Insight into high areal capacitances of low apparent surface area carbons derived from nitrogen-rich polymers

The energy storage mechanism of N-doped carbons with low apparent specific surface areas (Brunauer–Emmett–Teller specific surface area determined by N₂ adsorption) has puzzled the researchers in the supercapacitor field in recent years. In order to explore this scientific problem, such carbon materials were prepared through pyrolysis of N-rich polymers such as melamine formaldehyde resin and polyaniline. Although these carbons possess low apparent specific surface areas of no more than 60 m² g⁻¹, their areal capacitance could reach up to an abnormally high value of 252 μF cm⁻². The results of systematical materials characterizations and electrochemical measurements show that these carbons contain numerous ultramicropores which could not be detected by the adsorbate of N₂ but are accessible to CO₂ and electrolyte ions. These ultramicropores play dominant roles in the charge storage process for these low apparent surface area carbons, leading to an energy storage mechanism of electric double layer capacitance. The contribution of pseudocapacitance to the total capacitance is calculated to be less than 15%. This finding challenges the widely accepted viewpoint that the high capacitance of N-doped carbon is mainly attributed to the pseudocapacitance generated from the faradic reactions between nitrogen functionalities and electrolyte.     

Effect of various porous nanotextures on the reversible electrochemical sorption of hydrogen in activated carbons

The reversible hydrogen storage capacity of three series of activated carbons (ACs) prepared from different precursors by KOH, CO₂ and steam activation is determined by electrodecomposition of an alkaline water solution and is correlated with the nanotextural parameters of ACs. Galvanostatic charge/discharge appears as a precise quantitative method for estimating the hydrogen sorption capacity, whereas, cyclic voltammetry supplies a very useful information on the electrosorption mechanism. For the ACs studied, the hydrogen sorption capacity is not linearly related with any of the porosity parameters commonly used in other publications, such as the Dubinin-Radushkevich micropore volumes determined by nitrogen or carbon dioxide adsorption, VDR N₂ and VDR CO₂. In particular, an important discrepancy is observed for the KOH activated materials, suggesting that this treatment may provoke changes of pore shape. A better correlation is found considering the nanopore size distribution obtained from CO₂ adsorption by the DFT method. The amount of hydrogen reversibly adsorbed demonstrates a proportional trend with the volume of micropores smaller than 0.6-0.7 nm. However, in all cases, a part of the micropore volume estimated by CO₂ adsorption is ineffective, suggesting that some ultramicropores are involved in irreversible trapping of hydrogen.     

Optimisation of supercapacitors using carbons with controlled nanotexture and nitrogen content

In order to optimize the performance of supercapacitors, the capacitance of the carbon materials used as electrodes was strictly related to their pores size and also to their redox properties. Well-sized carbons have been elaborated through a template technique using mesoporous silica. For a series of template carbons, a perfect linear dependence has been found for the capacitance values versus the micropore volume determined by CO₂ adsorption. The redox properties of carbons were enhanced by substituting nitrogen for carbon up to ca. 7 wt.%. For carbons with similar nanotextural characteristics, the electrochemical measurements showed a proportional increase of the specific capacitance with the nitrogen content in acidic electrolyte. For an activated carbon from polyacrylonitrile with a specific surface area of only 800 m² g⁻¹, but with a nitrogen content of 7 wt.%, the capacitance reaches 160 F g⁻¹, with very little fading during cycling.     

Structure and hydrogen adsorption properties of low density nanoporous carbons from simulations

We systematically model the hydrogen adsorption in nanoporous carbons over a wide range of carbon bulk densities (0.6–2.4 g/cm³) by using tight binding molecular dynamics simulations for the carbon structures and thermodynamics calculations of the hydrogen adsorption. The resulting structures are in good agreement with the experimental data of ultra-microporous carbon (UMC), a wood-based activated carbon, as indicated by comparisons of the microstructure at atomic level, pair distribution function, and pore size distribution. The hydrogen adsorption calculations in carbon structures demonstrate both a promising hydrogen storage capacity (excess uptake of 1.33 wt.% at 298 K and 5 MPa, for carbon structures at the lower range of densities) and a reasonable heat of adsorption (12–22 kJ/mol). This work demonstrates that increasing the heat of adsorption does not necessarily increase the hydrogen uptake. In fact, the available adsorption volume is as important as the isosteric heat of adsorption for hydrogen storage in nanoporous carbons.     

Enhancement of CO2 adsorption on phenolic resin-based mesoporous carbons by KOH activation

Carbons with high surface area and large volume of ultramicropores were synthesized for CO₂ adsorption. First, mesoporous carbons were produced by soft-templating method using triblock copolymer Pluronic F127 as a structure directing agent and formaldehyde and either phloroglucinol or resorcinol as carbon precursors. The resulting carbons were mainly mesoporous with well-developed surface area, large total pore volume, and only moderate CO₂ uptake. To improve CO₂ adsorption, these carbons were subjected to KOH activation to enhance their microporosity. Activated carbons showed 2–3-fold increase in the specific surface area, resulting from substantial development of microporosity (3–5-fold increase in the micropore volume). KOH activation resulted in enhanced CO₂ adsorption at 760 mmHg pressure: 4.4 mmol g⁻¹ at 25 °C, and 7 mmol g⁻¹ at 0 °C. This substantial increase in the CO₂ uptake was achieved due to the development of ultramicroporosity, which was shown to be beneficial for CO₂ physisorption at low pressures. The resulting materials were investigated using low-temperature nitrogen physisorption, CO₂ sorption, and small-angle powder X-ray diffraction. High CO₂ uptake and good cyclability (without noticeable loss in CO₂ uptake after five runs) render ultramicroporous carbons as efficient CO₂ adsorbents at ambient conditions.     

Hydrogen storage on chemically activated carbons and carbon nanomaterials at high pressures

Hydrogen adsorption measurements have been carried out at different temperatures (298 K and 77 K) and high pressure on a series of chemically activated carbons with a wide range of porosities and also on other types of carbon materials, such as activated carbon fibers, carbon nanotubes and carbon nanofibers. This paper provides a useful interpretation of hydrogen adsorption data according to the porosity of the materials and to the adsorption conditions, using the fundamentals of adsorption. At 298 K, the hydrogen adsorption capacity depends on both the micropore volume and the micropore size distribution. Values of hydrogen adsorption capacities at 298 K of 1.2 wt.% and 2.7 wt.% have been obtained at 20 MPa and 50 MPa, respectively, for a chemically activated carbon. At 77 K, hydrogen adsorption depends on the surface area and the total micropore volume of the activated carbon. Hydrogen adsorption capacity of 5.6 wt.% at 4 MPa and 77 K have been reached by a chemically activated carbon. The total hydrogen storage on the best activated carbon at 298 K is 16.7 g H₂/l and 37.2 g H₂/l at 20 MPa and 50 MPa, respectively (which correspond to 3.2 wt.% and 6.8 wt.%, excluding the tank weight) and 38.8 g H₂/l at 77 K and 4 MPa (8 wt.% excluding the tank weight).     

Advances in the study of methane storage in porous carbonaceous materials

This paper presents an overview of the results of our research group in methane storage, in which the behaviour of different carbon materials in methane storage has been studied. These materials include physically activated carbon fibres (ACFs), chemically activated carbons (ACs) and activated carbon monoliths (ACMs), all of them prepared in our laboratories. These results have been compared with those corresponding to commercial ACFs, commercial activated carbon cloths and felts, and a commercial activated carbon.An in depth analysis (different raw materials, activating agent and preparation variables) has been done in order to obtain the carbon material with the best methane adsorption capacity by unit volume of adsorbent. The important effect of the micropore volume, micropore size distribution (MPSD) and packing density of the carbon materials in the methane adsorption capacity and delivery has been analysed. After this study, activated carbons with volumetric methane uptake as high as 166 v/v and delivery of 145 v/v have been prepared. In addition, ACM with methane uptake of 140 v/v and a delivery of 126 v/v has also been obtained.Moreover, the results corresponding to preliminary in situ small angle neutron scattering (SANS) study of CD₄ adsorption under pressure in different porous carbons and a zeolite are also included. These experiments have established SANS as a viable technique to investigate high-pressure methane adsorption. CD₄ adsorption at supercritical conditions produces changes in the SANS curves. The changes observed are in agreement with theoretical speculations that the density of the adsorbed phase depends upon the pore size.     

Removal of dibenzothiophenes in kerosene by adsorption on rice husk activated carbon

The capacity of rice husk activated carbon (RHAC) to adsorb refractory sulfur compounds of dibenzothiophenes (DBTs) from commercial kerosene was evaluated in terms of their textural and chemical characteristics. Rice husk activated at 850 °C for 1 h showed an acceptable adsorption capacity for DBTs, despite a much lower specific surface area (473 m²/g) and total pore volume (0.267 cm³/g), when compared to micro-porous activated carbon fiber with a large specific surface area (2336 m²/g) and total pore volume (1.052 cm³/g). The volumes of ultramicropores acting as DBTs adsorption sites, and of mesopores leading DBTs into the ultramicropores were closely related to the DBTs adsorption capacity of the RHACs.     

Molecular hydrogen and spiltover hydrogen storage on high surface area carbon sorbents

A series of templated carbons with various high surface areas (2033–3798 m²/g) have been prepared using various microporous zeolites as hard templates. Molecular hydrogen storage and spiltover hydrogen storage on these templated carbons were investigated and compared with superactivated carbon AX-21 and other reported porous carbon sorbents at 298 K and 100 atm. Two relationships between the surface areas of these carbons and their hydrogen capacities were obtained. The relationship between molecular hydrogen capacity and surface area showed a 0.23 wt.% H₂/1000 m²/g of carbon sorbent at 298 K and 100 atm, indicating that merely increasing surface areas of the carbon sorbents cannot achieve a significant molecular hydrogen capacity at ambient temperature. Spiltover hydrogen storage was achieved by doping Pt nanoparticles (as dissociative hydrogen source) on these carbons (spiltover hydrogen receptor). Our first result on the relationship between the spiltover hydrogen capacity and surface area showed 0.4 wt.% H₂/1000 m²/g of carbon sorbent at 298 K and 100 atm, which indicated that storage via spillover can lead to an average of 70% enhancement compared to molecular hydrogen storage.     

Synthesis, characterization and energy-related applications of carbide-derived carbons obtained by the chlorination of boron carbide

A nanoporous carbide-derived carbon (CDC) was synthesized by chlorination of boron carbide powder using hydrogen chloride as the reactive gas. The structure and texture of the CDCs were characterized by X-ray diffraction, high-resolution transmission electron microcopy and nitrogen adsorption at 77 K, which confirmed a structural and textural dependence on chlorination temperature and reaction time. The CDC technique to produce porous carbons is very attractive because it can obtain carbons with desired structure and porosity and the CDCs produced here show great potential for energy-related applications. Used as hydrogen storage materials, the hydrogen uptake capacity could reach 1.06 wt.% at 77K and 1 bar. When tested as electrodes for supercapacitors, specific surface capacitance value up to 0.403 F m⁻² and a capacitance retention ratio up to 86% (at a voltage scan rate of 50 mV s⁻¹) could be obtained.     

Correlation of methane uptake with microporosity and surface area of chemically activated carbons

Two series of activated carbon discs have been prepared by chemical activation of olive stones with ZnCl₂ and H₃PO₄. Some of the carbons have been post-treated in order to modify their porous texture and/or surface chemical composition. All carbons have been characterized by adsorption of N₂ (−196 °C) and CO₂ (0 °C) and immersion calorimetry into dichloromethane. The volume of methane adsorbed at 25 °C and 3.5 MPa is proportional to the surface area deduced from immersion calorimetry into dichloromethane. Consequently, it is possible to estimate, using a single experiment, the possibility of using activated carbons for the storage of natural gas. On the other hand, the methane uptake can be also correlated to the volume of micropores, provided by the adsorption of N₂ at −196 °C and CO₂ at 0 °C, although the correlations is not as good. Only carbons slightly activated, with low surface area and microporosity below around 0.6 nm, do not adjust the above correlations because they adsorb more methane than the expected, the effect of chemical nature of the carbon surface being almost negligible.     

Adsorption of hydrogen sulphide (H2S) by activated carbons derived from oil-palm shell

Adsorption of hydrogen sulphide (H₂S) onto activated carbons derived from oil palm shell, an abundant solid waste from palm oil processing mills, by thermal or chemical activation method was investigated in this paper. Dynamic adsorption in a fixed bed configuration showed that the palm-shell activated carbons prepared by chemical activation (KOH or H₂SO₄ impregnation) performed better than the palm-shell activated carbon by thermal activation and a coconut-shell-based commercial activated carbon. Static equilibrium adsorption studies confirmed this experimental result. An intra-particle Knudsen diffusion model based on a Freundlich isotherm was developed for predicting the amount of H₂S adsorbed. Desorption tests at the same temperature as adsorption (298 K) and at an elevated temperature (473 K) were carried out to confirm the occurrence of chemisorption and oxidation of H₂S on the activated carbon. Surface chemistries of the palm-shell activated carbons were characterized by Fourier transform infrared spectroscopy and Boehm titration. It was found that uptaking H₂S onto the palm-shell activated carbons was due to different mechanisms, e.g. physisorption, chemisorption and/or H₂S oxidation, depending on the activation agent and activation method.     

An investigation of the effects of pyrolysis parameters on gas separation properties of carbon materials

A significant extension of an earlier analysis of molecular sieving carbons formed from polymeric precursors is reported for separation of important gas pairs including O₂/N₂, CO₂/CH₄ and C₃H₆/C₃H₈. Previously, it was shown that changing the time or temperature of the pyrolysis protocol for a commercially available polyimide (Matrimid^®) altered the final properties of the carbons produced. Changing the precursor material was shown in this study to also affect the final carbon material obtained for a given final pyrolysis temperature. Analysis of low temperature carbon dioxide adsorption isotherms using density functional theory was employed to characterize the microporosity of the materials. Results are given here for a totally different packing-inhibited polyimide precursor (6FDA/BPDA-DAM). Sorption, permeation and diffusion data are compared with those obtained using the more densely packed commercial polyimide precursor Matrimid^® studied earlier. Thermal soak was also investigated and the effect on permeation properties determined for carbons using both precursors. The results indicate that carbons from both precursors have size-selective ultramicropores as well as larger nonselective micropores that provide high capacity sorption sites for penetrants. High permselectivities, combined with high permeabilities are found for some of the samples when compared with conventional polymer materials. A hypothetical ultramicropore size distribution is shown to be useful to relate transport data to results from more commonly used characterization techniques such as pore size distribution analysis.     

Feasibility of tailoring for high isosteric heat to improve effectiveness of hydrogen storage in carbons

The idea that increasing the enthalpy of adsorption increases the adsorptive capacity of carbon and makes it a better storage material for hydrogen is examined here considering the entire adsorption-desorption cycle. Structural modifications of carbon are examined to reveal the complex relationships between the enthalpy of adsorption, the pore volume, and the amount of hydrogen delivered over the course of a single cycle. The results provide an understanding of the connection between enthalpy and effective storage capacity in carbon materials and serve as a guide toward the search for an adsorbent which satisfies the DOE targets. Extensive GCMC simulations show that carbons having single graphene walls are optimal for hydrogen storage and that attempts to increase the enthalpy of adsorption either by increasing the wall thickness or by decreasing the pore size are detrimental to adsorptive capacity over a complete cycle from charging to exhaustion. It is found that carbon nanotubes display the same trend as slit pore carbons. The search for an adsorbent suitable for hydrogen storage should be aimed at the discovery of an entirely new high-capacity adsorbent with an enthalpy of adsorption of 15 kJ/mol, intermediate between that of carbon (4-6 kJ/mol) and metal hydrides (30-75 kJ/mol).     

Specific anion and cation capacitance in porous carbon blacks

Porous carbon black was modified to introduce oxygen and nitrogen surface functionality and characterized using wet titration methods, elemental analysis, XPS, TEM, thermal analysis, adsorption of nitrogen and carbon dioxide. Then the electrochemical capacitance was measured for cations and anions in 1 M H₂SO₄. The results were compared to those obtained on activated carbons. The modified carbon black samples have four times higher adsorption of anions than cations. It is hypothesized that the graphitic microstructure of carbon blacks with structural defects is responsible for intercalation of anions in-between the graphene layers which take place at potentials higher than 0.75 V vs. Ag/AgCl and at moderately low current loads. This process is reversible and the deintercalation occurs at approximately 0.4 V vs. Ag/AgCl during the cathodic reduction. Introduction of nitrogen have generally a detrimental effect on the anion adsorption capacitance due to a structural defects blockage. At high current loads this phenomenon of enhanced anion adsorption capacitance becomes less pronounced due to the kinetic limitations. For amorphous activated carbons enhanced anion electrosorption at low current loads is governed by proton assistance while at high current loads larger cation capacitance is due to the pseudocapacitive interactions of protons with nitrogen and oxygen functional groups.     

Complexity of CO2 adsorption on nanoporous sulfur-doped carbons – Is surface chemistry an important factor?

Nanoporous S-doped carbon and its composites with graphite oxide were tested as adsorbents of CO₂ (1 MPa at 0 °C) after degassing either at 120 °C or 350 °C. The adsorption capacities were over 4 mmol/g at ambient pressure and 8 mmol/g at 0.9 MPa in spite of a low volume of micropores. The nitrogen adsorption experiments showed an increase in porosity upon an increase in the degassing temperature. The extent of this effect depends on the stability of surface groups. Interestingly, the CO₂ adsorption, especially at low pressure, was not affected. The good performance is due to the presence of ultramicropores similar in sizes to CO₂ molecule and to sulfur in various functionalities. Sulfur incorporated to aromatic rings enhances CO₂ adsorption via acid–base interactions in micropores. Moreover, sulfonic acids, sulfoxides and sulfones attract CO₂ via polar interactions. Hydrogen bonding of CO₂ with acidic groups on the surface can also play an important role in the CO₂ retention. These carbons have high potential for application as CO₂ removal media owing to their high degree of pore space utilization. The results obtained also show that high degassing temperatures might result in the decomposition of surface groups and thus in changes in surface interactions.     

The Characterization of the Micropore Structures of Some Activated Carbons of Plant Origin by N2 and CO2 Adsorptions

Abstract

In this study, active carbons prepared from almond and hazelnut shells under various experimental conditions were investigated. Merck-2514 and Merck-2184 active carbons were used for comparison. N₂ (77 K) gas and CO₂ (273 and 195 K) gas adsorptions were determined as comparison criteria. Regarding the specific surface area and micropore volume results obtained from these adsorption data, it is concluded that N₂ (77 K) adsorption by itself is inadequate in the characterization of active carbons which are low-sized microporous dominated. In addition, it is concluded that it would be useful to investigate CO₂ (195 and 273 K) adsorption. The iodine and methylene blue tests at 298 K were also applied for the characterization of the carbon adsorbents mentioned. From these data it was seen that the iodine test can be applied as a total porosity indicator and that the methylene blue test can be used as a developed microporosity indicator. These results indicate that the best adsorbents were those prepared from hazelnut shells. Depending on the preparation conditions, the physically activated carbon has an activation time up to 4 hours and has adsorption properties on the level of Merck commercial carbons.     

Modeling the selectivity of activated carbons for efficient separation of hydrogen and carbon dioxide

Grand canonical Monte Carlo simulations (GCMC) are carried out to investigate the separation of hydrogen and carbon dioxide via adsorption in activated carbons. In the simulations, both hydrogen and carbon dioxide molecules are modeled as Lennard-Jones spheres, and the activated carbons are represented by a slit-pore model. At elevated temperatures (T = 505 and 923 K), the activated carbons exhibit essentially no preference over the two gases and the selectivity of carbon dioxide relative to hydrogen falls monotonically as the pore size increases. At room temperature, however, the selectivity of carbon dioxide relative to hydrogen reaches up to 90, indicating that hydrogen and carbon dioxide can be efficiently separated. Furthermore, the optimized pore sizes, of width H = 1.48 nm for the bulk mole fraction ratio of x_CO2/x_H2=1:2 and H = 1.18 nm for x_CO2/x_H2=1:8, are identified in which the activated carbons show the highest selectivity for the separation of hydrogen and carbon dioxide.     

Facile synthesis of ultramicroporous carbon adsorbents with ultra-high CH4 uptake by in situ ionic activation

We introduce a straightforward method for the preparation of novel starch-based ultramicroporous carbons (SCs) that demonstrate high CH₄ uptake and excellent CH₄/N₂ selectivity. These SCs are derived from a combination of starch and 1–6 wt.% of acrylic acid, and the resulting materials are amenable to surface cation exchangeability as demonstrated by the formation of highly dispersed K⁺ in carbon precursors. Following activation, these SCs contain ultramicropores with narrow pore-size distributions of <0.7 nm, leading to porous carbon-rich materials that exhibit CH₄ uptake values as high as 1.86 mmol/g at 100 kPa and 298 K, the highest uptake value for CH₄ to date, with the IAST-predicted CH₄/N₂ selectivity up to 5.7. Both the potential mechanism for the formation of the narrow pores and the origin of the favorable CH₄ adsorption properties are discussed and examined. This work may potentially guide future designs for carbon-rich materials with excellent gas adsorption properties.     

Activation of carbon nanofibres for hydrogen storage

The present study was aimed to investigate different methods of activation of carbon nanofibres, CNF, in order to determine the beneficial effect on the hydrogen sorption capacities of increasing the surface area. Two activation systems were used: physical activation with CO₂ and chemical activation with KOH. A range of potential adsorbents were thus prepared by varying the temperature and time of activation. The structure of the CNF proved more suitable to activation by KOH than by CO₂, with the former yielding higher surface area carbons (up to 1000 m² g⁻¹). The increased surface area, however, did not correspond directly with a proportional increase in hydrogen adsorption capacity. Although high surface areas are important for hydrogen storage by adsorption on solids, it would appear that it is essential that not only the physical, but also the chemical, properties of the adsorbents have to be considered in the quest for carbon based materials, with high hydrogen storage capacities.