Microwave Dielectric Properties of CaTiO3-CaAl1/2Nb1/2O3 Ceramics Doped with Li3NbO4

The microwave dielectric properties of CaTi_{1− x} (Al_1/2Nb_1/2) _x O₃ solid solutions (0.3 ≤ x ≤ 0.7) have been investigated. The sintered samples had perovskite structures similar to CaTiO₃. The substitution of Ti⁴⁺ by Al³⁺/Nb⁵⁺ improved the quality factor Q of the sintered specimens. A small addition of Li₃NbO₄ (about 1 wt%) was found to be very effective for lowering sintering temperature of ceramics from 1450–1500° to 1300°C. The composition with x = 0.5 sintered at 1300°C for 5 h revealed excellent dielectric properties, namely, a dielectric constant (ɛ_r) of 48, a Q × f value of 32 100 GHz, and a temperature coefficient of the resonant frequency (τ_f) of −2 ppm/K. Li₃NbO₄ as a sintering additive had no harmful influence on τ_f of ceramics.     

Binary Titania-Silica Glasses Containing 10 to 20 Wt% TiO2

A series of glasses in the TiO₂-SiO₂ system was prepared by the flame hydrolysis boule process. Clear glasses containing as much as 16.5 wt% TiO₂ were obtained. More TiO₂ caused opacity due to phase separation and anatase/rutile crystallization during glass boule formation. Glasses in the 12 to ∼17 wt% TiO₂ range were metastable and showed structural rearrangements on heat treatment at temperatures as low as 750CEC (∼200° below the annealing point). These changes were accompanied by large changes in thermal expansion. Thermal treatment can be designed to produce almost any desired expansion between α_-200+700=−5 × 10^-7/°C and +10 × 10^-7/°C. Zero expansion between 0 and 550°C was obtained. Evidence that these changes are due to phase separation and anatase formation is presented. Viscosity data in the glass transition range, refractive index, and density are also presented.     

Annealing of Irradiation-Induced Thermal Conductivity Changes in ThO2-1.3 wt% UO2

The thermal conductivities of sintered pellets of ThO₂-1.3 wt% U0₂ were measured at 60°C before and after irradiation. The irradiation temperature was below 156°C, and the exposures varied from 3.1 × 10¹⁴ to 4.7 × lo^L7 fissions/cm³. Each fission fragment damaged a region of 2.2 × 10^-16 cm³ with the reduction in conductivity saturating by about 10¹⁷ fissions/cm³. Samples having exposures from 10¹⁵ to 10¹⁶ fissions/cm³ were annealed isothermally at 651 °C or isochronally from 300° to 1200° C to study the annealing of damage. Most of the annealing occurred between 500° and 900°C. The width of this interval plus the slow isothermal annealing suggest that the damage is annealed by a number of single order processes with a spectrum of activation energies from 1.8 to 3.9 eV or, less probably, by a high order process with an activation energy of 3.55 ± 0.4 eV.     

Solubilities of Magnesia, Titania, and Magnesium Titanate in Aluminum Oxide

On heat treatment in air the solubility of MgO or TiO₂, in Al₂₃ is too small to detect by lattice parameter shifts. The solubility of MgTiO₃ in Al₂O₃ in air increased to the measured values, expressed as atomic fractions Mg:A1or Ti:A1of0.82 × lo-², 1.43 × 10^-2, and 1.75 × 10^-2 at 1250°, 1650°, and 1850°C, respectively. In 1 atm hydrogen the TiO₂ solubility expressed as the atomic fraction Ti:A1 is 0.55 × lo^-2, 0.75 × 10W², 1.15 × 10^-2, and 1.50 × 10^p2 at 1400°, 1500°, 1600°, and 1700°C, respectively. The increased solubility in H₂ was attributed to reduction of the titanium ion. The solubility of MgO in A1₂O₃ in vacuum (0.3μ) expressed as the atomic fraction Mg:A1 was measured as 1.10 × loW⁴, 3.00 × 10"⁴, 6.80 × 10–⁴, and 1.40 × 10^-3 at 1530°, 1630°, 1730°, and 183O°C, respectively. These contents did not cause an observable change in lattice parameter, but a slight change was observed when MgO was dissolved in A1₂O₃ in a hydrogen atmosphere.     

Effect of V2O5 Doping on the Sintering and Dielectric Properties of M-Phase Li1+x−yNb1−x−3yTix+4yO3 Ceramics

The effect of the addition of V₂O₅ on the structure, sintering and dielectric properties of M -phase (Li_{1+ x − y} Nb_{1− x −3 y} Ti _x +4 _y )O₃ ceramics has been investigated. Homogeneous substitution of V⁵⁺ for Nb⁵⁺ was obtained in LiNb_{0.6(1− x )}V_{0.6 x} Ti_0.5O₃ for x ≤ 0.02. The addition of V₂O₅ led to a large reduction in the sintering temperature and samples with x = 0.02 could be fully densified at 900°C. The substitution of vanadia had a relatively minor adverse effect on the microwave dielectric properties of the M -phase system and the x = 0.02 ceramics had [alt epsilon]_r= 66, Q × f = 3800 at 5.6 GHz, and τ_f= 11 ppm/°C. Preliminary investigations suggest that silver metallization does not diffuse into the V₂O₅-doped M -phase ceramics at 900°C, making these materials potential candidates for low-temperature cofired ceramic (LTCC) applications.     

Concurrent Measurement of Volume, Grain-Boundary, and Surface Diffusion Coefficients in the System NiO-Al2O3

Surface, grain-boundary, and volume inter diffusion coefficients for the NiO-Al₂O₃ system were measured concurrently by using a diffusion couple consisting of an A1₂O₃ bicrystal and an NiO single crystal. The A1₂O₃ bicrystals having various tilt angles were fabricated by firing 2 single crystals to be joined in an H₂ atmosphere at 1800°C for 30 h. Diffusion profiles over the surface, along the grain boundary, and in the bulk of the bicrystal were determined with an electron probe microanalyzer. Mathematical analysis of the diffusion profiles gives D _s = 7.41×10^-2 exp (-35,200/ RT ), D _gb = 2.14×10^-1 exp (-63,100/ RT ) (tilt angle =30°), and D _v = 1.26×10⁴ exp (-104,000/ RT ). The grain-boundary diffusion coefficient increases with the mismatch at the boundary.     

Reduced Dielectric Loss of Modified ZnNb2O6 Ceramics by Substituting Nb5+ with Ta5+

The effects of substituting Nb⁵⁺ with Ta⁵⁺ on the microwave dielectric properties of the ZnNb₂O₆ ceramics were investigated in this study. The forming of Zn(Nb_{1− x} Ta _x )₂O₆ ( x =0–0.09) solid solution was confirmed by the measured lattice parameters and the EDX analysis. By increasing x , not only could the Q × f of the Zn(Nb_{1− x} Ta _x )₂O₆ ( x =0–0.09) solid solution be tremendously boosted from 83 600 GHz at x =0 to a maximum 152 000 GHz at x =0.05, the highest ɛ_r∼24.6 could also be achieved simultaneously. It was mainly due to the uniform grain morphology and the highest relative density of the specimen. A fine combination of microwave dielectric properties (ɛ_r∼24.6, Q × f ∼152 000 GHz at 8.83 GHz, τ_f∼–71.1 ppm/°C) was achieved for Zn(Nb_0.95Ta_0.05)₂O₆ solid solution sintered at 1175°C for 2 h.     

Identification of BaO. A12O3.5TiO2 in the Ternary System BaO. A12O3-TiO2

A new identification and indexing for the phase BaAl₂Ti₅O₁₄ were accomplished using an X-ray diffraction technique. The new lattice parameters for the tetragonal lattice structure are: a₀=9.990 × 10^-10 m and c₀=12.264 × 10^-10 m, with a corresponding volume 1.224 × 10^-27 m³. The data provided by the Joint Committee on Powder Diffraction Standards are inconsistent both in lattice parameter values and Miller indices. The X-ray powder diffraction pattern of BaAl₂Ti₅O₁₄ was indexed using the LSUCR (least-squares unit cell refinement) computer program.     

High-Temperature Mechanical Properties of Ceramic Materials: V, (Zn0.65, Mg0.35)2SiO4

The composition (0.65Zn,0.35Mg)₂ SiO₁ was investigated. Its thermal expansion was 32 × 10^-7/°C from room temperature to 1000°C. Modulus of rupture was approximately 7000 psi between room temperature and 800°C, whereas Young's modulus held at approximately 11 × 10° psi over the same range. The substitution of 0.35 m oles Mg⁺⁺ for Zn⁺⁺ in Zn₂Si0₄ causes little change in many of the physical properties, but the solid solution sinters much more readily than pure Zn₂Sio₄. The willemite solid solution studied has very good thermal shock resistance between room temperature and 1000°C.     

Thermal Expansion of the Low-Temperature Form of BaB2O4

Thermal expansion of the low-temperature form of BaB₂O₄ (β-BaB₂O₄) crystal has been measured along the principal crystallographic directions over a temperature range of 9° to 874°C by means of high-temperature X-ray powder diffraction. This crystal belongs to the trigonal system and exhibits strongly anisotropic thermal expansions. The expansion along the c axis is from 12.720 to 13.214 Å (1.2720 to 1.3214 nm), whereas it is from 12.531 to 12.578 Å (1.2531 to 1.2578 nm) along the a axis. The expansions are nonlinear. The coefficients A, B , and C in the expansion formula L _t = L ₀(1 + At + Bt ²+ Ct ³) are given as follows: a axis, A = 1.535 × 10⁻⁷, B = 6.047 × 10⁻⁹, C = -1.261 × 10⁻¹²; c axis, A = 3.256 × 10⁻⁵, B = 1.341 × 10⁻⁸, C = -1.954 × 10⁻¹²; and cell volume V, A = 3.107 × 10⁻⁵, B = 3.406 × 10⁻⁸, C = -1.197 × 10⁻¹¹. Based on α _t = (d L _t /d t )/ L ₀, the thermal expansion coefficients are also given as a function of temperature for the crystallographic axes a , c , and cell volume V.     

Thermal Expansion of 12CaO°7Al2O3

Literature data for the 12CaO°7Al₂O₃ phase show certain discrepancies in the structure, thermal stability, and mean linear thermal expansion obtained by different techniques. Phase-pure, cubic, polycrystallin I2CaO°7Al₂O₃ was synthesized by annealing a stoichiometric melt in air. Infrared spectrophotometry indicated stabilization by moisture. Differential thermal analysis and thermogravimetric analysis showed the cubic phase to be stable up to at least 1200° C. High-temperature X-ray diffraction analysis of a polycrystalline sample and dilatometric measurement of sintered pellets indicated a linear thermal expansion of 41 × 10^-7 to 43X10^-7/°C in the temperature range 200° to 800°C.     

High-Temperature Defect Structure of Cobalt-Doped α-Alumina

Room-temperature optical absorption spectra, electron spin resonance spectra at 15° to 18°K, electrical conductivity, and emf measurements on concentration cells at 1620°C are analyzed and used to determine the defect structure of Codoped α-Al₂O₃. The crystals are mixed ionic and electronic conductors at 1620°C: ionic conduction occurs at 10^-8 atm< p O₂ < 10_-3 atm, with triply charged interstitial Al ions as the major charge carriers, and electronic conduction occurs at 10^-3 atm < p O₂ < 1 atm, with holes as the major charge carriers. A defect model based on the charge compensation of divalent Co at Al sites by triply charged Al interstitials is proposed. The mobilities and activation energy of ions and holes, the oscillator strengths of Co²⁺ and Co³⁺ absorption bands, parameters for electron spin resonance spectra, level positions of substitutional Co²⁺ and an unknown donor, and equilibrium constants for defect formation reactions are determined.     

Effect of CuO on the Sintering Temperature and Piezoelectric Properties of (Na0.5K0.5)NbO3 Lead-Free Piezoelectric Ceramics

When a small amount of CuO was added to (Na_0.5K_0.5)NbO₃ (NKN) ceramics sintered at 960°C for 2 h, a dense microstructure with increased grains was developed, probably due to liquid-phase sintering. The Curie temperature slightly increased when CuO exceeded 1.5 mol%. The Cu²⁺ ion was considered to have replaced the Nb⁵⁺ ion and acted as a hardener, which increased the E _c and Q _m values of the NKN ceramics. High piezoelectric properties of k _p=0.37, Q _m=844, and ɛ₃ ^T /ɛ₀=229 were obtained from the specimen containing 1.5 mol% of CuO sintered at 960°C for 2 h.     

Anisotropic Thermal Expansion of β-Ca2SiO4 Monoclinic Crystal

Crystals of β-Ca₂SiO₄ (space group P 12₁/ n 1) were examined by high-temperature powder X-ray diffractometry to determine the change in unit-cell dimensions with temperature up to 645°C. The temperature dependence of the principal expansion coefficients (α_i) found from the matrix algebra analysis was as follows: α₁= 20.492 × 10⁻⁶+ 16.490 × 10⁻⁹ ( T - 25)°C⁻¹, α₂= 7.494 × 10⁻⁶+ 5.168 × 10⁻⁹( T - 25)°C⁻¹, α₃=−0.842 × 10⁻⁶− 1.497 × 10⁻⁹( T - 25)°C⁻¹. The expansion coefficient α₁, nearly along [302] was approximately 3 times α₂ along the b -axis. Very small contraction (α₃) occurred nearly along [     01]. The volume changes upon martensitic transformations of β↔α_L' were very small, and the strain accommodation would be almost complete. This is consistent with the thermoelasticity.     

Thermal Expansion Behavior of Titanium-Doped La(Sr)CrO3 Solid Oxide Fuel Cell Interconnects

La_0.8Sr_0.2Cr_0.9Ti_0.1O₃ perovskite has been designed as an interconnect material in high-temperature solid oxide fuel cells (SOFCs) because of its thermal expansion compatibility in both oxidizing and reducing atmospheres. La_0.8Sr_0.2Cr_0.9Ti_0.1O₃ shows a single phase with a hexagonal unit cell of a = 5.459(1) Å, c = 13.507(2) Å, Z = 6 and a space group of R -3 C . Average linear thermal expansion coefficients of this material in the temperature range from 50° to 1000°C were 10.4 × 10⁻⁶/°C in air, 10.5 × 10⁻⁶/°C under a He–H₂ atmosphere (oxygen partial pressure of 4 × 10⁻¹⁵ atm at 1000°C), and 10.9 × 10⁻⁶/°C in a H₂ atmosphere (oxygen partial pressure of 4 × 10⁻¹⁹ atm at 1000°C). La_0.8Sr_0.2Cr_0.9Ti_0.1O₃ perovskite with a linear thermal expansion in both oxidizing and reducing environments is a promising candidate material for an SOFC interconnect. However, there still remains an air-sintering problem to be solved in using this material as an SOFC interconnect.     

Thermal, Mechanical, and Chemical Properties of Sintered Xenotime-Type RPO4 (R = Y, Er, Yb, or Lu)

Xenotime-type RPO₄ (R = Y, Er, Yb, or Lu) powder was dry-pressed into disks and bars. The disks and bars could be sintered to a relative density of greaterthan equal to98% in air without cracking at 1300° (R = Yb or Lu) or 1500°C (R = Y or Er), depending on the grain size. The linear thermal expansion coefficient (at 1000°C), thermal conductivity (at 20°C), and bending strength (at 20°C) of the xenotime-type RPO₄ ceramics were 6.2 10^-6/°C, 12.02 W(mK)^-1, and 95 ± 29 MPa for R = Y; 6.0 10^-6/°C, 12.01 W(mK)^-1, and 100 ± 21 MPa for R = Er; 6.0 10^-6/°C, 11.71 W(mK)^-1, and 135 ± 34 MPa for R = Yb; and 6.2 10^-6/°C, 11.97 W(mK)^-1, and 155 ± 25 MPa for R = Lu. The xenotime-type RPO₄ ceramics did not react with SiO₂, TiO₂, Al₂O₃, ZrO₂, or ZrSiO₄, even at 1600°C for 3 h in air, and were stable in aqueous solutions of HCl, H₂SO₄, HNO₃, NaOH, and NH₄OH at 20°C.     

Raman and 11B Nuclear Magnetic Resonance Spectroscopic Studies of Alkaline-Earth Lanthanoborate Glasses

Glasses from the RO.La₂O₃.B₂O₃ (R = Mg, Ca, and Ba) systems have been examined. Glass formation is centered along the metaborate tie line, from La(BO₂)₃ to R(BO₂)₂. Glasses generally have transition temperatures >60°C and expansion coefficients between 60 × 10^-7/°C and 100 × 10^-7/°C. Raman and solid-state nuclear magnetic resonance spectroscopies reveal changes in the metaborate network that depend on both the [R]:[La] ratio and the type of alkaline-earth ion. The fraction of tetrahedral sites is generally reduced in alkaline-earth-rich glasses, with magnesium glasses possessing the lowest concentration of B[4]. Raman spectra indicate that, with increasing [R]:[La] ratio, the preferred metaborate anion changes from a double-chain structure associated with crystalline La(BO₂)₃ to the singlechain and ring metaborate anions found in crystalline R(BO₂)₂ phases. In addition, disproportionation of the metaborate anions leads to the formation of a variety of other species, including pyroborates with terminal oxygens and more-polymerized species, such as diborates, with tetrahedral borons. Such structural changes are related to the ease of glass formation and some of the glass properties.     

Thermal Expansion of YBa2Cu3O7_xas Determined by High-Temperature X-ray Diffraction under Controlled Oxygen Partial Pressures

The high-temperature phase relationship and thermal expansion coefficient of YBa₂Cu₃O_7-x under constant oxygen nonstoichiometry, x, were determined by high-temperature powder X-ray diffraction analysis under controlled oxygen partial pressure at temperatures up to 800^deg;C. The results are discussed based on reported nonstoichiometry data. The present study showed an orthorhombic-to-tetragonal transition near the composition x = 0.5. The lattice parameter c, perpendicular to the Cu-O plane, showed a maximum at around x = 0.7 to 0.8. In the ortho-rhombic phase, the lattice parameters a and b along the Cu-O plane were essentially constant for x < 0.2. For 0.2 < x < ∼ 0.5, a increased and b decreased with x. In the tetragonal phase, with x < ∼ 0.5, the lattice parameter a decreased with x. The thermal expansion coefficient, α, along the c-axis ranged from 19 × 10^-6 to 25 × 10^-6-K^-1, whereas a along the a- and b-axes ranged from 12 × 10^-6 to 22 × 10^-6-K^-1 at 400° to 800^deg;C, and these values were very small below 400^deg;C. It was found that a, b, and α along the a- and b-axes are smaller when the oxygen content along the respective axes is less, while the area of the ab plane and its thermal expansion coefficient are larger when the deviation of the oxygen content from the stoichiometric compositions of YBa₂Cu₃O₇ or YBa₂Cu₃O₆ is larger. Changes of x and temperature affected c more strongly than a and b.     

Microwave Characteristics of (Pb,Ca)(Fe,Nb,Sn)O3 Dielectric Materials

The dielectric properties of (Pb_{1− x} Ca _x ){(Fe_1/2Nb_1/2)_{1– y} Sn _y }O₃ solid solutions, where 0.4 lessthan equal tox ≤ 0.6, y = 0.05, 0.1, have been investigated at microwave frequencies. The replacement of Fe³⁺/Nb⁵⁺ by Sn⁴⁺ at the B–site of the perov-skite structure considerably improves the loss quality factor Q and does not remarkably affect the dielectric constant epsilon_r and the temperature coefficient of resonant frequency tau_f. The tau_f value of nearly 0 ppm/°C can be realized for x= 0.55. New high-quality dielectric ceramics having epsilon_r of 85.3-89.9,Qf values of 7510-8600 GHz, and τ_f of 0-9 ppm/°C were obtained at 1150°C for 3 h sintering in air. The influence of the sintering atmosphere on dielectric properties was also investigated.     

Sintering, Crystallization, and Properties of B2O3/P2O5-Doped Li2O·Al2O3·4SiO2 Glass-Ceramics

Sintering, crystallization, microstructure, and thermal expansion of Li₂O·Al₂O₃·4SiO₂ glass-ceramics doped with B₂O₃, P₂O₅, or (B₂O₃+ P₂O₅) have been investigated. On heating the glass powder compacts, the glassy phase first crystallized into high-quartz s.s., which transformed into β-spodumene after the crystallization process was essentially complete. The effects of dopants on the crystallization of glass to high-quartz s.s. and the subsequent transformation of high-quartz s.s. to β-spodumene were discussed. The major densification occurred only in the early stage of sintering time due to the rapid crystallization. All dopants were found to promote the densification of the glass powders. The effect of doping on the densification can fairly well be explained by the crystallization tendency. All samples heated to 950°C exhibited a negative coefficient of thermal expansion ranging from about −4.7 × 10^-6 to −0.1 × 10^-6 K^-1. Codoping of B₂O₃ and P₂O₅ resulted in the highest densification and an extremely low coefficient of thermal expansion.