Studies on machinability of Al/Si<Subscript>p</Subscript> + SiC<Subscript>p</Subscript> composite materials

This paper presents the experimental results on the machinability of silicon and silicon carbide particles (SiC_p) reinforced aluminium matrix composites (Al/Si_p + SiC_p) during milling process using a carbide tool. The total volume fraction of the reinforcements is 65 vol%. The milling forces, flank wear of the tool and the machined surface quality of composites with different volume fraction of SiC_p were measured during experiments. The machined surfaces of composites were examined through SEM. The results showed that the flexural strength and Vickers hardness are improved when certain volume fraction of silicon particles are replaced by silicon carbide particles with the same volume fraction and particle size and the effect of SiC_p on machinability is optimal when 9 vol% silicon particles in Al/Si_p was replaced by silicon carbide particles with the same volume fraction and the same particle size. Cracks and pits were found on the machined surfaces of composites due to the intrinsic brittleness of silicon particles.     

Investigation of thermal properties of Al–Si matrix reinforced fine SiCp composites

Abstract

The characterisation of thermal expansion coefficient and thermal conductivity of Al–Si matrix alloy and Al–Si alloy reinforced with fine SiC_p (5 and 20 wt-%) composites fabricated by stir casting process are investigated. The results show that with increasing temperature up to 350°C, thermal expansion of composites increases and slowly reduces when the temperature reaches to 500°C. The values of both thermal expansion and conductivity of composites are less than those for Al–Si matrix. Microstructure and particles/matrix interface properties play an important role in the thermal properties of composites. Thermal properties of composites are strongly dependent on the weight percentage of SiC_p.     

Statistical analysis for strength and spatial distribution of reinforcement in SiC particulate reinforced aluminum alloy composites fabricated by die-casting

Statistical analysis for strength and spatial distribution of reinforcement in die-cast SiC_p/Al alloy composites was performed in order to predict the reliability of composites. Microstructural analysis was also done to determine the critical features of the composites. Die-casting was carried out using the preheated die at the casting temperature range of 620–750°C. It was found that the SiC pacticulates were homogeneously dispersed in die-cast Al matrix alloy, resulting from the refinement of dendritic cell size due to rapid cooling rate. The tensile strength of die-cast SiC_p/Al alloy composites was higher than that of die-cast Al matrix alloy. Also, the tensile strength was slightly increased with increasing SiC particulate volume fraction at the casting temperature range of 650–700°C. It was concluded that the die-cast temperatures of 750 and 700°C are optimum condition for the distribution of SiC particulates in consequence of good fluidity of melt for 10 and 20 vol.% SiC_p/Al alloy composites, respectively. However, the strength scattering of composites was increased with increasing SiC particulate volume fraction. For the statistical evaluation of strength, the maximum Weibull modulus of die-cast SiC_p/Al alloy composites, which was obtained at the cast temperature of 700°C, was 29.6 in Al matrix alloy, 22.2 in 10 vol.% SiC_p and 14.2 in 20 vol.% SiC_p, respectively.     

Pressure infiltration casting process and thermophysical properties of high volume fraction SiCp/Al metal matrix composites

Abstract

SiC_p/Al composites containing high volume fraction SiC particles were fabricated using a pressure infiltration casting process, and their thermophysical properties, such as thermal conductivity and coefficient of thermal expansion (CTE), were characterised. High volume fraction SiC particulate preforms containing 50–70 vol.-%SiC particles were fabricated by ball milling and a pressing process, controlling the size of SiC particles and contents of an inorganic binder. 50–70 vol.-%SiC_p/Al composites were fabricated by high pressure infiltration casting an Al melt into the SiC particulate preforms. Complete infiltration of the Al melt into SiC preform was successfully achieved through the optimisation of process parameters, such as temperature of Al melt, preheat temperature of preform, and infiltration pressure and infiltration time after pouring. Microstructures of 50–70 vol.-%SiC_p/Al composites showed that pores resided preferentially at interfaces between the SiC particles and Al matrix with increasing volume fraction of SiC particles. The measured coefficients of thermal expansion of SiC_p/Al composites were in good agreement with the estimated values based on Turner's model. The measured thermal conductivity of SiC_p/Al composites agreed well with estimated values based on the 'rule of mixture' up to 70 vol.-% of SiC particles, while they were lower than the estimated values above 70 vol.-% of SiC particles, mainly due to the residual pores at SiC/Al interfaces. The high volume fraction SiC_p/Al composite is a good candidate material to substitute for conventional thermal management materials in advanced electronic packages due to their tailorable thermophysical properties.     

A review on conventional and nonconventional machining of SiC particle-reinforced aluminium matrix composites

Among the various types of metal matrix composites, SiC particle-reinforced aluminum matrix composites (SiC_p/Al) are finding increasing applications in many industrial fields such as aerospace, automotive, and electronics. However, SiC_p/Al composites are considered as difficult-to-cut materials due to the hard ceramic reinforcement, which causes severe machinability degradation by increasing cutting tool wear, cutting force, etc. To improve the machinability of SiC_p/Al composites, many techniques including conventional and nonconventional machining processes have been employed. The purpose of this study is to evaluate the machining performance of SiC p/Al composites using conventional machining, i.e., turning, milling, drilling, and grinding, and using nonconventional machining, namely electrical discharge machining (EDM), powder mixed EDM, wire EDM, electrochemical machining, and newly developed high-efficiency machining technologies, e.g., blasting erosion arc machining. This research not only presents an overview of the machining aspects of SiC_p/Al composites using various processing technologies but also establishes optimization parameters as reference of industry applications.The full text can be downloaded at https://link.springer.com/article/10.1007/s40436-020-00313-2     

Surface characterization of SiC whisker/2124 aluminium and Al2O3 composites machined by abrasive water jet

The machinability of two classes of high-temperature composites (SiC whisker/2124 aluminium and SiC whisker/Al₂O₃) with an abrasive waterjet (AWJ) was investigated. The as-machined surfaces of the composites were characterized by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), and profilometry to determine the surface finish. Microhardness measurements were also performed on the as-machined metal matrix composites. AWJ appears to be a quite promising machining method due to its fast speed and economical operation. It gives relatively smooth surfaces coupled with minimum subsurface microstructural damage.     

Accumulative press bonding; a novel manufacturing process of nanostructured metal matrix composites

A new manufacturing process for metal matrix composites has been invented, namely accumulative press bonding (APB). The APB process provided an effective method to produce bulk Al/10 vol.% WC_p composite using tungsten carbide (WC) powder and AA1050 aluminum sheets as the raw materials. The microstructural evolutions and mechanical properties of the monolithic aluminum and Al/WC_p composite during various APB cycles were examined by scanning electron microscopy, X-ray diffractometry, X’pert HighScore software, and tensile test equipment. The results revealed that by increasing the number of APB cycles (a) the uniformity of WC particles in aluminum matrix improved, (b) the porosity of the composite eliminated, (c) the particle free zones decreased and (d) the cluster characteristics improved. Hence, the final Al/WC_p composite processed by 14 APB cycles showed a uniform distribution of WC_p throughout the aluminum matrix, strong bonding between particles and matrix, and a microstructure without any porosity and undesirable phases. The X-ray diffraction results also showed that nanostructured Al/WC_p composite with the average crystallite size of 58.4 nm was successfully achieved by employing 14 cycles of APB technique. The tensile strength of the composites enhanced by increasing the number of APB cycles, and reached to a maximum value of 216 MPa at the end of 14th cycle, which is 2.45 and 1.2 times higher than obtained values for annealed (raw material, 88 MPa) and 14 cycles APBed monolithic aluminum (180 MPa), respectively. Though the elongation of Al/WC_p composite lessened during the initial cycles of APB process, it increased at the final cycles of the mentioned process by 78%. Role of WC particles, uniformity of reinforcement, porosity, bonding quality of the reinforcement and matrix, grain refinement, and strain hardening were considered as the strengthening mechanisms in the manufactured composites.     

Development of Al356/SiCp cast composites by injection of SiCp containing composite powders

One of the great challenges of producing cast metal matrix composites is the agglomeration tendency of the reinforcements. This would normally result in poor distribution of the particles, high porosity content, and low mechanical properties. In the present work, a new method for uniform distribution of very fine SiC particles with average size of less than 3 μm was employed. The key idea was to allow for gradual in situ release of properly wetted SiC particles in the liquid metal. For this purpose, SiC particles were injected into the melt in three different forms, i.e., untreated SiC_p, milled particulate Al–SiC_p composite powder, and milled particulate Al–SiC_p–Mg composite powder. The resultant composite slurries were then cast from either fully liquid (stir casting) or semisolid (compocasting) state. Consequently, the effects of the casting method and the type of the injected powder on the microstructural characteristics as well as the mechanical properties of the cast composites were investigated. The results showed that the distribution of SiC particles in the matrix and the porosity content of the composites were greatly improved by injecting milled composite powders instead of untreated-SiC particles into the melt. Casting from semisolid state instead of fully liquid state had similar effects. The average size of SiC particles incorporated into the matrix was also significantly reduced from about 8 to 3 μm by injecting milled composite powders. The ultimate tensile strength, yield strength and elongation of Al356/5 vol.%SiC_p composite manufactured by compocasting of the (Al–SiC_p–Mg)_cp injected melt were increased by 90%, 103% and 135%, respectively, compared to those of the composite manufactured by stir casting of the untreated-SiC_p injected melt.     

Effects of reinforcement distribution on low and high temperature tensile properties of Al356/SiCp cast composites produced by a novel reinforcement dispersion technique

A major challenge for full utilization of the potentials of SiC_p reinforced metal matrix composites is the uniform dispersion of very fine SiC particles in the matrix alloys. In this study, a novel method for gradual in situ release of properly wetted SiC particles with average size of less than 3 μm in the liquid metal was employed which greatly overcame this challenge. SiC particles were injected into the melt in three different forms, i.e., untreated SiC_p, milled particulate Al-SiC_p composite powder, and milled particulate Al-SiC_p-Mg composite powder. The resultant composite slurries were then cast in either a fully liquid state (stir casting) or semisolid state (compocasting). Subsequently, the effects of the type of the injected powder and the casting method on the microstructural and mechanical characteristics of the cast composites at room temperature and 300 °C were investigated. The results demonstrated that distribution of SiC particles in the matrix were greatly improved by injecting milled composite powders instead of untreated SiC particles into the melt. Also casting the composite slurries in a semisolid state instead of fully liquid state slightly improved the distribution. The ultimate tensile strength, yield strength and elongation at room temperature of Al356/5 vol.% SiC_p composite manufactured by compocasting of the (Al-SiC_p-Mg)_cp-injected melt were increased by 113%, 90% and 135%, respectively, compared to those of the composite manufactured by stir casting of the untreated-SiC_p injected melt. The improvements in these properties at 300 °C were about 100%, 103% and 129%, respectively. Almost all the composite samples retained more than 90% of their strengths at 300 °C, whereas the monolithic samples lost more than 25% of their strength at this temperature. The composites manufactured by compocasting of (Al-SiC_p-Mg)_cp-injected melts exhibited a typical ductile fracture surface with equiaxed dimples at both room temperature and 300 °C.     

Incorporation of new technique for processing of Al/SiCp composites based on evaporative pattern casting (EPC) method

Abstract

A336 Al matrix composites containing different volume fraction and mean mass particle size of SiC particles as the reinforcing phase were synthesised by evaporative pattern casting (EPC) route. The process consisted of fabricating of EPS/SiC_p composite pattern followed by EPC of A336 Al alloy. The EPS/SiC_p pattern was made by blending SiC particles with expandable polystyrene (EPS) beads and placing them in expanding mould heating with steam until EPS beads expand completely. Uniform distributed SiC particles around the EPS beads and locally movement of them during pouring and degradation leads to homogenous distribution of particles in final Al/SiC_p composite. Higher modulus, strength and hardness were observed in the composites than the unreinforced Al alloy part. The fracture surfaces of the composite samples exhibited dimple surfaces and fracture in SiC particles.     

Wetting and interfacial reactions in Al-Li-SiCp metal matrix composites processed by spray atomization and deposition

The present study addresses the wetting and interfacial behaviour in a SiC_p reinforced aluminium-lithium alloy processed by spray atomization and deposition. The microstructural characteristics of the spray atomized and deposited Al-Li-SiC_p metal matrix composites were investigated as a function of processing history and thermal exposure. The present results show that there was sufficient interfacial activity at the Al-Li/SiC interface during deposition to establish a stable bond. Furthermore, the absence of interfacial reaction products suggests that the temperature during deposition remained relatively low. When the spray deposited material was exposed to temperatures in excess of 600 °C, severe interfacial reactions and the formation of oxide phases were noted. The microstructural studies were accomplished using optical microscopy, scanning electron microscopy (with energy dispersive X-ray spectroscopy), transmission electron microscopy, and X-ray diffractometry.     

Effect of AlN particles on the corrosion behavior of Al/AlN<Subscript>P</Subscript> composites

The corrosion behavior of Al/AlN_P composites has been examined by using potentiodynamic polarization technique in 3.5wt% NaCl solution with the pH value of 5, 8.6, and 11.6 respectively. Electrochemical impedance spectra (EIS) measurements have also been carried out to assess the long-term effects of AlN particles. It has been found that Al/AlN_p composites show the increased susceptibility to pitting attack compared with the unreinforced Al, which is attributed to the micro-galvanic action between AlN particles and the matrix Al. The micro-galvanic action mainly arises as a result of hydrolysis of AlN particles. In addition, EIS measurements reveal that the corrosion mechanism of Al/AlN_p composites changes a lot with increasing immersion time, which is controlled by diffusion process at last.     

INFLUENCE OF PARTICLE SIZE AND VOLUME FRACTION ON DAMAGE AND FRACTURE IN Al–Al3 Ti COMPOSITES AND MICROMECHANICAL MODELLING USING THE GTN MODEL

Six different Al–Al₃ Ti composites were prepared via the powder metallurgy route. The size and volume fraction of Al₃ Ti particles was varied for a systematic investigation of fracture behaviour. The dominant failure mechanism in the composites is particle fracture and void growth starting from the broken particles. In comparison with the pure Al–matrix, an incorporation of Al₃ Ti particles reduces the crack initiation toughness and reduces the slope of the crack growth resistance curve. The inter-particle distance was found to be the main microstructural parameter controlling the slope of the crack growth resistance curve. The modified Gurson–Tvergaard–Needleman model (GTN model) was applied to one of the composites. The behaviour of tensile specimens could be successfully modelled, whereas the experimentally observed crack propagation in precracked single edge bend specimens [SE(B)] could not be simulated with the GTN model.     

Structure and properties of modified compocast microsilica reinforced aluminum matrix composite

A356 aluminum alloy reinforced with 7 wt.% microsilica composites was produced by the three different processing routes viz. liquid metal stir casting followed by gravity casting, compocasting followed by squeeze casting and modified compocasting route and their properties were examined. Microstructure of liquid metal stir cast Al MMC shows agglomeration of particles leading to high porosity level in the developed material. Adopting new route of compocasting followed by squeeze casting process prevents the agglomeration sites with uniform distribution and dispersion of the dispersoids in the matrix metal. Modified compocasting process reduces the segregation of particles in the final composites thus enhancing the mechanical, tribological and corrosion properties of the composites. Superior wear-resistance properties were exhibited by the modified compocast composite compared to the unreinforced squeeze cast alloy and abrasive type wear mechanism was observed in the case of composite. Increasing the sliding speed resulted in the quick evolution of tribolayer and the wear rate of composite gets reduced. The presence of intermetallic phases like MgAl₂O₄, NaAlSi₃O₈ and KAlSi₃O₈ has a favorable effect on increased corrosion resistance of the composite. Microsilica particles significantly enhanced the compressive strength of modified compocast composites compared to the unreinforced squeeze cast Al alloy.     

Experimental Investigation on Rotary Ultrasonic Face Grinding of SiCp/Al Composites

SiCp/Al composites have been widely used in many fields such as aerospace, automobile, advanced weapon system, etc. But this kind of material, especially with high volume fraction, is difficult to machine due to the reinforced particles existing in matrix, which has limited its further application. Rotary ultrasonic machining (RUM) has many excellent features and it has never been used to machine SiCp/Al composites. In order to improve the machinability and application of SiCp/Al composites, the rotary ultrasonic face grinding experiments of SiCp/Al composites reinforced with 45% volume SiC particles were carried out to investigate cutting force, surface quality, tool wear, and abrasive chip shapes. The experimental results indicate that ultrasonic vibration could reduce cutting force, surface roughness, surface defects, and increase plastic removal ratio. The cutting force could be lowered by an average of 13.86% and the surface roughness could be lowered by an average of 11.53%. The examined results of tool wear patterns suggest that tool wear is mainly caused by grain breakage and grain fall-off. Grinding wheel blockage and grinding burn were not observed in machining process.     

Effect of TiN particulate reinforcement on corrosive behaviour of aluminium 6061 composites in chloride medium

In the present investigation, the corrosive behaviour of Al 6061–TiN particulate composites prepared by liquid metallurgy has been studied in chloride medium using electroanalytical techniques such as Tafel, cyclic polarization and electrochemical impedance spectroscopy (EIS). Surface morphology of the sample electrodes was examined using scanning electron micrography and energy dispersive X-ray methods. X-ray diffraction technique was used to confirm inclusion of TiN particulates in the matrix alloy and identify the alloying elements and intermetallic compounds in the Al 6061 composites. Polarization studies indicate an increase in the corrosion resistance in composites compared to the matrix alloy. EIS study reveals that the polarization resistance (R _p) increases with increase in TiN content in composites, thus confirming improved corrosion resistance in composites. The observed decrease in corrosion rate in the case of composites is due to decoupling between TiN particles and Al 6061 alloy. It is understood that after the initiation of corrosion, interfacial corrosion products may have decoupled the conducting ceramic TiN from Al 6061 matrix alloy thus eliminating the galvanic effect between them.     

Preparation and properties of nano-SiCp/A356 composites synthesised with a new process

Nano-SiC_p reinforced A356 aluminium alloy composites were prepared by solid–liquid mixed casting. Nano-SiC particles 40?nm in diameter were pre-oxidised at 850°C. Millimetre-sized composite granules were then fabricated by milling a mixture of nano-SiC_p and Al powders, and then remelting to form an alloy melt, which was treated by mechanical stirring and ultrasonic vibration to prepare the composites. Results showed that nano-SiC particles were dispersed pretty well within the matrix and no serious agglomeration was observed. As the weight fraction of SiC_p increased, the tensile strength, yield strength and elongation of the composites increased as well, by 22%, 62% and 24%, respectively, when compared to A356 alloy with 2wt-% nano-SiC_p.     

Studies on Machining Parameters While Milling Particle Reinforced Hybrid (Al6061/Al2O3/Gr) MMC

In this article, response surface methodology has been used for finding the optimal machining parameters values for cutting force, surface roughness, and tool wear while milling aluminum hybrid composites. In order to perform the experiment, various machining parameters such as feed, cutting speed, depth of cut, and weight (wt) fraction of alumina (Al₂O₃) were planned based on face-centered, central composite design. Stir casting method is used to fabricate the composites with various wt fractions (5%, 10%, and 15%) of Al₂O₃. The multiple regression analysis is used to develop mathematical models, and the models are tested using analysis of variance (ANOVA). Evaluation on the effects and interactions of the machining parameters on the cutting force, surface roughness, and tool wear was carried out using ANOVA. The developed models were used for multiple-response optimization by desirability function approach to determine the optimum machining parameters. The optimum machining parameters obtained from the experimental results showed that lower cutting force, surface roughness, and tool wear can be obtained by employing the combination of higher cutting speed, low feed, lower depth of cut, and higher wt fraction of alumina when face milling hybrid composites using polycrystalline diamond insert.     

Refining SiCp in reinforced Al–SiC composites using equal-channel angular pressing

Aluminum–silicon carbide composite (Al–SiC_p) is one of the most promising metal matrix composites for their enhanced mechanical properties and wear resistance. In the present study, Al–SiC (average size 55 μm) composites with 5% and 10% by volume were fabricated by stir casting technique. The equal-channel angular pressing (ECAP) was then applied on the cast composites at room temperature in order to study the effect of ECAP passes on the SiC_p size and distribution. The ECAP process was successfully carried out up to 12(8) passes for Al–5%(10%)SiC samples. Microstructure study revealed that the highest refinement by breakage of SiC_p was achieved after the first ECAP pass and that further refinement took place in the next passes. More breakage of the SiC_p was found in the composite richer in reinforcing particles so that the SiC_p reached approximately 1 μm in the Al–10%SiC after 8 passes and 4 μm in Al–5%SiC after 12 ECAP passes. The distribution of SiC reinforcement particles also improved after applying ECAP. The factors including decrease in reinforcing particle size, improvement in their distribution, decrease in porosity in addition to strain hardening and grain refining of the matrix resulted in enhancement of tensile and compressive strengths as well as hardness by more than threefold for the Al–5%SiC after 12 passes and for Al–10%SiC after 8 passes compared to the cast composites. Additionally, the composite remained ductile after the ECAP process. The fracture surface indicated good bond between the matrix and the reinforcement.     

Thermal expansion of a novel hybrid SiC foam–SiC particles–Al composites

A new type of hybrid SiC foam–SiC particles–Al composites (V_SiC = 53, 56.2 and 59.9%) to be used as an electronic packaging substrate material were fabricated by squeeze casting technique, and their thermal expansion behavior was evaluated. The coefficients of thermal expansion (CTEs) of the hybrid composites in the range of 20–100 °C were found to be between 6.6 and 7.7 ppm/°C. The measured CTEs are much lower than those of SiC particle-reinforced aluminum (SiC_p–Al) composites with the same content of SiC because of the characteristic interpenetrating structure of the hybrid composites. A material of such a low CTE is ideal for electronic packaging because of the low thermal mismatch (and therefore, low thermal stresses) between the electronic component and the substrate. To achieve similar CTEs in SiC_p–Al composites, the volume fraction of SiC would be much higher than that in the hybrid composites.