Surface properties and reactivity of Cu/γ-Al2O3 catalysts for NO reduction by C3H6: Influences of calcination temperatures and additives

The influences of calcination temperatures and additives for 10 wt.% Cu/γ-Al₂O₃ catalysts on the surface properties and reactivity for NO reduction by C₃H₆ in the presence of excess oxygen were investigated. The results of XRD and XPS show that the 10 wt.% Cu/γ-Al₂O₃ catalysts calcined below 973 K possess highly dispersed surface and bulk CuO phases. The 10 wt.% Cu/γ-Al₂O₃ and 10 wt.% Mn–10 wt.% Cu/γ-Al₂O₃ catalysts calcined at 1073 K possess a CuAl₂O₄ phase with a spinel-type structure. In addition, the 10 wt.% La–10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K possesses a bulk CuO phase. The result of NO reduction by C₃H₆ shows that the CuAl₂O₄ is a more active phase than the highly dispersed and bulk CuO phase. However, the 10 wt.% Mn–10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K possesses significantly lower reactivity for NO reduction than the 10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K, although these catalysts possess the same CuAl₂O₄ phase. The low reactivity for NO reduction for 10 wt.% Mn–10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K is attributed to the formation of less active CuAl₂O₄ phase with high aggregation and preferential promotion of C₃H₆ combustion to CO_x by MnO₂. The engine dynamometer test for NO reduction shows that the C₃H₆ is a more effective reducing agent for NO reduction than the C₂H₅OH. The maximum reactivity for NO reduction by C₃H₆ is reached when the NO/C₃H₆ ratio is one.     

Oxidative transformation of methane over nickel catalysts supported on rare-earth metal oxides

The oxidative transformation of methane over Ni catalysts supported on La, Sm and Ce oxides was investigated at atmospheric pressure, T=723–923 K and CH₄/O₂=1–10. The BET surface areas were low (3–22 m² g⁻¹) and decreased strongly after reaction (down to 0.5  m² g⁻¹). Carbonate species, Ni₂O₃ and supported oxides were identified by XRD or IR spectroscopy studies in both the fresh and used catalysts. The Ni° phase was also probably formed as amorphous phase. The oxidative coupling of methane route passed through a minimum as a function of the Ni percentage and was favored by the Ce or Sm oxide support, Li additive and low reaction temperature. High selectivities (60–90%) and good yields (about 15%) in C₂ hydrocarbons with low carbon balance (0–10%) were obtained at 823 K. La supported oxide, Ba additive and high reaction temperature favored the partial oxidation of methane. The obtained results were discussed in the light of the reducibility and acid–base properties of the catalysts.     

A comparative study of coprecipitated BaCO3/La2On(CO3)rn catalysts for the oxidative coupling of methane

Coprecipitated catalyst systems containing BaCO₃ and La₂O_n(CO₃)_m (n≥1.5) with La/Ba = 0.05-10 were tested for catalytic activity, selectivity and stability in the oxidative coupling of methane reaction (OCM). Maximum C₂⁺ selectivities of 78% and C₂⁺ yields of 11% were obtained. The results show that La is the more active cation component of the system. The presence of BaCO₃ in the system leads to decreasing crystal size of the La phases, and to higher C₂⁺ selectivities at equal methane conversions. Life time tests showed that the Ba- La-containing catalysts were quite stable. Na impurities in the system lead to larger crystals in the La phases, and to less selective and less stable catalysts for the OCM reaction. Na is lost during reaction.     

Novel utilization of mesoporous molecular sieves as supports of cobalt catalysts in Fischer–Tropsch synthesis

Mesoporous molecular sieves (MCM-41 and SBA-15) with different pore diameters have been studied as supports of high loading of Co catalysts, and the performances in FT synthesis have been examined with a fixed bed stainless steel reactor at 2.0 MPa for the purpose of efficient production of C₁₀–C₂₀ fraction as the main component of diesel fuel. The method of exchanging template ions in uncalcined MCM-41 with Co²⁺ ions is effective for holding 10–20% Co within the mesopores while keeping the structure regularity of MCM-41 to some extent, compared with the conventional impregnation method using calcined MCM-41. At 523 K, CO conversion and selectivity to C₁₀–C₂₀ hydrocarbons are both higher at larger loading of 20% Co for the exchanged catalysts with pore diameters of 2.7–2.9 nm. When four kinds of 20% Co/SBA-15 with the diameters of 3.5–13 nm, prepared by the impregnation method using an ethanol solution of Co acetate, are used in FT synthesis at 523 K, the catalyst with the diameter of 8.3 nm shows the largest CO conversion, which is higher than those over MCM-41 supported Co catalysts. At a lower temperature of 503 K, however, the acetate-derived Co is almost inactive. In contrast, the use of Co nitrate alone or an equimolar mixture of the acetate and nitrate as Co precursor drastically enhances the reaction rate and consequently provides high space–time yield (260–270 g C/kg_cat h) of C₁₀–C₂₀ hydrocarbons. The X-ray diffraction and temperature-programmed reduction measurements show that the dependency of the catalytic performance of 20% Co/SBA-15 on its precursor originates probably from the differences in not only the reducibility of the calcined catalyst but also the dispersion of metallic Co. Catalyst characterization after FT synthesis strongly suggests the high stability of the most effective Co/SBA-15 in the dispersion and reducibility of the oxide species and in the mesoporous structure.     

Direct synthesis of organic carbonates from the reaction of CO2 with methanol and ethanol over CeO2 catalysts

The catalytic properties of CeO₂ catalysts in direct synthesis of dimethyl carbonate (DMC) from CH₃OH and CO₂ were investigated. The formation rate of DMC over the catalysts calcined at 873 K and above was almost proportional to the surface area of catalysts. However, CeO₂ calcined at 673 K showed lower activity than expected from the surface area. From the results of catalyst characterization, CeO₂ calcined at 673 K contained considerable amount of amorphous phase. In contrast, the ratio of amorphous phase decreased on the catalysts calcined at 873 K and above. This suggests that stable crystallite surface is active for the reaction.

In the CH₃OH + C₂H₅OH + CO₂ reaction at low temperature, ethyl methyl carbonate (EMC) was formed, and selectivity of EMC formation was comparable to that of DMC. The formation route is discussed by the comparison with transesterification reaction.     

Methane oxidative coupling on BaF2/LaOF catalyst

The oxidative coupling of methane (OCM) was studied on BaF₂/LaOF and good catalytic results were obtained. Under the conditions of GHSV = 15 000 h⁻¹ and a reaction temperature of 1043 K, a C₂ yield of 20.66% with a CH₄ conversion of 33.08% and a C₂ selectivity of 62.47% was achieved at CH₄:O₂ = 3:1, and high C₂ selectivities of 81.20% and 84.55% with a CH₄ conversion of 19.53% and 16.54% were obtained at CH₄:O₂ ratios of 6:1 and 9:1, respectively. X-ray diffraction results showed that only tetragonal LaOF existed in the BaF₂/LaOF catalysts with BaF₂ content below 18 mol-%, but a contracted BaF₂ phase was also observed at higher BaF₂ content (above 18 mol-%).     

Selective catalytic reduction of NO by C3H8 over CoOx/Al2O3: An investigation of structure–activity relationships

A series of CoO_x/Al₂O₃ catalysts was prepared, characterized, and applied for the selective catalytic reduction (SCR) of NO by C₃H₈. The results of XRD, UV–vis, IR, Far-IR and ESR characterizations of the catalysts suggest that the predominant oxidation state of cobalt species is +2 for the catalysts with low cobalt loading (≤2 mol%) and for the catalysts with 4 mol% cobalt loading prepared by sol–gel and co-precipitation. Co₃O₄ crystallites or agglomerates are the predominant species in the catalysts with high cobalt loading prepared by incipient wetness impregnation and solid dispersion. An optimized CoO_x/Al₂O₃ catalyst shows high activity in SCR of NO by C₃H₈ (100% conversion of NO at 723 K, GHSV: 10,000 h⁻¹). The activity of the selective catalytic reduction of NO by C₃H₈ increases with the increase of cobalt–alumina interactions in the catalysts. The influences of cobalt loading and catalyst preparation method on the catalytic performance suggest that tiny CoAl₂O₄ crystallites highly dispersed on alumina are responsible for the efficient catalytic reduction of NO, whereas Co₃O₄ crystallites catalyze the combustion of C₃H₈ only.     

In situ IR and pulse reaction studies on the active oxygen species over SrF2/Nd2O3 catalyst for oxidative coupling of methane

Pulse reaction method and in situ IR spectroscopy were used to characterize the active oxygen species for oxidative coupling of methane (OCM) over SrF₂/Nd₂O₃ catalyst. It was found that OCM activity of the catalyst was very low in the absence of gas phase oxygen, which indicated that lattice oxygen species contributed little to the yield of C₂ hydrocarbons. IR band of superoxide species (O₂⁻) was detected on the O₂-preadsorbed SrF₂/Nd₂O₃. The substitution of ¹⁸O₂ isotope for ¹⁶O₂ caused the IR band of O₂⁻ at 1128 cm⁻¹ to shift to lower wavenumbers (1094 and 1062 cm⁻¹), consistent with the assignment of the spectra to the O₂⁻ species. A good correlation between the rate of disappearance of surface O₂⁻ and the rate of formation of gas phase C₂H₄ was observed upon interaction of CH₄ with O₂-preadsorbed catalyst at 700 °C. The O₂⁻ species was also observed on the catalyst under working condition. These results suggest that O₂⁻ species is the active oxygen species for OCM reaction on SrF₂/Nd₂O₃ catalyst.     

The selective oxidation of methane to ethane and ethylene in a solid oxide electrolyte reactor

A study of the selective oxidative coupling of methane (OCM) to C₂ hydrocarbons (ethane and ethylene) in a solid-state electrochemical reactor made from yttria-stabilized zirconia (YSZ) has been made. Three different catalyst–electrode systems based on silver and two trimetallic formulations of Mn modified alkali (Na and K) tungstates supported on silica were used. A comparison is made between co-fed and electrochemically-supplied oxygen. The electrochemically-supplied oxygen gave higher overall C₂ selectivities than the co-fed method under low current conditions, which was attributed to differences in local methane to oxygen ratios at the catalyst surface. The potassium tungstate supported catalyst gave the best overall C₂ selectivity (86% at 4% C₂ yield).     

The oxidative coupling of methane and the oxidative dehydrogenation of ethane over a niobium promoted lithium doped magnesium oxide catalyst

The promoting effect of niobium in a Li/MgO catalyst for the oxidative coupling of methane (OCM) and for the oxidative dehydrogenation of ethane (ODHE) has been studied in some detail. It has been found that a Li/Nb/MgO catalyst with 16 wt % niobium showed the highest activity for the C₂ production in the OCM reaction; the activity at 600 °C was ten times that of the Li/MgO catalyst at the same temperature. The Li/Nb/MgO catalyst was also slightly more active for the ODHE reaction than was the Li/MgO catalyst. However, the Li/Nb/MgO catalyst produced considerably more carbon dioxide in the both reactions. Structural investigation of the catalyst showed that the addition of niobium to the Li/MgO catalyst increased the surface area and gave an increase in the lithium content of the calcined catalysts. Two niobium phases, LiNbO₃ and Li₃NbO₄, were formed; it is shown that the first of these probably causes the increased activity. Ageing experiments showed that the activity of the catalyst was lost if the catalyst was used above 720 °C, the melting point of the lithium carbonate phase. The catalyst showed a decrease of surface area after ageing and a sharp decrease of the amount of the two niobium phases. The addition of carbon dioxide to the feed could not prevent the deactivation of the Li/Nb/MgO catalyst.     

Selective catalytic reduction of NO by C2H2 over MoO3/HZSM-5

Molybdenum impregnated HZSM-5 zeolite catalysts with MoO₃ loading from 1 to 8 wt.% were studied in detail for the selective catalytic reduction (C₂H₂-SCR) of NO by acetylene. A 83.9% of NO could be removed by the reductant at 350 °C under 1600 ppm of NO, 800 ppm of C₂H₂ and 9.95% of O₂ in He over 2%MoO₃/HZSM-5 catalyst with a specific activity of in NO elimination and the competitiveness factor (c.f.) of 33.6% for the reductant. The NO elimination level and the c.f. value were ca. 3–4 times as high as those using methane or propene as reductant over the catalyst in the same reaction condition. About same reaction rate was estimated in NO oxidation as that in the NO reduction over each xMoO₃/HZSM-5 (x = 0–8%) catalyst, which confirms that NO₂ is a crucial intermediate for the aimed reaction over the catalysts. Appropriate amount of Mo incorporation to HZSM-5 considerably enhanced the title reaction, both by accelerating the intermediate formation and by strengthening the adsorption NO_x on the catalyst surface under the reaction conditions. Rather lower adsorption tendency of acetylene compared with propene on the catalysts explains the catalyst's steady performance in the C₂H₂-SCR of NO and rapid deactivation in the C₃H₆-SCR of NO.     

n-Pentane isomerization over promoted SZ/MCM-41 catalysts

With metal sulfate as the precursor, the catalysts of sulfated zirconia on MCM-41, Al- and Ga-promoted sulfated zirconia on MCM-41 (named as SZ/MCM-41, ASZ/MCM-41 and GSZ/MCM-41, respectively) were prepared by direct dispersion in the as-synthesized MCM-41 materials, followed by thermal decomposition. The catalysts were characterized with various techniques such as XRD, FTIR, N₂ adsorption, NH₃-TPD, DRIFT, and TPR-MS. The ordered porous structure was still maintained in the catalysts. The addition of promoters helps to retard the phase transformation of ZrO₂ from tetragonal phase to monoclinic phase. Isomerization of n-pentane was investigated over the catalysts. In comparison to SZ/MCM-41, both promoted catalysts showed much improved catalytic activity and selectivity for isomerization of n-pentane. Moreover, the catalytical activities of both promoted catalysts for pentane isomerization remained steady over the period of 180 min while the activities of the unpromoted catalyst decreased in <120 min. Characterization of acidity showed no significant difference in strength distributions of the acid sites over the catalysts. The nature of acid sites in SZ/MCM-41 was affected by the presence of aluminum, but not affected by the presence of gallium. On the other hand, TPR study shows sulfur on GSZ/MCM-41 is much easier to reduce than SZ/MCM-41 and ASZ/MCM-41. The presence of gallium improved the redox capability provided by the sulfate ions in GSZ/MCM-41 catalyst. The causes for the promotion effects of Ga and Al are discussed.     

Electron spectroscopy of sulfated zirconia, its activity in n-hexane conversion and possible reasons of its deactivation

Sulfated zirconia catalysts were prepared and characterized by X-ray photoelectron spectroscopy taken in the dried state (fresh) and after calcination at 900 K (calc.). A maximum activity was observed as a function of the calcination temperature. The Zr 3d region showed that any Zr hydroxide in the dried catalyst transformed into zirconium oxide upon calcination. The O 1s peak could be fitted by two components corresponding to ZrO₂ and sulfate, respectively. Sulfur was present as sulfate. Both catalysts showed activity in n-hexane conversion (including isomerization) between 300 and 473 K. The activity of the calcined catalyst was much higher. The main products were isopentane and isobutane, along with 2-methyl- and 3-methylpentane. The activity was not stable and only a limited amount of n-hexane transformed before final deactivation. This observation pointed to a limited amount of active sites able to start the reaction. The activity could be fully regenerated by oxygen treatment. Thus, the “oxidative” start of the reaction [ A. Ghenciu, D. Farcasiu, Catal. Lett. 44 (1997) 29] may have also played a role apart from those on strong acid sites. Deactivation may have been due to a partial reduction of sulfate groups rather than to carbon accumulation, as shown also by the minor amounts of S⁴⁺ detected by XPS. Parallel isomerization and splitting of hexane into two C₃ units may occur, followed by the formation of surface C₉ units, the latter being intermediate of larger fragments.     

Oligomerization pathways of dichlorodifluoromethane hydrodechlorination catalyzed by activated carbon supported Pt-Cu, Pt-Ag, Pt-Fe, and Pt-Co

Activated carbon-supported Pt-Cu, Pt-Ag, Pt-Co, Pt-Fe, and Pt catalyze the formation of oligomerization products from CF₂Cl₂ and H₂ mixture (1:1 ratio) at 523 K. All catalysts deactivate with time on stream. The Pt-Co/C catalyst exhibits the highest selectivity toward C₂–C₃ hydrocarbons (50%), whereas Pt-Cu/C is the most selective toward tetrafluoroethylene (20%). The other catalysts (Pt, Pt-Ag, Pt-Fe) exhibit negligible oligomerization activity, CH₄ and partially halogenated C₁ molecules are the main products. The performance of each catalyst is understood in terms of the difference in the stability of bimetallic particles toward segregation under dechlorination conditions.     

NO reduction by CH4 in the presence of excess O2 over Mn/sulfated zirconia catalysts

Selective catalytic reduction (SCR) of NO with methane in the presence of excess oxygen has been investigated over a series of Mn-loaded sulfated zirconia (SZ) catalysts. It was found that the Mn/SZ with a metal loading of 2–3 wt.% exhibited high activity for the NO reduction, and the maximum NO conversion over the Mn/SZ catalyst was higher than that over Mn/HZSM-5. NH₃–TPD results of the catalysts showed that the sulfation process of the supports resulted in the generation of strong acid sites, which is essential for the SCR of NO with methane. On the other hand, the N₂ adsorption and the H₂–TPR of the catalysts demonstrated that the presence of the SO₄²⁻ species promoted the dispersion of the metal species and made the Mn species less reducible. Such an increased dispersion of metal species suppressed the combustion reaction of CH₄ by O₂ and increased the selectivity towards NO. The Mn/SZ catalysts prepared by different methods exhibited similar activities in the SCR of NO with methane, indicating the importance of SO₄²⁻. The most attractive feature of the Mn/SZ catalysts was that they were more tolerant to water and SO₂ poisoning than Mn/HZSM-5 catalysts and exhibited higher reversibility after removal of SO₂.     

Non-oxidative reaction of CBrF3 with methane over NiZSM-5 and HZSM-5

Catalytic hydrodehalogenation of CBrF₃ with methane was studied over NiZSM-5 and HZSM-5 in tubular reactor between 573 and 873 K and at ambient pressure. It was found that the incorporation of nickel into HZSM-5 significantly enhanced the activity of the zeolite. A variety of products were formed during reaction, including CH₃Br, CHF₃, CH₂Br₂, C₂F₆, C₂H₄, C₂H₂, C₂H₂F₂, CHBrF₂, CH₂BrF, and C₂H₃Br. XRD analysis showed that these two zeolite catalysts did not suffer any loss in their crystallinity during use. Deactivation of both NiZSM-5 and HZSM-5 may, in part, be due to poisoning of the zeolite by halogens. Coking is another cause of the deactivation of HZSM-5, but appears to play a minor role in NiZSM-5 deactivation. A series of methylated silicone oils was detected during reaction over NiZSM-5.     

载体对Li-Mn氧化物催化甲烷氧化偶联反应作用

采用浸渍法制备不同金属氧化物载体负载的Li-Mn/MO_x(M=Mg,La,Ti,Si,Zr,Ta)催化剂,对其甲烷氧化偶联反应活性进行评价。结果表明,以TiO_2为载体制备的Li-Mn/TiO_2催化剂具有较高的CH_4转化率和C2烃选择性,C_2烃产率显著提高,金属氧化物TiO_2是Li-Mn复合氧化物的优良催化剂载体。n(Li)∶n(Mn)=1.0∶2.0形成的Li-Mn/TiO_2催化剂具有最高的CH_4转化率和C_2烃选择性,n(C_2H_4)∶n(C_2H_6)的增加有助于提高反应产物中C_2H_4的相对浓度,W元素的添加未能进一步提高Li-Mn/TiO_2催化剂的催化活性。Li-Mn/TiO_2催化剂在n(Li)∶n(Mn)=1.0∶2.0、反应温度775℃、反应压力0.1 MPa、V(CH_4)∶V(O_2)=2.5、空速7 200 m L·(h·g)~(-1)和催化剂用量0.5 g条件下,CH_4转化率达31.9%,C_2选择性达52.7%,表现出最佳催化效果。     

Fischer–Tropsch synthesis over Re-promoted Co supported on Al2O3, SiO2 and TiO2: Effect of water

The activity and selectivity of rhenium promoted cobalt Fischer–Tropsch catalysts supported on Al₂O₃, TiO₂ and SiO₂ have been studied in a fixed-bed reactor at 483 K and 20 bar. Exposure of the catalysts to water added to the feed deactivates the Al₂O₃ supported catalyst, while the activity of the TiO₂ and SiO₂ supported catalysts increased. However, at high concentrations of water both the SiO₂ and TiO₂ supported catalyst deactivated. Common for all catalysts was an increase in C₅₊ selectivity and a decrease in the CH₄ selectivity by increasing the water partial pressure. The catalysts have been characterized by scanning transmission electron microscope (STEM), BET, H₂ chemisorption and X-ray diffraction (XRD).     

Total oxidation of propene and propane over gold–copper oxide on alumina catalysts: Comparison with Pt/Al2O3

Oxidation of propene and propane to CO₂ and H₂O has been studied over Au/Al₂O₃ and two different Au/CuO/Al₂O₃ (4 wt.% Au and 7.4 wt.% Au) catalysts and compared with the catalytic behaviour of Au/Co₃O₄/Al₂O₃ (4.1 wt.% Au) and Pt/Al₂O₃ (4.8 wt.% Pt) catalysts. The various characterization techniques employed (XRD, HRTEM, TPR and DR-UV–vis) revealed the presence of metallic gold, along with a highly dispersed CuO (6 wt.% CuO), or more crystalline CuO phase (12 wt.% CuO).

A higher CuO loading does not significantly influence the catalytic performance of the catalyst in propene oxidation, the gold loading appears to be more important. Moreover, it was found that 7.4Au/CuO/Al₂O₃ is almost as active as Pt/Al₂O₃, whereas Au/Co₃O₄/Al₂O₃ performs less than any of the CuO-containing gold-based catalysts.

The light-off temperature for C₃H₈ oxidation is significantly higher than for C₃H₆. For this reaction the particle size effect appears to prevail over the effect of gold loading. The most active catalysts are 4Au/CuO/Al₂O₃ (gold particles less than 3 nm) and 4Au/Co₃O₄/Al₂O₃ (gold particles less than 5 nm).     

Catalytic reduction of SO2 over supported transition-metal oxide catalysts with C2H4 as a reducing agent

This work investigates performances of supported transition-metal oxide catalysts for the catalytic reduction of SO₂ with C₂H₄ as a reducing agent. Experimental results indicate that the active species, the support, the feed ratio of C₂H₄/SO₂, and pretreatment are all important factors affecting catalyst activity. Fe₂O₃/γ-Al₂O₃ was found to be the most active catalyst among six γ-Al₂O₃-supported metal oxide catalysts tested. With Fe₂O₃ as the active species, of the supports tested, CeO₂ is the most suitable one. Using this Fe₂O₃/CeO₂ catalyst, we found that the optimal Fe content is 10 wt.%, the optimal feed ratio of C₂H₄/SO₂ is 1:1, and the catalyst presulfidized by H₂+H₂S exhibits a higher performance than those pretreated with H₂ or He. Although the feed concentrations of C₂H₄:SO₂ being 3000:3000 ppm provide a higher conversion of SO₂, the sulfur yield decreases drastically at temperatures above 300 °C. With higher feed concentrations, maximum yield appears at higher temperatures. The C₂H₄ temperature-programmed desorption (C₂H₄-TPD) and SO₂-TPD desorption patterns illustrate that Fe₂O₃/CeO₂ can adsorb and desorb C₂H₄ and SO₂ more easily than can Fe₂O₃/γ-Al₂O₃. Moreover, the SO₂-TPD patterns further show that Fe₂O₃/γ-Al₂O₃ is more seriously inhibited by SO₂. These findings may properly explain why Fe₂O₃/CeO₂ has a higher activity for the reduction of SO₂.