Synthesis, densification and electrical properties of strontium cerate ceramics

Powders of pure and 5% ytterbium substituted strontium cerate (SrCeO₃/SrCe_0.95Yb_0.05O_3−δ) were prepared by spray pyrolysis of nitrate salt solutions. The powders were single phase after calcination in nitrogen atmosphere at 1100 °C (SrCeO₃) and 1200 °C (SrCe_0.95Yb_0.05O_3−δ). Dense SrCeO₃ and SrCe_0.95Yb_0.05O_3−δ materials were obtained by sintering at 1350–1400 °C in air. Heat treatment at 850 and 1000 °C, respectively, was necessary prior to sintering to obtain high density. The dense materials had homogenous microstructures with grain size in the range 6–10 μm for SrCeO₃ and 1–2 μm for SrCe_0.95Yb_0.05O_3−δ. The electrical conductivity of SrCe_0.95Yb_0.05O_3−δ was in good agreement with reported data, showing mixed ionic–electronic conduction. The ionic contribution was dominated by protons below 1000 °C and the proton conductivity reached a maximum of 0.005 S/cm above 900 °C. In oxidizing atmosphere the p-type electronic conduction was dominating above 700 °C, while the contribution from n-type electronic conduction only was significant above 1000 °C in reducing atmosphere.     

Nanosized perovskite-type oxides La1−xSrxMO3−δ (M = Co, Mn; x = 0, 0.4) for the catalytic removal of ethylacetate

Nanometer perovskite-type oxides La_1−xSr_xMO_3−δ (M = Co, Mn; x = 0, 0.4) have been prepared using the citric acid complexing-hydrothermal-coupled method and characterized by means of techniques, such as X-ray diffraction (XRD), BET, high-resolution scanning electron microscopy (HRSEM), X-ray photoelectron spectroscopy (XPS), temperature-programmed desorption (TPD), and temperature-programmed reduction (TPR). The catalytic performance of these nanoperovskites in the combustion of ethylacetate (EA) has also been evaluated. The XRD results indicate that all the samples possessed single-phase rhombohedral crystal structures. The surface areas of these nanomaterials ranged from 20 to 33 m² g⁻¹, the achievement of such high surface areas are due to the uniform morphology with the typical particle size of 40–80 nm (as can be clearly seen in their HRSEM images) that were derived with the citric acid complexing-hydrothermally coupled strategy. The XPS results demonstrate the presence of Mn⁴⁺ and Mn³⁺ in La_1−xSr_xMnO_3−δ and Co³⁺ and Co²⁺ in La_1−xSr_xCoO_3−δ, Sr substitution induced the rises in Mn⁴⁺ and Co³⁺ concentrations; adsorbed oxygen species (O⁻, O₂⁻, or O₂²⁻) were detected on the catalyst surfaces. The O₂-TPD profiles indicate that Sr doping increased desorption of the adsorbed oxygen and lattice oxygen species at low temperatures. The H₂-TPR results reveal that the nanoperovskite catalysts could be reduced at much lower temperatures (<240 °C) after Sr doping. It is observed that under the conditions of EA concentration = 1000 ppm, EA/oxygen molar ratio = 1/400, and space velocity = 20,000 h⁻¹, the catalytic activity (as reflected by the temperature (T_100%) for EA complete conversion) increased in the order of LaCoO_2.91 (T_100% = 230 °C) ≈ LaMnO_3.12 (T_100% = 235 °C) < La_0.6Sr_0.4MnO_3.02 (T_100% = 190 °C) < La_0.6Sr_0.4CoO_2.78 (T_100% = 175 °C); furthermore, there were no formation of partially oxidized by-products over these catalysts. Based on the above results, we conclude that the excellent catalytic performance is associated with the high surface areas, good redox properties (derived from higher Mn⁴⁺/Mn³⁺ and Co³⁺/Co²⁺ ratios), and rich lattice defects of the nanostructured La_1−xSr_xMO_3−δ materials.     

Thermoelectric characterization of NaxMx/2Ti1−x/2O2 (M=Co, Ni and Fe) polycrystalline materials

Layered -titanate materials, Na_xM_x/2Ti_1−x/2O₂ (M=Co, Ni and Fe, x=0.2–0.4), were synthesized by flux reactions, and electrical properties of polycrystalline products were measured at 300–800 °C. After sintering at 1250 °C in Ar, all products show n-type thermoelectric behavior. The values of both d.c. conductivity and Seebeck coefficient of polycrystalline Na_0.4Ni_0.2Ti_0.8O₂ were ca. 7×10³ S/m and ca. −193 μV/K around 700 °C, respectively. The measured thermal conductivity of layered -titanate materials has lower value than conductive oxide materials. It was ca. 1.5 Wm⁻¹ K⁻¹ at 800 °C. The estimated thermoelectric figure-of-merit, Z, of Na_0.4Ni_0.2Ti_0.8O₂ and Na_0.4Co_0.2Ti_0.8O₂ was about 1.9×10⁻⁴ and 1.2×10⁻⁴ K⁻¹ around 700 °C, respectively.     

Direct evidence for purely silver ion conduction in CuI-doped silver oxysalt superionic systems: Combined electrolysis and EDS studies

Maiden attempt has been made for the direct estimation of the contributions of silver and copper ions to the ionic conductivity in superionic solids obtained in CuI-doped silver oxysalt systems. The application of the combined electrolysis and EDS techniques towards qualitative and quantitative analyses of the mobile ionic species in solid electrolyte systems having more than one possible mobile ion is reported. These studies confirmed that these electrolyte materials are purely Ag⁺ conducting up to 50 mol% CuI in xCuI–(100 − x)[2Ag₂O–0.7V₂O₅–0.3B₂O₃] and xCuI–(100 − x)[Ag₂O–0.7MoO₃–0.3WO₃] systems and small fraction of t_Cu+ exists above 60 mol% CuI. These solid electrolyte materials exhibited a high ionic transport numbers (t_i) of >0.985 and the t_i increases when two glass formers are used.     

Ionic conductivity of PEO9: Cu(CF3SO3)2: Al2O3 nano-composite solid polymer electrolyte

Cu⁺⁺ ion containing solid polymer electrolytes exhibit interesting electrochemical properties. In particular, the polymer electrolyte PEO₉:Cu(CF₃SO₃)₂ made by complexing copper triflate (CuTf₂) with PEO appears to show scientifically intriguing transport properties. Although some copper ion transport in these systems has been seen from plating stripping processes, the detailed mechanism of ionic transport and the species involved are yet to be established. In order to obtain enhanced ionic conductivities and also to contribute towards understanding the ionic transport process in Cu⁺⁺ ion containing, PEO based composite polymer electrolytes, we have studied the system PEO₉: CuTf₂: Al₂O₃ incorporating 10 wt.% of alumina filler particles of grain size 10 μm, 37 nm, 10–20 nm and also particles of pore size 5.8 nm. Thermal and electrical measurements show that the system remains amorphous down to room temperature. The composite electrolyte is predominantly an ionic conductor with electronic conductivity less than 2%. The triflate (CF₃SO₃⁻) anions appear to be the dominant carriers. The presence of alumina grains has enhanced the conductivity significantly from room temperature up to 100 °C. The nano-porous grains with 5.8 nm pore size and 150 m²/g specific surface area exhibited the maximum conductivity enhancement. This enhancement has been attributed to Lewis acid–base type surface interactions of ionic species with O²⁻ and OH⁻ groups on the filler grain surface.     

Effect of structural and electrochemical properties of different Cr-doped contents of Li[Ni1/3Mn1/3Co1/3]O2

Layered Li[Ni_(1−x)/3Mn_(1−x)/3Co_(1−x)/3Cr_x]O₂ materials with x = 0, 0.01, 0.02, 0.03, 0.05 are prepared by a solid-state pyrolysis method. The oxide compounds were calcined with various Cr-doped contents, which result in greater difference in morphological (shape, particle size and specific surface area) and the electrochemical (first charge profile, reversible capacity and rate capability) differences. The Li[Ni_(1−x)/3Mn_(1−x)/3Co_(1−x)/3Cr_x]O₂ powders were characterized by means of X-ray diffraction (XRD), charge/discharge cycling, cyclic voltammetry, and SEM. XRD experiment revealed that the Li[Ni_(1−x)/3Mn_(1−x)/3Co_(1−x)/3Cr_x]O₂ (x = 0, 0.01, 0.02, 0.03, 0.05) were crystallized to well layered -NaFeO₂ structure. The first specific discharge capacity and coulombic efficiency of the electrode of Cr-doped materials were higher than that of pristine material. When x = 0.02, the sample showed the highest first discharge capacity of 241.9 mAh g⁻¹ at a current density of 30 mA g⁻¹ in the voltage range 2.3–4.6 V, and the Cr-doped samples exhibited higher discharge capacity and better cycleability under medium and high current densities at room temperature.     

EMF measurements on gadolinia doped ceria

An experimental set up was built to measure the EMF, which is generated out of the oxygen partial pressure gradient, across the faces of solid electrolyte samples. The results obtained from this work show that ceria-gadolinia mixed oxide, of composition Ce_0·825Gd_0·175O_1·913, behaves in a manner quite satisfactory for use as an oxygen ion conducting material in fuel cells. This is especially true at relatively low temperatures (as low as 600°C) and with oxygen partial pressure down to 10⁻⁵ atm. The oxygen mean ionic transport number was shown to be almost unity at the above mentioned temperature and oxygen partial pressure.     

Thermodynamic studies on hydrogen adsorption on the zeolites Na-ZSM-5 and K-ZSM-5

Adsorption of dihydrogen onto the zeolites Na-ZSM-5 and K-ZSM-5 renders the fundamental H–H stretching mode infrared active. The corresponding infrared absorption bands were found at 4101 and 4112 cm⁻¹ for H₂/Na-ZSM-5 and H₂/K-ZSM-5, respectively. Thermodynamic characterization of the adsorbed state was carried out by means of variable-temperature infrared spectroscopy; simultaneously measuring integrated band intensity, temperature and equilibrium pressure of the gas phase. For the H₂/Na-ZSM-5 system, the standard adsorption enthalpy and entropy resulted to be ΔH° = −10.3 (±0.5) kJ mol⁻¹ and ΔS° = −121 (±10) J mol⁻¹ K⁻¹. For H₂/K-ZSM-5 corresponding values were −9.1 (±0.5) kJ mol⁻¹ and −124 (±10) J mol⁻¹ K⁻¹, respectively.     

Preparation of ultra-active alumina of designed porous structure by successive hydrothermal and thermal treatments of porous anodic Al2O3 films

A porous anodic alumina film was prepared by the anodic oxidation of Al metal sheet in a thermostated and vigorously stirred bath of H₂SO₄ 15% (w/v) at a temperature of 25°C and a current density of 15 mA cm⁻². It had a geometric surface area of 33 cm², a surface density of pores 1.269×10¹¹ cm⁻² and the maximum limiting thickness and porosity achieved at these conditions which are 50.3 μm and 0.42, respectively. This oxide was tried in the catalytic test reaction of the decomposition of HCOOH at temperatures 270–390°C. Then, the oxide was treated hydrothermally in H₂O at 100°C for 5 h and tried in the same test reaction. The procedure of hydrothermal treatment and catalysis experiment was repeated 40 times. In all cases the oxide showed an almost exclusively dehydrative catalytic effect, 98–100%. Both the total activity of the alumina film with the aforementioned constant geometric surface area and its specific activity referred to the unit of oxide mass gave a maximum in the first and a minimum about the fourth hydrothermal treatment; then, they increased strongly with the order of hydrothermal treatment. Despite the decrease of the oxide mass during hydrothermal treatment, the final promotion of the total catalytic activity of oxide was 13.7–10.6 times that of non-treated oxide for temperatures 330–390°C. The corresponding promotion of specific activity was 31.5–24.5 times that of the non-treated oxide. The results of the present study showed that the successive hydrothermal and thermal treatments of porous anodic Al₂O₃ films produce more and more active alumina catalysts. In this way ultra-active alumina catalysts or supports can be prepared.     

Application of Ce0.33Zr0.63Pr0.04O2-supported noble metal catalysts in the catalytic wet air oxidation of 2-chlorophenol: Influence of the reaction conditions

In this work, different procedures, namely carbonate coprecipitation and modified solid–solid diffusion, were used to prepare hexaaluminate samples, unsupported or supported onto θ-Al₂O₃. These samples were used as catalyst for the methane total oxidation as synthesized or after impregnation of 1 wt% Pd. It was observed that the modified solid–solid diffusion procedure is an efficient method to obtain the hexaaluminate structure. At a theoretical ratio x of hexaaluminate onto Al₂O₃ less than 0.6 (xLa_0.2Sr_0.3Ba_0.5MnAl₁₁O₁₉ + (1−x)·Al₂O₃, with x = 0.25, 0.60), samples with high specific surface area and θ-Al₂O₃ structure are then obtained. Large differences in catalytic activity can be observed among the series of sample synthesized. All the pure oxide samples (i.e. without palladium) present low catalytic activity for methane total oxidation compared to a reference Pd/Al₂O₃ catalyst. The highest activity was obtained for the samples presenting a θ-Al₂O₃ structure (with x = 0.60) and a high surface area. Impregnation of 1 wt% palladium resulted in an increase in catalytic activity, for all the solids synthesized in this work. Even if the lowest light-off temperature was obtained on the reference sample, similar methane conversions at high temperature (700 °C) were obtained on the stabilized θ-Al₂O₃ solids (x = 0.25, 0.60). Moreover, the reference sample is found to strongly deactivate with reaction time at the temperature of test (700 °C), due to a progressive reduction of the PdO_x active phase into the less active Pd° phase, whereas excellent stabilities in reaction were obtained on the pure and palladium-doped hexaaluminate and supported θ-Al₂O₃ samples. This clearly showed the beneficial effect of the support for the stabilization of the PdO_x active phase at high reaction temperature. These properties are discussed in term of oxygen transfer from the support to the palladium particle. Oxygen transfer is directly related to the Mn³⁺/Mn²⁺ redox properties (in the case of the hexaaluminate and stabilized θ-Al₂O₃ samples), that allows a fast reoxidation of the metal palladium sites since palladium sites reoxidation cannot occur directly by gaseous dioxygen adsorption and dissociation on the surface.     

Catalytic oxidation of methane over hexaaluminates and hexaaluminate-supported Pd catalysts

An aqueous (NH₄)₂CO₃ coprecipitation method, based on that of Groppi et al. [Appl. Catal. A 104 (1993) 101–108] was used to synthesize Sr_1−xLa_xMnAl₁₁O₁₉₋ hexaaluminates. These materials were first synthesized by alkoxide hydrolysis. This synthesis route requires special handling of the starting materials and is not likely to be commercially practical. The materials prepared by (NH₄)₂CO₃ coprecipitation have similar surface areas as those prepared by the alkoxide hydrolysis method. Their CH₄ oxidation activity, measured as the temperature needed for 10% conversion of methane, is higher than those prepared by alkoxide hydrolysis. The La-substantiated material, LaMnAl₁₁O₁₉₋, shows high surface area with 19.3 m²/g after calcination at 1400°C for 2 h. It is active for CH₄ oxidation with T_10% at 450°C using 1% CH₄ in air and 70 000 cm³/h g space velocity. The stability and activity of LaMnAl₁₁O₁₉₋ prepared by (NH₄)₂CO₃ coprecipitation method is a simple and important step forward for the application of CH₄ catalytic combustion for gas turbines.     

Redox behavior and selective oxidation properties of mesoporous titano- and zirconosilicate MCM-41 molecular sieves

Mesoporous titano- and zirconosilicate molecular sieves, Ti-MCM-41 and Zr-MCM-41, respectively, with Si/M ratios in the range from 11 to 96 (M=Ti or Zr), have been synthesized by the hydrothermal method and characterized by XRD, XRF, N₂ adsorption and diffusive reflectance UV–Vis (DRUV–Vis), FT-IR and electron spin resonance (ESR) spectroscopic techniques. The redox behavior and selective oxidation properties of these materials have been investigated. ESR of samples reduced with LiAlH₄ (298 K) and H₂ (673–873 K) reveals two types of metal ion species: species I^′ located inside the pore walls and species I^′′ located at the pore surface. The reduced species I^′′ are highly reactive towards oxygen and form M(O₂^−·) radicals. The M(O₂^−·) radicals were also observed when the samples were reacted with aqueous H₂O₂ or tert-butylhydroperoxide (TBHP). ESR studies reveal that Ti-MCM-41 is easier to reduce and reoxidize than Zr-MCM-41. The DRUV–Vis spectra are consistent with a monoatomic dispersion of the metal ions. In the samples with high metal loading the presence of a nanocrystalline metal oxide phase cannot be ruled out. Both Ti-MCM-41 and Zr-MCM-41 catalyze the hydroxylation of 1-naphthol with aqueous H₂O₂ and the epoxidation of norbornylene with TBHP.     

Use of unsupported and silica supported molybdenum carbide to treat chloroarene gas streams

The gas phase catalytic hydrodechlorination (HDC) of mono- and di-chlorobenzenes (423 K ≤ T ≤ 593 K) over unsupported and silica supported Mo carbide (Mo₂C) is presented as a viable means of detoxifying Cl-containing gas streams for the recovery/reuse of valuable chemical feedstock. The action of Mo₂C/SiO₂ is compared with MoO₃/SiO₂ and Ni/SiO₂ (an established HDC catalyst). The pre- and post-HDC catalyst samples have been characterized in terms of BET area, TG-MS, TPR, TEM, SEM, H₂ chemisorption/TPD and XRD analysis. Molybdenum carbide was prepared via a two step temperature programmed synthesis where MoO₃ was first subjected to a nitridation in NH₃ followed by carbidization in a CH₄/H₂ mixture to yield a face-centred cubic (-Mo₂C) structure characterized by a platelet morphology. Pseudo-first order kinetic analysis was used to obtain chlorobenzene HDC rate constants and the associated temperature dependences yielded apparent activation energies that decreased in the order MoO₃/SiO₂ (80 ± 5 kJ mol⁻¹) ≈ MoO₃ (78 ± 8 kJ mol⁻¹) > Ni/SiO₂ (62 ± 3 kJ mol⁻¹) ≈ -Mo₂C (56 ± 6 kJ mol⁻¹) ≈ -Mo₂C/SiO₂ (53 ± 3 kJ mol⁻¹). HDC activity was lower for the dechlorination of the dichlorobenzene reactants where steric hindrance influenced chloro-isomer reactivity. Supporting -Mo₂C on silica served to elevate HDC performance, but under identical reaction conditions, Ni/SiO₂ consistently delivered a higher initial HDC activity. Nevertheless, the decline in HDC performance with time-on-stream for Ni/SiO₂ was such that activity converged with that of -Mo₂C/SiO₂ after three reaction cycles. A temporal loss of HDC activity (less extreme for the carbides) was observed for each catalyst that was studied and is linked to a disruption to supply of surface active hydrogen as a result of prolonged Cl/catalyst interaction.     

Formation of LiNixCo1−xO2 by decarbonization of organic gel precursors through treatment with nitric acid and hydrogen peroxide

We have used a complex sol–gel process to synthesize a family of compounds LiNi_xCo_1−xO₂ (x = 0, 0.25, 0.5, 0.75, 1). These compounds are candidates for electrode materials in high-energy-density batteries. Starting sols were prepared from xNi²⁺ + (1 − x) Co²⁺ acetates/ascorbic acid aqueous solutions by alkalizing with LiOH and NH₃. With thermal treatment in air, nickel carbonates formed in quantities roughly proportional to Ni concentration. The carbonate impurities could not be fully removed by heating in air to high temperatures. Because formation of pure layered oxides was inhibited by the presence of the carbonates, we developed a new way to remove them from just-formed precursors by treating the intermediate phases (those formed after calcination at 750 °C) with concentrated HNO₃ and H₂O₂. All resulting powders were phase pure by X-ray diffraction and were easily friable. Various electrochemical properties of compacts prepared from these powders were measured.     

Production of high porosity nanoparticles of cerium oxide in clay

Cerium oxide nanoparticles modified montmorillonite was obtained by interaction of a clay with (NH₄)₂Ce(NO₃)₆. The mean size of cerium oxide nanoparticles in clay was at 3.5 nm. The product was an amorphous solid and showed high permanent porosity and stability at high temperatures. The amorphous structure of the sample was proven by X-ray diffraction and electronic diffraction. The porous structure was studied by means of chemisorption and it was shown that samples calcined at 550 °C had S_BET = 239 m²/g; micropore volume = 0.1839 cm³/g; average pore diameter = 3.07 nm.     

Influence of the CO2 back flux on the reaction mechanisms of BaTiO3 formation from high TiO2 content in TiO2---BaCO3 mixtures

The solid state reactions between 18.2% mol BaCO₃−81.8% mol TiO₂ powders were investigated in the initial stage of the process where BaTiO₃ is the only solid product. In O₂ (g) environment BaTiO₃ formation occurs in two regimes. The first one is characterized by a total apparent activation entalphy (ΔH⁺) of 42 kJ/mol ± 20 kJ/mol. The second one is a more activated process with ΔH⁺ equal to 230 kJ/mol ± 25 kJ/mol. In CO₂ (g) environment and ‘In vacuo’ there was only one activated process with a ΔH⁺ respectively equal to 222 kJ/mol ± 25 kJ/mol and to 20 kJ/mol ± 10 kJ/mol. The low activated mechanism is consisted with a layered interphase model, while the high activated step requires a bulk phenomena such as needle-like crystals BaTiO₃ grown from TiO₂ particles.     

Characterization of Pd-based FCC CO/NOx control additives by in situ FTIR and extended X-ray absorption fine structure spectroscopies

Pdⁿ⁺/Ceⁿ⁺/Na⁺/γ-Al₂O₃-type materials used as FCC additives for CO/NO_x control were characterized by extended X-ray absorption fine structure (EXAFS) spectroscopy and in situ FTIR. The EXAFS data indicate that in freshly prepared samples palladium is present in the form of highly dispersed PdO species. Reduction with H₂ at 500 °C leads to the formation of small Pd clusters incorporating on average approximately six to eight metal atoms at a Pd−Pd bond distance of 2.76 Å. All components of these materials can interact with NO and promote the formation of nitrate/nitrite species, essentially “trapping” NO_x species on the catalyst surface. However, the Na⁺ species dominate the surface chemistry and readily form sodium nitrates with a characteristic IR band at 1370–1385 cm⁻¹. Finally, hydroxyls from the support are also actively participating in the formation of HNO_x type compounds with characteristic stretching vibrations in the 3500–3572 cm⁻¹ region.     

Conductivity of Na5+xYAlxSi4-xO12 ceramics

A series of ceramics samples, Na_5+xYAl_xSi_4-xO₁₂, has been prepared by a solid state reaction with the starting materials of SiO₂, Y₂O₃, Al₂O₃ and Na₂CO₃. Their crystalline structure and morphology have been studied by the determination of XRD, IR, TG, DTA and SEM. Their conductivity has been measured by means of the complex impedance method. The dependence of the conductivity and density of the samples on the amount of the added Al₂O₃ and the reaction between the conductivity and the temperature have been discussed. When x = 0, the density of the sintering sample is 90% T.D., and the conductivity is 1·48 x 10⁻¹ (ωcm)⁻¹ at 300°C; when x = 0·1, the density is up to 97% T.D., and the conductivity up to 1·74 x 10⁻¹ (ω cm)⁻¹ at 300°C.     

Microwave-enhanced catalytic degradation of phenol over nickel oxide

A mix-valenced nickel oxide, NiO_x, was prepared from nickel nitrate aqueous solution through a precipitation with sodium hydroxide and an oxidation by sodium hypochlorite. Further, pure nickel oxide was obtained from the NiO_x by calcination at 300, 400 and 500 °C (labeled as C300, C400 and C500, respectively). They were characterized by thermogravimetry (TG), X-ray diffraction (XRD), nitrogen adsorption at −196 °C and temperature-programmed reduction (TPR). Their catalytic activities towards the degradation of phenol were further studied under continuous bubbling of air through the liquid phase. Also, the effects of pH, temperature and kinds of nickel oxide on the efficiency of the microwave-enhance catalytic degradation (MECD) of phenol have been investigated. The results indicated that the relative activity affected significantly with the oxidation state of nickel, surface area and surface acidity of nickel oxide, i.e., NiO_x (>+2 and S_BET = 201 m² g⁻¹)  C300 (+2 and S_BET = 104 m² g⁻¹) > C400 (+2 and S_BET = 52 m² g⁻¹) > C500 (+2 and S_BET = 27 m² g⁻¹). The introduction of microwave irradiation could greatly shorten the time of phenol degradation.     

Comparative study of lithium ion conductors in the system Li1+xAlxA2−x (PO4)3 with A=Ti or Ge and 0≤x≤0·7 for use as Li sensitive membranes

Preparations and physico-chemical characterizations of NASICON-type compounds in the system Li_1+xAl_xA_2−x^IV(PO₄)₃ (A^IV=Ti or Ge) are described. Ceramics have been fabricated by sol-gel and co-grinding processes for use as ionosensitive membrane for Li⁺ selective electrodes. The structural and electrical characteristics of the pellets have been examined. Solid solutions are obtained with Al/Ti and Al/Ge substitutions in the range 0≤x≤0·6. A minimum of the rhombohedral c parameter appears for x about 0·1 for both solutions. The grain ionic conductivity has been characterized only in the case of Ge-based compounds. It is related to the carrier concentration and the structural properties of the NASICON covalent skeleton. The results confirm that the Ti-based framework is more calibrated to Li⁺ migration than the Ge-based one. A grain conductivity of 10⁻³ S cm⁻¹ is obtained at 25°C in the case of Li_1·3Al_0·3Ti_1·7(PO₄)₃. A total conductivity of about 6×10⁻⁵ S cm⁻¹ is measured on sintered pellets because of grain boundary effects. The use of such ceramics in ISE devices has shown that the most confined unit cell (i.e. in Ge-based materials) is more appropriate for selectivity effect, although it is less conductive.©