共查询到18条相似文献,搜索用时 109 毫秒
1.
2.
在研制的双源离子注入机上,把钛离子和氮离子同时注入工业铝、45#钢、CCr12钢、GCr15钢。摩擦学实验表明,上面四种材料经钛离子和氮离子同时注入后,动态 有不同程度的降低。AES和XRD分析表明经钛、氮双离子同时注入时,工业铝表层生成了Ti、Ti3Al,Ti3Al,TiAl,AlN,铁基样品表面层生成了TiN,FeTi,Fe2N,Fe3N,ε-Fe2-3,r-Fe4n等金属化合物或硬质合金相。 相似文献
3.
4.
5.
应用余氏理论,对不同Al含量的富Fe区Fe-Al无序固溶体进行价电子结构计算和分析,从理论上探讨了Al含量对合金晶格常数,原子磁矩,塑性以及晶内原子状态的,研究发现,Fe-Al无序固溶体的晶格常数,原子磁矩和塑性随含Al量的变化,是由于合金中Fe,Al原子之间相互作用导致原子状态发生变化的结果。 相似文献
6.
Al含量对Fe—Al无序固溶体性能的影响 总被引:2,自引:0,他引:2
本文应用余氏理论,对不同Al含量的富Fe区Fe-Al无序固溶体进行价电子结构计算和分析,从理论上探讨了Al含量合金晶格常数、原子磁矩、塑性以及晶体内原子状态的影响。研究发现,Fe-Al无序固溶体的晶格常数、原子磁矩和塑性随含Al的变化,是由于合金中Fe,Al原子之间相互作用导致原子状态发生变化的结果。 相似文献
7.
8.
9.
10.
11.
FeTi系贮氢合金是一类重要的贮氢材料,作为贮氢介质具有贮氢量大、价格便宜等优点,但活化性能和抗中毒性能较差。本文详细综述了FeTi系贮氢合金的氢化性能、活化机理以及改性处理等方面的内容。 相似文献
12.
TiC与TiC-WC的添加对FeAl/Al2O3复合材料力学性能的影响 总被引:2,自引:0,他引:2
在FeAl/Al2O3复合材料基体中分别加入TiC或TiC-WC固溶体可显著提高其抗弯强度。当添加20%TiC和20%TiC-WC固溶体时,复合材料的抗弯强度分别达到1028.46MPa和1328.72MPa,但其断裂韧性分别降低约40%和30%。当TiC-WC固溶体加入量为5%时,可同时提高复合材料的抗弯强度和断裂韧性。 相似文献
13.
采用合金化的方法向富钛储氢合金FeTi1.2中添加少量LaNi5以形成四元系合金FeTi1.2 xwt%LaNi5来改善FeTi1.2合金的储氢性能,虽然XRD没有检出合金中有LaNi5相的存在,但是FeTi1.2合金的储氢性能特别是活化性能得到了改善,FeTi1.2 xwt%LaNi5合金还具有较高的储氢量,293K吸氢的FeTi1.2 2wt%LaNi5合金在333K时的放氢量为186.4ml/g,明显超过FeTi1.2合金的172.3ml/g。 相似文献
14.
15.
长程有序金属间化合物FeAl合金的研究现状与发展 总被引:2,自引:0,他引:2
近年来,金属间化合物FeAl由于具有一系列优点而受到普遍重视,大力开展研究。本文综述国外在FeAl方面发表的大量文献和作者近二年的研究工作。主要内容包括相结构和晶体缺陷,物理性能和抗腐蚀性能,以及脆性、显微组织和力学性能等方面。 相似文献
16.
Surface studies by means of AES and XPS show that during the activation process of FeTi surface segregation occurs. In a surface layer Ti diffuses to the surface and metallic Fe clusters are formed. They catalyze the hydrogen absorption and are the reason for the irreversible change of the magnetic properties of FeTi upon hydrogenation. At room temperature the surface segregation is not effective enough to restore the catalytic active surface so that FeTi is deactivated easily in air. 相似文献
17.
Masahiro Kitada 《Journal of Materials Science》1981,16(9):2527-2530
Hydrogen absorption and desorption characteristics of commercially supplied ferrotitaniums with 41 to 51 at% Ti have been studied. The characteristics are similar to those of high purity FeTi although the ferro-titaniums include some impurities. The activation temperatures of the ferro-titaniums are slightly higher than that of the high purity FeTi. Plateaus in the hydrogen absorption and desorption curves are not obvious compared with those of high purity FeTi. It is concluded that the ferro-titaniums are good, low-cost hydrogen storage materials. 相似文献
18.
Hydrogen absorption by nanocrystalline and amorphous Fe-Ti with palladium catalyst,produced by ball milling 总被引:1,自引:0,他引:1
L. Zaluski A. Zaluska P. Tessier J. O. Ström-Olsen R. Schulz 《Journal of Materials Science》1996,31(3):695-698
The effects of microstructure on hydrogen absorption in FeTi are reported. Powders of FeTi with different microstructures (nanocrystalline and amorphous) were prepared by high-energy ball-milling. FeTi powders were also modified with small amounts (less than 1 wt%) of palladium catalyst to eliminate activation. Enhancements in hydrogen absorption for both nanocrystalline and amorphous FeTi powders were observed. 相似文献