolyte, a quasi-solid state dye-sensitized solar cell was fabricated and its overall energy conversion efficiency of light-to-electricity of 3.10% was achieved under irradiation of 100 mW cm⁻².     

A facile preparation of highly interconnected macroporous poly(d,l-lactic acid-co-glycolic acid) (PLGA) scaffolds by liquid-liquid phase separation of a PLGA-dioxane-water ternary system

Regular and highly interconnected macroporous scaffolds ranging in size from 50 to 150 μm were fabricated from poly(d,l-lactic acid-co-glycolic acid) (PLGA)-dioxane-water ternary systems via thermally induced phase separation (TIPS) without any surfactant or other additives. The effect on scaffold morphology of processing parameters including quenching temperature, polymer concentration, solvent composition and molecular weight, was investigated as a function of quenching time. The cloud-point temperature of the polymer solution was found to depend on polymer concentration, solvent composition, and polymer molecular weight. The water content in the solvent mixture had the greatest effect on the cloud-point temperature. The optimal quenching temperature for preparing macroporous inter-connected scaffolds from a 9 wt% PLGA solution (dioxane-water=87/13, by wt) was less than −7 °C. In low viscosity PLGA solutions, sedimentation of the polymer rich phase occurred due to the segregation of the separated phases under gravity. This led to the formation of scaffolds with irregular and closed pores.     

Thermoreversible hydrogels VI: Swelling behavior of the (N-isopropylacrylamide-co-diethyl methyl methacryloyloxyethyl ammonium iodide) copolymeric hydrogels in aqueous salt solutions

A series of N-isopropylacrylamide/diethyl methyl methacryloyloxyethyl ammonium iodide (NIPAAm/DEMMAI) copolymeric gels were prepared from blending NIPAAm, cationic monomer DEMMAI, and N,N′-methylene bisacrylamide (NMBA) in various molar ratios in this article. The effects of the amount of the cationic monomer in the copolymeric gels on the swelling behaviors in water and various saline solutions at various temperatures were investigated. Results showed that the swelling ratios of copolymeric gels were significantly larger than those of pure NIPAAm gel, and that the more the DEMMAI content, the higher the gel transition temperature. In the saline solution, results showed that the swelling ratio for pure NIPAAm gel had not changed significantly with an increase of the salt concentration until the salt concentration was larger than 0.1 M. The swelling ratios for the copolymeric gels NIPAAm/DEMMAI were decreased with increasing salt concentration. In various saline solutions, results showed that the anionic effects were greater than cationic effects in the presence of common anion with different cations and common cation with different anions for these hydrogels. Finally, we also tested the reversibility of the NIPAAm/DEMMAI copolymeric gels. The deswelling and reswelling kinetics were dependent on the temperature which was below or above the gel transition temperature. The gel with a small DEMMAI content has a good reversibility.     

High glass transition and thermal stability of new pyridine-containing polyimides: Effect of protonation on fluorescence

A new diamine monomer containing heterocyclic pyridine and triphenylamine groups, 4-(4,4′-diaminotriphenylamine)-2,6-bis(4-methylphenyl)pyridine (4), was synthesized by Chichibabin and nucleophilic fluoro-displacement reactions. The diamine was used to prepare a series of novel polyimides via polycondensation with various aromatic tetracarboxylic dianhydrides in N-methyl-2-pyrrolidinone. The polyimide 4a derived from the diamine 4 with 4,4′-hexafluoroisopropylidenediphthalic anhydride and having high T_g (313 °C), mechanical, and thermal properties was soluble in various organic solvents, such as N-methyl-2-pyrrolidinone, N,N-dimethylacetamide, N,N-dimethylformamide, pyridine, chloroform, tetrahydrofuran, at room temperature. The polyimide (4a) could be cast into a self-standing film from DMAc solution and was thermally converted into tough and flexible film. The film had high tensile modulus of 2.2 GPa and exhibited excellent thermal stability in both nitrogen and air (T_d¹⁰ > 550 °C). The pristine polymer exhibited the UV-vis absorption bands in the region 240-400 nm and protonated polymer exhibited absorption in the region 390-500 nm. The protonated polymer possessed strong orange fluorescence (around 600 nm) in THF solution after protonation with acids as excited at 438 nm. The fluorescent intensity was influenced by the acid concentrations and the chemical structure of conjugated bases. The fluorescent intensity at 600 nm increased as acid concentration from a lower to a moderate concentration and decreased at higher concentrations.     

Delaying the onset of macrogelation for the synthesis of branched and star-like polymers via conventional free-radical polymerisation: Binary solvent effects and incorporation of surfmers

It is known that the preferential solvation and conformation of a polymer in a solvent mixture are functions of the polymer's molecular weight and the solvent qualities. This paper demonstrates that these relationships can be exploited to delay the onset of macrogelation for branched poly(methyl methacrylate/ethylene glycol dimethacrylate) (p(MMA/EGDMA)) polymers and star-like poly(methyl acrylate/ethylene glycol dimethacrylate) (p(MA/EGDMA)) polymers synthesised via conventional free-radical polymerisation (CFRP) in a binary solvent mixture (consisting of a good solvent and a precipitant for the polymer). The gelation limits of the MMA/EGDMA and MA/EGDMA polymerisations in a methyl ethyl ketone (MEK)/heptane binary solvent mixture can be extended to regions of higher monomer concentration with increases in polymer yield between 13 and 50 ± 5 w/w% for the p(MMA/EGDMA) system and between 8 and 19 ± 6 w/w% for the p(MA/EGDMA) system across the gelation boundary. Thus, a facile method of increasing the concentration of batch reaction mixtures by the simple addition of small amounts of precipitant into the reaction solutions is presented. Furthermore, the gelation limits of both polymerisation systems in the binary solvent mixtures were further extended with increases in polymer yield between 11 and 17 ± 4%w/w for the p(MMA/ODA/EGDMA) system and between 8 and 20 ± 5%w/w for the p(MA/VS/EGDMA) system by the respective incorporation of octadecyl acrylate (ODA) and vinyl stearate (VS) surfmers into the polymers, demonstrating the application of steric hinderance to shield the propagating polymers from excessive cross-linking reactions.     

Effect of monomer content on physical properties of silicon nitride ceramic green body prepared by gelcasting

The gelcasting technique was employed to prepare Si₃N₄ green body. The monomers used in the research were acrylamide (AM) and N,N′-methylenebisacrylamide (MBAM). The influences of the monomer content (AM and MBAM) and the ratio of monomers (AM/MBAM) on the warpage rate, shrinkage rate, and the flexural strength of Si₃N₄ ceramics green body were investigated. Both warpage rate and shrinkage rate of green body were found to decrease with the increase of monomer content, and monotonically increase with the ratio of monomers after drying. The variation of warpage rate with the ratio of monomers is evident when monomer content is 20 wt.%, but the variations are not evident when monomer contents are 40 and 55 wt.%. The flexural strength of the green body is highest at an optimum value of the monomers ratio, and increases with increasing monomer content, reaching 50–90 MPa when monomer contents are 40 and 55 wt.%.     

Micro-flowers of poly(p-phenylene pyromelliteimide) crystals

Morphology control of poly(p-phenylene pyromelliteimide) (PPPI) crystals was examined using reaction-induced crystallization of oligomers during solution polymerization of self-polymerizable N-(4′-aminophenyl)-3-carboxyl-4-alkoxycarbonylphthalimide. Micro-flowers of the PPPI needle-like crystals were formed in which the needle-like crystals grew radially from the center part as petals. The molecules aligned regularly along the long axis of the needle-like crystal. The structure of alkoxy group in the monomer and the monomer concentration influenced the size of the needle-like crystals, and their average length and width were changeable from 640 nm to 1.69 μm and from 110 nm to 210 nm, respectively. The average thickness was 20 nm. The obtained micro-flowers possessed high crystallinity and exhibited excellent thermal stability.     

Hydrogen-bond-assisted isotactic-specific radical polymerization of N-isopropylacrylamide with pyridine N-oxide

Radical polymerization of N-isopropylacrylamide (NIPAAm) in CHCl₃ at low temperatures in the presence of pyridine N-oxide (PNO) was investigated. An isotactic poly(NIPAAm) with meso diad content of 61% was successfully prepared at −60 °C in the presence of a two-fold amount of PNO. Thermodynamic analysis suggested that the isotactic-specificity was entropically induced, probably due to conformational fixation near the propagating chain-end through coordination by PNO.     

Use of exfoliated graphite filler to enhance polymer physical properties

Three sets of exfoliated graphite filled polymers, having three different particle sizes, were prepared with load levels from 0.1-20% by weight. After sieving, the particles were reduced to nanometer size through exfoliation, shear mixing, and ultrasonication, which further breaks and delaminates them. The electrical, thermal and mechanical properties of the nanoparticle filled polymers were measured. In addition, light, scanning electron, and atomic force microscope characterization were performed. The exfoliated graphite filled polymer material could be tailored to be high modulus and vary from insulating to highly conducting. Compared with the pure polymer, the polymers filled with 20% wt. exfoliated graphite has seen an significant reduction in electrical resistivity from 1.5⁸ to 0.5 Ω cm. The thermal conductivity for the polymers containing 20% wt exfoliated graphite has also been drastically improved, increasing from 0.2 to 5 W/m K. The flexural modulus achieved a maximum increase of 3.8 GPa which is a 60% above the value for the pure polymer (2.4 GPa).     

Thermoreversible hydrogel. V. Synthesis and swelling behavior of the N-isopropylacrylamide-co-trimethyl methacryloyloxyethyl ammonium iodide copolymeric hydrogels

A series of N-isopropylacrylamide/trimethyl methacryloyloxyethyl ammonium iodide (NIPAAm/TMMAI) copolymeric gels are prepared from the various molar ratios of NIPAAm, cationic monomer TMMAI, and N,N′-methylene bisacrylamide (NMBA) in this article. The influences of the amount of the cationic monomer in the copolymeric gels on the swelling behavior in water, various saline solutions, and various temperatures are investigated. Results show that the swelling ratios of copolymeric gels are significantly larger than those of pure homopolymer NIPAAm gel, and the more the TMMAI content, the higher the gel transition temperature. In the saline solution, results show that the swelling ratio of pure NIPAAm gel has not significantly changed with an increase of the salt concentration until the salt concentration is larger than 0.1M. The swelling ratios for the copolymeric gels NIPAAm/TMMAI decrease with increasing salt concentration. In various saline solutions, results show that the anionic effects are greater than cationic effects in the presence of common anion, different cations and common cation, and different anions for these hydrogels. Finally, we also tested the reversibility of the NIPAAm/TMMAI copolymeric gels. The deswelling and reswelling kinetics are dependent on the temperature, which is below or above the gel transition temperature. The gel with little TMMAI content has a good reversibility. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 1793–1803, 1998     

Anomalous crystallinity in a semi-fluorinated perfluorocyclobutyl (PFCB) polymer containing the hexafluoro-i-propylidene (6F) linkage

The thermal cyclopolymerization of 2,2-bis(4-trifluorovinyloxyphenyl)-1,1,1,3,3,3-hexafluoropropane affords the first example of a semi-crystalline perfluorocyclobutyl (PFCB) polymer and an anomalous feature for a polymer containing the hexafluoroisopropylidene (6F) linkage. Fluoroalkylation of 2,2-bis(hydroxyphenyl)-1,1,1,3,3,3-hexafluoropropane (6F bisphenol A) with 1,2-dibromotetrafluoroethane, followed by zinc mediated elimination affords the bis(trifluorovinyloxyphenyl) monomer in good yield. High molecular weight polymer (M_w=66,700) with molecular weight distribution approaching 2 was obtained by heating neat monomer at 180 °C for 24 h and 220 °C for 8 h. The stereo-random polymer (ca. 48 to 52 cis- to trans-1,2-disubstituted perfluorocyclobutyl groups) is easily crystallized from the melt despite the presence of the 6F group and a substantial increased fluorocarbon content per repeat unit compared to traditional PFCB polymers. A melting temperature approaching 200 °C was measured by DSC and the crystallinity was characterized by WAXD. Remarkably, the high melting semi-crystalline polymer could be easily dissolved in common solvents in greater than 50 wt% solutions.     

In situ UV-vis spectroelectrochemistry of poly(o-phenylenediamine-co-m-toluidine)

Results of in situ UV-vis spectroelectrochemical studies of the electropolymerization of o-phenylenediamine (OPD), m-toluidine (MT) and the copolymerization of OPD with MT are reported. Electropolymerization was performed in aqueous acidic medium at a constant potential of E_SCE = 1.0 V at an indium doped tin oxide (ITO) coated glass electrode. The course of homopolymerization was followed for MT and OPD solutions with various monomer concentrations. The spectral characteristics of the mixed solutions were studied at a constant concentration of MT and various concentrations of OPD in the comonomer feed. An absorption band at λ = 497 nm was assigned to the head-to-tail mixed dimer/oligomer resulting from the cross reaction between OPD and MT cation radicals. UV-vis spectra recorded during copolymerization show dependence of the growth of the band at λ = 497 nm on OPD concentration in the feed. At lower OPD feed concentration it appears as the major band in the corresponding spectra. The UV-vis spectra recorded for the copolymer films suggest the incorporation of both monomer units in the copolymer. The FT-IR spectra of the copolymers show the presence of phenazine type structures in the copolymer backbone.     

Fabrication and characterization of Matrimid/MIL-53 mixed matrix membrane for CO2/CH4 separation

In this study, gas separation properties of Matrimid/MIL-53 mixed matrix membranes with different MOF weight percentages (0–20 wt.%) were investigated. TEM, XRD and DLS analysis were implemented to investigate MIL-53, structure and particles size distribution. SEM, FTIR, DSC and TGA analyses were conducted to characterize the fabricated membranes. The SEM images of these membranes showed good adhesion between polymer and particles, although for 20% MIL-53 loading, particles agglomeration was observed in some areas. Moreover, surface images of the membranes showed adequate dispersion of the particles in the polymer matrix, especially at lower MOF loadings. The permeability of pure CO₂ and CH₄ gases for all membranes were measured and the ideal CO₂/CH₄ selectivity was calculated. CH₄ permeability of membranes increased slightly as the percentage of loading increased. At 20 wt.% MOF loading, void formation led to a significant increase in CH₄ permeability (300% over pure Matrimid). CO₂ permeability showed the same trend; there was a 94% increase in permeability compared to pure Matrimid for 15 wt.% MMMs. CO₂/CH₄ selectivity also increased as MOF loading increased. The highest selectivity was shown for 15 wt.% MOF loading. This membrane had 84% growth in selectivity over pure Matrimid. Although at 20 wt.% MIL-53 loading, membrane separation performance was destroyed.     

A study of hydrogel thermal-dynamics using Fourier transform infrared spectrometer

A rapid and reliable method was presented for studying hydrogel dynamics/kinetics. Two temperature-sensitive hydrogels, poly-N-isopropylacrylamide (poly(NIPAAm)) and the copolymer of N,N-diethylacrylamide and sodium methacrylate (molar ratio=97:3, poly(NDEAAm-co-MAA)) were synthesized. The thermal-behaviors of the gels were studied through the absorbance intensities of both swollen water and gel frame components, and the peak positions of amide band along heating/cooling pathways under dynamic Fourier transform infrared (FTIR) probing. The results showed that the lower critical solution temperature (LCST) of poly(NIPAAm) is about 33-35 °C, which is consistent with reported value of ∼34 °C. Compared to poly(NIPAAm), poly(NDEAAm-co-MAA) has relatively continuous volume phase transition, starting at ∼35 °C and a better thermal-reversibility with similar swelling and deswelling profiles over a larger temperature range (10-80 °C for poly(NDEAAm-co-MAA) vs. 10-33 °C for poly(NIPAAm)). The H-bonding water along phase transition was also studied, showing a less reversibility of poly(NIPAAm) compared to poly(NDEAAm-co-MAA). In addition, FTIR spectrometer was also used to study the volume changes of poly(NDEAAm-co-MAA) under variations in environmental salinity.     

Direct synthesis of syndiotactic-rich poly(N-isopropylacrylamide) via radical polymerization of hydrogen-bond-complexed monomer

Radical polymerization of N-isopropylacrylamide (NIPAAm) in toluene was investigated in the presence of hexamethylphosphoramide (HMPA). We succeeded in directly preparing syndiotactic-rich poly(NIPAAm), the syndiotacticity of which (r=70%) is the highest among those of radically-prepared poly(NIPAAm)s so far reported, by lowering polymerization temperature to −60 °C in the presence of a two-fold amount of HMPA. The NMR analysis revealed that the induced syndiotactic-specificity was ascribed to 1:1 complex formation between NIPAAm and HMPA. Furthermore, thermodynamic analysis described that the induced syndiotactic-specificity was enthalpically achieved.