Poly(ε‐caprolactone)‐graft‐poly(N‐isopropylacrylamide) amphiphilic copolymers prepared by a combination of ring‐opening polymerization and atom transfer radical polymerization: Synthesis,self‐assembly,and thermoresponsive property

Thermoresponsive graft copolymers of ε‐caprolactone and N‐isopropylacrylamide were synthesized by a combination of ring‐opening polymerization and the sequential atom transfer radical polymerization (ATRP). The copolymer composition, chemical structure, and the self‐assembled structure were characterized. The graft length and density of the copolymers were well controlled by varying the feed ratio of monomer to initiator and the fraction of chlorides along PCL backbone, which is acting as the macroinitiator for ATRP. In aqueous solution, PCL‐g‐PNIPAAm can assemble into the spherical micelles which comprise of the biodegradable hydrophobic PCL core and thermoresponsive hydrophilic PNIPAAm corona. The critical micelle concentrations of PCL‐g‐PNIPAAm were determined under the range of 6.4–23.4 mg/L, which increases with the PNIPAAm content increasing. The mean hydrodynamic diameters of PCL‐g‐PNIPAAm micelles depend strongly on the graft length and density of the PNIPAAm segment, allowing to tune the particle size within a wide range. Additionally, the PCL‐g‐PNIPAAm micelles exhibit thermosensitive properties and aggregate when the temperature is above the lower critical solution temperature. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41115.     

Shape memory properties of olefin block copolymer (OBC)/poly(ɛ‐caprolactone) (PCL) blends

Conventionally, the chemically crosslinked shape memory polymer (SMP) blends are hard to recycle due to their network structure. Herein, the environmental SMP blends of olefin block copolymer (OBC), a unique thermoplastic elastomer, and poly(?‐caprolactone) (PCL) were physically crosslinked. Dicumyl peroxide was used as the compatibilizer to improve their miscibility, as evidenced by the reduced dispersed domain size of PCL in the OBC matrix and the increased complex viscosity. The peroxide modified OBC/PCL blend conferred enhanced tensile properties, increased dynamic storage modulus, increased crystallization temperature, and higher recovery stress. The shape memory behaviors of OBC/PCL blends predeformed under two different predeformation temperatures (30 and 65 °C) were investigated. The recovery stress showed respective maximum peak values corresponding to their predeformation temperatures. In addition, the modified blends gave the better shape memory performance at 65 °C. Besides the peroxide modification approach, a precycle training process via prestretching the samples and reducing the mechanical hysteresis was implemented to improve shape memory performance further. This is the first work on the OBC‐based SMP blends to enhance shape memory performance by combining the chemical modification using added peroxide compatibilizer and the process modification using a precycle training process. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 45475.     

Biodegradable magnetic‐sensitive shape memory poly(ɛ‐caprolactone)/Fe3O4 nanocomposites

A novel biodegradable magnetic‐sensitive shape memory poly(?‐caprolactone) nanocomposites, which were crosslinked with functionalized Fe₃O₄ magnetic nanoparticles (MNPs), were synthesized via in situ polymerization method. Fe₃O₄ MNPs pretreated with γ‐(methacryloyloxy) propyl trimethoxy silane (KH570) were used as crosslinking agents. Because of the crosslinking of functionalized Fe₃O₄ MNPs with poly(?‐caprolactone) prepolymer, the properties of the nanocomposites with different content of functionalized Fe₃O₄ MNPs, especially the mechanical properties, were significantly improved. The nanocomposites also showed excellent shape memory properties in both 60 °C hot water and alternating magnetic field (f = 60, 90 kHz, H = 38.7, 59.8 kA m^?1). In hot water bath, all the samples had shape recovery rate (R_r) higher than 98% and shape fixed rate (R_f) nearly 100%. In alternating magnetic field, the R_r of composites was over 85% with the highest at 95.3%. In addition, the nanocomposites also have good biodegradability. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45652.     

Properties and degradation behavior of surface functionalized MWCNT/poly(L‐lactide‐co‐ε‐caprolactone) biodegradable nanocomposites

In this research, poly(L ‐lactide‐co‐ε‐caprolactone) (PLACL) reinforced with well‐dispersed multiwalled carbon nanotubes (MWCNTs) nanocomposites were prepared by oxidization and functionalization of the MWCNT surfaces using oligomeric L ‐lactide (LA) and ε‐caprolactone (CL). It is found that the surface functionalization can effectively improve the dispersion and adhesion of MWCNTs in PLACL. The surface functionalization will have a significant effect on the physical, thermomechanical, and degradation properties of MWCNT/PLACL composites. The tensile modulus, yield stress, tensile strength, and elongation at break of composite increased 49%, 60%, 70%, and 94%, respectively, when the concentration of functionalized MWCNTs in composite is 2 wt %. The in vitro degradation rate of nanocomposites in phosphate buffer solution increased about 100%. The glass transition temperature (T_g) of composites was decreased when the concentration of functionalized MWCNTs is 0.5 wt %. With further increasing the concentration of functionalized MWCNTs, the T_g was increased. The degradation kinetics of nanocomposites can be engineered and functionalized by varying the contents of pristine or functionalized MWCNTs. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Shape‐memory behaviors of electrospun chitosan/poly(ethylene oxide) composite nanofibrous membranes

With aim of constructing a class of functional environmentally friendly materials, we electrospun chitosan (CS) blends with various contents of poly(ethylene oxide) (PEO) into a series of composite nanofibrous membranes exhibiting shape‐memory behaviors. In the present composite system, CS and PEO served as hard and soft domains, respectively. The CS, presenting no thermal transition, and the PEO, with apparent melting–crystallization, were demonstrated by differential scanning calorimetry testing. Characterizations also revealed that the morphologies of the CS/PEO membranes were controlled by the mass ratios of CS/PEO. The composite fibrous membranes showed great mechanical performances and thermal stabilities as well. Moreover, CS/PEO possessed excellent shape‐memory behaviors. Such fibrous membranes could complete their shape‐recovery processes within 20 s at the temperature of 20°C above the melting transition temperature (T_m). Both the shape fixity and shape‐recovery ratios were higher than 90%, even after five cycles. The CS/PEO fibrous membranes present significant potential applications in the field of biotechnology and tissue engineering, such as in scaffolds and smart tubes. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42532.     

Synthesis and characterization of poly(L‐lactide‐co‐ϵ‐caprolactone)‐b‐poly(L‐lactide) biodegradable diblock copolyesters: Effect of the block lengths on their thermal properties

Poly(L ‐lactide‐co‐ε‐caprolactone)‐b‐poly(L ‐lactide) [P(LL‐co‐CL)‐b‐PLL] diblock copolyesters were synthesized in a two‐step process with 1‐dodecanol (DDC) and stannous octoate as the initiating system. In the first‐step reaction, a 50:50 mol % amorphous poly(L ‐lactide‐co‐ε‐caprolactone) [P(LL‐co‐CL)] copolyester was synthesized via the bulk copolymerization of L ‐lactide and ε‐caprolactone, which was followed by the polymerization of the PLL crystalline block at the end chain in the second‐step reaction. The yielded copolyesters were characterized with dilute‐solution viscometry, gel permeation chromatography, ¹H‐ and ¹³C‐NMR, and differential scanning calorimetry methods. The molecular weights of the P(LL‐co‐CL) copolyesters from the first‐step reaction were controlled by the DDC concentrations, whereas in the second‐step reaction, the molecular weights of the P(LL‐co‐CL)‐b‐PLL diblock copolyesters depended on the starting P(LL‐co‐CL) copolyester molecular weights and L ‐lactide/prepolymer molar ratios. The starting P(LL‐co‐CL) copolyester molecular weights and PLL block lengths seemed to be the main factors affecting specific thermal properties, including the melting temperature (T_m), heat of melting (ΔH_m), crystallizing temperature (T_c), and heat of crystallizing (ΔH_c), of the final P(LL‐co‐CL)‐b‐PLL diblock copolyester products. T_m, ΔH_m, T_c, and ΔH_c increased when the PLL block lengths increased. However, these thermal properties of the diblock copolyesters also decreased when the P(LL‐co‐CL) block lengths increased. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Part 7. Effects of poly(L‐lactide‐co‐ϵ‐caprolactone) on morphology,structure, crystallization,and physical properties of blends of poly(L‐lactide) and poly(ϵ‐caprolactone)

Blended films of poly(L ‐lactide) [ie poly(L ‐lactic acid)] (PLLA) and poly(?‐caprolactone) (PCL) without or mixed with 10 wt% poly(L ‐lactide‐co‐?‐caprolactone) (PLLA‐CL) were prepared by solution‐casting. The effects of PLLA‐CL on the morphology, phase structure, crystallization, and mechanical properties of films have been investigated using polarization optical microscopy, scanning electron microscopy, differential scanning calorimetry and tensile testing. Addition of PLLA‐CL decreased number densities of spherulites in PLLA and PCL films, and improved the observability of spherulites and the smoothness of cross‐section of the PLLA/PCL blend film. The melting temperatures (T_m) of PLLA and PCL in the films remained unchanged upon addition of PLLA‐CL, while the crystallinities of PLLA and PCL increased at PLLA contents [X_PLLA = weight of PLLA/(weight of PLLA and PCL)] of 0.4–0.7 and at most of the X_PLLA values, respectively. The addition of PLLA‐CL improved the tensile strength and the Young modulus of the films at X_PLLA of 0.5–0.8 and of 0–0.1 and 0.5–0.8, respectively, and the elongation at break of the films at all the X_PLLA values. These findings strongly suggest that PLLA‐CL was miscible with PLLA and PCL, and that the dissolved PLLA‐CL in PLLA‐rich and PCL‐rich phases increased the compatibility between these two phases. © 2003 Society of Chemical Industry     

Shape‐memory effects of radiation crosslinked poly(ϵ‐caprolactone)

Poly(?‐caprolactone) (PCL) with different molecular weight were crosslinked by γ‐radiation. The radiation crosslinking features were analyzed by Soxhlet extraction with toluene and the Charlesby–Pinner equation. The crosslinking degree is relative to molecular weight and radiation dose; the relation between sol fraction and dose follows the Charlesby–Pinner equation. All the samples were crystalline at room temperature, and the radiation crosslinking had a little effect on the crystallinity and the melting behavior of PCL. The shape‐memory results indicated that only those specimens that had a sufficiently high crosslinking degree (gel content is higher than about 10%) were able to show the typical shape‐memory effect, a large recoverable strain, and a high final recovery rate. The response temperature of the recovery effect (about 55°C) was related to the melting point of the samples. The PCL shape‐memory polymer was characterized by its low recovery temperature and large recovery deformation that resulted from the aliphatic polyester chain of PCL. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1589–1595, 2003     

Synthesis and characterization of temperature‐responsive poly(vinyl alcohol)‐based copolymers

A poly(vinyl alcohol) (PVA)/sodium acrylate (AANa) copolymer was synthesized to improve the water solubility of PVA at the ambient temperature. Furthermore, a series of temperature‐responsive acetalyzed poly(vinyl alcohol) (APVA)‐co‐AANa samples of various chain lengths, degrees of acetalysis (DAs), and comonomer contents were prepared via an acid‐catalysis process. Fourier transform infrared and ¹H‐NMR techniques were used to analyze the compositions of the copolymers. The measurement of the turbidity change for APVA‐co‐AANa aqueous solutions at different temperatures revealed that the lower critical solution temperature (LCST) of the copolymers could be tailored through the control of the molecular weight of the starting PVA‐co‐AANa, DA, and comonomer ratios. Lower LCSTs were observed for APVA‐co‐AANa with a longer chain length, a higher DA, and fewer acrylic acid segments. In addition, the LCSTs of the APVA‐co‐AANa aqueous solutions appeared to be salt‐sensitive. The LCSTs decreased as the concentration of NaCl increased. Moreover, atomic force microscopy images of APVA‐co‐AANa around the LCST also proved the temperature sensitivity. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Enhanced crystallization of poly(L‐lactide‐co‐ε‐caprolactone) in the presence of water

Poly(L ‐lactide‐co‐ε‐caprolactone) [P(LLA‐CL)], which is used in biodegradable biomedical materials such as drug‐delivery systems, surgical sutures, orthopedics, and scaffolds for tissue engineering, has been reported to crystallize upon storage in a dry state even at room temperature; this results in rapid changes in the mechanical properties. In biomedical applications, P(LLA‐CL) is used in the presence of water. This study investigated the effects of water on the crystallization of P(LLA‐CL) at 37°C in phosphate buffered solution, which was anticipated to alter its mechanical properties and hydrolytic degradation behavior. Surprisingly, the crystallinity of P(LLA‐CL) in the presence of water rapidly increased in 6–12 h and then slowly increased up to 120 h. The period of time for the initial rapid crystallization increase in the presence of water was much shorter than that in the absence of water. The obtained information would be useful for the selection, preparation, and use of P(LLA‐CL) in various biomedical applications. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Blends of aliphatic polyesters. VIII. Effects of poly(L‐lactide‐co‐ε‐caprolactone) on enzymatic hydrolysis of poly(L‐lactide), poly(ε‐caprolactone), and their blend films

Poly(L ‐lactide), that is, poly(L ‐lactic acid) (PLLA), poly(ε‐caprolactone) (PCL), and their blend (50/50) films containing different amounts of poly(L ‐lactide‐co‐ε‐caprolactone) (PLLA‐CL), were prepared by solution casting. The effects of added PLLA‐CL on the enzymatic hydrolysis of the films were investigated in the presence of proteinase K and Rhizopus arrhizus lipase by use of gravimetry. The addition of PLLA‐CL decreased the proteinase K–catalyzed hydrolyzabilities of the PLLA and PLLA/PCL (50/50) films as well as the Rhizopus arrhizus lipase‐catalyzed hydrolyzability of the PCL and PLLA/PCL (50/50) films. The decreased enzymatic hydrolyzabilities of the PLLA and PCL films upon addition of PLLA‐CL are attributable to the fact that the PLLA‐CL is miscible with PLLA and PCL and the dissolved PLLA‐CL must disturb the adsorption and/or scission processes of the enzymes. In addition to this effect, the decreased enzymatic hydrolyzabilities of the PLLA/PCL (50/50) films upon addition of PLLA‐CL can be explained by the enhanced compatibility between the PLLA‐rich and PCL‐rich phases arising from the dissolved PLLA‐CL. These effects result in decreased hydrolyzable interfacial area for PLLA/PCL films. The decrement in proteinase K–catalyzed hydrolyzability of the PLLA film upon addition of PLLA‐CL, which is miscible with PLLA, was in marked contrast with the enhanced proteinase K–catalyzed hydrolyzability of the PLLA film upon addition of PCL, which is immiscible with PLLA. This confirms that the miscibility of the second polymer is crucial to determine the proteinase K–catalyzed hydrolyzabilities of the PLLA‐based blend films. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 412–419, 2003     

Synthesis and characterization of biodegradable polyurethanes based on L‐cystine/cysteine and poly(ϵ‐caprolactone)

Tunable biodegradable polyurethanes (PUs) with favorable mechanical properties were synthesized from 1,6‐hexamelthylene diisocyanate (HDI) as the hard segment, poly(?‐caprolactone) (PCL) as the soft segment, and L ‐cystine ester as chain extender. The structure of PUs was confirmed by FTIR and ¹H‐NMR. The results of differential scanning calorimeter, thermogravimetric analysis, dynamic mechanical analysis, and tensile test revealed that the thermal and mechanical properties of PUs were strongly influenced by the molecular weight of soft segment PCL. In the presence of glutathione, the disulfide group cleaved into thiols, realizing the PUs degraded and the molecular weight decreased. For PU [550], it remained only 50% of the original M_w. Evaluation of cell viability demonstrated the nontoxicity of the PUs, which facilitated their potential in biomedical applications. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Crystallization and melting behavior of poly(ε‐caprolactone‐co‐δ‐valerolactone) and poly(ε‐caprolactone‐co‐L‐lactide) copolymers with novel chain microstructures

Nuclear magnetic resonance spectroscopy (NMR) characterization of the statistical copolymers of this study showed that the poly(ε‐caprolactone‐co‐L‐lactide)s, with ε‐caprolactone (ε‐CL) molar contents ranging from 70 to 94% and ε‐CL average sequence length (l_CL) between 2.20–9.52, and the poly(ε‐caprolactone‐co‐δ‐valerolactone)s, with 60 to 85% of ε‐CL and l_CL between 2.65–6.08, present semi‐alternating (R→2) and random (R～1) distribution of sequences, respectively. These syntheses were carried out with the aim of reducing the crystallinity of poly(ε‐caprolactone) (PCL), needed to provide mechanical strength to the material but also responsible for its slow degradation rate. However, this was not achieved in the case of the ε‐caprolactone‐co‐δ‐valerolactone (ε‐CL‐co‐δ‐VAL). Non‐isothermal cooling treatments at different rates and isothermal crystallizations (at 5, 10, 21 and 37°C) were conducted by differential scanning calorimetry (DSC), and demonstrated that ε‐CL copolymers containing δ‐valerolactone (δ‐VAL) exhibited a larger crystallization capability than those of L‐lactide (L‐LA) and also arranged into crystalline structures over shorter times. The crystallization enthalpies of the ε‐CL‐co‐δ‐VAL copolymers during the cooling treatments and their heat of fusion (ΔH_m) at the different isothermal temperatures were very large (i.e. ΔH_c > 53 Jg^?1) and in some cases, unrelated to the copolymer composition. In some compositions, such as the 60 : 40, Wide Angle X‐ray Scattering (WAXS) proved that that these two lactones undergo isomorphism and co‐crystallize in a single cell. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42534.     

A dual‐induced self‐expandable stent based on biodegradable shape memory polyurethane nanocomposites (PCLAU/Fe3O4) triggered around body temperature

Concerning the occurrence of in‐stent restenosis and stent thrombosis of stent implantation with balloon angioplasty, a dual‐induced self‐expandable stent based on biodegradable shape memory polyurethane nanocomposites (PCLAU/Fe₃O₄) was developed. The stent could maintain its temporary shape at body temperature for a certain period of time while it was able to recover to its permanent shape at the temperature a little above body temperature (around 40 °C) in both a water bath and an alternating magnetic field. The trigger temperature and remote local heating ensured enough operation time and harmless activation without heating the body tissue. The nanocomposites had high fixing ratios above 99% and recovery ratios above 82% at both 37 and 40 °C. Cytotoxicity and in vitro degradation showed the nanocomposites had good biocompatibility and biodegradability. The PCLAU/Fe₃O₄ nanocomposites with dual‐responsive shape memory effects, desirable mechanical properties, biocompatibility, and biodegradability show great potential for vascular stents. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45686.     

Enhanced crystallization of poly(L‐lactide‐co‐ε‐caprolactone) during storage at room temperature

Copolymer of L ‐lactide and ε‐caprolactone [P(LLA‐CL)] (50/50) was synthesized using stannous octoate and was stored at room temperature. The change in physical properties occurring during this storage at room temperature was investigated by differential scanning calorimetry (DSC), X‐ray diffractometry, polarizing optical microscopy, tensile and bending tests, and light absorbance measurements. It was concluded that the increase in mechanical properties and light absorbance during storage can be ascribed to gradual selective crystallization of the L ‐lactide sequence in P(LLA‐CL) at room temperature. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 947–953, 2000     

Thermo‐ and pH‐ responsive copolymers: Poly(n‐Isopropylacrylamide‐co‐IAM) copolymers

Poly(N‐isopropylacrylamide) (NIPAAm) is well known as a smart material with good thermal sensitivity and favorable biocompatibility. A series of new smart hydrogels, NIPAAm copolymerized with IAM (itaconamic acid; 4‐amino‐2‐methylene‐4‐oxobutanoic acid), were synthesized through radical solution polymerization in this work. Poly(NIPAAm‐co‐IAM) can respond to the changes of temperature as well as pH value. Such a characteristic is due to the fact that IAM contains not only a hydrophilic acrylic acid moiety but also an acrylamide moiety to be thermal and pH sensitive. The experimental results show that the lower critical solution temperature (LCST) of the copolymer increases as the molar fraction of IAM increases. Moreover, based on the current experimental data, 3 wt % of Poly(NIPAAm‐co‐IAM) aqueous solution in this study exhibits a phase transition temperature (37.8°C) close to the human body temperature in the buffer solution of pH 7 possibly to be useful in drug delivery. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42367.     

A Completely Biodegradable Poly[(L‐lactide)‐co‐(ε‐caprolactone)] Elastomer Reinforced by in situ Poly(glycolic acid) Fibrillation: Manufacturing and Shape‐Memory Effects

A new completely biodegradable shape‐memory elastomer consisting of PLLCA reinforced by in situ PGA fibrillation is described. The manufacturing processes and shape‐memory effects of the composites are discussed. DMA results reveal a strong interface interaction between in situ PGA fibrillation and PLLCA. Compared with the SMP‐based composites that are commonly used, the shape‐memory test shows that in situ PGA fibrillation can improve the recovery properties of PLLCA; in fact, the shape‐recovery rate increases from 80.5 to 93.2%.

     

Synthesis and characterization of poly(ϵ‐caprolactone)–poly(L‐lactide) diblock copolymers with an organic amino calcium catalyst

The quasiliving characteristics of the ring‐opening polymerization of ?‐caprolactone (CL) catalyzed by an organic amino calcium were demonstrated. Taking advantage of this feature, we synthesized a series of poly(?‐caprolactone) (PCL)–poly(L ‐lactide) (PLA) diblock copolymers with the sequential addition of the monomers CL and L ‐lactide. The block structure was confirmed by ¹H‐NMR, ¹³C‐NMR, and gel permeation chromatography analysis. The crystalline structure of the copolymers was investigated by differential scanning calorimetry and wide‐angle X‐ray diffraction analysis. When the molecular weight of the PLA block was high enough, phase separation took place in the block copolymer to form PCL and PLA domains, respectively. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 2654–2660, 2006     

Confined crystallization morphology of poly(ϵ‐caprolactone) block within poly(ϵ‐caprolactone)–poly(l‐lactide) copolymers

The confined crystallization of poly(?‐caprolactone) (PCL) block in poly(?‐caprolactone)–poly(l ‐lactide) (PCL‐PLLA) copolymers was investigated using differential scanning calorimetry, polarized optical microscopy, scanning electronic microscopy and atomic force microscopy. To study the effect of crystallization and molecular chain motion state of PLLA blocks in PCL‐PLLA copolymers on PCL crystallization morphology, high‐temperature annealing (180 °C) and low‐temperature annealing (80 °C) were applied to treat the samples. It was found that the crystallization morphology of PCL block in PCL‐PLLA copolymers is not only related to the ratio of block components, but also related to the thermal history. After annealing PCL‐PLLA copolymers at 180 °C, the molten PCL blocks are rejected from the front of PLLA crystal growth into the amorphous regions, which will lead to PCL and PLLA blocks exhibiting obvious fractionated crystallization and forming various morphologies depending on the length of PLLA segment. On the contrary, PCL blocks more easily form banded spherulites after PCL‐PLLA copolymers are annealed at 80 °C because the preexisting PLLA crystal template and the dangling amorphous PLLA chains on PCL segments more easily cause unequal stresses at opposite fold surfaces of PCL lamellae during the growth process. Also, it was found that the growth rate of banded spherulites is less than that of classical spherulites and the growth rate of banded spherulites decreases with decreasing band spacing. © 2019 Society of Chemical Industry     

Preparation and drug release behaviors of 5‐fluorouracil loaded poly(glycolide‐co‐lactide‐co‐caprolactone) nanoparticles

5‐Fluorouracil (5‐Fu) loaded poly(glycolide‐co‐lactide‐co‐caprolactone) (PGLC) nanoparticles were prepared by modified spontaneous emulsification solvent diffusion method (modified‐SESD method) and characterized by dynamic light scattering, scanning electron microscopy and ¹H NMR determination. It was found that the obtained nanoparticles showed near spherical shape and was controllable with the radius range of 30–100 nm. Compared with the nanoparticles prepared by polylactide and poly (lactide‐co‐glycolide) (PLGA) under the similar preparation condition, yield of PGLC nanoparticles was the highest, which reached to about 100%. On the other hand, drug entrapment efficiency of PGLC nanoparticles was also higher than that of PLGA and PLLA nanoparticles. 5‐Fu release behavior of PGLC nanoparticles in vitro showed that 5‐Fu release of PGLC nanoparticles showed a near zero‐order release profile, and 5‐Fu release rate of PGLC nanoparticles was faster than that of PLLA and PLGA nanoparticles. According to degradation behavior of PGLC nanoparticles, it could be proposed that the kinetic of degradation controlled release played an important role in the release process of PGLC nanoparticles. It revealed that the PGLC nanoparticles could be a promising drug carrier. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007