Solution hardening of lead single crystals at liquid air temperature

Single crystals of lead with either thallium, indium, bismuth, cadmium, mercury or antimony were tested in tension in liquid air. The critical resolved shear stress ₀ increases linearly with increasing solute content c in a limited concentration range. The increase ₀/C is lowest for lead-thallium and highest for lead-antimony. When log ₀/C is plotted against log (sf + elf) where sf*[(d ₁)_Pb – (d ₁)_sol/(d ₁)_Pb]10^Pb, d ₁ being the closest distance of approach, and elf = En, En being the sum of the electronegativities of solvent and solute, a straight line of slope 2 results. A similar result is obtained with data from the literature for single crystals of copper alloys and of magnesium alloys. However in these cases a different size factor has to be used.     

Solid state phase transformation of BaB2O4 during the isothermal annealing process

Solid-state phase transformation of BaB₂O₄ during the isothermal annealing process for both to and to were investigated using a platinum crucible. For the -phase crystal at the -phase stable temperature (> 925 °C), the phase transforms to the phase perfectly below the melting temperature of 1100 °C. Meanwhile, for the -phase crystal at the -phase stable temperature (< 925 °C), the phase transforms to the phase perfectly above 800 °C. There is some difference in phase transformation behaviour between bulk-shape crystals and the powder, caused by thermal stress.     

On the measurement and physical meaning of the cleavage fracture stress in steel

Elastic-plastic two-dimensional (2D) and three-dimensional (3D) finite element models (FEM) are used to analyze the stress distributions ahead of notches of four-point bending (4PB) and three-point bending (3PB) specimens with various sizes of a C-Mn steel. By accurately measuring the location of the cleavage initiation sites, the local cleavage fracture stress _f and the macroscopic cleavage fracture stress _F is accurately measured. The _f and _F measured by 2D FEM are higher than that by 3D FEM. _f values are lower than the _F, and the _f values could be predicted by _f=(0.8––1.0)_F. With increasing specimen sizes (W,B and a) and specimen widths (B) and changing loading methods (4PB and 3PB), the fracture load P _f changes considerably, but the _F and _f remain nearly constant. The stable lower boundary _F and _f values could be obtained by using notched specimens with sizes larger than the Griffiths–Owen specimen. The local cleavage fracture stress _f could be accurately used in the analysis of fracture micromechanism, and to characterize intrinsic toughness of steel. The macroscopic cleavage fracture stress _F is suggested to be a potential engineering parameter which can be used to assess fracture toughness of steel and to design engineering structure.     

Negatively isotone optimal policies for random walk type Markov decision processes

Summary This paper considers a random walk type Markov decision process in which the state spaceI is an integer subset of IR ^m , and the action spaceK is independent ofi I. The natural order, overI, and a quasi order,, overK, is assumed, together with aconditional convexity assumption on the returns {r _i ^k }, and certain other assumptions about these rewards and the transition probabilities in relationship to the orders and.A negatively isotone policy is one for whichi i(i))(i) (i.e.(i) (i) or(i) i)). It is shown that, under specified conditions, a negatively isotone optimal policy exists. Some consideration is given to computational implications in particular relationship to Howard's policy space method.

---

Zusammenfassung Wir betrachten einen Markovschen Entscheidungsprozeß vom random walk Typ. Der ZustandsraumI sei eine Teilmenge des IR^m, wobeii I ganzzahlige Komponenten habe. Die MengeK der zulässigen Aktionen ini I sei unabhängig voni I. Sei die natürliche Ordnung aufI und sei eine Quasiordnung aufK. Die Erträge {r _i ^k }seienbedingt konvex, darüberhinaus seien weitere Voraussetzungen über diese Erträge und die Übergangswahrscheinlichkeiten in Bezug auf die Ordnungen und erfüllt. Eine Politik heißt negativ isoton, falls ausi i folgti(i) (d. h.(i) (i) oder(i)(i)). Wir zeigen, daß unter gewissen Voraussetzungen einenegativ isotone optimale Politik existiert: Auch diskutieren wir einige Folgerungen für die Numerik, insbesondere hinsichtlich Howards Politikiteration.

     

Die Herleitung von Schalengleichungen über ein erweitertes Variationsprinzip bei Berücksichtigung der Querschubverzerrungen

Ohne ZusammenfassungBezeichnungen L Bezugsgrößen für dimensionslose Koordinaten - L charakteristische Schalenabmessung - t Schalendicke - Schalenparameter - körperfeste, krummlinige, dimensionslose Koordinaten der Schalenmittelfläche - Dimensionslose Koordinate in Richtung der Schalennormalen - i, j,...=1,2,3 Indizierung des dreidimensionalen Euklidischen Raumes - ,,...=1,2 Indizierung des zweidimensionalen Riemannschen Raumes - (...), Partielle Differentiation nach der Koordinate - (...), Kovariante Differentiation für Tensorkomponenten des zweidimensionalen Raumes nach der Koordinate - (...)| Kovariante Differentiation für Tensorkomponenten des dreidimensionalen Raumes nach der Koordinate - Variationssymbol - a ,a ₃ Basisvektoren der Schalenmittelfläche - V Verschiebungsvektor - U ,U ₃ Verschiebungskomponenten des Schalenraumes - v ,w,w ,W Verschiebungskomponenten der Schalenmittelfläche - Verhältnis der Metriktensoren des Schalenraumes und der Schalenmittelfläche - _ik Verzerrungstensor des Raumes - _{(, )}, Symmetrische Verzerrungstensoren der Schalenmittelfläche - _{[, ]} Antimetrischer Term des Verzerrungsmaßes - ^, Spannungstensor - n ,m ,q Tensorkomponenten der Schnittgrößenvektoren - p ,p,c Tensorielle Lastkomponenten     

A mixed finite element formulation for shells through a reduced Reissner's principle in elastodynamics

Summary The use of Mixed models based in Reissner's principle in statics has been found to lead to some desirable simplifications in Finite Element formulations, in particular in plates and shells. Reduced formulations of Reissner's principle such as the one used by Prato have proved to be even more successful. In this paper, a reduction similar to that of Prato is attempted on a mixed elastodynamic variational principle by Karnopp.

---

Eine gemischte finite Elemente-Formulierung für Schalen durch ein reduziertes Reissnersches Prinzip der Elastodynamik

Zusammenfassung Die Verwendung von gemischten Modellen basiert auf Reissners Prinzip der Statik führt zu erwünschten Vereinfachungen bei der Formulierung von finiten Elementen im speziellen bei Untersuchungen von Platten und Schalen. Reduzierungen des Reissnerschen Prinzips, wie sie von Prato angewendet worden sind, haben sich sogar als noch erfolgreicher erwiesen. In dieser Untersuchung wird eine Reduktion, ähnlich der von Prato, für ein gemischtes elastodynamisches Variationsprinzip nach Karnopp, vorgenommen.

---

Symbol Table A Domain of integration of the Functional. Also area of the triangle - b Second fundamental form of the shell middle surface - C ^ijkl Elastic Constants - E ₁,E ₁ ^* Strain Energy and Co-Energy density - e _ij Elastic strain tensor - f _i Body force density tensor - I _ks Karnopp's functional, specialized to shells - I _ksc Contracted Karnopp's functional, specialized to shells - i, j, k Index 1, 2, 3 - K ₁,K ₁ ^* Kinetic Energy and Co-Energy density - K ^* Kinetic co-energy density for shell - m Moment tensor defined at the mid-surface - n In-plane stress tensor defined at the middle surface - n Qualifier for the boundary normal - p ,p ³ Boundary forces - Prescribed boundary forces - p Shear force tensor defined at the mid-surface - R Position vector of a point in the volume of the shell - r Position vector of a point on the mid-surface - r _i Net impulse density tensor - S _u Portion of the boundary where displacements are preseribed - S Portion of the boundary where forces are prescribed - s Qualifier for the direction tangent to the boundary - t Time variable - t ^ij Stress tensor - u ,u ₃ Mid-surface displacements - Mid-surface velocities - V Volume - v _i Displacement tensor - , Indices. Range 1, 2 - Shear strain tensor for the middle surface - Variation operator - Mid-surface strain tensor - Mid-surface curvature strain tensor - Direction cosine tensor for boundary normal - Mid-surface rotation tensor - Mid-surface angular velocity tensor - _M Strain energy density - _M * Strain co-energy density - _B * Bending strain co-energy density - _TS ^* Transverse shear strain co-energy density - | Covariant differentiation with respect tox , etc - Partial differentiation with respect tox , etc - .(dot) Time differentiation - -(bar) Prescribed quantities     

On a simple wave approximation of a set of linear dispersive wave equations

Summary The validity of an approximation ₀ of one of the solutions of a set of two linear coupled dispersive wave equations has been discussed. ₀ is the solution of a linear Korteweg-de Vries equation and satisfies the same initial condition as . It is shown that for square integrable solutions having a spectral range not exceeding [–, ] the approximation is useful if ^{5 2}t«1 in the sense that –₀(t)« (t)(L ₂ -norm). is a measure for the dispersion. The approximation fails in that sense ast . Some remarks to a similar nonlinear problem are made.     

Determination of the thermophysical characteristics of alternatively freezing and thawing dispersed media by the method of solving inverse problems of heat conduction

The article explains an algorithm for determining the thermophysical characteristics of dispersed media with phase transitions based on the method of solving inverse problems of heat conduction.Notation r space coordinate - time - T temperature of the specimen - T₀ initial temperature - c_i, c_w, c_sk specific heat of ice, water, and of the organic-mineral skeleton, respectively - c_f, c_m, _f, _m specific heat and thermal conductivity in the frozen and melted zones, respectively - c effective heat capacity - thermal conductivity - p density - ₀, _sb bound and strongly bound moisture, respectively - (T) amount of nonfrozen water - R radius of the cylinder - q() heat flux - I functional - u₁(), U₂() measured temperatures of the specimen at the points r = 0 and r = R, respectively, at the instant - ₁, ₂ degree of confidence of the supplementary information - final instant of time - a, b, k, _s positive constants - L specific heat of melting - N number of grid nodes over space - n number of grid nodes over time - h grid step over space - grid step over time - solution of the conjugate system - s number of iteration Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 39, No. 2, pp. 292–297, August, 1980.     

Study of the paramagnetic-antiferromagnetic transition and the γ → ε martensitic transformation in Fe-Mn alloys

The paramagnetic-antiferromagnetic transition and the martensitic transformation of Fe-Mn (Mn 15–32 wt%) alloys have been investigated by resistivity, dilatometry and X-ray diffraction (XRD). The results show that paramagnetic-antiferromagnetic transition increases the resistivity and the volume of alloys, whereas the martensitic transformation reduces the resistivity and volume of alloys. The A _f that was determined by the dilatometric method is not the temperature that martensites in the Fe-Mn alloys have reverse transformed to austenites completely. Mn additions reduce M _s, increase T _N and the lattice parameter of austenite in the Fe-Mn alloys. Both the antiferromagnetic transition and the martensitic transformation lead to an increase in the lattice parameter of austenite. The lattice parameters both above T _N and below T _N decrease linearly with temperature. The lattice parameter below M _s increases first and then decreases. Moreover, the (110) and (002) atomic planes in the Fe-15Mn-0.15C alloy are separated into two peaks: 2 for (002) is 44.16°, 2 for (110) is 44.47°.     

Thermal diffusivity of inhomogeneous systems

The possibility of analyzing the nonsteady temperature fields of inhomogeneous systems using the quasi-homogeneous-body model is investigated.Notation t, t_I, t_i temperature of quasi-homogeneous body inhomogeneous system, and i-th component of system - a, , c thermal diffusivity and conductivity and volume specific heat of quasi-homogeneous body - a_{i i}, c_i same quantities for the i-th component - q heat flux - S, V system surface and volume - x, y coordinates - macrodimension of system - dimensionless temperature Fo=a/² - Bi=/ Fourier and Biot numbers - N number of plates - =h/ ratio of micro- and macrodimensions - _V, volumeaveraged and mean-square error of dimensionless-temperature determination - time - m_i i-th component concentration Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 39, No. 1, pp. 126–133, July, 1980.     

Magnetic field dependence of zero-sound attenuation close to the pair-breaking edge in3He-B due toJ=1−,J z =±1 collective modes

Our previous theory yielded for the Zeeman splitting of the imaginaryJ=1 collective mode in³He-B the result =2+0.25J _z ( is the effective Larmor frequency). In this paper we take into account the downward shift of the pair-breaking edge from 2 to 2₂– (₂ and ₁ are the longitudinal and transverse gap parameters). This leads to a complex Landé factor: the frequencies of theJ _z =±1 components become =2+0.39J _z , and the linewidths of these resonances become finite: =0.18. The coupling amplitudes of theJ _z =±1 components to density are found to be proportional to gap distortion, (₁–₂/(/)². Our results for the ultrasonic attenuation due to theJ _z =±1,J=1 modes are capable of explaining the field dependence of the attenuation close to the pair-breaking edge as observed by Dobbs, Saunders, et al. The observed peak is caused by theJ _z =–1 component: its height increases due to gap distortion as the field is increased, and the peak shifts downward in temperature and its width increases with the field due to the complex Landé factor. TheJ _z =+1 component gives rise to a corresponding dip relative to the continuum attenuation.     

Bounding the Trellis State Complexity of Algebraic Geometric Codes

Let be an algebraic geometric code of dimension k and length n constructed on a curve over F_q. Let be the state complexity of and the Wolf upper bound on . We introduce a numerical function R that depends on the gonality sequence of and show that where g is the genus of . As a matter of fact, R(2g–2)g–(₂–2) with ₂ being the gonality of over F_q, and thus in particular we have that The authors were partially supported respectively by the Grants VA02002 (Junta de Castilla y León), Proc. 300681/97-6 (CNPq-Brazil) and SB2000-0225 (Secretaria de Estado de Educación y Universidades del Ministerio de Educación, Cultura y Deportes de España)     

γ ? α2 Phase transformation in fractured high temperature stress rupture Ti-48Al-2Nb(at.%)

The ₂ phase transformation in fractured high temperature stress rupture Ti-48Al-2Nb(at.%) alloy has been studied by analytical electron microscopy. ₂ and phases were found at grain boundaries. ₂ layers that suspended in layers and interfacial ledge higher than 2d ₍₁₁₁₎ at /₂ interfaces were observed in the lamellar grains. These facts indicated that ₂ phase transformation and dynamic recrystallization have occurred during high temperature stress rupture deformation. It can be concluded that deformation induced ₂ phase transformation and dynamic recrystallization resulted in the presence of particles at grain boundaries. A structural and compositional transition area between deformation-induced ₂(or ) and its adjacently original (or ₂) phases was found by HREM and EDS and is suggested as a way to transform between and ₂ phase during high temperature stress rupture deformation. The transition area was formed by slide of partial dislocations on close-packed planes and diffusion of atoms.     

The variation of the index of refraction in a vortex tube

Three models of a vortex tube (isentropic, isothermal, and isochoric) are considered as optical inhomogeneities. Expressions relating the index of refraction to the coordinate are obtained. The possibility of obtaining Schlieren pictures of such flows is discussed.Notation a speed of sound - n index of refraction - p pressure - r radius - T absolute temperature - v linear velocity - angular deflection of the beam - x adiabatic exponent - density - angular velocity - ¯v, ¯p etc. dimensionless parameters - v₀, ₀ values at the core bounboundary - p, etc. stagnation values - n_c index of refraction at center of vortex     

Standard Gibbs' energies of formation of BaCuO2, Y2Cu2O5 and Y2BaCuO5

The Gibbs' energies of formation of BaCuO₂, Y₂Cu₂O₅ and Y₂BaCuO₅ from component oxides have been measured using solid state galvanic cells incorporating CaF₂ as the solid electrolyte under pure oxygen at a pressure of 1.01×10⁵ Pa BaO + CuO BaCuO₂ G _f,ox ^o (± 0.3) (kJ mol^–1)=–63.4–0.0525T(K) Y₂O₃ + 2CuO Y₂Cu₂O₂ G _f,ox ^o (± 0.3) (kJ mol^–1)=18.47–0.0219T(K) Y₂O₃ + BaO + CuO Y₂BaCuO₅ G _f,ox ^o (± 0.7) (kJ mol^–1)=–72.5–0.0793T(K) Because the superconducting compound YBa₂Cu₃O_7– coexists with any two of the phases CuO, BaCuO₂ and Y₂BaCuO₅, the data on BaCuO₂ and Y₂BaCuO₅ obtained in this study provide the basis for the evaluation of the Gibbs' energy of formation of the 1-2-3 compound at high temperatures.     

The interdependence between the incidence angles associated with quasi-stable intersections during ion erosion

A general discussion, which is valid for any angular dependence of sputtering yieldS=S(), concerning the interdependence between the incidence angles _e and ₀, associated with quasi-stable intersections during ion erosion, is given. The object was firstly to establish the location of _e roots as a function of ₀ and secondly to identify the stationary points and general trend for the complex dependence _e= _e( ₀). The results obtained are applied to a quasi-stability analysis of some specific surface features during ion erosion. Various possible types of quasi-stable intersections (surface-surface, plane-surface, plane-plane) are reviewed from the point of view of their evolution caused by ion bombardment.     

Fracture stress difference of notched polycarbonate between atmospheric pressure and a hydrostatic pressure

Experimental data on fracture stress of polycarbonate (PC) with and without various artificial notches have been obtained at atmospheric pressure and a high hydrostatic pressure (400 MPa). The difference in fracture stress, _F, between both pressures was directly proportional to the intensity of pressure,P, and was inversely proportional to the stress concentration factor of the notch,K _n such that _F following the form of the Kaieda-Oguchi formula, _F. By using the combined stress concentration factor,K _nc, of superposed notch and craze, and by considering the change in elastic modulus due to pressure, the experimental data agreed with the modified Kaieda-Oguchi formula. The stress concentration factor of the craze was calculated by using the Dugdale model.     

Numerical method for calculating the filling of a mold and heat transfer of a melt under the action of centrifugal forces

This paper presents an explicit difference method for solving the conjugate problem of pouring molten metal into a casting mold and its solidification under the action of centrifugal forces with allowance for the free surface.Notation r, z transverse and longitudinal coordinates - u, v horizontal and vertical velocity components - V velocity vector - angular velocity of rotation - P pressure - P normalized pressure - T temperature - time - g free fall acceleration - coefficient of volumetric expansion - C heat capacity - thermal conductivity - density - L crystallization heat - v viscosity - Re=|V|h/v Reynolds grid number - h grid spacing - l mixing length in a turbulent flow - relaxation parameter - coefficient of convective heat transfer - coefficient defining the boundary conditions at the solid wall - D flow divergence - volumetric velocity of filling - emissivity - ₀ Stefan-Boltzmann constant - thickness of a layer Indices r, z, I, j numbers of grid nodes - n number of the integration step with respect to time - L, S temperatures of the liquidus and solidus, respectively - s temperature on the surface - med temperature of the medium - 0 initial state of the system - m metal - mol molten state of the metal - red reduced emissivity in the gap - rad radiant component of the heat transfer coefficient; g, gas-air gap - coat heat-insulating coating - fil filling Dneprodzerzhinsk Industrial Institute. Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 68, No. 4, pp. 678–686, July–August, 1995.     

On the analysis of tunneling data for A15 superconductors

We examine the applicability of the standard McMillan inversion of Eliashberg's equations for superconductors with a nonconstant electronic density of statesN(). We do this usign simple models forN() and a realistically shapedN() taken from recent band structure work for Nb₃Sn. It turns out that peak structure inN() near _F may lead to gross errors in the derived Eliashberg function ²F() when the energy dependence ofN() is omitted in the inversion procedure. For Nb₃Sn, this leads to a 40% overestimate of when ²F() is evaluated via the standard McMillan program.     

The piezoresistance coefficients of copper and copper-nickel alloys

This paper attempts to further a better understanding of the piezoresistance coefficients by studying the piezoresistive effects in copper and copper-nickel alloys. The experimental evidence of isotropic piezoresistance coefficients (₁₁=₁₂) has been obtained for the annealed copper and copper-nickel alloys. The piezoresistance coefficients of the cold-worked copper and Cu₆₀Ni₄₀ alloy are of the tensor character (₁₁₁₂). A physical explanation has been given to the change of the ( _ij ) tensor.