A RF receiver frontend for SC-UWB in a 0.18-μm CMOS process

正A radio frequency(RF) receiver frontend for single-carrier ultra-wideband(SC-UWB) is presented. The front end employs direct-conversion architecture,and consists of a differential low noise amplifier(LNA),a quadrature mixer,and two intermediate frequency(IF) amplifiers.The proposed LNA employs source inductively degenerated topology.First,the expression of input impedance matching bandwidth in terms of gate-source capacitance, resonant frequency and target S_(11) is given.Then,a noise figure optimization strategy under gain and power constraints is proposed,with consideration of the integrated gate inductor,the bond-wire inductance,and its variation.The LNA utilizes two stages with different resonant frequencies to acquire flat gain over the 7.1-8.1 GHz frequency band,and has two gain modes to obtain a higher receiver dynamic range.The mixer uses a double balanced Gilbert structure.The front end is fabricated in a TSMC 0.18-/im RF CMOS process and occupies an area of 1.43 mm~2.In high and low gain modes,the measured maximum conversion gain are 42 dB and 22 dB,input 1 dB compression points are -40 dBm and -20 dBm,and S_(11) is better than -18 dB and -14.5 dB.The 3 dB IF bandwidth is more than 500 MHz.The double sideband noise figure is 4.7 dB in high gain mode.The total power consumption is 65 mW from a 1.8 V supply.     

A 6-7 GHz, 40 dB receiver RF front-end with 4.5 dB minimum noise figure in 0.13μm CMOS for IR-UWB applications

A wideband receiver RP front-end for IR-UWB applications is implemented in 0.13μm CMOS technology. Thanks to the direct sub-sampling architecture,there is no mixing process.Both LNA and VGA work at RF frequencies.To optimize noise as well as linearity,a differential common-source LNA with capacitive cross- coupling is used,which only consumes current of 1.8 mA from a 1.2 V power supply.Following LNA,a two-stage current-steering VGA is adopted for gain tuning.To extend the overall bandwidth,a three-stage staggered peaking technique is used.Measurement results show that the proposed receiver front-end achieves a gain tuning range from 5 to 40 dB within 6-7 GHz,a minimum noise figure of 4.5 dB and a largest IIP₃ of-11 dBm.The core receiver （without test buffer） consumes 14 mW from a 1.2 V power supply and occupies 0.58 mm² area.     

A 0.18μm CMOS low noise amplifier using a current reuse technique for 3.1-10.6 GHz UWB receivers

A new,low complexity,ultra-wideband 3.1-10.6 GHz low noise amplifier(LNA),designed in a chartered 0.18μm RFCMOS technology,is presented.The ultra-wideband LNA consists of only two simple amplifiers with an inter-stage inductor connected.The first stage utilizing a resistive current reuse and dual inductive degeneration technique is used to attain a wideband input matching and low noise figure.A common source amplifier with an inductive peaking technique as the second stage achieves high flat gain and wide -3 dB bandwidth of the overall amplifier simultaneously.The implemented ultra-wideband LNA presents a maximum power gain of 15.6 dB,and a high reverse isolation of—45 dB,and good input/output return losses are better than -10 dB in the frequency range of 3.1-10.6 GHz.An excellent noise figure(NF) of 2.8-4.7 dB was obtained in the required band with a power dissipation of 14.1 mW under a supply voltage of 1.5 V.An input-referred third-order intercept point(IIP3) is -7.1 dBm at 6 GHz.The chip area,including testing pads,is only 0.8×0.9 mm2.     

A 0.18μm CMOS Gilbert low noise mixer with noise cancellation

正This paper presents a broadband Gilbert low noise mixer implemented with noise cancellation technique operating between 10 MHz and 0.9 GHz.The Gilbert mixer is known for its perfect port isolation and bad noise performance.The noise cancellation technique of LNA can be applied here to have a better NF.The chip is implemented in SMIC 0.18μm CMOS technology.Measurement shows that the proposed low noise mixer has a 13.7-19.5 dB voltage gain from 10 MHz to 0.9 GHz,an average noise figure of 5 dB and a minimum value of 4.3 dB.The core area is 0.6 x 0.45 mm~2.     

A 0.18μm CMOS single-inductor single-stage quadrature frontend for GNSS receiver

This paper presents an improved merged architecture for a low-IF GNSS receiver frontend,where the bias current and functions are reused in a stacked quadrature LNA-mixer-VCO.Only a single spiral inductor is implemented for the LC resonator and an extra 1/2 frequency divider is added as the quadrature LO signal generator. The details of the design are presented.The gain plan and noise figure are discussed.The phase noise,quadrature accuracy and power consumption are improved.The test chip is fabricated though a 0.18μm RF CMOS process. The measured noise figure is 5.4 dB on average,with a gain of 43 dB and a IIP3 of-39 dBm.The measured phase noise is better than -105 dBc/Hz at 1 MHz offset.The total power consumption is 19.8 mW with a 1.8 V supply. The experimental results satisfy the requirements for GNSS applications.     

A wideband LNA employing gate-inductive-peaking and noise-canceling techniques in 0.18μm CMOS

正This paper presents a wideband low noise amplifier(LNA) for multi-standard radio applications.The low noise characteristic is achieved by the noise-canceling technique while the bandwidth is enhanced by gateinductive -peaking technique.High-frequency noise performance is consequently improved by the flattened gain over the entire operating frequency band.Fabricated in 0.18μm CMOS process,the LNA achieves 2.5 GHz of -3 dB bandwidth and 16 dB of gain.The gain variation is within±0.8 dB from 300 MHz to 2.2 GHz.The measured noise figure(NF) and average HP3 are 3.4 dB and -2 dBm,respectively.The proposed LNA occupies 0.39 mm2 core chip area.Operating at 1.8 V,the LNA drains a current of 11.7 mA.     

Design of a 0.18μm CMOS multi-band compatible low power GNSS receiver RF frontend

This paper presents the design and implementation of a fully integrated multi-band RF receiver frontend for GNSS applications on L-band.A single RF signal channel with a low-IF architecture is adopted for multi-band operation on the RF section,which mainly consists of a low noise amplifier(LNA),a down-converter,polyphase filters and summing circuits.An improved cascode source degenerated LNA with a multi-band shared off-chip matching network and band switches is implemented in the first amplifying stage....     

A wideband current-commutating passive mixer for multi-standard receivers in a 0.18 μm CMOS

This paper reports a wideband passive mixer for direct conversion multi-standard receivers.A brief comparison between current-commutating passive mixers and active mixers is presented.The effect of source and load impedance on the linearity of a mixer is analyzed.Specially,the impact of the input impedance of the transimpedance amplifier(TIA),which acts as the load impedance of a mixer,is investigated in detail.The analysis is verified by a passive mixer implemented with 0.18 m CMOS technology.The circuit is inductorless and can operate over a broad frequency range.On wafer measurements show that,with radio frequency(RF) ranges from 700 MHz to 2.3 GHz,the mixer achieves 21 dB of conversion voltage gain with a-1 dB intermediate frequency(IF) bandwidth of 10 MHz.The measured IIP3 is 9 dBm and the measured double-sideband noise figure(NF) is 10.6 dB at 10 MHz output.The chip occupies an area of 0.19 mm2 and drains a current of 5.5 mA from a 1.8 V supply.     

An ultra-broadband distributed passive gate-pumped mixer in 0.18μm CMOS

A broadband distributed passive gate-pumped mixer(DPGM) using standard 0.18μm CMOS technology is presented.By employing distributed topology,the mixer can operate at a wide frequency range.In addition,a fourth-order low pass filter is applied to improve the port-to-port isolation.This paper also analyzes the impedance match and conversion loss of the mixer,which consumes zero dc power and exhibits a measured conversion loss of 9.4—17 dB from 3 to 40 GHz with a compact size of 0.78 mm~2.The input referred 1 dB compression point is higher than 4 dBm at a fixed IF frequency of 500 MHz and RF frequency of 23 GHz,and the measured RF-to-LO, RF-to-IF and LO-to-IF isolations are better than 21,38 and 45 dB,respectively.The mixer is suitable for WLAN, UWB,Wi-Max,automotive radar systems and other millimeter-wave radio applications.     

A fully integrated direct-conversion digital satellite tuner in 0.18μm CMOS

A fully integrated direct-conversion digital satellite tuner for DVB-S/S2 and ABS-S applications is presented.A broadband noise-canceling Balun-LNA and passive quadrature mixers provided a high-linearity low noise RF front-end,while the synthesizer integrated the loop filter to reduce the solution cost and system debug time.Fabricated in 0.18μm CMOS,the chip achieves a less than 7.6 dB noise figure over a 900-2150 MHz L-band, while the measured sensitivity for 4.42 MS/s QPSK-3/4 mode is -91 dBm at the PCB connector.The fully integrated integer-N synthesizer operating from 2150 to 4350 MHz achieves less than 1℃integrated phase error. The chip consumes about 145 mA at a 3.3 V supply with internal integrated LDOs.     

LC voltage controlled oscillator in 0.18-μm RF CMOS

An integrated low-phase-noise voltage-controlled oscillator(VCO) has been designed and fabricated in SMIC 0.18μm RF CMOS technology.The circuit employs an optimally designed LC resonator and a differential cross-coupling amplifier acts as a negative resistor to compensate the energy loss of the resonator.To extend the frequency tuning range,a three-bit binary-weighted switched capacitor array is used in the circuit.The testing result indicates that the VCO achieves a tuning range of 60%from 1.92 to 3.35 GHz.The phase noise of the VCO is -117.8 dBc/Hz at 1 MHz offset from the carrier frequency of 2.4 GHz.It draws 5.6 mA current from a 1.8 V supply.The VCO integrated circuit occupies a die area of 600×900μm~2.It can be used in the IEEE802.11 b based wireless local network receiver.     

A reconfigurable passive mixer for multimode multistandard receivers in 0.18 μm CMOS

This paper presents a reconfigurable quadrature passive mixer for multimode multistandard receivers. By using controllable transconductor and transimpedance-amplifier stages, the voltage conversion gain of the mixer is reconfigured according to the requirement of the selected communication standard Other characteristics such as noises figure, linearity and power consumption are also reconfigured consequently. The design concept is verified by implementing a quadrature passive mixer in 0.18 μm CMOS technology. On wafer measurement results show that, with the input radio frequency ranges from 700 MHz to 2.3 GHz, the mixer achieves a controllable voltage conversion gain from 4 to 22 dB with a step size of 6 dB. The measured maximum ⅡP3 is 8.5 dBm and the minimum noise figure is 8.0 dB. The consumed current for a single branch (I or Q) ranges from 3.1 to 5.6 mA from a 1.8 V supply voltage. The chip occupies an area of 0.71 mm² including pads.     

A 1.2-V, 84-dB Σ△ ADM in 0.18-μm digital CMOS technology

A low power and low voltage∑△analog-to-digital modulator is realized with digital CMOS technology, which is due to full compensated depletion mode capacitors.Compared with mixed signal technology,this type of modulator is more compatible for pure digital applications.A pseudo-two-stage class-AB OTA is used in switchedcapacitor integrators for low voltage and low power.The modulator is realized in standard SMIC 0.18μm 1P6M digital CMOS technology.Measured results show that with 1.2 V supply voltage and a 6 MHz sample clock,the dynamic range of the modulator is 84 dB and the total power dissipation is 2460μW.     

A 50 MHz-1 GHz high linearity CATV amplifier with a 0.15μm InGaAs PHEMT process

A 50 MHz-1 GHz low noise and high linearity amplifier monolithic-microwave integrated-circuit (MMIC) for cable TV is presented.A shunt AC voltage negative feedback combined with source current negative feedback is adopted to extend the bandwidth and linearity.A novel DC bias feedback is introduced to stabilize the operation point,which improved the linearity further.The circuit was fabricated with a 0.15μm InGaAs PHEMT (pseudomorphic high electron mobility transistor) process.The test was carried out in 75Ωsystems from 50 MHz to 1 GHz.The measurement results showed that it gave a small signal gain of 16.5 dB with little gain ripples of less than±1dB.An excellent noise figure of 1.7-2.9 dB is obtained in the designed band.The IIP3 is 16 dBm, which shows very good linearity.The CSO and CTB are high up to 68 dBc and 77 dBc,respectively.The chip area is 0.56 mm~2 and the power dissipation is 110 mA with a 5 V supply.It is ideally suited to cable TV systems.     

A 12-Channel,30Gb/s,0.18μm CMOS Front-End Amplifier for Parallel Optic-Fiber Receivers

给出了一个采用TSMC 0.18μm CMOS工艺设计并实现的12路30Gb/s并行光接收前端放大器.电路设计采用RGC结构和噪声优化技术,克服了CMOS光检测器大寄生电容造成的带宽不够的问题.测试结果表明,在2pF的寄生电容下单信道传输速率达到了2.5Gb/s,在0.8mVpp输入下得到了清晰的眼图.提出了一种同时采用p 保护环(PGR)、n 保护环(NGR)和深n阱(DNW)的并行放大器隔离结构,有效地抑制了并行放大器之间的串扰,减小了放大器之间的衬底耦合噪声.测量结果表明,这种结构与PGR和PGR NGR相比,在1GHz时放大器之间的隔离度分别提高了29.2和8.1dB,在2GHz时放大器之间的隔离度分别提高了8.1和2.5dB.芯片采用1.8V电源供电,单路前端放大器的功耗为85mW,12路总功耗约为1W.     

A Systematical Approach for Noise in CMOS LNA

A systematic approach is used to analyze the noise in CMOS low noise amplifier(LNA),including channel noise and induced gate noise in MOS devices.A new analytical formula for noise figure is proposed.Based on this formula,the impacts of distributed gate resistance and intrinsic channel resistance on noise performance are discussed.Two kinds of noise optimization approaches are performed and applied to the design of a 5.2GHz CMOS LNA.     

A 5-GHz programmable frequency divider in 0.18-μm CMOS technology

正A 5-GHz CMOS programmable frequency divider whose modulus can be varied from 2403 to 2480 for 2.4-GHz ZigBee applications is presented.The divider based on a dual-modulus prescaler(DMP) and pulse-swallow counter is designed to reduce power consumption and chip area.Implemented in the 0.18-μm mixed-signal CMOS process,the divider operates over a wide range of 1-7.4 GHz with an input signal of 7.5 dBm;the programmable divider output phase noise is -125.3 dBc/Hz at an offset of 100 kHz.The core circuit without test buffer consumes 4.3 mA current from a 1.8 V power supply and occupies a chip area of approximately 0.015 mm~2.The experimental results indicate that the programmable divider works well for its application in frequency synthesizers.