Electrochemical corrosion characteristics of ZrNi5−xCox alloys

The electrochemical corrosion behaviour of a series of ZrNi_5−xCo_x alloys with x=0-4 has been tested using potentiokinetic polarisation technique. The polarisation curves were measured in deaerated 0.5 M sulphate solutions with pH=0.2-7 and in strong alkaline solution of KOH (pH=15). It is shown that the presence of greater amounts of Co in the alloy (x?2) worsens the passivating properties of the alloy in acidified sulphate solutions. On the other hand, in strong alkaline solutions, both low- and high-cobalt alloys undergo stable passivation. The degree of Ni substitution by Co in the alloys does not generally affect the shape of cathodic polarisation curves.     

Corrosion behavior of three iron-based model alloys in reducing atmospheres containing HCl and H2S at 600 °C

The corrosion of three Fe-xCr alloys (x = 8, 12, 18 wt.%) was examined at 600 °C in reducing atmospheres containing HCl and H₂S with two different H₂S contents and compared with the behavior of the same materials in H₂S-free H₂-CO₂ and H₂-HCl-CO₂ mixtures producing similar oxygen and chlorine pressures. Exposure to the low-H₂S gas mixture had only a reduced effect on the behavior of Fe-8Cr and Fe-18Cr, but increased significantly the corrosion rate of Fe-12Cr. Increasing the H₂S level accelerated the corrosion of all the alloys, but particularly that of Fe-18Cr. In both cases only minor amounts of sulfur and chlorine were present close to the alloy/scale interface. An increase of the Cr content reduced the corrosion rate in both H₂S gas mixtures, especially in the range 8-12 wt.% Cr, due to a larger volume fraction of Cr₂O₃ in the scale. The results have been discussed on the basis of the thermodynamic stability diagrams of the Fe-O-Cl-S and Cr-O-Cl-S systems.     

Corrosion behaviour of magnesium/aluminium alloys in 3.5 wt.% NaCl

Corrosion behaviour of commercial magnesium/aluminium alloys (AZ31, AZ80 and AZ91D) was investigated by electrochemical and gravimetric tests in 3.5 wt.% NaCl at 25 °C. Corrosion products were analysed by scanning electron microscopy, energy dispersive X-ray analysis and low-angle X-ray diffraction. Corrosion damage was mainly caused by formation of a Mg(OH)₂ corrosion layer. AZ80 and AZ91D alloys revealed the highest corrosion resistance. The relatively fine β-phase (Mg₁₇Al₁₂) network and the aluminium enrichment produced on the corroded surface were the key factors limiting progression of the corrosion attack. Preferential attack was located at the matrix/β-phase and matrix/MnAl intermetallic compounds interfaces.     

Corrosion behaviour of magnetron-sputtered Al1−x-Mnx coatings in neutral saline solution

Al-Mn coatings with different contents (0-41 at.%) were deposited on glass slides by magnetron co-sputtering. These coatings were characterised, before and after immersion tests, by X-ray diffraction, scanning electron microscopy (SEM) and electron probe microanalysis. The electrochemical measurements in a neutral saline solution showed that the pitting corrosion resistance of Al-Mn coatings increased with increasing Mn content as the pitting corrosion potentials are progressively shifted towards positive values. The immersion tests reveal that for all Mn contents, Al-Mn coatings keep a sacrificial character compared with steel. For Mn content above 26 at.%, XRD analysis showed the formation of an amorphous phase. This structure would be responsible for the high increase of the hardness of Al-Mn coatings and of the stabilisation of their open circuit potentials during the 48 h immersion tests.     

The effect of molybdenum on the corrosion behaviour of the high-entropy alloys Co1.5CrFeNi1.5Ti0.5Mox in aqueous environments

The purpose of this study is to investigate the electrochemical properties of the Co_1.5CrFeNi_1.5Ti_0.5Mo_x high-entropy alloys in three aqueous environments which simulate acidic, marine, and basic environments at ambient temperature (∼25 °C). The potentiodynamic polarisation curves of the Co_1.5CrFeNi_1.5Ti_0.5Mo_x alloys, obtained in aqueous solutions of H₂SO₄ and NaOH, clearly revealed that the corrosion resistance of the Mo-free alloy was superior to that of the Mo-containing alloys. On the other hand, the lack of hysteresis in cyclic polarisation tests and SEM micrographs confirmed that the Mo-containing alloys are not susceptible to pitting corrosion in NaCl solution.     

MOCVD growth and characterizations of BxAl1−xAs and BxAl1−x−yInyAs alloys

Zinc-blende B_xAl_1−xAs and B_xAl_1−x−yIn_yAs alloys have been grown on exactly oriented (0 0 1)GaAs substrates by low pressure metalorganic chemical vapor deposition (LP-MOCVD). The influence of susceptor coating, growth temperature and gas-phase boron mole fraction on boron incorporation into AlAs has been comprehensively investigated. It has been found that boron incorporation into AlAs could be enhanced and the optimal growth temperature range of B_xAl_1−xAs alloys changed from 580 °C to 610 °C when SiC-coated graphite susceptors were replaced by the non-coated ones. In this study, the maximum boron composition x of 2.8% was achieved for the pseudomorphically strained B_xAl_1−xAs alloys. AFM measurements show that RMS roughness of B_xAl_1−xAs alloys increased sharply with the increase of gas-phase boron mole fraction. Raman spectra of B_xAl_1−xAs alloys show a linear increase of the BAs shift with boron composition x. Based on BAlAs deposition, bulk B_xAl_1−x−yIn_yAs (x = 1.9%) quaternary alloy was grown lattice-matched to GaAs successfully. Moreover, 10-period BAlAs/GaAs and BAlInAs/GaAs MQW heterostructures were also demonstrated.     

Electrochemical hydrogen storage properties of non-stoichiometric La0.7Mg0.3−xCaxNi2.8Co0.5 (x = 0-0.10) electrode alloys

The microstructure and electrochemical hydrogen storage characteristics of La_0.7Mg_0.3−xCa_xNi_2.8Co_0.5 (x = 0, 0.05 and 0.10) alloys prepared by arc-melting and subsequent powder sintering method are investigated. The electrochemical measurement results show that the cycle stability after 100 charge/discharge cycles first increases from 46.4% (x = 0) to 54.3% (x = 0.05), then decreases to 43.2% (x = 0.10), and the high rate dischargeability increases from 64.5% (x = 0) to 68.5% (x = 0.10) at the discharge current density of 1200 mA/g. The electrochemical impedance spectroscopy analysis indicates that the electrochemical kinetics of the alloy electrodes is improved by increasing Ca. The entire results exhibit that a suitable content of Ca (x = 0.05) can improve the overall electrochemical hydrogen storage characteristics of the alloys.     

Effect of the aluminium content of AlxCrFe1.5MnNi0.5 high-entropy alloys on the corrosion behaviour in aqueous environments

High-entropy alloys (HEAs) are a newly developed family of multi-component alloys. The potentiodynamic polarization and electrochemical impedance spectroscopy of the Al_xCrFe_1.5MnNi_0.5 alloys, obtained in H₂SO₄ and NaCl solutions, clearly revealed that the corrosion resistance increases as the concentration of aluminium decreases. The Al_xCrFe_1.5MnNi_0.5 alloys exhibited a wide passive region, which extended >1000 mV in acidic environments. The Nyquist plots of the Al-containing alloys had two capacitive loops, which represented the electrical double layer and the adsorptive layer. SEM micrographs revealed that the general and pitting corrosion susceptibility of the HEAs increased as the amount of aluminium in the alloy increased.     

Electrochemical passive properties of AlxCoCrFeNi (x = 0, 0.25, 0.50, 1.00) alloys in sulfuric acids

This study investigates the electrochemical passive properties of Al_xCoCrFeNi alloys in H₂SO₄ by potentiodynamic polarization, EIS, and weight loss tests from 20 to 65 °C. Experimental results indicate that Al harms the corrosion resistance in H₂SO₄ at temperatures exceeding 27 °C owing to the porous and inferior nature of the protection oxide film of Al in these alloys. Closely examining the Arrhenius plots of corrosion current density reveals that both pre-exponential factor A and activation energy E_a increase with Al content. However, A affects corrosion current density more significantly than E_a at higher temperatures and, conversely, at lower temperatures.     

Electrochemical corrosion behavior of Mg-5Al-0.4Mn-xNd in NaCl solution

The electrochemical corrosion behavior of Mg-5Al-0.4Mn-xNd (x = 0, 1, 2 and 4 wt.%) alloys in 3.5% NaCl solution was investigated. The corrosion behavior of the alloys was assessed by open circuit potential measure, potentiodynamic polarization, and electrochemical impedance spectroscopy. The electrochemical results show the intermetallic precipitates with Nd behave as less noble cathodes in micro-galvanic corrosion and suppress the cathodic process. During corrosion, Al₂O₃ and Nd₂O₃, in proper ratio, is incorporated into the corrosion film, and enhances the corrosion resistance.     

Corrosion behaviour of silicon-carbide-particle reinforced AZ92 magnesium alloy

The corrosion behaviour of silicon-carbide-particle (SiCp) reinforced AZ92 magnesium alloy manufactured by a powder metallurgy process was evaluated in 3.5 wt.% NaCl solution, neutral salt fog (ASTM B 117) and high relative humidity (98% RH, 50 °C) environments. The findings revealed severe corrosion of AZ92/SiC/0-10p materials in salt fog environment with formation of corrosion products consisting of Mg(OH)₂ and (Mg,Al)_x(OH)_y. The addition of SiCp increased the corrosion rate and promoted cracking and spalling of the corrosion layer for increasing exposure times. Composite materials revealed higher corrosion resistance in high humidity atmosphere with almost no influence of SiCp on the corrosion behaviour.     

Molten glass corrosion resistance of MoxRuySiz compounds at 1350 °C in an alkali borosilicate glass

Corrosion of Mo-silicides and Mo_xRu_ySi_z compounds in molten glass is studied by electrochemical techniques at 1350 °C, metallographic observations (SEM) and chemical analysis (EPMA). The open circuit potential measurements (free-potential) enabled the determination of the reactions responsible for the degradation of the materials.The degradation of Mo-silicide occurs through selective oxidation of Si. Mo_xRu_ySi_z compounds were subjected to reactions leading to the successive oxidation of silicon and molybdenum. The progressive depletion of Si and Mo resulted in the more or less quick formation of a thick, porous and low adherent Ru-layer. Therefore, Ru-additions had no positive effect on the molten glass corrosion resistance of MoSi₂-based materials and should even accelerate the degradation kinetics of the later through galvanic coupling.     

Analysis of the electrochemical reaction behavior of alloy AZ91 by EIS technique in H3PO4/KOH buffered K2SO4 solutions

The EIS technique was used to analyze the electrochemical reaction behavior of Alloy AZ91 in H₃PO₄/KOH buffered K₂SO₄ solution at pH 7. The corrosion resistance of Alloy AZ91 was directly related with the stability of Al₂O₃ · xH₂O rich part of the composite oxide/hydroxide layer on the alloy surface. The break down of the oxide layer was estimated to occur mainly on the matrix solid solution phase in Alloy AZ91. The mf capacitive loop arose from the relaxation of mass transport in the solid oxide phase in the presence of Al₂O₃ · xH₂O rich part and from Mg⁺ ion concentration within the broken area in the absence of Al₂O₃ · xH₂O rich part in the composite oxide structure on the alloy surface. The lf inductive loop had tendency of disappear when the dissolution rate of the alloy decreased as a result of the formation of the protective oxide layer.     

Electrochemical response of AlNiLa amorphous and devitrified alloys

The electrochemical response of Al_94−xNi₆La_x alloys (x = 4, 5, 6, 7) after different stages of devitrification was studied in 0.05 M Na₂SO₄ as well as in different concentrations [0.001 M, 0.01 M and 0.1 M] NaCl solutions. Complementary crystallization studies were carried out to elucidate the composition dependent phase evolution in these alloys. It was observed that the primary crystallization did not cause any deterioration in the corrosion resistance of the alloys as compared to the amorphous alloys. In the case of Al₈₇Ni₆La₇, there was actually an improvement in the passivating ability in benign media. The various primary crystalline phases in the different alloys investigated did not cause different electrochemical responses. However, the onset of secondary crystallization caused a reduction in the corrosion resistance in the NaCl media through a loss in passivating ability of all the alloys. This is due to increased galvanic activity as well as the loss of the amorphous phase.     

Investigating the correlation between nano-impact fracture resistance and hardness/modulus ratio from nanoindentation at 25-500 °C and the fracture resistance and lifetime of cutting tools with Ti1−xAlxN (x = 0.5 and 0.67) PVD coatings in milling operations

A novel laboratory technique, nano-impact testing, has been used to test Ti_1−xAl_xN (x = 0.5 and 0.67) PVD coated WC-Co inserts at 25-500 °C. Cutting tool life was studied under conditions of face milling of the structural AISI 1040 steel; the end milling of hardened 4340 steel (HRC 40) and TiAl6V4 alloy. A correlation was found between the results of the rapid nano-impact test and milling tests. When x = 0.67 improved resistance to fracture was found during milling operations and also in the nano-impact test of this coating compared to when x = 0.50. The coating protects the cutting tool surface against the chipping that is typical for cutting operations with intensive adhesive interaction with workpiece materials such as machining of Ti-based alloys. The results give encouragement that the elevated temperature nano-impact test can be used to predict the wear and fracture resistance of hard coatings during milling operations. At 500 °C nanoindentation shows there is a lower H/E_r ratio for the PVD coatings compared to room temperature, consistent with reduced fracture observed at this temperature in the nano-impact test.     

Hot corrosion behaviour of low Al NiCoCrAlY cladded coatings reinforced by nano-particles on a Ni-base super alloy

Three NiCoCrAlY coatings with Al content lower than 5 wt.% reinforced by different kinds of nano-particles with the same addition and one without nano-particles were prepared on a Ni-base super alloy using laser cladding technique. Hot corrosion of the NiCoCrAlY coatings in Na₂SO₄/K₂SO₄ (75:25, wt./wt.) mixture was performed at 1050 °C in static air. Results indicate that the hot corrosion resistance of the coatings with nano-particles is better than that of the one without nano-particles, among which the one with nano-CeO₂ presented the best hot corrosion resistance. Effects of nano-particles on the hot corrosion behaviour were also discussed.     

High temperature scaling of Ni-xSi-10 at.% Al alloys in 1 atm of pure O2

The oxidation of Ni-xSi-10Al alloys (with x = 0, 2, 4 and 6 at.%), has been studied at 900 and 1000 °C in 1 atm of pure O₂ to examine the effect of different silicon additions on the behavior of ternary Ni-Si-10Al alloys. The kinetic curves of Ni-10Al are approximately parabolic at both 900 and 1000 °C. Conversely, the kinetics of the ternary alloys at both temperatures correspond generally to a rate decrease faster than predicted by the parabolic rate law, except for the oxidation of Ni-6Si-10Al at 1000 °C, which exhibits a single nearly-parabolic stage. Oxidation of the binary alloy formed at both temperatures an internal oxidation zone beneath a layer of NiO. Oxidation of Ni-2Si-10Al at both temperatures and of the other two alloys at 900 °C formed initially a zone of internal oxidation of Al + Si. However, a layer of alumina forming at the front of internal oxidation after some time blocked the internal oxidation and produced a gradual conversion of the metal matrix of this region into NiO, with a simultaneous decrease of the oxidation rate. Conversely, the oxidation of Ni-4Si-10Al and Ni-6Si-10Al at 1000 °C did not produce an internal oxidation, but formed an alumina layer directly on the alloy surface after an initial stage when also Ni was oxidized. Therefore, silicon exerts the third-element effect by reducing the critical Al content needed for the transition from its internal to its external oxidation with respect to the corresponding Ni-Al alloy. This result is interpreted by means of an extension to ternary alloys of Wagner’s criterion for the same transition in binary alloys based on the attainment of a critical volume fraction of internal oxide.     

Corrosion protection of magnesium alloy AZ31 sheets by spin coating process with poly(ether imide) [PEI]

In the present study, the potential of poly(ether imide) as corrosion protective coating for magnesium alloys was evaluated using the spin coating technique. The influence of different parameters on the coating properties was evaluated and the corrosion behaviour of the coatings was investigated using electrochemical impedance spectroscopy. The best corrosion protection was obtained preparing the coatings under N₂ atmosphere, using 15 wt.% solution in N′N′-dimethylacetamide (DMAc) which resulted in a coating of approximately 2 μm thickness, with an initial impedance of 10⁹ Ω cm² and of 10⁵ Ω cm² after 240 h of exposure to a 3.5% NaCl solution.     

Corrosion behaviour of die-cast AZ91D magnesium alloy in aqueous sulphate solutions

The corrosion behaviour of die-cast AZ91D magnesium alloys in sulphate solutions was investigated by SEM, FTIR and polarization measurements. For immersion times less than 48 h, no pitting corrosion occurred and only generalized corrosion was apparent. According to the polarization curves, the corrosion rate order of the die-cast AZ91D Mg alloy in three aqueous solutions was: NaCl > MgSO₄ > Na₂SO₄. The main corrosion products were Mg(OH)₂ and MgAl₂(SO₄)₄·22H₂O in the sulphate solutions and the product film was compact. Precipitation of MgAl₂(SO₄)₄·22H₂O required a threshold immersion time.     

Structural, electronic, optical and thermodynamic properties of SrxCa1−xO, BaxSr1−xO and BaxCa1−xO alloys

The structural, electronic, optical and thermodynamic properties of Sr_xCa_1−xO, Ba_xSr_1−xO and Ba_xCa_1−xO ternary alloys in NaCl phase were studied using pseudo-potential plane-wave method within the density functional theory. We modeled the alloys at some selected compositions with ordered structures described in terms of periodically repeated supercells. The dependence of the lattice parameters, band gaps, dielectric constants, refractive indices, Debye temperatures, mixing entropies and heat capacities on the composition x were analyzed for x = 0, 0.25, 0.50, 0.75 and 1. The lattice constant for Sr_xCa_1−xO and Ba_xSr_1−xO exhibits a marginal deviation from the Vegard's law, while the Ba_xCa_1−xO lattice constant exhibits an appreciable upward bowing. A strong deviation of the bulk modulus from linear concentration dependence was observed for the three alloys. The microscopic origins of the gap bowing were detailed and explained. The composition dependence of the dielectric constant and refractive index was studied using different models. The thermodynamic stability of these alloys was investigated by calculating the phase diagram. The thermal effect on some macroscopic properties was investigated using the quasi-harmonic Debye model. There is a good agreement between our results and the available experimental data for the binary compounds which may be a support for the results of the ternary alloys reported here for the first time.