Zn$_{1 - x}$Mg$_{x}$ O Homojunction-Based Ultraviolet Photodetector

Zn$_{1 - {x}}$ Mg$_{x}$ O p-n photodiodes were fabricated on (0001) sapphire substrates using a pulsed laser deposition technique with different Mg contents. Ti–Au and Ni–Au metals deposited using vacuum evaporation were used as n-type and p-type contacts, respectively. The X-ray diffraction analysis showed the Zn$_{1 - {x}}$Mg$_{x}$O double layers have a single phase hexagonal wurtzite structure. The optical bandgap of Zn$_{1 - {x}}$Mg$_{x}$O films has been tuned from 3.27 to 4.26 eV by increasing the Mg content ${x} =0.0$ to ${x}=0.34$. Correspondingly, the cutoff wavelength of the resultant detectors varies from 380 to 284 nm. Zn$_{1 - {x}}$Mg$_{x}$O p-n photodiodes with different Mg contents exhibit very good performance, with a very low dark current (${≪}$ 20 pA) at the bias voltage of 10 V. The ultraviolet to visible rejection ratio is more than three orders of magnitude.      

Low Loss Si–SiO $_{2}$–Si 8-nm Slot Waveguides

Quasi-transverse-magnetic-mode propagation loss of 1.83 dB/cm at $lambda = 1.565~muhbox{m}$ is achieved in horizontal Si(amorphous)–SiO $_{2}$–Si(crystalline) slot waveguides with 8.3-nm slots fabricated on silicon-on-insulator. Waveguide loss is measured using a ring resonator with $Q {sim 3}times{10} ^{5}$.      

Nitride-Based Asymmetric Two-Step Light-Emitting Diode With In$_{0.08}$ Ga$_{0.92}$ N Shallow Step

A nitride-based asymmetric two-step light-emitting diode (LED) with $hbox{In}_{0.08} hbox{Ga}_{0.92}hbox{N}$ shallow step was proposed and fabricated. It was found that the low indium content $hbox{In}_{0.08} hbox{Ga}_{0.92}hbox{N}$ layer can significantly enhance phase separation and/or inhomogeneous indium distribution in the active $hbox{In}_{0.27}hbox{Ga}_{0.73}hbox{N}$ layer. It was also found that we can enhance LED output power by a factor of 2.27 by simply inserting an $hbox{In}_{0.08} hbox{Ga}_{0.92}hbox{N}$ shallow step.      

2 MHz AO $Q$ -switched ${rm TEM}_{00}$ Grazing Incidence Laser With 3 at.% Neodymium Doped Nd:YVO$_{4}$

We present a detailed experimental and theoretical study of the ultrahigh repetition rate AO $Q$ -switched ${rm TEM}_{00}$ grazing incidence laser. Up to 2.1 MHz $Q$-switching with ${rm TEM}_{00}$ output of 8.6 W and 2.2 MHz $Q$ -switching with multimode output of 10 W were achieved by using an acousto-optics $Q$ -switched grazing-incidence laser with optimum grazing-incidence angle and cavity configuration. The crystal was 3 at.% neodymium doped Nd:YVO$_{4}$ slab. The pulse duration at 2 MHz repetition rate was about 31 ns. The instabilities of pulse energy at 2 MHz repetition rate were less than ${pm}6.7hbox{%}$ with ${rm TEM}_{00}$ operation and ${pm}3.3hbox{%}$ with multimode operation respectively. The modeling of high repetition rate $Q$-switched operation is presented based on the rate equation, and with the solution of the modeling, higher pump power, smaller section area of laser mode, and larger stimulated emission cross section of the gain medium are beneficial to the $Q$-switched operation with ultrahigh repetition rate, which is in consistent with the experimental results.      

The Performance of Acoustic-Optical $Q$-switched Mode-Locking 1.34 $mu$m Nd:GdVO$_{4}$ Laser

A diode-end-pumped $Q$ -switched mode-locking $hbox{Nd:GdVO}_{4}$ laser operating at 1.34 $mu{hbox {m}}$ with an acousto-optical (AO) Q-switch in a compact V-type cavity was realized in our experiment for the first time. When the AO Q-switch repetition rate was 10 kHz, the maximum average output power of 750 mW and the pulse energy of 75 $muhbox{J}$ were obtained at the maximum incident pump power of 9 W. The mode-locking modulation depth of about 100% was obtained at certain pump power over the threshold. The mode-locked pulse inside in the $Q$-switched pulse had a repetition rate of 341 MHz, and its average pulsewidth was estimated to be about 350 ps. A developed rate equation model for the $Q$ -switched and mode-locked lasers with an AO Q-switch were proposed by using the hyperbolic secant functional methods. The results of numerical calculations of the rate equations were in good agreement with the experimental results.      

Enhanced Vertical Light Extraction From Ultrathin Amorphous Si–Si$_{3}$ N$_{4}$ Multilayers With Photonic Crystal Patterns

We have investigated the significant enhancement of light extraction from amorphous Si-Si₃N₄ multiple-quantum-well structures, in which two-dimensional hexagonal-lattice air-hole photonic crystals (PCs) were integrated. The vertical spectral integrated intensity of light emission around 674 nm was enhanced up to times due to strong coupling to the inherent leaky modes or radiation modes near Gamma point of PC's band structure. The experimental observations also suggested that coupling to leaky modes should be more beneficial for light extraction enhancement.     

Nonvolatile-Memory Characteristics of $hbox{AlO}^{-}$ -Implanted $hbox{Al}_{2}hbox{O}_{3}$

The nonvolatile-memory (NVM) characteristics of $hbox{AlO}^{-}$ -implanted $hbox{Al}_{2}hbox{O}_{3}$ structures are reported and shown to exhibit promising behaviors, including fast program/erase speeds and high-temperature data retention. Photoconductivity spectra show the existence of two dominant trap levels, located at around 2 and 4 eV below the conduction band minimum of $hbox{Al}_{2}hbox{O}_{3}$, and our calculations show that these levels are likely attributed to the defects in the $hbox{Al}_{2}hbox{O}_{3}$, such as the Al–O divacancy. The relative concentrations of these defects vary with the implant fluence and are shown to explain the NVM characteristics of the samples irradiated to different fluences.      

High-Performance Poly-Silicon TFTs Using a High-$k$ $hbox{PrTiO}_{3}$ Gate Dielectric

In this letter, a polycrystalline-silicon thin-film transistor (poly-Si TFT) with a high- $k$ $hbox{PrTiO}_{3}$ gate dielectric is proposed for the first time. Compared to TFTs with a $hbox{Pr}_{2}hbox{O}_{3}$ gate dielectric, the electrical characteristics of poly-Si TFTs with a $hbox{PrTiO}_{3}$ gate dielectric can be significantly improved, such as lower threshold voltage, smaller subthreshold swing, higher $I_{rm on}/I_{rm off}$ current ratio, and larger field-effect mobility, even without any hydrogenation treatment. These improvements can be attributed to the high gate capacitance density and low grain-boundary trap state. All of these results suggest that the poly-Si TFT with a high- $k$ $hbox{PrTiO}_{3}$ gate dielectric is a good candidate for high-speed and low-power display driving circuit applications in flat-panel displays.      

Analytical Model of $I$– $V$ Characteristics of Arbitrarily Shallow p-n Junctions

For the first time, an analytical model of arbitrarily shallow p-n junctions is presented. Depending on the junction depth, electrical characteristics of ultrashallow p-n junctions can vary from the characteristics of standard Schottky diodes to standard deep p-n junctions. This model successfully unifies the standard Schottky and p-n diode expressions. In the crossover region, where the shallow doping region can be totally depleted, electrical characteristics phenomenologically substantially different from typical diode characteristics are predicted. These predictions and the accuracy of the presented model are evaluated by comparison with the MEDICI simulations. Furthermore, ultrashallow $hbox{n}^{+}$-p diodes were fabricated, and the anomalous behavior in the crossover regime was experimentally observed.      

Fabrication and Characterization of Coplanar Waveguides on Silicon Using a Combination of SiO $_{2}$ and SRO $_{20}$

In this work, the use of silicon rich oxide (SRO) and chemical vapor deposition SiO$_{2}$ double layers as passivation films of coplanar waveguides (CPW) on high resistivity silicon (HR-Si) with an ${hbox{N}}^{+}$ backside is studied. The microwave performance of the fabricated CPWs is evaluated by computing the attenuation loss of the devices in the 0.045–50 GHz frequency range. Experimental results show that the ${hbox{N}}^{+}$ layer can be used without affecting CPW performance. Also, using a combined dielectric layer (SRO$_{20}$ /SiO$_{2}$ ), the attenuation losses are reduced compared to single dielectric layers.      

${K}_{a}$ –Band All-Resonant Photonic Microwave Receiver

We demonstrate a microwave photonic receiver operating at 35-GHz carrier frequency with a sensitivity exceeding ${-}$70 dBm in a 3-MHz frequency band and possessing more than 40-dB dynamic range when operated in the direct detection mode. The receiver is based on a lithium niobate optical whispering gallery mode resonator coupled to a microwave strip line resonator. We theoretically analyze the performance of the receiver and estimate its optimal achievable sensitivity and dynamic range.      

Optimal $ Sigma Delta$ Modulator Architectures for Fractional-$ {N}$ Frequency Synthesis

This paper presents a comparative study of $Sigma Delta$ modulators for use in fractional-$ {N}$ phase-locked loops. It proposes favorable modulator architectures while taking into consideration not only the quantization noise of the modulator but also other loop nonidealities such as the charge pump current mismatch that contributes to the degradation in the synthesized tone's phase noise. The proper choice of the modulator architecture is found to be dependent upon the extent of the nonideality, reference frequency, and loop bandwidth. Three modulator architectures are then proposed for low, medium, and high levels of nonidealities.      

Impact of Design on High-Frequency Performance of Advanced MIM Capacitors Using Si $_{3}$N $_{4}$ Dielectric Layers

High-frequency characterizations of ultra thin 32 nm PECVD Si$_{3}$N $_{4}$ dielectric in an advanced metal–insulator–metal (MIM) capacitors are presented, with focus on the impact of design on the performance of MIM capacitors. Frequency dependent capacitance has been extracted over a wide range of frequency bandwidth. An equivalent model circuit of capacitors including four parameters was developed to explain this behavior. The results have been compared with the values obtained from a 3-D electromagnetic modeling. A specific chart has been introduced to predict the electrical performance of new MIM capacitor designs.      

Experimental Demonstration of Deeply-Etched SiO$_{2}$ Ridge Optical Waveguides and Devices

Deeply-etched ${hbox{SiO}}_{2}$ optical ridge waveguides are fabricated and characterized. A detailed discussion of the fabrication process (especially for the deep etching process) is presented. The measured propagation losses for the fabricated waveguides with different core widths range from $0.33sim {hbox {0.81}}~{hbox {dB}}/{hbox {mm}}$. The loss is mainly caused by the scattering due to the sidewall roughness. The losses in bending sections are also characterized, which show the possibility of realizing a small bending radius (several tens of microns). 1 $,times {rm N}$ ( ${rm N}=2$, 4, 8) multimode interference couplers based on the deeply-etched ${hbox{SiO}}_{2}$ ridge waveguide are also fabricated and show fairly good performances.      

Eigendecomposition of Images Correlated on $S^{1}$, $S^{2}$, and $SO(3)$ Using Spectral Theory

Eigendecomposition represents one computationally efficient approach for dealing with object detection and pose estimation, as well as other vision-based problems, and has been applied to sets of correlated images for this purpose. The major drawback in using eigendecomposition is the off line computational expense incurred by computing the desired subspace. This off line expense increases drastically as the number of correlated images becomes large (which is the case when doing fully general 3-D pose estimation). Previous work has shown that for data correlated on S ¹ , Fourier analysis can help reduce the computational burden of this off line expense. This paper presents a method for extending this technique to data correlated on S ² as well as SO(3) by sampling the sphere appropriately. An algorithm is then developed for reducing the off line computational burden associated with computing the eigenspace by exploiting the spectral information of this spherical data set using spherical harmonics and Wigner-D functions. Experimental results are presented to compare the proposed algorithm to the true eigendecomposition, as well as assess the computational savings.     

A $Q$– $f$ Droop Curve for Facilitating Islanding Detection of Inverter-Based Distributed Generation

This paper presents a new method for islanding detection of distributed generation (DG) inverter that relies on analyzing the reactive power versus frequency (Q-f) characteristic of the DG and the islanded load. The proposed method is based on equipping the DG interface with a Q-f droop curve that forces the DG to lose its stable operation once an islanding condition occurs. A simple passive islanding detection scheme that relies on frequency relays can then be used to detect the moment of islanding. The performance of the proposed method is evaluated under the IEEE 1547 and UL 1741 antiislanding test configuration. The studies reported in this paper are based on time-domain simulations in the power systems computer-aided design (PSCAD)/EMTDC environment. The results show that the proposed technique has negligible nondetection zone and is capable of accurately detecting islanding within the standard permissible detection times. In addition, the technique proves to be robust under multiple-DG operation.     

Cooperative Quantum Cutting in Yb $^{3+}$–Tb $^{3+}$ Codoped Borosilicate Glasses

Quantum cutting down-conversion (DC) with the emission of two near-infrared photons for each blue photon absorbed is realized in $hbox{Yb}^{3+}hbox{–}hbox{Tb}^{3+}$ codoped borosilicate glasses. With the excitation of $hbox{Tb}^{3+}$ ion by a 484-nm monochromatic light, emission from the $^{2} hbox{F} _{5/2}rightarrow ^{2} hbox{F} _{7/2}$ transition of $hbox{Yb}^{3+}$ ions is observed and this emission is proved to originate from the DC between $hbox{Tb}^{3+}$ ions and $hbox{Yb}^{3+}$ ions. Results shows that maximum quantum efficiency reach as high as 153%, which is comparable with that in oxyfluoride glass ceramics in this system. With the advantages of excellent transparence, easy shaping, good stability, and low cost, $hbox{Yb}^{3+}hbox{–}hbox{Tb}^{3+}$ codoped borosilicate glasses are potentially used as down-converter layer in silicon-based solar cells.      

Multiwavelength $Q$-switched Laser by Incorporating a LiNbO$_{3}$ Phase Modulator in Fabry–PÉrot Cavity

In this letter, we present a simple and compact laser cavity that can be used for $Q$-switching and multiwavelength oscillation. It is shown that a LiNbO $_{3}$ phase modulator with relatively low driven voltage inserted into a Fabry–PÉrot cavity can act simultaneously as an effective component for suppressing the homogeneous line broadening, switching the $Q$ -value of the laser cavity, and a polarizer. Multiwavelength operation of Yb-doped fiber laser is achieved by phase modulation. $Q$-switching is achieved due to the residual intensity modulation of the phase modulator, and the pulse performance is also impacted by the phase modulation amplitude. Three stable wavelengths with identical wavelength spacing of 3.3 nm and pulsed laser of 0.2 $mu$J per pulse energy at the repetition rate of 55.8 kHz are demonstrated. The full-width at half-maximum pulse duration is of 2 $mu$s, and the polarization extinction ratio is $>$23 dB.