EDM with an Air-Assisted Multi-Hole Rotating Tool

In the present research work, an extensive experimental study of air-assisted rotary electrical discharge machining (AAEDM) of high chromium, high carbon die steel has been made. Investigations have been performed to study the process factor effect namely pulse-on time, discharge current, duty cycle, tool rotation, and air pressure on material removal rate (MRR) and electrode wear ratio (EWR). A comparative analysis of solid rotary tool electrode electrical discharge machining (REDM) and AAEDM has been presented. It was found that a high MRR and low EWR occurred in AAEDM as compared to the REDM process, under the same processing conditions. Use of a multi-hole tool provided better circulation of dielectric in the discharge gap, thus it improved the flushing efficiency of the process. The results showed that the application of compressed air has a favorable influence on MRR and EWR.     

Electrical Discharge Machining (EDM) Characteristics Associated with Electrical Discharge Energy on Machining of Cemented Tungsten Carbide

In this investigation, cemented tungsten carbides graded K10 and P10 were machined by electrical discharge machining (EDM) using an electrolytic copper electrode. The machining parameters of EDM were varied to explore the effects of electrical discharge energy on the machining characteristics, such as material removal rate (MRR), electrode wear rate (EWR), and surface roughness. Moreover, the effects of the electrical discharge energy on heat-affected layers, surface cracks and machining debris were also determined. The experimental results show that the MRR increased with the density of the electrical discharge energy; the EWR and diameter of the machining debris were also related to the density of the electrical discharge energy. When the amount of electrical discharge energy was set to a high level, serious surface cracks on the machined surface of the cemented tungsten carbides caused by EDM were evident.     

Constrained multi-objective optimization of EDM process parameters using kriging model and particle swarm algorithm

This paper investigates the highly nonlinear relationship between process parameters and machining responses, including material removal rate (MRR), surface roughness (SR), and electrode wear rate (EWR) of electric discharge machining (EDM) using Kriging model. Subsequently, an emerging multi-objective optimization algorithm called particle swarm is used to determine the best machining conditions that not only maximize the machining speed but also minimize the EWR with a constraint of the SR. The experiment was carried out with P20 steel on a CNC EDM machine using copper electrode. The research result shows that the MRR increases sharply when increasing the discharge current just like other researches pointed out. However, the relationship between EWR and current is complicated. EWR appears the minimum value when the current is around 30?A. The speed of change of MRR per unit of EWR is the highest when the SR is around 14.5?µm. The combination of Kriging regression model and particle swarm optimization is considered as an intelligent process modeling and optimization of EDM machining. The proper selection of process parameters helps the EDM operator to reduce the machining time and cost.     

Investigation into the Effect of Voltage Excitation of Pre-Ignition Spark Pulse on the Electro-Discharge Machining (EDM) Process

Studying the variation of the electro-discharge machining (EDM) process outputs due to the change in shape of the generated pulse is one research aspect in the EDM process. In this study, the effects of voltage excitation of the pre-ignition spark pulse on the process outputs material removal rate (MRR), electrode wear ratio (EWR), and surface roughness (Ra) have been investigated. Experiments were designed using design of experiments (DOE), and the results were analyzed using analysis of variance (ANOVA). Based on the results, it has become clear that applying voltage excitation of the pulse produces effective pulses, which in turn lessens EWR, increases MRR, and improves surface quality. Hence, the suitability of this method has been verified for EDM.     

Effect of tool rotation in near-dry EDM process on machining characteristics of HSS

Rotary tool near-dry electrical discharge machining (RT-ND-EDM) is a process variant of EDM, which utilizes two phase dielectric medium instead of a conventional liquid or gaseous dielectric medium. The present work, RT-ND-EDM was investigated while machining of high speed steel (AISI M2 grade) using glycerin-air dielectric medium. The effect of various input process parameters was investigated on material removal rate (MRR), surface roughness (SR), and hole overcut (HOC). The input parameters considered were tool rotation speed, current, pulse on time, liquid flow rate, and gas pressure. Experiments were designed and conducted using response surface methodology. Regression models were also developed. The results revealed that the tool rotation speed has a significant effect on MRR, SR, and HOC. FE-SEM micrographs showed that the machined surfaces obtained by RT-ND-EDM have relatively lower micro-cracks, debris accumulation and craters. Also, deep through holes were successfully drilled in 24 mm plate using RT-ND-EDM process.     

Performance analysis of magnetorheological fluid-assisted electrical discharge machining

In this study, a newly developed method of electric discharge machining has been proposed, which uses magnetorheological (MR) fluid instead of conventional oil like kerosene. The paper aims to reveal the process parameters that affect the material removal rate (MRR) during newly developed EDM process. This hybrid machining process showed dual advantage of high-quality machined surface with improved cutting efficiency. The viscoelastic nature of MR fluid is found to give polishing effect as well as high material removal resulting in more stable processing and improved EDM performance. The experimentation has been performed to determine effect of duty cycle, discharge current, pulse on time, percentage concentration of alumina particles surface roughness, and MRR. It has been found that MRR and surface finish improved significantly. The experimental results demonstrated that the EDM process combined with MR fluid resulted in an increase in MRR and surface finish significantly under a certain limit of carbonyl iron percentage (CIPs) in MR fluid.     

Investigation of magnetic field-assisted EDM of composites

The Electrical Discharge Machining (EDM) technique was performed under the magnetic field influence to determine the material removal mechanism as well as surface roughness (SR) of nonmagnetic material. This study presents an exploration of the hybrid EDM technique assisted by magnetic field, with an aim to improve process performance. Herein, magnetic field intensity, peak current, duration of pulse-on/off, tool electrode material, and SiC percentage distribution were opted as the machining parameters. The chosen parameters were analyzed for their effects on the material removal rate (MRR) and SR while machining of SiC-reinforced aluminum-based metal matrix composites. Taguchi methodology was adopted for optimization of process parameters to achieve better MRR and lower SR. The experimental results witnessed improved surface finish and enhanced material removal ability of the process and also inferred that the magnetic field-assisted EDM facilitated the process stability.     

Performance evaluation of Al2O3 nano powder mixed dielectric for electric discharge machining of Inconel 825

Electrical discharge machining (EDM) process is popular for machining conductive and difficult-to-cut materials, but low material removal rate (MRR) and poor surface quality are major limitations of the process. These limitations can be overcome by adding the suitable powder in the dielectric. The powder particles influence electric field intensity during the EDM process which in turn improve its performance. The size (micro to nano) and properties of the mixed powder also influence the machining efficiency. In this regard, the objective of the present work is to study the performance of EDM process for machining Inconel 825 alloy by mixing Al₂O₃ nanopowder in deionized water. The experimental investigation revealed that maximum MRR of 47?mg/min and minimum SR of 1.487?µm, which are 44 and 51% higher in comparison to conventional EDM process, respectively, can be achieved by setting optimal combinations of process parameters. To analyze these observed process behavior, pulse-train data of the spark gap were acquired. The discharge waveform identifies the less arcing phenomenon in the modified EDM process compared to conventional EDM. Further, surface-topography of the machined surface was critically examined by capturing field emission scanning electron microscopy and atomic force microscopy images.     

Electrical Discharge Machining of Functionally Graded 15-35 Vol% SiCp/Al Composites

A functionally Graded 15-35 volume% silicon carbide particulate (SiC_p) reinforced Al359 metal matrix composite (SiC_p/Al MMC) was drilled by electrical discharge machining (EDM) to assess the machinability and workpiece quality. The machining conditions were identified for both the machining performance and workpiece quality of the EDM process, including some aspects of material removal mechanisms, material removal rate (MRR), electrode tool wear, and subsequent drilled hole quality including surface texture and roundness by using surface profilometry, coordinate measuring machine (CMM), and scanning electron microscopy (SEM). It was observed that the material removal rate increases with increasing peak current and pulse-on-time up to the optimal points and drops drastically thereafter. Higher peak current and/or pulse-on-time result in both the greater tool wear and the larger average diameter error. As the percentage of the SiC particles increases, MRR was increased and electrode wear was found to be decreased. At the EDM machined subsurface layer, the fragmented and melted SiC particles were observed under the SEM and EDX-ray examination.     

Influences of Process Parameters on MRR Improvement in Simple and Powder-Mixed EDM of AA6061/10%SiC Composite

In the present work, aluminum alloy 6061/10%SiC composite is machined using numerical controlled Z-axis (ZNC) electrical discharge machining (EDM) process. Improvement in material removal rate (MRR) is explored using tungsten powder suspended dielectric fluid in EDM process (powder-mixed electrical discharge machining (PMEDM)). Peak current, pulse on time, pulse off time, and gap voltage are studied as process parameters. Mathematical relation between process parameters and MRR is established on basis of response surface methodology. The results obtained are further compared with MRR achieved from machining using simple EDM. The existence of tungsten particles in kerosene resulted in 48.43% improvement in MRR. The influence of tungsten powder-mixed dielectric fluid on machined surface is analyzed using scanning electron microscope and energy dispersive spectroscopy (EDS). The results revealed improvement in surface finish and reduction in recast layer thickness with PMEDM. EDS analysis reported presence of tungsten and carbon in recast layer deposited on machined surface.     

Parametric Evaluation on Near-Dry Electric Discharge Machining

Near-dry electric discharge machining (EDM) is an eco-friendly process. It does not produce toxic fumes and consequent health hazards. The near-dry EDM generally utilizes a mixture of two phase (liquid and air) dielectric for machining. This investigation reports the influence of four processing parameters, viz. current, flushing pressure, duty factor, and lift on three responses. The responses measured were material removal rate (MRR), tool wear rate (TWR), and surface roughness (SR). The work material chosen was high speed steel (HSS). Mathematical models have been proposed herein for evaluation of the effect of processing parameters in near-dry EDM. These models were developed using response surface methodology (RSM). The experimental results reveal that the process parameters taken into consideration were significant for MRR. The TWR was negligible in near-dry EDM. This process gives a finer surface finish with thinner recast layer even at higher discharge energies as compared to conventional EDM.     

Effect of Tool Rotation on MRR,TWR, and Surface Integrity of AISI-D3 Steel using the Rotary EDM Process

Electric discharge machining (EDM) is an acclaimed non-conventional machining process that is used for machining of hard or geometrically complex and electrically conductive materials which are extremely difficult to machine by conventional methods. One of the foremost demerits of this process is its very low material removal rate (MRR). For this, researchers have proposed some modifications like; providing rotational motion to the tool or workpiece, mixing of conducting fine powders (such as SiC, Cr, Al, graphite etc.) in the dielectric, providing vibrations to either the tool or the workpiece etc.

The present research examines how the MRR and tool wear rates (TWR) vary with the variation in the tool rotation speed and their effects on the surface integrity of the workpiece. The results obtained clearly indicate that the tool rotation significantly improves the average MRR up to 49%. Moreover, the average surface finish also gets improved by around 9–10% while using the rotational tool EDM. Due to the tool rotation, the recast layer thickness is less for the rotary EDM as compared with the stationary tool EDM process. Furthermore, the micro-cracking on the recast surface of the workpiece is also less for the rotary tool EDM as compared with the stationary tool EDM.     

Performance evaluation of cryogenically assisted electric discharge machining (CEDM) process

The performance of cryogenically assisted electric discharge machining (CEDM) process has been evaluated in the presented research paper. The machining of cryogenically treated (CT) and cryogenically untreated (CUT) AISI D2 tool steel work specimens using cryogenically cooled (CC), CT, and CUT copper electrodes have been performed. The effects of various parameters, namely, workpiece condition, tool condition, nozzle flushing, peak current, duty cycle, pulse duration, and gap voltage, have been studied on the performance indicators, viz. the material removal rate (MRR), tool wear rate (TWR), and surface roughness (SR). The best parametric combinations have been suggested to obtain the desired quality characteristics. The interaction effects among various parameters have also been presented. An increase of approximately 18% in MRR and a reduction of 26% and 11% in TWR and SR, respectively, were observed, during the machining through CEDM in contrast to EDM. The confirmatory experiments suggested that experimental values were in permissible agreement with the predicted values for all the performance measures. Finally, the comparison of the CEDM with that of EDM process, in the light of SEM graphs, has been presented.     

Effect of deep cryotreated tungsten carbide electrode and SiC powder on EDM performance of AISI 304

Abstract

Powder mixed electric discharge machining (PMEDM) is a further advancement of conventional EDM process in which electrically conductive powder is suspended in the dielectric fluid to enhance the material removal rate (MRR) along with the surface quality. Cryotreatment is introduced in this process for improving the cutting tool properties as well as tool life. In this investigation, EDM is performed for the machining of AISI 304 stainless steel using cryotreated double tempered tungsten carbide electrode when SiC powder is suspended in the kerosene dielectric. The influence of process parameters viz. pulse on time, peak current, duty cycle, gap voltage and powder concentration on tool wear rate (TWR), surface roughness (R_a), and MRR has been studied. Metallographic analysis was carried out for the machined surfaces. By the addition of powder concentration and cryotreated double tempered electrode, significant improvement in the machining efficiency has been found out. When cryotreated electrode used MRR, TWR and R_a decreased by 12%, 24% and 13.3%, respectively and when SiC powder used MRR increased by 23.2%, TWR and R_a decreased by about 25% and 14.2%, respectively.     

Electrical discharge machining studies on reactive sintered FeAl

bdElectrical discharge machining (EDM) studies on reactive sintered FeAl were carried out with different process parameters. The metal removal rate and tool removal rate were found to increase with the applied pulse on-time. The surface roughness of machined surface also changed with the applied pulse on-time. XRD analysis of machined surface of sintered FeAl showed the formation of Fe₃C phase during the EDM process. The debris analysis was used to identify the material removal mechanism occurring during the EDM of sintered FeAl.     

Parametric optimization of multiwalled carbon nanotube-assisted electric discharge machining of Al-10%SiCp metal matrix composite by response surface methodology

The demand for miniaturized products having a glossy surface or nano-level surface is increasing exponentially in automobile, aerospace, biomedical, and semiconductor industries. The mirror-like surface finish has generated a need to develop advanced machining processes. The addition of powder particle into electric discharge machining (EDM) oil is considered a promising technique to achieve surface integrity at the miniaturization level. In this research, the Al–10%SiC_p metal matrix composite (MMC) has been machined after mixing the appropriate amount of multiwalled carbon nanotubes (MWCNTs) into the EDM dielectric fluid. An advanced experimental setup has been designed and fabricated in the laboratory for conducting the experiments. This proposed technology is called nano powder mixed electric discharge machining (NPMEDM). The input parameters of NPMEDM are also optimized using central composite rotatable design (CCRD) based on response surface methodology (RSM) in order to obtain the best surface finish and material removal rate (MRR). The MRR has been increased by 38.22% and surface finish has been improved by 46.06% after mixing the MWCNTs into the EDM dielectric fluid. The results indicate that the combination of parameters A5, B5, C5, and D5 might have produced maximum MRR, whereas A1, B1, C1, and D3 have produced minimum surface roughness (SR).     

Examinations concerning the electric discharge machining of AZ91/5B4CP composites utilizing distinctive electrode materials

In this study, investigation has been conducted in the focus of obtaining better surface finish in the electro discharge machining (EDM) of AZ91/5B₄C_p magnesium composites using distinctive sort of anode viz. copper, tungsten–copper, brass, aluminum and 20Gr/AA6061 (GRAL-20) composites. The process parameters, pulse on time and current were performed to research the machining qualities through material removal rate (MRR) and tool wear rate (TWR). The machined composites were examined by optical microscopy (OM) and scanning electron microscopy (SEM). The formation of black spots was observed on machining with copper–tungsten and these black spots were not found when GRAL-20 was used as electrode. Machined with GRAL-20 electrode leads to the increase in spark gap, hence adequate flushing occurs; it eliminates re-melted layers on machined surface results in better surface roughness value. The results revealed that GRAL-20 electrodes posses better MRR followed by copper electrode whereas tungsten–copper exhibits better TWR followed by GRAL-20 electrode.     

On machining of hard and brittle materials using rotary tool micro-ultrasonic drilling process

The present paper reports on a recently developed rotary tool micro-ultrasonic drilling (RT-MUSD) process. The RT-MUSD process was utilized for machining of micro-holes in zirconia, silicon and glasswork materials. The effects of work material properties on the performance characteristics (material removal rate (MRR), depth of hole and hole overcut) of RT-MUSD process were investigated by varying the power rating, rotation speed, abrasive size and slurry concentration. Additionally, machined micro-holes and tool surface were analyzed considering microscopic images. The experimental results revealed that the MRR and depth of hole increased by increasing the power rating. An increase in rotation speed up to 300 rpm, abrasive size up to #1200 mesh and concentration up to 20% increased the MRR, depth of hole and decreased hole overcut. The maximum machining rate and hole overcut were observed during machining of silicon followed by glass and zirconia. The fracture toughness and hardness of the work material affected the MRR and tool wear, respectively. Pure brittle fracture mode of material removal was observed in all the work materials during RT-MUSD process. Eventually, the RT-MUSD process was optimized using desirability approach and a micro-hole of depth 4355 µm was achieved using optimal parameter settings.     

Performance of Additive Mixed Kerosene–Servotherm in Electrical Discharge Machining of Monel 400™

In general, kerosene and commercial grade EDM oils are conventional dielectric fluids in electrical discharge machining (EDM), despite their poor performance measures being major drawbacks. The aim of this study was to develop a dielectric fluid offering good performance measures in the EDM process, by determining the appropriate proportion of kerosene–servotherm and analyzing its performance with and without the additive concentration in EDM of monel 400?. Sixteen samples of kerosene–servotherm of varying proportions were used in this study. The optimum proportion of kerosene–servotherm was found to be 75:25, which resulted in the highest material removal rate (MRR) as compared with tool wear rate (TWR), and surface finish was found to be poorer than when using kerosene alone. In addition, 1 l of kerosene–servotherm concentrated with 6 g of graphite powder (one micron) exhibited substantial improvement in MRR, surface finish, and TWR compared with conventional dielectric fluids. Therefore kerosene–servotherm (75:25) concentrated with 6 g/l of graphite powder can be accepted as a potential dielectric fluid offering high MRR along with enhanced surface finish in EDM.     

Powder Mixed Dielectric: An Approach for Improved Process Performance in EDM

The present study reports the outcome of experiments conducted to investigate the effect of parameters on improvement in the material removal rate (MRR), reduction in the tool wear rate (TWR), and overcut size for commonly used die steels. To overcome some of the shortcomings of electric discharge machining (EDM), an approach of powder mixing in dielectric fluids is adopted to investigate the influence of process parameters. The addition of powders in dielectric improves MRR and lowers TWR significantly. Powder concentration, current, and pulse-on time are three significant factors affecting MRR, TWR, and overcut size. An increase in powder concentration improves the process performance, but is limited by the possibility of arcing at higher concentration. Use of the powder resulted in increased effective spark length causing larger overcut. The problem is acute in trials conducted at high pulse-on duration with high powder concentration that leads to a ragged surface at cut edges. Furthermore, electrode tools with smaller tip included angle resulted in larger profile deviation at the machined surface as compared to trials conducted using tools with higher included angle. Surface morphological changes, grain size, microstrain, and material migration were investigated using SEM, XRD, and EDS analysis and a significant improvement in properties of the machined surface was observed.