Processing and Mechanical Behavior of CrN/ZrO2(2Y) Composites

CrN powder consisting of granular particles of ∼3 μm has been prepared by self-propagating high-temperature synthesis under a nitrogen pressure of 12 MPa using Cr metal. Dense pure CrN ceramics and CrN/ZrO₂(2Y) composites in the CrN-rich region have been fabricated by hot isostatic pressing for 2 h at 1300°C and 196 MPa. The former ceramics have a fracture toughness ( K _IC) of 3.3 MPa ·m^1/2 and a bending strength (σ_b) of 400 MPa. In the latter materials almost all of the ZrO₂(2Y) grains (0.36–0.41 μm) are located in the grain boundaries of CrN (∼4.6 μm). The values of K _IC (6.1 MPa · m^1/2) and σ_b (1070 MPa) are obtained in the composites containing 50 vol% ZrO₂(2Y).     

Mechanical Properties of CoAl Materials with the Combined Additions of ZrO2(3Y) and Al2O3

Intermetallic CoAl powder has been prepared via self-propagating high-temperature synthesis (SHS). Dense CoAl materials (99.6% of theoretical) with the combined additions of ZrO₂(3Y) and Al₂O₃ have been fabricated via spark plasma sintering (SPS) for 10 min at 1300°C and 30 MPa. The microstructures are such that tetragonal ZrO₂ (0.3 μm) and Al₂O₃ (0.5 μm) particles are located at the grain boundaries of the CoAl (8.5 μm) matrix. Improved mechanical properties are obtained; especially the fracture toughness and the bending strength of the materials with ZrO₂(3Y)/Al₂O₃= 16/4 mol% are 3.87 MPa·m^1/2 and 1080 MPa, respectively, and high strength (>600 MPa) can be retained up to 1000°C.     

Influence of ZrO2 Grain Size and Content on the Transformation Response in the Al2O3─ZrO2 (12 mol% CeO2) System

Based on experimental and modeling studies, the rate of increase in the martensite start temperature M _s for the tetragonal-to-monoclinic transformation with increase in zirconia grain size is found to rise with decrease in ZrO₂ content in the zirconia-toughened alumina ZTA system. The observed grain size dependence of M _s can be related to the thermal expansion mismatch tensile (internal) stresses which increase with decrease in zirconia content. The result is that finer zirconia grain sizes are required to retain the tetragonal phase as less zirconia is incorporated into the alumina, in agreement with the experimental observations. At the same time, both the predicted and observed applied stress required to induce the transformation are reduced with increase in the ZrO₂ grain size. In addition, the transformation-toughening contribution at temperature T increases with increase in the M _s temperature brought about by the increase in the ZrO₂ grain size, when T > M _s. In alumina containing 20 vol% ZrO₂ (12 mol% CeO₂), a toughness of ∼10 MPa. √m can be achieved for a ZrO₂ grain size of ∼2 μm ( M _s∼ 225 K). However, at a grain size of ∼2 μm, the alumina–40 vol% ZrO₂ (12 mol% CeO₂) has a toughness of only 8.5 MPa. √m ( M _s∼ 150 K) but reaches 12.3 MPa. ∼m ( M _s∼ 260 K) at a grain size of ∼3 μm. These findings show that composition (and matrix properties) play critical roles in determining the ZrO₂ grain size to optimize the transformation toughening in ZrO₂-toughened ceramics.     

Stability of Ultrafine Tetragonal ZrO2 Coprecipitated with Al2O3 by the Spray-ICP Technique

The transformation of ultrafine powders (particle size, 0.01 to 0.04 μm) of the system ZrO_2–Al₂O₃, prepared by spraying their corresponding nitrate solutions into an inductively coupled plasma (ICP) of ultrahigh temperature, was investigated. The powders were composed of metastable tetragonal ZrO₂ ( mt- ZrO₂) and γ-Al₂O₃. On heating, the mt- ZrO₂ (or tetragonal ZrO₂, t -ZrO₂) was retained up to 1200°C. At 1380°C the transformation to monoclinic ZrO₂ ( m -ZrO₂) occurred and the amount of the m -ZrO₂ decreased with the increase in Al₂O₃ content, thus indicating the stabilization of the t -ZrO₂ by the Al₂O₃, which seems to be explained in terms of the retardation of grain growth.     

Toughening and Strengthening of NiAl with Al2O3 by the Addition of ZrO2(3Y)

NiAl/10-mol%-ZrO₂(3Y) composites of almost full density have been fabricated via spark plasma sintering (SPS) for 10 min at 1300°C and 30 MPa. The former intermetallic compound, which contains a trace amount of Al₂O₃, has been prepared via self-propagating high-temperature synthesis. The composite microstructures are such that tetragonal ZrO₂ (∼0.2 μm) and Al₂O₃ (∼0.5 μm) particles are located at the grain boundaries of the NiAl (∼46 μm) matrix. Improved mechanical properties are obtained: the fracture toughness and bending strength are 8.8 MPa·m^1/2 and 1045 MPa, respectively, and high strength (>800 MPa) can be retained up to 800°C.     

Fracture Strength–Fracture Resistance Response and Damage Resistance of Sintered Al2O3–ZrO2 (12 mol% CeO2) Composites

The fracture strengths of sintered Al₂O₃ containing 20 and 40 vol% ZrO₂(12 mol% CeO₂)—zirconia-toughened alumina (ZTA)—composites along with the fracture resistance can be increased (e.g., to ∼900 MPa and >12 Mpa·m^1/2, respectively), by increasing the mean grain size of the t -ZrO₂ (and the Al₂O₃) from ∼0.5 μm to ∼3 μm. At these lower t -ZrO₂ contents, the fracture strength-fracture resistance curves show a continuous rise as opposed to the strength maxima observed in polycrystalline t -ZrO₂(12 mol% CeO₂), CeTZP, and ZrO₂(12 mol% CeO₂) ceramics containing ≤20 vol% Al₂O₃. The toughened composites also exhibit excellent damage resistance with fracture strengths of 500 MPa retained with surfaces containing ∼150- N Vickers indentations which produce cracks of ∼160-μm radius. Greater damage resistance correlates with an increase in the apparent R -curve response of these composites.     

Slow Crack Growth Behavior in Transformation-Toughened Al2O3-ZrO2(Y2O3) Ceramics

Significant increases in the critical fracture toughness (K _IC ) over that of alumina are obtained by the stress-induced phase transformation in partially stabilized ZrO₂ particles which are dispersed in alumina. More importantly, improved slow crack growth resistance is observed in the alumina ceramics containing partially stabilized ZrO₂ particles when the stress-induced phase transformation occurs. Thus, increasing the contribution of the ZrO₂ phase transformation by tailoring the Y₂O₃ stabilizer content not only increases the critical fracture toughness (K_IC) but also the K _Ia to initiate slow crack growth. For example, crack velocities ( v )≥10^–9 m/s are obtained only at K _Ia≥5 MPa.m^1/2 in transformation-toughened ( K _IC=8.5 MPa.m^1/2) composites vs K _Ia≥2.7 MPa.m^1/2 for comparable velocities in composites where the transformation does not occur ( K _IC=4.5 MPa.m^1/2). This behavior is a result of crack-tip shielding by the dissipation of strain energy in the transformation zone surrounding the crack. The stress corrosion parameter n is lower and A greater in these fine-grained composite materials than in fine-grained aluminas. This is a result of the residual tensile stresses associated with larger (≥1 μm) monoclinic ZrO₂ particles which reside along the intergranular crack path.     

Low-Temperature Sintering of Seeded Sol—Gel-Derived, ZrO2-Toughened Al2O3 Composites

Seeding a mixture of boehmite (AIOOH) and colloidal ZrO₂ with α-alumina particles and sintering at 1400°C for 100 min results in 98% density. The low sintering temperature, relative to conventional powder processing, is a result of the small alumina particle size (∼0.3 μm) obtained during the θ-to α-alumina transformation, homogeneous mixing, and the uniform structure of the sol-gel system. Complete retention of pure ZrO₂ in the tetragonal phase was obtained to 14 vol% ZTA because of the low-temperature sintering. The critical grain size for tetragonal ZrO₂ was determined to be ∼0.4 μm for the 14 vol% ZrO₂—Al₂O₃ composite. From these results it is proposed that seeded boehmite gels offer significant advantages for process control and alumina matrix composite fabrication.     

Chemical Interactions Promoting the ZrO2 Tetragonal Stabilization in ZrO2–SiO2 Binary Oxides

Metastable tetragonal ZrO₂ phase has been observed in ZrO₂–SiO₂ binary oxides prepared by the sol–gel method. There are many studies concerning the causes of ZrO₂ tetragonal stabilization in binary oxides such as Y₃O₂–ZrO₂, MgO–ZrO₂, or CaO–ZrO₂. In these binary oxides, oxygen vacancies cause changes or defects in the ZrO₂ lattice parameters, which are responsible for tetragonal stabilization. Since oxygen vacancies are not expected in ZrO₂–SiO₂ binary oxides, tetragonal stabilization should just be due to the difficulty of zirconia particles growing in the silica matrix. Furthermore, changes in the tetragonal ZrO₂ crystalline lattice parameters of these binary oxides have recently been reported in a previous paper. The changes of the zirconia crystalline lattice parameters must result from the chemical interactions at the silica–zirconia interface (e.g., formation of Si–O–Zr bonds or Si–O⁻ groups). In this paper, FT-IR and ²⁹Si NMR spectroscopy have been used to elucidate whether the presence of Si–O–Zr or Si–O⁻ is responsible for tetragonal phase stabilization. Moreover, X-ray diffraction, Raman spectroscopy, and transmission electron microscopy have also been used to study the crystalline characteristics of the samples.     

A Novel Method for Fabrication of Y2O3-Stabilized ZrO2 Electrolyte Films

Gas-tight Y₂O₃-stabilized ZrO₂ (YSZ) films were prepared on NiO–YSZ and NiO–SDC (Sm_0.2Ce_0.8O_1.9) anode substrates by a novel method. A cell, Ni–YSZ/YSZ(10 μm)/LSM–YSZ, was tested with humidified hydrogen as fuel and ambient air as oxidant. The maximum power densities of 1.64, 1.40, 1.06, and 0.60 W/cm² were obtained at 850°, 800°, 750°, and 700°C, respectively. With methane as fuel, a cell of Ni–SDC/YSZ (12 μm)/LSM–YSZ exhibited the maximum power densities of 1.14, 0.82, 0.49, and 0.28 W/cm² at 850°, 800°, 750°, and 700°C, respectively. The impedance results showed that the performance of the cell was controlled by the electrode polarization rather than the resistance of YSZ electrolyte film.     

Transformation Toughening in Large-Grain-Size CeO2-Doped ZrO2 Polycrystals

The fracture and transformation behavior of tetragonal polycrystalline ZrO₂ alloys containing 18 mol% CeO₂ (Ce-TZP) was investigated. In the absence of applied stress the tetragonal phase was found to be stable in large-grained (>30 μm) samples at room temperature. The monoclinic phase was detected in regions of high residual stress near hardness indentations although no evidence of a wake of monoclinic phase along the fracture surface was observed. The fracture toughness increased from 4 to 7 MPa · m^1/2 as density and/or grain size increased. It is proposed that the relatively high toughness of these materials is due to the occurrence of stress-driven tetragonal-to-monoclinic transformation near the crack tip, which reverses when the crack has passed.     

Creep of CaO-Stabilized ZrO2

The compressive creep of 18 mol% CaO-stabilized ZrO₂ was studied at 1200° to 1400°C and 500 to 4000 psi. The specimens were polycrystalline with grain diameters from 7 to 29 μm. The activation energy for creep is 94 kcal/mol, and the creep rates are linearly proportional to the stress and to the inverse of the grain size. These results lead to the conclusion that creep in 18 mol% CaO-stabilized ZrO₂ may be controlled by cation diffusion associated with grain-boundary sliding.     

Room-Temperature Strength and Fracture of ZrO2-Y2O3 Single Crystals

Strength and fracture toughness results are presented for ZrO₂ single crystals stabilized with Y₂O₃. The crystals (2 cm in diameter by 5 cm long) were prepared by skull melting. The partially stabilized compositions with 4 to 6 wt% Y₂O₃ showed a dramatic improvement in mechanical properties over the fully stabilized samples containing 20 wt% Y₂O₃, i.e. a strength exceeding 1000 MPa and a fracture toughness of 8 Mpa,.m ^1/2 were achieved compared to 200 MPa and 2 Mpa.m^1/2, respectively, for fully stabilized ZrO₂ single crystals.     

High-Toughness Ce-TZP/Al2O3 Ceramics with Improved Hardness and Strength

Simulataneous additions of SrO and Al₂O₃ to ZrO₂ (12 mol% CeO₂) lead to the in situ formation of strontium aluminate (SrO · 6Al₂O₃) platelets (∼0.5 μm in width and 5 to 10 μm in length) within the Ce-TZP matrix. These platelet-containing Ce-TZP ceramics have the strength (500 to 700 MPa) and hardness (13 to 14 GPa) of Ce-TZP/Al₂O₃ while maintaining the high toughness (14 to 15 MPa ± m^1/2) of Ce-TZP. Optimum room-temperature properties are obtained at SrO/Al₂O₃ molar ratios between 0.025 and 0.1 for ZrO₂ (12 mol% CeO₂) with starting Al₂O₃ contents ranging between 15 and 60 vol%. The role of various toughening mechanisms is discussed for these composite ceramics.     

Low-Temperature Equilibria Among ZrO2, Tho2, and UO2

Studies made on low-hafnium-content ZrO₂, show that the monoclinic-tetragonal inversion temperature is 1170°C., and it is raised to approximately 1190°C. in the "natural" ZrO², which contains approximately 2% HfO₂. No explanation could be found for the knownmarked hysteresis during cooling, when the reverse polymorphic transformation takes dace at 1040°C. In the system ZrO₂-ThO₂ the monoclinic-tetragonal ZrO₂, inversion temperature is lowered to 1000°C., although the maximum solid solution extent of ZrO₂, in Thon and vice versa is approximately only 2% at this temperature. Below about 400°C. under hydrothermal conditions it was possible to prepare a continuous, although metastable series of solid solutions with the fluorite structurewith compositions varying from ThO₂, to nearly pure ZrO₂. Contrary to earlier work only 8 mole ZrO₂, dissolves in UO₂ and less than 4 mole of UO, in ZrO₂ at temperatures up to 13OO0C. A continuous series of solid solutions could be made between Th₂ and UO₂ at 13OO°C., and extensive defect fluorite solid solutions could be prepared between Tho₂ and U₃O₈; there is some evidence for exsolution into uranium-rich and thorium-rich members at low temperatures.     

Formation, Characterization, and Hot Isostatic Pressing of Cr2O3-Doped ZrO2 (0,3 mol% Y2O3) Prepared by Hydrazine Method

In the ZrO₂-Cr₂O₃ system, metastable t -ZrO₂ solid solutions containing up to 11 mol% Cr₂O₃ crystallize at low temperatures from amorphous materials prepared by the hydrazine method. The lattice parameter c decreases linearly from 0.5149 to 0.5077 nm with increased Cr₂O₃ content, whereas the lattice parameter a is a constant value ( a = 0.5077 nm) regardless of the starting composition. At higher temperatures, transformation (decomposition) of the solid solutions proceeds in the following way: t (ss)→ t (ss) + m + Cr₂O₃→ m + Cr₂O₃. Above 11 mol% Cr₂O₃ addition, c-ZrO₂ phases are formed in the presence of Cr₂O₃. The t -ZrO₂ solid solution powders have been characterized for particle size, shape, and surface area. They consist of very fine particles (15–30 nm) showing thin platelike morphology. Dense ZrO₂(3Y)-Cr₂O₃ composite ceramics (∼99.7% of theoretical) with an average grain size of 0.3 μm have been fabricated by hot isostatic pressing for 2 h at 1400°C and 196 MPa. Their fracture toughness increases with increased Cr₂O₃ content. The highest K _Ic value of 9.5 MPa·;m^1/2 is achieved in the composite ceramics containing 10 mol% Cr₂O₃.     

Load Dependence of Hardness in Sintered Submicrometer Al2O3 and ZrO2

Monolithic alumina bodies with a grain size of 0.5 μm and submicrometer tetragonal ZrO₂ (3 mol% Y₂O₃) polycrystals were produced and investigated. With decreasing indentation load, the hardness increases but may again decrease below about 5 N; relevant measurements require the application of fairly high loads. Decreasing grain sizes increase the hardness of alumina and zirconia ceramics even for very small grain sizes in the submicrometer range.     

Phase Stability and Physical Properties of Cubic and Tetragonal ZrO2 in the System ZrO2–Y2O3–Ta2O5

The cubic ( c -ZrO₂) and tetragonal zirconia ( t -ZrO₂) phase stability regions in the system ZrO₂–Y₂O₃–Ta₂O₅ were delineated. The c -ZrO₂ solid solutions are formed with the fluorite structure. The t -ZrO₂ solid solutions having a c/a axial ratio (tetragonality) smaller than 1.0203 display high fracture toughness (5 to 14 MPa · m^1/2), and their instability/transformability to monoclinic zirconia ( m -ZrO₂) increases with increasing tetragonality. On the other hand, the t -ZrO₂ solid solutions stabilized at room temperature with tetragonality greater than 1.0203 have low toughness values (2 to 5 MPa · m^1/2), and their transformability is not related to the tetragonality.     

Fabrication and Characterization of Three-Dimensional ZrO2-Toughened Al2O3 Ceramic Microdevices

Dense three-dimensional (3D) microdevices of ZrO₂-toughened Al₂O₃ (ZTA) were fabricated using microstereolithography and a subsequent sintering process. Using microstereolithography, 3D green bodies could be formed from a 40 vol% ZTA ceramic–resin paste. After sintering, the fabricated 3D devices are converted into dense ceramic devices without deformation. In this study, a gear (with a tooth edge of 25 μm) and a photonic crystal (with a lattice constant of 500 μm) were designed and fabricated. The dimensional accuracy of the fabrication process is within 20 μm and the sintering shrinkage is around 26% for these microdevices. The relative density of the sintered ZTA ceramics reached 96.5% of theoretical value. The measured hardness and toughness were about 14 GPa and 11 MPa m^1/2, respectively, in both the top and side surfaces. A band gap between 320 and 420 GHz was observed in the ZTA photonic crystal. The microstereolithography process can be easily applied to other ceramic materials and devices.     

Transient Thermal Stress Behavior in ZrO2-Toughened Al2O3

The initial strength of (σ_i) and thermal shock resistances (Δ T_c and σ_r/σ_i), as determined by quench tests, of Al₂O₃-ZrO₂ composites are increased by increasing amounts of tetragonal ZrO₂ second phase for contents of up to ∼15 vol%. For composites with ≤9 vol% ZrO₂ the increases in σ_r and Δ T_c reflect the increase in γ_IC with addition of ZrO₂ However, for ZrO₂contents >9 vol%, the thermal shock resistances (Δ T_c and σ_r/σ_i) and σ_i are also affected by machining-induced microcracking in the surface of the samples. For ZrO₂ contents >14 vol%, bulk microcracking can become extensive and result in a degradation of σ_i and Δ T_c .