Microstructural Evolution and Mechanical Properties of Nanointermetallic Phase Dispersed Al<Subscript>65</Subscript>Cu<Subscript>20</Subscript>Ti<Subscript>15</Subscript> Amorphous Matrix Composite Synthesized by Mechanical Alloying and Hot Isostatic Pressing

The structure and mechanical properties of nanocrystalline intermetallic phase dispersed amorphous matrix composite prepared by hot isostatic pressing (HIP) of mechanically alloyed Al₆₅Cu₂₀Ti₁₅ amorphous powder in the temperature range 573 K to 873 K (300 °C to 600 °C) with 1.2 GPa pressure were studied. Phase identification by X-ray diffraction (XRD) and microstructural investigation by transmission electron microscopy confirmed that sintering in this temperature range led to partial crystallization of the amorphous powder. The microstructures of the consolidated composites were found to have nanocrystalline intermetallic precipitates of Al₅CuTi₂, Al₃Ti, AlCu, Al₂Cu, and Al₄Cu₉ dispersed in amorphous matrix. An optimum combination of density (3.73 Mg/m³), hardness (8.96 GPa), compressive strength (1650 MPa), shear strength (850 MPa), and Young’s modulus (182 GPa) were obtained in the composite hot isostatically pressed (“hipped”) at 773 K (500 °C). Furthermore, these results were compared with those from earlier studies based on conventional sintering (CCS), high pressure sintering (HPS), and pulse plasma sintering (PPS). HIP appears to be the most preferred process for achieving an optimum combination of density and mechanical properties in amorphous-nanocrystalline intermetallic composites at temperatures ≤773 K (500 °C), while HPS is most suited for bulk amorphous alloys. Both density and volume fraction of intermetallic dispersoids were found to influence the mechanical properties of the composites.     

Evaluating the Diffusion Coefficient of Sulfur in Low-Silica CaO-SiO<Subscript>2</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Slag

The chemical diffusion coefficient of sulfur in the ternary slag of composition 51.5 pct CaO-9.6 pct SiO₂-38.9 pct Al₂O₃ slag was measured at 1680 K, 1700 K, and 1723 K (1403 °C, 1427 °C, and 1450 °C) using the experimental method proposed earlier by the authors. The P_\textS2 P_{{{\text{S}}_{2} }} and P_\textO2 P_{{{\text{O}}_{2} }} pressures were calculated from the Gibbs energy of the equilibrium reaction between CaO in the slag and solid CaS. The density of the slag was obtained from earlier experiments. Initially, the order of magnitude for the diffusion coefficient was taken from the works of Saito and Kawai but later was modified so that the concentration curve for sulfur obtained from the program was in good fit with the experimental results. The diffusion coefficient of sulfur in 51.5 pct CaO-9.6 pct SiO₂-38.9 pct Al₂O₃ slag was estimated to be in the range 3.98 to 4.14 × 10⁻⁶ cm²/s for the temperature range 1680 K to 1723 K (1403 °C to 1450 °C), which is in good agreement with the results available in literature     

Effect of LiF as Sintering Agent on the Densification and Phase Formation in Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-4 Wt Pct Nb<Subscript>2</Subscript>O<Subscript>5</Subscript> Ceramic Compound

Different amounts of LiF were added to an Al₂O₃-4 pct Nb₂O₅ basic ceramic, as sintering agent. Improved new ceramics were obtained with LiF concentrations varying from 0.25 to 1.50 wt pct and three sintering temperatures of 1573 K, 1623 K, and 1673 K (1300 °C, 1350 °C, and 1400 °C). The addition of 0.5 wt pct LiF yielded the highest densification, 94 pct of the theoretical density, in association with a sintering temperature of 1673 K (1400 °C). Based on X-ray diffraction (XRD), this improvement was due not only to the presence of transformed phases, more precisely Nb₃O₇F, but also to the absence of LiAl₅O₈. The preferential interaction of LiF with Nb₂O₅, instead of Al₂O₃, contributed to increase the alumina sintering ability by liquid phase formation. Scanning electron microscopy (SEM) results revealed well-connected grains and isolated pores, whereas the chemical composition analysis by energy dispersive energy (EDX) indicated a preferential interaction of fluorine with niobium, in agreement with the results of XRD. It was also observed from thermal analysis that the polyethylene glycol binder burnout temperature increased for all LiF concentrations. This may be related to the formation of hydrogen bridge bonds.     

Enhancing physical and mechanical properties of Mg using nanosized Al<Subscript>2</Subscript>O<Subscript>3</Subscript> particulates as reinforcement

A magnesium-based composite with 1.1 volume percentage of nanosized Al₂O₃ particulates reinforcement was fabricated using an innovative disintegrated melt deposition technique followed by hot extrusion. Al₂O₃ particulates with an equivalent size of 50 nm were used as reinforcement. Microstructural characterization of the materials revealed grain refinement of magnesium matrix due to incorporation, retention, and uniform distribution of reinforcement. Physical properties characterization revealed that the addition of nano-Al₂O₃ particulates as reinforcement improves the dimensional stability of pure magnesium. Mechanical properties characterization revealed that the presence of nano-Al₂O₃ particulates as reinforcement leads to a significant increase in microhardness, dynamic elastic modulus, 0.2 pct yield strength (YS), ultimate tensile strength (UTS), and ductility of pure magnesium. The results revealed that the combined tensile properties of these materials are superior when compared to Mg reinforced with much higher volume percentage of SiC. An attempt is made in the present study to correlate the effect of nano-Al₂O₃ particulates as reinforcement with the microstructural, physical, and mechanical properties of magnesium.     

<Emphasis Type="Italic">In-Situ</Emphasis> Synthesis of Cu/Cr-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Nanocomposite by Mechanical Alloying and Heat Treatment

In this article, a novel method has been used to prepare a copper matrix nanocomposite containing Cu-10 wt pct Cr-10 wt pct Al₂O₃ by heat treatment of the mechanically activated Cu, Al, and Cr₂O₃ powder mixture. Structural evolutions were investigated using the X-ray diffraction (XRD) technique. The microstructure of samples was examined using scanning electron microscopy (SEM). It was found that during the milling process, Cu(Al) solid solution and Cu₉Al₄ phase were formed as the intermediate products, and therefore, Al activity was decreased. Hence, the reduction of Cr₂O₃ with Al was prevented during the ball milling stage. Further heat treatment carried out under argon atmosphere at 900 °C for 8 hours resulted in completion of Cr₂O₃ reduction by Al.     

Effect of Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Concentration on Density and Structure of (CaO-SiO<Subscript>2</Subscript>)-xAl<Subscript>2</Subscript>O<Subscript>3</Subscript> Slag

The effect of Al₂O₃ concentration on the density and structure of CaO-SiO₂-Al₂O₃ slag was investigated at multiple Al₂O₃ mole percentages and at a fixed CaO/SiO₂ ratio of 1. The experiments were conducted in the temperature range of 2154 K to 2423 K (1881 °C to 2150 °C) using the aerodynamic levitation technique. In order to understand the relationship between density and structure, structural analysis of the silicate melts was carried out using Raman spectroscopy. The density of each slag sample investigated in this study decreased linearly with increasing temperature. When the Al₂O₃ content was less than 15 mole pct, density decreased with increasing Al₂O₃ content due to the coupling of Si (Al), whereas above 20 mole pct density of the slag increased due to the role of Al³⁺ ion as a network modifier.     

Effect of Firing Temperature and Reducing Gas Composition during Low-Temperature Reduction of Nanocrystalline Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>

Pure nanocrystalline hematite (40 to 100 nm) compacts were prepared and sintered at various temperatures (300 °C to 600 °C) and then reduced with 100 pct H₂ at 500 °C. On the other hand, fired compacts at 500 °C were reduced with a H₂-Ar gas mixture containing different concentration of hydrogen (100, 75, 50, and 25 pct) at 500 °C using thermogravimetric techniques. Nanocrystalline Fe₂O₃ compacts were characterized before and after reduction with X-ray diffraction, scanning electron microscopy (SEM), vibrating sample magnetometer (VSM), and reflected light microscope. It was found that the fired compacts at 400 °C to 600 °C have relatively faster reaction behaviors compared to that at lower firing temperature 300 °C. By decreasing the firing temperature to 300 °C, partial sintering with grain growth was observed clearly during reduction. Also, it was found that the reduction rate increased with increasing hydrogen content in the reducing gas. Comparatively, grain growth and partial coalescence took place during reduction with 25 pct H₂ due to long reaction time.

---

Investigation into the solubility of nanopowders of the ZrO<Subscript>2</Subscript>–Y<Subscript>2</Subscript>O<Subscript>3</Subscript>–CeO<Subscript>2</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> system in the aqueous medium at various pH

Nanopowders of ZrO₂–Y₂O₃–CeO₂ and ZrO₂–Y₂O₃–CeO₂–Al₂O₃ systems are investigated with the purpose of studying the influence of pH of the dispersed medium on the solubility of nanopowder particles of a complex composition in an aqueous medium after membrane filtration and centrifugation to further prepare the stable dispersions necessary for toxicological investigations of nanoparticles. Concentrations of elements remaining in a supernatant after the sample preparation, which includes membrane filtration and centrifugation, are measured by inductively coupled plasma optical emission spectroscopy. It is established that that the largest aggregative stability of the nanopowder dispersion without the Al₂O₃ additive corresponds to the optimal range of pH 5.5–9.5, while with the Al₂O₃ additive, it is region pH 7.0. The results evidence that, when dispersing these powders, the hydrosol of yttrium oxyhydroxide, which is dissolved at pH < 6.0, is formed. When dissolving in water of the powder with the Al₂O₃ additive in the neutral medium, aluminum hydroxide is formed; in the acidic medium (pH < 6), it is replaced by main soluble aluminum salts; and in the alkali medium (pH > 7), amphoteric aluminum hydroxide is dissolved because of the formation of aluminates.     

Thermodynamics of MnO-SiO<Subscript>2</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-MnS Liquid Oxysulfide: Experimental and Thermodynamic Modeling

The activities of MnO and MnS in a MnO-SiO₂-Al₂O₃(or AlO_1.5)-MnS liquid oxysulfide solution were investigated by employing the gas/liquid/Pt-Mn alloy chemical equilibration technique under a controlled atmosphere at 1773 K (1500 °C). Also, the sulfide capacity, defined as C _S = (wt pct S)(pO₂/pS₂)^1/2, in MnO-SiO₂-Al₂O₃ slag with a dilute MnS concentration was obtained from the measured experimental data. As X _SiO2/(X _MnO + X _SiO2) in liquid oxysulfide increases, the activity coefficient of MnO decreases, while that of MnS first increases and then decreases. As X(AlO_1.5) in liquid oxysulfide increases, the activity coefficient of MnS increases, while no remarkable change is observed for the activity coefficient of MnO. The behavior of the activity coefficient of MnS was qualitatively analyzed by considering MnO + A _x S _y (SiS₂ or Al₂S₃) = MnS + A _x O _y (SiO₂ or Al₂O₃) reciprocal exchange reactions in the oxysulfide solution. The behavior was shown to be consistent with phase diagram data, namely, the MnS saturation boundary. Quantitative analysis of the activity coefficient of the oxysulfide solution was also carried out by employing the modified quasichemical model in the quadruplet approximation.     

Effect of Superficially Applied Y<Subscript>2</Subscript>O<Subscript>3</Subscript> Coating on High-Temperature Corrosion Behavior of Ni-Base Superalloys

Inhibitors and oxide additives have been investigated with varying success to control high-temperature corrosion. Effect of Y₂O₃ on high-temperature corrosion of Superni 718 and Superni 601 superalloys was investigated in the Na₂SO₄-60 pct V₂O₅ environment at 1173 K (900 °C) for 50 cycles. Y₂O₃ was applied as a coating on the surfaces of the specimens. Superni 601 was found to have better corrosion resistance in comparison with Superni 718 in the Na₂SO₄-60 pct V₂O₅ environment. The Y₂O₃ superficial coating was successful in decreasing the reaction rate for both the superalloys. In the oxide scale of the alloy Superni 601, Y and V were observed to coexist, thereby indicating the formation of a protective YVO₄ phase. There was a distinct presence of a protective Cr₂O₃-rich layer just above the substrate/scale interface in the alloy. Whereas Cr₂O₃ was present with Fe and Ni in the scale of Superni 718. Y₂O₃ seemed to be contributing to better adhesion of the scale, as comparatively lesser spalling was noticed in the presence of Y₂O₃.     

Effect of heat treatments on <Emphasis Type="Italic">In-Situ</Emphasis> Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/TiAl<Subscript>3</Subscript> composites produced from squeeze casting of TiO<Subscript>2</Subscript>/A356 composites

In-situ Al₂O₃/TiAl₃ intermetallic matrix composites were fabricated via squeeze casting of TiO₂/A356 composites heated in the temperature range from 700 °C to 780 °C for 2 hours. The phase transformation in TiO₂/A356 composites employing various heat-treatment temperatures (700 °C to 780 °C) was studied by means of differential thermal analysis (DTA), microhardness, scanning electron microscopy (SEM), electron probe microanalysis (EPMA), and X-ray diffraction (XRD). From DTA, two exothermic peaks from 600 °C to 750 °C were found in the TiO₂/A356 composites. The XRD showed that Al₂O₃ and TiAl₃ were the primary products after heat treatment of the TiO₂/A356 composite. The fabrication of in-situ Al₂O₃/TiAl₃ composites required 33 vol pct TiO₂ in Al and heat treatment in the range from 750 °C to 780 °C. The hardness (HV) of the in-situ Al₂O₃/TiAl₃ composites (1000 HV) was superior to that of nonreacted TiO₂/A356 composites (200 HV). However, the bending strength decreased from 685 MPa for TiO₂/A356 composites to 250 MPa for Al₂O₃/TiAl₃ composites. It decreased rapidly because pores occurred during the formation of Al₂O₃ and TiAl₃. The activation energy of the formation of Al₂O₃ and TiAl₃ from TiO₂ and A356 was determined to be about 286 kJ/mole.     

Phase-equilibrium data and liquidus for the system “MnO”-CaO-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-SiO<Subscript>2</Subscript> at Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/SiO<Subscript>2</Subscript> of 0.55 and 0.65

Phase-equilibrium data and liquidus isotherms for the system “MnO”-CaO-(Al₂O₃+SiO₂) at silicomanganese alloy saturation have been determined in the temperature range of 1373 to 1723 K. The results are presented in the form of the pseudoternary sections “MnO”-CaO-(Al₂O₃+SiO₂) with Al₂O₃/SiO₂ weight ratios of 0.55 and 0.65. The primary-phase fields have been identified in this range of conditions.     

Amphoteric behavior of alumina in viscous flow and structure of CaO-SiO<Subscript>2</Subscript> (-MgO)-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> slags

The viscosity of CaO-SiO₂ (-MgO)-Al₂O₃ slags was measured to clarify the effects of Al₂O₃ and MgO on the structure and viscous flow of molten slags at high temperatures. Furthermore, the infrared spectra of the quenched slags were analyzed to understand the structural role of Al₂O₃ in the polymerization or depolymerization of silicate network. The Al₂O₃ behaves as an amphoteric oxide with the composition of slags; that is, the alumina behaves as a network former up to about 10 mass pct Al₂O₃, while it acts as a network modifier, in parts, in the composition greater than 10 mass pct Al₂O₃. This amphoteric role of Al₂O₃ in the viscous flow of molten slags at the Newtonian flow region was diminished by the coexistence of MgO. The effect of Al₂O₃ on the viscosity increase can be understood based on an increase in the degree of polymerization (DOP) by the incorporation of the [AlO₄]-tetrahedra into the [SiO₄]-tetrahedral units, and this was confirmed by the infrared (IR) spectra of the quenched slags. The influence of alumina on the viscosity decrease can be explained on the basis of a decrease in the DOP by the increase in the relative fraction of the [AlO₆]-octahedral units. The relative intensity of the IR bands for the [SiO₄]-tetrahedra with low NBO/Si decreased, while that of the IR bands for [SiO₄]-tetrahedra with high NBO/Si increased with increasing Al₂O₃ content greater than the critical point, i.e., about 10 mass pct in the present systems. The variations of the activity coefficient of slag components with composition indirectly supported those of viscosity and structure of the aluminosilicate melts.     

Processing,microstructure, and mechanical properties of cast <Emphasis Type="Italic">in-Situ</Emphasis> Al(Mg,Mn)-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>(MnO<Subscript>2</Subscript>) composite

Cast particulate composites, containing in-situ generated reinforcing particles of alumina, have been developed by solidification of slurry obtained by dispersion of externally added manganese dioxide particles (MnO₂) in molten aluminum, and alumina is formed by reaction of manganese dioxide with molten aluminum. The chemical reaction also releases manganese into molten aluminum. Magnesium is added to the melt in order to help wetting of alumina particles by molten aluminum and to retain the particles inside the melt. The present work aims to understand the influence of key parameters such as processing temperature, time, and the amount of MnO₂ particles added on the microstructure and mechanical properties of the resulting cast in-situ composites. The sequence of addition of MnO₂ particles and magnesium has significant influence on the microstructure and mechanical properties. Increasing processing temperature and time increases the extent of reduction of MnO₂ particles, generating more alumina particles as well as releasing more manganese to the matrix alloy. Alumina helps to nucleate finer and sometimes blocky MnAl₆ in the matrix of the composite and thereby results in relatively higher ductility and increased strength in the composite as compared to the base alloy of similar composition. Even in the presence of relatively higher porosity of 8 to 9 vol pct, one observes a percent elongation not below 7 to 8 pct, which is considerably higher than those observed in cast Al(Mg)-Al₂O₃ composite synthesized by externally added alumina particles.