Development of new catalysts for deep hydrodesulfurization of gas oil

TiO₂–Al₂O₃ composite supports have been prepared by chemical vapor deposition (CVD) over γ-Al₂O₃ substrate, using TiCl₄ as the precursor. High dispersion of TiO₂ overlayer on the surface of Al₂O₃ has been obtained, and no cluster formation has been detected. The catalytic behavior of Mo supported on Al₂O₃, TiO₂ and TiO₂–Al₂O₃ composite has been investigated for the hydrodesulfurization (HDS) of dibenzothiophene (DBT) and methyl-substituted DBT derivatives. The conversion over the Mo catalysts supported on TiO₂–Al₂O₃ composite, in particular for the HDS of 4,6-dimethyldibenzothiophene (4,6-DMDBT) is much higher than that of conversion obtained over Mo catalyst supported on Al₂O₃. The ratio of the corresponding cyclohexylbenzenes/biphenyls is increased over Mo catalyst supported on TiO₂–Al₂O₃ composite support. This means that the reaction rate of prehydrogenation of an aromatic ring rather than the rate of hydrogenolysis of C–S bond cleavage is accelerated for the HDS of DBT derivatives. The Mo/TiO₂–Al₂O₃ catalyst leads to higher catalytic performance for deep HDS of gas oil.     

Hydrodesulfurization of dibenzothiophenes over molybdenum catalyst supported on TiO2–Al2O3

Composite types of TiO₂–Al₂O₃ supports, which are γ-aluminas coated by titania, have been prepared by chemical vapor deposition (CVD), using TiCl₄ as a precursor. Then supported molybdenum catalysts have been prepared by an impregnation method. As supports, we employed γ-alumina, anatase types of titania, and composite types of TiO₂–Al₂O₃ with different loadings of TiO₂. We studied the conversion of Mo from oxidic to sulfidic state through sulfurization by X-ray photoelectron spectroscopy (XPS). The obtained spectra unambiguously revealed the higher reducibility from oxidic to sulfidic molybdenum species on the TiO₂ and TiO₂–Al₂O₃ supports compared to that on the Al₂O₃ support. Higher TiO₂ loadings of the TiO₂–Al₂O₃ composite support led to higher reducibility for molybdenum species. Furthermore, the catalytic behavior of supported molybdenum catalysts has been investigated for hydrodesulfurization (HDS) of dibenzothiophene (DBT) and methyl-substituted DBT derivatives. The conversion over the TiO₂–Al₂O₃ supported Mo catalysts, in particular for the 4,6-dimethyl-DBT, is much higher than that obtained over Al₂O₃ supported Mo catalyst. The ratio of the corresponding cyclohexylbenzene (CHB)/biphenyl (BP) derivatives is increased over the Mo/TiO₂–Al₂O₃. This indicates that the prehydrogenation of an aromatic ring plays an important role in the HDS of DBT derivatives over TiO₂–Al₂O₃ supported catalysts.     

Catalytic activities of Co(Ni)Mo/TiO2–Al2O3 catalysts in gasoil and thiophene HDS and pyridine HDN: effect of the TiO2–Al2O3 composition

The effect of the TiO₂–Al₂O₃ mixed oxide support composition on the hydrodesulfurization (HDS) of gasoil and the simultaneous HDS and hydrodenitrogenation (HDN) of gasoil+pyridine was studied over two series of CoMo and NiMo catalysts. The intrinsic activities for gasoil HDS and pyridine HDN were significantly increased by increasing the amount of TiO₂ into the support, and particularly over rich- and pure-TiO₂-based catalysts. It is suggested that the increase in activity be due to an improvement in reducing and sulfiding of molybdena over TiO₂. The inhibiting effect of pyridine on gasoil HDS was found to be similar for all the catalysts, i.e., was independent of the support composition. The ranking of the catalysts for the gasoil HDS test differed from that obtained for the thiophene test at different hydrogen pressures. In the case of gasoil HDS, the activity increases with TiO₂ content and large differences are observed between the catalysts supported on pure Al₂O₃ and pure TiO₂. In contrast, in the case of the thiophene test, the pure Al₂O₃-based catalyst appeared relatively more active than the catalysts supported on mixed oxides. Also, in the thiophene test the difference in intrinsic activity between the pure Al₂O₃-based catalyst appeared relatively more active than the catalysts supported on mixed oxides. Also in the thiophene test, the difference in intrinsic activity between the pure Al₂O₃- and pure TiO₂-based catalysts is relatively small and dependent on the H₂ pressure used. Such differences in activity trend among the gasoil and the thiophene tests are due to a different sensitivity of the catalysts (by different support or promoter) to the experimental conditions used. The results of the effect of the H₂ partial pressure on the thiophene HDS, and on the effect of H₂S concentration on gasoil HDS demonstrate the importance of these parameters, in addition to the nature of the reactant, to perform an adequate catalyst ranking.     

Improvement of catalytic activity and sulfur-resistance of Ag/TiO2–Al2O3 for NO reduction with propene under lean burn conditions

Ag-based catalysts supported on various metal oxides, Al₂O₃, TiO₂, and TiO₂–Al₂O₃, were prepared by the sol–gel method. The effect of SO₂ on catalytic activity was investigated for NO reduction with propene under lean burn condition. The results showed the catalytic activities were greatly enhanced on Ag/TiO₂–Al₂O₃ in comparison to Ag/Al₂O₃ and Ag/TiO₂, especially in the low temperature region. Application of different characterization techniques revealed that the activity enhancement was correlated with the properties of the support material. Silver was highly dispersed over the amorphous system of TiO₂–Al₂O₃. NO₃⁻ rather than NO₂⁻ or NOx reacted with the carboxylate species to form CN or NCO. NO₂ was the predominant desorption species in the temperature programmed desorption (TPD) of NO on Ag/TiO₂–Al₂O₃. More amount of formate (HCOO⁻) and CN were generated on the Ag/TiO₂–Al₂O₃ catalyst than the Ag/Al₂O₃ catalyst, due to an increased number of Lewis acid sites. Sulfate species, resulted from SO₂ oxidation, played dual roles on catalytic activity. On aged samples, the slow decomposition of accumulated sulfate species on catalyst surface led to poor NO conversion due to the blockage of these species on active sites. On the other hand, catalytic activity was greatly enhanced in the low temperature region because of the enhanced intensity of Lewis acid site caused by the adsorbed sulfate species. The rate of sulfate accumulation on the Ag/TiO₂–Al₂O₃ system was relatively slow. As a consequence, the system showed superior capability for selective adsorption of NO and SO₂ toleration to the Ag/Al₂O₃ catalyst.     

Tailoring of alumina surfaces as supports for NiMo sulfide catalysts in the ultra deep hydrodesulfurization of gas oil: case study of TiO2-coated alumina prepared by chemical vapor deposition technique

The present paper gives a detailed review of the different studies under investigation in our laboratory concerning the use of TiO₂ and TiO₂–Al₂O₃ composites prepared by chemical vapor deposition (CVD) as support for sulfide catalysts in the HDS of dibenzothiophene (DBT) derivatives. The supports investigated here are: TiO₂ (from Degussa, 50 m²/g), Al₂O₃ (Nikki, 186 m²/g) and TiO₂–Al₂O₃ supports prepared by CVD of TiCl₄ on alumina. Using several characterization techniques, we have demonstrated that the support composite presents a high dispersion of TiO₂ over γ-Al₂O₃ without forming precipitates up to ca. 11 wt.% loading. Moreover, the textural properties of the support composite are comparable to those of alumina. XPS investigations of Mo and NiMo catalysts supported on the different carriers show that Mo-oxide species exhibit a higher degree of sulfidation on the surface of TiO₂ and TiO₂–Al₂O₃ than on alumina. The HDS tests of 4,6-DMDBT under mild operating conditions (573 K, 3 MPa) show that sulfide catalysts supported on the composite support (ca. 11 wt.%) are more active than those supported on to TiO₂ or Al₂O₃. This higher HDS catalytic activity is attributed to the promotion of the hydrodesulfurization pathway, whereby the pre-hydrogenation of one of the aromatic rings adjacent to the thiophenic one may reduce the steric hindrance caused by the two methyl groups adjacent to the sulfur atom during the C–S bond cleavage.     

Catalytic performance of a novel ceramic-supported vanadium oxide catalyst for NO reduction with NH3

A novel TiO₂/Al₂O₃/cordierite honeycomb-supported V₂O₅–MoO₃–WO₃ monolithic catalyst was studied for the selective reduction of NO with NH₃. The effects of reaction temperature, space velocity, NH₃/NO ratio and oxygen content on SCR activity were evaluated. Two other V₂O₅–MoO₃–WO₃ monolithic catalysts supported on Al₂O₃/cordierite honeycomb or TiO₂/cordierite honeycomb support, two types of pellet catalysts supported on TiO₂/Al₂O₃ or Al₂O₃, as well as three types of pellet catalysts V₂O₅–MoO₃–WO₃–Al₂O₃ and V₂O₅–MoO₃–WO₃–TiO₂ were tested for comparison. The experiment results show that this catalyst has a higher catalytic activity for SCR with comparison to others. The results of characterization show, the preparation method of this catalyst can give rise to a higher BET surface area and pore volume, which is strongly related with the highly active performance of this catalyst. At the same time, the function of the combined carrier of TiO₂/Al₂O₃ cannot be excluded.     

TiO2-coated on Al2O3 support prepared by the CVD method for HDS catalysts

Mo---Co or Mo---Ni catalysts supported on alumina (Al₂O₃) have been widely used for hydrodesulfurization (HDS) of heavy petroleum fractions. In order to enhance the catalytic activities for HDS, a composite type support (TiO₂-Al₂O₃) prepared by the chemical vapor deposition (CVD) method has been studied. We found that Mo catalyst supported on TiO₂-Al₂O₃ showed much higher catalytic activity for HDS of dibenzothiophene derivatives than the catalysts supported on Al₂O₃.     

Maya crude hydrodemetallization and hydrodesulfurization catalysts: An effect of TiO2 incorporation in Al2O3

Hydrotreating of Maya heavy crude oil over high specific surface area CoMo/TiO₂–Al₂O₃ oxide supported catalysts was studied in an integral reactor close to industrial practice. Activity studies were carried out with Maya crude hydrodesulfurization (HDS), hydrodemetallization (HDM), hydrodenitrogenation (HDN), and hydrodeasphaltenization (HDAs) reactions. The effect of support composition, the method of TiO₂ incorporation, and the catalyst deactivation are examined. Supported catalysts are characterized by BET specific surface area (SSA), pore volume (PV), pore size distribution (PSD), and atomic absorption. It has been found that sulfided catalysts showed a wide range of activity variation with TiO₂ incorporation into the alumina, which confirmed that molybdenum sulfided active phases strongly depend on the nature of support. The pore diameter and nature of the active site for HDS, HDM, HDN, and HDAs account for the influence of the large reactant molecules restricted diffusion into the pore, and/or the decrease in the number of active sites due to the MoS₂ phases buried with time-on-stream. The textural properties and hysteresis loop area of supported and spent catalysts indicated that catalysts were deactivated at the pore mouth due to the metal and carbon depositions. The atomic absorption results agreed well regarding the textural properties of spent catalysts. Thus, incorporation of TiO₂ with γ-Al₂O₃ alters the nature of active metal interaction with support, which may facilitate the dispersion of active phases on the support surface. Therefore, the TiO₂ counterpart plays a promoting role to HDS activity due to the favorable morphology of MoS₂ phases and metal support interaction.     

Preparation and characterization of nano-sized CoMo/Al2O3 catalyst for hydrodesulfurization

CoMo on Al₂O₃ catalyst prepared by spray pyrolysis method was found in the form of spheres of 0.5–1.2 μm, which consisted of tiny primary particles of ca. 10–20 nm diameter. The materials shows comparable activity to those of commercial catalysts in HDS of straight run gas oil, in particular, refractory 4,6-dimethyldibenzothiophene (4,6-DMDBT). Weaker interactions between CoMo and Al₂O₃ are suggested by temperature-programmed reduction (TPR), Raman spectroscopy, to give more active species than those over the impregnated catalysts. This accounts for its comparable activity in spite of its smaller surface area.     

Hydrodesulfurization of thiophene, dibenzothiophene and gas oil on various Co---Mo/TiO2-Al2O3 catalysts

Evaluation of Co---Mo catalysts prepared on various TiO₂-Al₂O₃ supports has been made for thiophene under atmospheric pressure, dibenzothiophene under high pressure and gasoil in a classical pilot plant. Comparison of activities indicates DBT as more representative of a real feedstock and the Co---Mo/TiO₂ (50%)-Al₂O₃ (50%) catalyst appears more active than the Co---Mo/Al₂O₃ sample toward HDS, HDN and hydrodearomatization.     

Support Effects on Thiophene Hydrodesulfurization over Co-Mo-Ni/Al2O3 and Co-Mo-Ni/TiO2-Al2O3 Catalysts

A carbon-based sulfonated catalyst was prepared by direct sulfonation and carbonization （in moderate conditions：200 ＆#176;C, 12 h） of red liquor solids, a by-product of paper-making process. The prepared sulfonated cata-lyst （SC） had aromatic structure, composed of carbon enriched inner core, and oxygen-containing （SO3H, COOH, OH） groups enriched surface. The SO3H, COOH, OH groups amounted to 0.74 mmol·g^-1, 0.78 mmol·g^-1, 2.18 mmol·g^-1, respectively. The fresh SC showed much higher catalytic activity than that of the traditional solid acid catalysts （strong-acid 732 cation exchange resin, hydrogen type zeolite socony mobile-five （HZSM-5）, sulfated zir-conia） in esterification of oleic acid. SC was deactivated during the reactions, through the mechanisms of leaching of sulfonated species and formation of sulfonate esters. Two regeneration methods were developed, and the catalytic activity can be mostly regenerated by regeneration Method 1 and be fully regenerated by regeneration Method 2, respectively.     

Niobium sulfide as a dopant for Mo/TiO2 catalysts

Mo/TiO₂ catalysts were modified with Nb by two different methods, sol–gel and surface deposition, in order to study the effect of Nb incorporation on the thiophene HDS activity. The results show that the formation of Nb–Ti mixed oxides leads to catalysts with poor HDS activity while the deposition of Nb oxide species on the surface of TiO₂ leads to catalysts with activities larger than those of Mo/Al₂O₃ and Mo/TiO₂. This increase in activity was attributed to the formation of a larger population of Mo sulfur anionic vacancies when Nb was surface deposited on the TiO₂.     

Catalytic hydrotreatment on alumina–titania supported NiMo sulphides

MoNi/Al₂O₃ catalysts have been widely used for hydrodesulphurisation of oil fractions. In order to enhance the catalytic activities for HDS and HDN, catalysts supported on titania-modified alumina carriers have been studied. The MoNi/Al₂O₃–TiO₂catalysts were characterised by benzene sorption, ammonia sorption, temperature programmed reduction, X-ray diffraction and scanning electron microscopy. The supports effect was examined by comparing thiophene conversion and sulphur or nitrogen contents in diesel oil fraction.     

Role of CeO2 in Ni/CeO2–Al2O3 catalysts for carbon dioxide reforming of methane

Ni catalysts supported on γ-Al₂O₃, CeO₂ and CeO₂–Al₂O₃ systems were tested for catalytic CO₂ reforming of methane into synthesis gas. Ni/CeO₂–Al₂O₃ catalysts showed much better catalytic performance than either CeO₂- or γ-Al₂O₃-supported Ni catalysts. CeO₂ as a support for Ni catalysts produced a strong metal–support interaction (SMSI), which reduced the catalytic activity and carbon deposition. However, CeO₂ had positive effect on catalytic activity, stability, and carbon suppression when used as a promoter in Ni/γ-Al₂O₃ catalysts for this reaction. A weight loading of 1–5 wt% CeO₂ was found to be the optimum. Ni catalysts with CeO₂ promoters reduced the chemical interaction between nickel and support, resulting in an increase in reducibility and stronger dispersion of nickel. The stability and less coking on CeO₂-promoted catalysts are attributed to the oxidative properties of CeO₂.     

Enhanced activity of metal oxide-doped Ga2O3–Al2O3 for NO reduction by propene

Effect of additives, In₂O₃, SnO₂, CoO, CuO and Ag, on the catalytic performance of Ga₂O₃–Al₂O₃ prepared by sol–gel method for the selective reduction of NO with propene in the presence of oxygen was studied. As for the reaction in the absence of H₂O, CoO, CuO and Ag showed good additive effect. When H₂O was added to the reaction gas, the activity of CoO-, CuO- and Ag-doped Ga₂O₃–Al₂O₃ was depressed considerably, while an intensifying effect of H₂O was observed for In₂O₃- and SnO₂-doped Ga₂O₃–Al₂O₃. Of several metal oxide additives, In₂O₃-doped Ga₂O₃–Al₂O₃ showed the highest activity for NO reduction by propene in the presence of H₂O. Kinetic studies on NO reduction over In₂O₃–Ga₂O₃–Al₂O₃ revealed that the rate-determining step in the absence of H₂O is the reaction of NO₂ formed on Ga₂O₃–Al₂O₃ with C₃H₆-derived species, whereas that in the presence of H₂O is the formation of C₃H₆-derived species. We presumed the reason for the promotional effect of H₂O as follows: the rate for the formation of C₃H₆-derived species in the presence of H₂O is sufficiently fast compared with that for the reaction of NO₂ with C₃H₆-derived species in the absence of H₂O. Although the retarding effect of SO₂ on the activity was observed for all of the catalysts, SnO₂–Ga₂O₃–Al₂O₃ showed still relatively high activity in the lower temperature region.     

Non-steady activity during methane combustion over Pd/Al2O3 and the influences of Pt and CeO2 additives

Methane combustion over Pd/Al₂O₃ catalysts with and without added Pt and CeO₂ in both oxygen-rich and methane-rich mixtures at temperatures in the range 250–520°C has been investigated using a temperature-programmed reaction procedure with on-line gas analysis (FTIR). During the temperature loop under oxygen-rich conditions, there was an appreciable hysteresis in the activity of unmodified Pd/Al₂O₃, which was greatly enhanced over Pd–Pt/Al₂O₃. Over both catalysts the hysteresis was reversed under slightly methane-rich atmospheres, and as temperature was reduced, a sudden collapse or fluctuations in activity were shown respectively over Pd–Pt/Al₂O₃ and Pd/Al₂O₃. Such non-steady behaviour was almost eliminated over Pd/Al₂O₃–CeO₂. Under a very narrow range of conditions and over a Pd/Al₂O₃ packed bed, oscillation of methane combustion was observed.     

HDS and HDN activity of molybdenum and nickel–molybdenum catalysts supported on alumina–titania carriers

Alumina–titania supports containing 5–50 wt.% of TiO₂ were prepared by coprecipitation method using inorganic precursors (sodium aluminate and titanium chloride). DTA-TGA, XRD, SEM, TPD_NH3, and IR spectroscopy were used to characterise these materials. The study shows that the promoting effect of nickel on the HDS activity of molybdenum catalysts supported on Al₂O₃TiO₂ is significantly lower than that for molybdenum catalyst supported on Al₂O₃, and depends on the TiO₂ content. The SEM results show that in the case of rich Al support (20 wt.% of TiO₂) molybdenum was aggregated on the external surface of the catalyst, whereas it was uniformly dispersed on the external surface of alumina. Results also show that molybdenum is preferably supported on aluminum oxide. Application of Al₂O₃TiO₂ oxides enhances the HDN activity of nickel–molybdenum catalysts. The highest HDN efficiency was obtained for the NiMo/Al₂O₃TiO₂ catalyst containing 50 wt.% of TiO₂. HDN activity was found to depend on protonic acidity and anatase content.     

Ni/Al_2O_3催化剂的CO_2-TPD表征

Ni/Al_2O_3催化剂是甲烷二氧化碳重整反应制取合成气研究最多、最具应用潜力的一种催化剂。通过对催化剂进行CO_2-TPD研究,考察还原态Ni/Al_2O_3催化剂的CO_2脱附特性。结果表明,浸渍法制备的Ni/Al_2O_3催化剂CO_2脱附曲线呈现双峰,分别在(60~65)℃和(350~380)℃出现高低温两个活性位;高温CO_2吸附量为3.0 cm~3·g~(-1),低温CO_2吸附量为24.0 cm~3·g~(-1)。催化剂的CO_2吸附量与其Ni含量无关。考察选用不同载体的CO_2脱附行为,发现以Al_2O_3为载体的催化剂CO_2吸附量是MgO和SiO_2为载体催化剂的2~4倍,以TiO_2为载体的催化剂几乎不吸附CO_2。     

Oxides of copper, ceria promoted copper, manganese and copper manganese on Al2O3 for the combustion of CO, ethyl acetate and ethanol

Combustion of CO, ethyl acetate and ethanol was studied over CuO_x/Al₂O₃, CuO_x–CeO₂/Al₂O₃, CuMn₂O₄/Al₂O₃ and Mn₂O₃/Al₂O₃ catalysts. It was found that modification of the alumina with ceria before subsequent copper oxide deposition increases the activity for combustion of CO substantially, but the effect of ceria was small on the combustion of ethyl acetate and ethanol. The activity increases with the CuO_x loading until crystalline CuO particles are formed, which contribute little to the total active surface. The CuO_x–CeO₂/Al₂O₃ catalyst is more active than the CuMn₂O₄/Al₂O₃ catalyst for the oxidation of CO but the CuMn₂O₄/Al₂O₃ catalyst is more active for the combustion of ethyl acetate and ethanol.

Thermal ageing and water vapour in the feed caused a modest decrease in activity and did not affect the CuO_x–CeO₂/Al₂O₃ and CuMn₂O₄/Al₂O₃ catalysts differently. In addition, no difference in intermediates formed over the two catalysts was observed.

Characterisation with XRD, FT-Raman and TPR indicates that the copper oxide is present as a copper aluminate surface phase on alumina at low loading. At high loading, bulk CuO crystallites are present as well. Modification of the alumina with ceria before the copper oxide deposition gives well dispersed copper oxide species and bulk CuO crystallites associated to the ceria, in addition to the two copper oxide species on the bare alumina. The distribution of copper species depends on the ceria and copper oxide loading. The alumina supported copper manganese oxide and manganese oxide catalysts consist mainly of crystalline CuMn₂O₄ and Mn₂O₃, respectively, on Al₂O₃.     

Performance of spent sulfide catalysts in hydrodesulfurization of straight run and nitrogen-removed gas oils

After the test run of several months two kinds of commercial catalysts (NiMo/Al₂O₃ and CoMo/Al₂O₃) were examined in hydrodesulfurization (HDS) of straight run (SRGO) and nitrogen-removed gas oils, at 340 °C under 50 kg/cm² H₂. Hydrogen renewal between stages was attempted to show additional inhibition effects of the by-products such as H₂S and NH₃. Spent NiMo/Al₂O₃ and CoMo/Al₂O₃ catalysts showed contrasting activities in HDS and susceptibility to nitrogen species, according to their catalytic natures, compared to those of their virgin ones. HDS over spent NiMo/Al₂O₃ was significantly improved by removal of nitrogen species, while that over spent CoMo/Al₂O₃ was much improved by H₂ refreshment. The activity for refractory sulfur species such as 4,6-dimethyldibenzothiophene was reduced more severely than that for the reactive sulfur species such as benzothiophenes over spent catalysts. The effects of both two-stage hydrodesulfurization and nitrogen-removal were markedly reduced over the spent NiMo when compared with those over virgin NiMo one. The acidity of the catalysts was correlated with the inhibition susceptibility by nitrogen species as well as H₂S and NH₃. Spent catalysts apparently lost their activity due to the carbon deposition, which covered the active sites more preferentially. The spent NiMo catalyst carried more deposited carbon with larger C/H ratio and nitrogen content. Higher acidity was found to be present on the NiMo catalyst, but this was greatly decreased by the carbon deposition. Additionally, the reactivity of nitrogen species in HDS was briefly discussed in relation to the acidity of the catalyst and its deactivation by carbon deposition.