Dissolving and stabilizing soft WB2 and MoB2 phases into high-entropy borides via boron-metals reactive sintering to attain higher hardness

Five single-phase WB₂- and MoB₂-containing high-entropy borides (HEBs) have been made via reactive spark plasma sintering of elemental boron and metals. A large reactive driving force enables the full dissolution of 10−20 mol. % WB₂ to form dense, single-phase HEBs, including (Ti_0.2Zr_0.2Hf_0.2Mo_0.2W_0.2)B₂, (Ti_0.2Ta_0.2Cr_0.2Mo_0.2W_0.2)B₂, (Zr_0.2Hf_0.2Nb_0.2Ta_0.2W_0.2)B₂, and (Zr_0.225Hf_0.225Ta_0.225Mo_0.225W_0.1)B₂; the successful fabrication of such single-phase WB₂-containing HEBs has not been reported before. In the processing science, this result serves perhaps the best example demonstrating that the phase formation in high-entropy ceramics can strongly depend on the kinetic route. A scientifically interesting finding is that HEBs containing softer WB₂ and/or MoB₂ components are significantly harder than (Ti_0.2Zr_0.2Hf_0.2Nb_0.2Ta_0.2)B₂ (with harder binary boride components). This exemplifies that high-entropy ceramics can achieve unexpected properties.     

Ultra high temperature high-entropy borides: Effect of graphite addition on oxides removal and densification behaviour

The introduction of 0.5–1.0 wt.% graphite to the powders prepared by Self-propagating High-temperature Synthesis (SHS) is found to be highly beneficial for the removal of oxide impurities (from 2.7-8.8 wt.% to 0.2–0.5 wt.%) during spark plasma sintering (1950°C/20 min, 20 MPa) of (Hf_0.2Mo_0.2Ta_0.2Nb_0.2Ti_0.2)B₂ and (Hf_0.2Mo_0.2Ta_0.2Zr_0.2Ti_0.2)B₂ ceramics. Concurrently, the consolidation level achieved is enhanced from about 92.5% and 88%, respectively, to values exceeding 97%. While a further increase of graphite slightly improves samples densification, final products become progressively richer of the unreacted carbon.It is assumed that graphite plays a double role during SPS, e.g. not only as a reactant during the carbothermal reduction of oxides contaminant, but also as lubricating agent for the powder particles. The latter phenomenon is likely the main responsible for the densification improvement when 3 wt.% or larger amounts of additive are used. Another positive effect is the crystallite size refinement of the high-entropy phases with the progressive abatement of oxides, to confirm that their presence promotes grain coarsening during the sintering process.     

Microstructure and mechanical properties of high-entropy borides derived from boro/carbothermal reduction

Starting from metal oxides, B₄C and graphite, a suite of high-entropy boride ceramics, formulated (Hf_0.2Zr_0.2Ta_0.2Nb_0.2Ti_0.2)B₂, (Hf_0.2Zr_0.2Mo_0.2Nb_0.2Ti_0.2)B₂ and (Hf_0.2Mo_0.2Ta_0.2Nb_0.2Ti_0.2)B₂ derived from boro/carbothermal reduction at 1600 °C were fabricated by spark plasma sintering at 2000 °C. It was found that the synthetic high-entropy boride crystalized in hexagonal structure and the yield of the targeting phase was calculated to be over 93.0 wt% in the sintered ceramics. Benefitting from the nearly full densification (96.3% ˜ 98.5% in relative density) and the refined microstructure, the products exhibited the relatively high Vickers hardness. The indentation fracture toughness was determined to be comparable with the single transition metal-diboride ceramics. It should be noted that the formation of high-entropy boride ceramics were featured with the relatively high hardness at no expense of the fracture toughness.     

Synthesis of single-phase high-entropy diboride powders and their spheroidization process

Spherical (Zr_.2Ti_.2Ta_.2Nb_.2Mo_.2)B₂ powders with a uniform particle size distribution are successfully prepared using a novel industrial approach, which combines spray-drying process and thermal plasma sintering technology together. In this, single-phase (Zr_.2Ti_.2Ta_.2Nb_.2Mo_.2)B₂ powders are first synthesized via a borothermal reduction process using a mixture of individual metallic oxides and boron powders as starting materials. The influence of boron powder content on the structure of prepared powders is researched. Then, (Zr_.2Ti_.2Ta_.2Nb_.2Mo_.2)B₂ granules are prepared after wet-grinding and spray-drying process, which exhibit a spherical shape and homogeneous element distribution. RF induction thermal plasma is finally used to sinter the granulated particle, and the apparent density of sintered spherical powders is increased to 2.57 g/cm³ from 1.43 g/cm³. Such powders are in potential demand for additive manufacturing techniques, and the successful synthesis of spherical (Zr_.2Ti_.2Ta_.2Nb_.2Mo_.2)B₂ powders may guide the way toward the preparation of many other spherical high-entropy diboride powders.     

Microstructures and oxidation mechanisms of (Zr0.2Hf0.2Ta0.2Nb0.2Ti0.2)B2 high-entropy ceramic

A nano dual-phase powder with great sinterability was synthesized by molten-salt assisted borothermal reductions at 1100 °C using B, ZrO₂, HfO₂, Ta₂O₅, Nb₂O₅ and TiO₂ powders as raw materials. Single-phase (Z_r0.2Hf_0.2Ta_0.2Nb_0.2Ti_0.2)B₂ high-entropy ceramic was prepared by spark plasma sintering using the as-synthesized nano dual-phase powder. Oxidation behavior of the (Zr_0.2Hf_0.2Ta_0.2Nb_0.2Ti_0.2)B₂ ceramic was investigated over the range of 30–1400 °C in air and the result indicated that the rapid oxidation of ceramic began at 1300 °C. The phenomenon could be ascribed to the rapid volatilization of B₂O₃ from oxide scale. A layered structure was formed at the cross section of (Zr_0.2Hf_0.2Ta_0.2Nb_0.2Ti_0.2)B₂ ceramic after oxidation. The relationship between partial pressures of gaseous metal oxides and oxygen partial pressures was calculated, which inferred that the formation of layered structure could be ascribed to the active oxidation of (Zr_0.2Hf_0.2Ta_0.2Nb_0.2Ti_0.2)B₂, the generation of gaseous metal oxides, their outward diffusion and further oxidation.     

Fine-grained dual-phase high-entropy ceramics derived from boro/carbothermal reduction

In the current work, fine-grained dual-phase, high-entropy ceramics (Ti_0.2Zr_0.2Hf_0.2Nb_0.2Ta_0.2)B₂-(Ti_0.2Zr_0.2Hf_0.2Nb_0.2Ta_0.2)C with different phase ratios were prepared from powders synthesized via a boro/carbothermal reduction approach, by adjusting the content of B₄C and C in the precursor powders. Phase compositions, densification, microstructure, and mechanical properties were investigated and correlated. Due to the combination of pinning effect and the boro/carbothermal reduction approach, the average grain size (～0.5?1.5 μm) of the dual-phase high-entropy ceramics was roughly one order of magnitude smaller than previously reported literature. The dual-phase high-entropy ceramics had residual porosity ranging from 0.3 to 3.2 % upon sintering by SPS and the material with about 18 vol% boride phase exhibited the highest Vickers hardness (24.2±0.3 GPa) and fracture toughness (3.19±0.24 MPam^1/2).     

Low-temperature synthesis of high-entropy (Hf0.2Ti0.2Mo0.2Ta0.2Nb0.2)B2 powders combined with theoretical forecast of its elastic and thermal properties

A theoretical calculation combined with experiment was used to study high-entropy (Hf_0.2Ti_0.2Mo_0.2Ta_0.2Nb_0.2)B₂ (HEB-HfTiMoTaNb). The theoretical calculation suggested HEB-HfTiMoTaNb could be stable over a wide temperature range. Then, a novel solvothermal/molten salt-assisted borothermal reduction method was proposed to efficiently pre-disperse transitional metal atoms in a precursor and synthesize (Hf_0.2Ti_0.2Mo_0.2Ta_0.2Nb_0.2)B₂ nanoscale powders at 1573 K for 6 h, which is nearly 300 K lower than previous reports. The characterization results indicated that the as-synthesized nanoscale HEB-HfTiMoTaNb powder was hexagonal single-phase with homogeneous elements distribution and uniform size, and the oxygen content of the particles is 0.97 wt%. Simultaneously, the mechanical properties, anisotropic nature, and thermal properties of HEB-HfTiMoTaNb were investigated by density functional theory (DFT) calculations. The Cannikin's law was adopted to explain the improvement of comprehensive mechanical properties. In addition, a significant reduction of thermal conductivity was observed for HEB-HfTiMoTaNb and it only was 1/15 of the value of HfB₂. This work suggests a reliable technique for synthesis of nanosized HEB powders and discovery of high-entropy materials under the guidance of first-principle theory.     

Hardness and toughness improvement of SiC-based ceramics with the addition of (Hf0.2Mo0.2Ta0.2Nb0.2Ti0.2)B2

The influences of different contents ranging 0–15 wt% of high-entropy boride (HEB) (Hf_0.2Mo_0.2Ta_0.2Nb_0.2Ti_0.2)B₂ on the mechanical properties of SiC-based ceramics using Al₂O₃-Y₂O₃ sintering additives sintered by spark plasma sintering process were investigated in this study. The results showed that the introduction of 5 and 10 wt% (Hf_0.2Mo_0.2Ta_0.2Nb_0.2Ti_0.2)B₂ could facilitate the densification and the grain growth of SiC-based ceramics via the mechanism of liquid phase sintering. However, the grain growth of SiC-based ceramics was inhibited by the grain boundary pinning effect with the addition of 15 wt% (Hf_0.2Mo_0.2Ta_0.2Nb_0.2Ti_0.2)B₂. The SiC-based ceramics with 15 wt% (Hf_0.2Mo_0.2Ta_0.2Nb_0.2Ti_0.2)B₂ showed the enhanced hardness (21.9±0.7 GPa) and high toughness (4.88±0.88 MPa·m^1/2) as compared with high-entropy phase-free SiC-based ceramics, which exhibited a hardness of 16.6 GPa and toughness of 3.10 MPa·m^1/2. The enhancement in mechanical properties was attributed to the addition of higher hardness of HEB phase, crack deflection toughening mechanism, and presence of residual stress due to the mismatch of coefficient of thermal expansion.     

Synthesis and thermal stability of novel high-entropy metal boron carbonitride ceramic powders

High-entropy metal boron carbonitride ceramic powders including (Ta_0.2Nb_0.2Zr_0.2Hf_0.2W_0.2)BCN, (Ta_0.2Nb_0.2Zr_0.2Hf_0.2Ti_0.2)BCN, and (Ta_0.2Nb_0.2Zr_0.2Ti_0.2W_0.2)BCN, were successfully synthesized via mechanical alloying at room temperature. Results show that for the first step of 10 h milling, the amorphous BCN phases are observed. After 24 h of second step milling, the as-synthesized high-entropy ceramics exhibit a single face-centered cubic solid solution structure with high compositional uniformity from nano-scale to micron-scale. When heated to 1500 °C for 30min in flowing Ar, the as-prepared high-entropy ceramic powders still show relatively high thermal stability; however, some metals oxides like HfO₂ and ZrO₂ are detected due to the pre-existing oxides on sample surfaces. After heat treatment, some amorphous phases are still retained. This work suggests a new processing route on the synthesis of high-entropy metal boron carbonitride ceramics.     

On the phase and grain boundaries in dual phase carbide/boride ceramics from micro to atomic level

The phase and grain boundary characteristics of recently developed fine-grained dual-phase high-entropy (Ti-Zr-Nb-Hf-Ta)C/(Ti-Zr-Nb-Hf-Ta)B₂ was investigated throughout all the accessible length scales using scanning electron microscopy (SEM), aberration-corrected scanning transmission electron microscopy (STEM), energy dispersive X-ray spectroscopy (EDS) and electron energy loss spectroscopy (EELS). The system exhibits relatively homogeneous grain size distribution where the average size is approximately 0.97 µm, with chemical composition (Ti_0.14 Zr_0.2 Nb_0.2 Hf_0.2 Ta_0.26)C + (Ti_0.38 Zr_0.18 Nb_0.22 Hf₀.₁₁₅ Ta_0.105)B₂. SEM analyses revealed no micro-crack formation and second – phase segregation at the boundaries or micro-pores at the triple – points. Investigation down to the sub-nanometer scale revealed that the phase and grain boundaries were typically clean and sharp with an indistinct 1 – 1.5 nm thin gradient of metallic elements at boride/boride and carbide/carbide interfaces. The sharp phase and grain boundaries do exhibit elemental enrichment from a trace amount of Fe being incorporated in interstitial positions of carbide and boride grains locally at boride/carbide boundaries or are present in boride and carbide grains in the form of continuous thin layer at boride/boride and carbide/carbide interfaces with the probably origin from starting powders.