Nitrogen Removal Using Combined Ultracompact Biofilm Reactor-Packed Bed System

A predenitrification system consisting of an ultracompact biofilm reactor (UCBR) and a packed bed column was used for removing nitrogen from synthetically simulated wastewater. The UCBR column was maintained under aerobic conditions to favor nitrification process, while the packed bed column was operated under an anoxic environment for denitrification process. A peristaltic pump was used to recycle fluid between the anoxic-packed bed and aerobic-UCBR columns to facilitate nitrogen removal. Five recycle ratios (R) were investigated, namely, 3, 4, 5, 6, and 10. The highest average total nitrogen (TN) removal rate was achieved at R = 4. The NH4+–N, TN, and chemical oxygen demand (COD) removal rates at this R were 0.56±0.05?kg NH4+–N/m3/day, 0.39±0.09?kg TN/m3/day, and 1.83±0.18?kg COD/m3/day, respectively. It was noted that poor nitrification in the UCBR was accompanied by a corresponding reduction in overall TN removal efficiency. This observation suggested that nitrification process was the limiting step for TN removal in this setup. Thus, the performance of this predenitrification system could be enhanced by optimizing the performance of the nitrification process.     

Treatment of High-Strength Pharmaceutical Wastewater and Removal of Antibiotics in Anaerobic and Aerobic Biological Treatment Processes

Anaerobic and aerobic treatment of high-strength pharmaceutical wastewater was evaluated in this study. A batch test was performed to study the biodegradability of the wastewater, and the result indicated that a combination anaerobic-aerobic treatment system was effective in removing organic matter from the high-strength pharmaceutical wastewater. Based on the batch test, a pilot-scale system composed of an anaerobic baffled reactor followed by a biofilm airlift suspension reactor was designed. At a stable operational period, effluent chemical oxygen demand (COD) from the anaerobic baffled reactor ranged from 1,432 to 2,397?mg/L at a hydraulic retention time (HRT) of 1.25 day, and 979 to 1,749?mg/L at an HRT of 2.5 day, respectively, when influent COD ranged from 9,736 to 19,862?mg/L. As a result, effluent COD of the biofilm airlift suspension reactor varied between 256 and 355?mg/L at HRTs of from 5.0 to 12.5 h. The antibiotics ampicillin and aureomycin, with influent concentrations of 3.2 and 1.0?mg/L, respectively, could be partially degraded in the anaerobic baffled reactor: ampicillin and aureomycin removal efficiencies were 16.4 and 25.9% with an HRT of 1.25 day, and 42.1 and 31.3% with HRT of 2.5 day, respectively. Although effective in COD removal, the biofilm airlift suspension reactor did not display significant antibiotic removal, and the removal efficiencies of the two antibiotics were less than 10%.     

Single-Submerged Attached Growth Bioreactor for Simultaneous Removal of Organics and Nitrogen

The use of a single-unit, single-zone submerged attached growth bioreactor (SAGB) for the combined removal of carbonaceous organics and nitrogen from a municipal wastewater was demonstrated. A nitrification efficiency of 97% was achieved at a total organic loading of 3.47?kg?bCOD/m3?day. The total nitrogen loading varied from 0.2?to?0.3?kg?N/m3?day and resulted in effluent total nitrogen concentrations ranging from 4.2?to?8.5?mg/L. Concurrent denitrification was achieved at rates ranging from 0.077?to0.29?kg?N/m3?day. This single-unit SAGB, by providing dual treatment capacities, represents a cost-effective option that is particularly attractive for facilities with limited space and budget for system upgrade.     

Simultaneous Wastewater Nutrient Removal by a Novel Hybrid Bioprocess

A combined activated sludge–biofilm bioprocess called TNCU-I was developed by adding a rotating biological contactor to the aerobic zone of a traditional A2O process in order to solve the sludge retention time conflict between nitrifiers and phosphate accumulating organisms (PAOs), and the carbon source competition between denitrifiers and PAO. The TNCU-I process shows excellent carbon, nitrogen, and phosphate removal performance when treating synthetic wastewater. The process also achieved a more stable nitrification performance than the A2O process. The specific nitrification rate, the specific anoxic and aerobic phosphate uptake rates, the specific denitrification rate, and the specific anaerobic phosphate release rate were determined by a series of batch experiments. Such data were further analyzed to optimize the volume ratio of the TNCU-I anaerobic, anoxic, and aerobic tanks. The optimized process was also operated to confirm the performance. In addition, both Nitrosospira and Nitrospira were identified in the activated sludge and the rotating biological contactor biofilm by 16S rDNA based biotechnology.     

Strategy for Complete Nitrogen Removal in Bioreactor Landfills

Waste acclimation and batch microcosm studies containing digested municipal solid waste were conducted at different temperatures (22, 35, and 45°C) and gas-phase oxygen concentrations (0.7–100%, by volume) to provide guidance for field-scale implementation of in situ nitrogen removal processes. Results demonstrate that in situ ammonia–nitrogen is feasible in decomposed aerated solid waste environments at the gas-phase oxygen concentrations and temperatures evaluated and the potential for simultaneous nitrification and denitrification in field-scale bioreactor landfills is significant due to the presence of both aerobic and anoxic areas. Small amounts of oxygen were found sufficient for nitrification/ammonia removal to proceed, although removal rates increase with oxygen concentration. Laboratory results suggest field-scale implementation of in situ nitrogen removal occur in small dedicated treatment zones containing previously degraded waste (later in the life of a bioreactor landfill). Model simulations indicate removal of ammonia–nitrogen to low levels can occur with relatively short aeration depths (depth estimates ranged from 1.6 to 7.2?m below the point of leachate injection). Field-scale verification of these depth estimates is required prior to routine acceptance.     

Simultaneous Removal of Nitrogen and Phosphorous from Municipal Wastewater Using Continuous-Flow Integrated Biological Reactor

A pilot-scale experiment was carried out to study the simultaneous removal of nitrogen and phosphorous from municipal wastewater by an innovative continuous-flow integrated biological reactor (CIBR) process. A three-phase separator was used in the CIBR process, which not only saved energy consumption of sludge returning, but also solved the sludge–gas separating problem. The optimal working condition was 2?h aeration, 1?h agitation, and 1?h settling, with an energy consumption of 0.23?kW?h/m3. The average removal of chemical oxygen demand (COD), ammonia nitrogen (NH4+–N), total nitrogen (TN), and total phosphorus (TP) under the optimal conditions were 72.87, 75.23, 61.25, and 68.25%, respectively. The distributing rules of dissolved oxygen, pH, mixed liquid suspended solid, COD, NH4+–N, NO3?–N, TN, and TP in each phase of CIBR was studied. It was indicated that the appropriate condition was created for the simultaneous removal of nitrogen and phosphorus in the integrated reactor. The study demonstrated the feasibility of using CIBR process for simultaneous removal of nitrogen and phosphorus at the average temperature 12.2°C.     

Effect of Substrate Nitrogen/Chemical Oxygen Demand Ratio on the Formation of Aerobic Granules

The effect of the substrate nitrogen/chemical oxygen demand (N/COD) (mg/mg) ratio on the formation and characteristics of aerobic granules for simultaneous organic removal and nitrification were studied in four sequencing batch reactors operated at different substrate N/COD ratios ranging from 5/100 to 30/100. Results showed that aerobic granules formed at the substrate N/COD ratios studied, and both nitrifying and heterotrophic activities of aerobic granules were governed by the substrate N/COD ratio. The nitrifying activity was significantly enhanced with the increase of the substrate N/COD ratio, while the heterotrophic activity decreased. By determining elemental compositions of aerobic granules cultivated at different substrate N/COD ratios, it was revealed that the cell hydrophobicity was inversely related to the ratio of cell oxygen content to cell carbon content of aerobic granule. The production of extracellular polysaccharides showed a decreasing trend as the substrate N/COD ratio increased. This is probably due to enriched nitrifying population with the high N/COD ratios. This study clearly demonstrated that an aerobic granule-based sequencing batch reactor would have a great potential for simultaneous organic oxidation and nitrification.     

Horizontal-Flow Biofilm System with Step Feed for Nitrogen Removal

The aim of this study was to develop a simple biological system suitable for the treatment of dairy parlor wash waters. A novel horizontal-flow biofilm system with step feed was designed, constructed, and tested in the laboratory for organic carbon removal, nitrification, and denitrification of a synthetic dairy wastewater with average filtered chemical oxygen demand (CODf) of 2,060?mg/L, total nitrogen (TN) of 288?mg/L, and ammonia nitrogen (NH4–N) of 127?mg/L. The novel biofilm system consisted of two reactor units placed on top of one another, each comprising a stack of horizontal plastic sheets. Part of the wastewater was pumped onto Sheet 1 (top feed) and the remainder onto Sheet 11 (step feed) and flowed over the horizontal sheets down through the system. Three hydraulic loading rates were examined: 32.3, 25.1, and 19.3?L/m2?day, based on the top plan area, and the respective removals of CODf were 96, 96, and 97% and of TN, 86, 83, and 75% were achieved. The system was simple and cheap to construct and operate.     

Simultaneous Removal of Carbon and Nitrogen from Swine Wastewater Using an Immobilized-Cell Reactor

A single-stage phosphorylated polyvinyl alcohol immobilized-cell reactor with three operation modes was employed to investigate the efficiency of simultaneous carbon/nitrogen removal from raw swine wastewater. In continuous aeration mode, the removal efficiency of chemical oxygen demand (COD) and total nitrogen (T-N) exceeded 70 and 8%, respectively, at hydraulic retention time of 10?days. In intermittent aeration (IA) mode, the removal efficiency of COD and T-N was more than 85 and 46%, respectively, when the reactor was set at 50% aeration duration to cycle time to operate at three aerobic-anoxic cycles per day. When oxidation-reduction-potential control was adopted to control the duration of the anoxic period in the real-time controlled (RTC) IA mode for a 4?h aeration period, the total cycle time was reduced by about 20% with a slight increase in removal efficiency of COD (87%) and T-N (47%). The system with no extra chambers required is efficient in simultaneous carbon/nitrogen removal.     

Contrasting the Benefits of Primary Clarification versus Prefermentation in Activated Sludge Biological Nutrient Removal Systems

The potential benefits prefermentation can provide to biological nutrient removal are measured and compared to the costs of excess oxygen consumption and sludge production incurred by an activated sludge system that utilizes prefermentation, instead of primary clarification. Prefermentation was found to produce superior performance in regards to enhanced biological phosphorus removal. A lower soluble orthophosphorus effluent value [3.2?mg/L for the prefermented activated sludge (PAS) train versus 4.6?mg/L for the control train with primary clarification (PCAS)] and a higher percent phosphorus (% P) content of the biomass (9.0% for the PAS train versus 7.8% for the PCAS train) were both found to be statistically significant (P values of 4.26×10?5 and 0.0082, respectively). In addition statistically significant improvements in denitrification rates and reduced observed yields were observed due to prefermentation. However statistically significant increases in solids inventory and in particular oxygen uptake rates offset these improvements. Waste activated sludge production was slightly higher in the PAS train but was not found to be statistically significant.     

Combined Anaerobic/Aerobic Secondary Municipal Wastewater Treatment: Pilot-Plant Demonstration of the UASB/Aerobic Solids Contact System

Anaerobic pretreatment followed by aerobic posttreatment of municipal wastewater is being used more frequently. Recent investigations in this field using an anaerobic fluidized bed reactor/aerobic solids contact combination demonstrated the technical feasibility of this process. The investigation presented herein describes the use of a combined upflow anaerobic sludge bed (UASB)/aerobic solids contact system for the treatment of municipal wastewater and attempts to demonstrate the technical feasibility of using the UASB process as both a pretreatment unit and a waste activated sludge digestion system. The results indicate that the UASB reactor has a total chemical oxygen demand removal efficiency of 34%, and a total suspended solids removal efficiency of about 36%. Of the solids removed by the unit, 33% were degraded by the action of microorganisms, and 4.6% accumulated in the reactor. This low solids accumulation rate allowed operating the UASB reactor for three months without sludge wasting. The long solids retention time in this unit is comparable to the one normally used in conventional sludge digestion units, thus allowing the stabilization of the waste activated sludge returned to the UASB reactor. Particle flocculation was very poor in the UASB reactor, and therefore, it required postaeration periods of at least 100?min to proceed successfully in the aerobic unit. Polymer generation, which is necessary for efficient biological flocculation, was practically nonexistent in the anaerobic unit; therefore, it was necessary to maintain dissolved oxygen levels greater than 1.5?mg/L in the aerobic solids contact chamber for polymer generation to proceed at optimum levels. Once these conditions were attained, the quality of the settled solids contact chamber effluent always met the 30?mg BOD/L, 30?mg SS/L secondary effluent guidelines.     

Simultaneous Nitrogen and Phosphorus Removal in a Continuously Fed and Aerated Membrane Bioreactor

This research demonstrated the feasibility of simultaneous biological nitrogen and phosphorous removal in a single tank membrane bioreactor without cycling of air and/or feed through operation at a low dissolved oxygen (DO) and a high biomass concentration. Chemical oxygen demand removal efficiency was more than 98% and total nitrogen removal efficiency was 55%. Seventy-five percent of the total nitrogen removal was through simultaneous nitrification–denitrification (SND) and 25% through assimilation into the biomass. Interestingly, more than 98% phosphorous was removed and microbiological analysis showed the presence of polyphosphate-accumulating organisms in the activated sludge. The operating mixed-liquor suspended solids was between 16 and 23?g/L. The optimum DO was found to be 0.7–0.8?mg/L.     

Influence of COD/N Ratios on Simultaneous Removal of C and N Compounds in Biological Wastewater Treatment in Sequencing Fed-Batch Reactor and Kinetic Analysis

The impact of chemical oxygen demand/nitrogen (COD/N) values of feed wastewater on COD and nitrogen removal and biomass growth in a sequencing fed-batch reactor (SFBR) operation was investigated. The multiple microbial reactions involved in the simultaneous removal process of carbonaceous and nitrogenous components in the SFBR system were analyzed using a set of kinetics mathematical model. The results indicate that COD/N ratios strongly influence COD and total nitrogen removal efficiency. The COD removal efficiency per gram microorganism changed from 64.3 to 78.1% at COD/N = 11.9–2.5. The total nitrogen removal efficiency changed from 10.3 to 34.2% at COD/N = 2.5–11.9. However, variable COD/N ratios of feed wastewater are not marked for biomass growth rate.     

Combined Removal of Carbon and Nitrogen in an Integrated UASB-Jet Loop Reactor Bioreactor System

An innovative anaerobic–aerobic integrated bioreactor system consisting of an upflow anaerobic sludge blanket (UASB) and a jet loop reactor was developed to investigate the feasibility of combined removal of carbon and nitrogen for a low-strength wastewater at different hydraulic retention times (HRTs) and recycle ratios. Total chemical oxygen demand (COD) removal of the integrated system increased from 87 to 92%, at a combined system HRT of 44?h, when the recycle ratio was increased from 100 to 400%, respectively. Denitrification efficiency of the integrated system increased from 49 to 86%, at all HRTs, when the recycle ratio was increased from 100 to 400%. The integrated system, on average, achieved more than 78% of total nitrogen at all HRTs. Nitrogen content of the biogas produced from the UASB reactor increased with increase in recycle ratios while the methane content exhibited a reverse trend, irrespective of the HRTs. Sludge volume index of the UASB reactor increased from 15?to?42?mL/g total suspended solids at the end of the study. Specific methanogenic activity of the granular sludge decreased from 1.3 to 0.8 g CH4–COD/g volatile suspended solids per day at the end of the study. Nitrogen and COD mass balance of the integrated system indicated that a substantial amount of influent nitrogen and COD was lost in the effluent as dissolved form.     

Conditioning of Wastewater Sludge from Science-Based Industrial Park Using Freezing and Thawing

The Hsinchu Science-based Industrial Park (HSIP) is the main manufacturing base of “high-tech” commodities of Taiwan. The treatment of wastewater of HSIP produces hard-to-dewater sludge, at a rate of 80 Mg/day, which is resistant to chemical conditioning, whose disposal is costly. The use of chemical flocculation and physical conditioning, including heating and freezing and thawing, on the dewaterability of HSIP sludge was examined in this Note. The dewaterability of the original sludge was poor, and neither chemical flocculation nor thermal heating enhanced its dewatering. However, the freezing and thawing could release up to 83% of moisture from the sludge body; in line with this occurrence, the settleability and filterability of the sludge were considerably enhanced. The ice front developed during freezing, which could destroy the floc network, release the interstitial water, and might correspond to the successful conditioning using freezing and thawing.     

Simultaneous Removal of Organic Matter and Nitrogen Compounds in Autoaerated Biofilms

This paper describes the simultaneous removal of organic matter and nitrogen compounds carried out using an autoaerated multispecies biofilm growing on gas-permeable hollow-fiber membranes. In order to perform the aerobic heterotrophic oxidation and nitrification processes, the biofilm absorbs atmospheric oxygen through the inside walls of hollow fibers and consumes substrate from the bulk liquid. A mass balance calculated the consumed oxygen. Depending on the removed organic and nitrification rates, the oxygen flux through the hollow fibers can reach up to 90% of the total oxygen consumed, whereas the remaining 10% pertains to the dissolved oxygen from the influent wastewater. Without the biofilm the oxygen transfer rate through clean hollow fibers is 3.5?g?m?2?day?1, whereas the oxygen transfer rate through the biomembrane (hollow fiber+biofilm) achieves a maximum value of 25?g?m?2?day?1. The enhanced oxygen transfer using the biological pathway may be attributed, among many other factors, to the mobility of the microorganisms generating microturbulence, which produces more active bioturbulent diffusiveness than the molecular diffusion in the biofilm. It has also shown that the oxygen utilization efficiency was affected by the substrate utilization rate.     

Low-Strength Wastewater Treatment with Combined Granular Anaerobic and Suspended Aerobic Cultures in Upflow Sludge Blanket Reactors

Combined cultures were developed from anaerobic granular and suspended aerobic cultures in three upflow sludge blanket reactors aerated at 10?mL air/min 4?h/day (R2), every other day (R3), and 24?h/day (R4). The use of combined cultures was found to be advantageous compared to the anaerobic granules for the treatment of low-strength wastewaters. During municipal wastewater treatment at influent 5-day biochemical oxygen demand (BOD5) concentration of 53–118?mg/L (hydraulic retention time: 0.75?day), combined cultures in R2, R3, and R4 exhibited average BOD5 removal efficiencies of 52, 75, and 76%, respectively. The use of these cultures might be proposed as an alternative for municipal wastewater treatment due to their advantages such as achievement of required discharge standards, prevention of biomass loss/settleability problems unlike activated sludge systems and possible methanogenic activity, as well as high settling characteristics comparable to those of anaerobic granules.     

Use of a Sequencing Batch Reactor for Nitrogen and Phosphorus Removal from Municipal Wastewater

In this study, a suspended growth sequencing batch reactor (SBR) and an attached cum suspended growth SBR were used to investigate the performance characteristics of nitrogen and phosphorus (NP) removal from municipal sewage. The effects of three controlling factors, namely batch loading rate, feed pattern (initial feed or step feed), and mixing/aeration ratio, on NP removal were investigated under nine different experimental conditions. Owing to a large number of possible combinations among the controlling factors and different experimental conditions, it is very difficult to enumerate all the available combinations experimentally. In view of this, the Taguchi method, a cost-effective technique for design of experiments, was exploited for estimating the optimal operating condition. This study also evaluated the difference between the suspended growth SBR and the attached cum suspended growth SBR. The total nitrogen (TN), total phosphorus (TP), total biochemical oxygen demand (TBOD)5, and suspended solids (SS) removal efficiencies were 90.2, 83.9, 98.6, and 93.0%, respectively, for the suspended growth SBR. The corresponding values for the attached cum suspended growth SBR were 92.6, 82.1, 98.3, and 93.1%, respectively. It was observed that the batch loading rate influenced the efficiencies in terms of TN removal. It was also noted that step feed and mixing/aeration ratio had significant impact on TP removal performance. The optimal operating condition for the suspended growth SBR system in terms of batch loading rate, feed pattern, and mixing/aeration ratio were 0.170?mgBOD5/mgMLVSS?d, initial feed, and 1-to-1, respectively. The associated TN, TP, TBOD5, and SS removal efficiencies for the suspended growth SBR were 93.8, 98.2, 99.6, and 98.5%, respectively. The corresponding results for the attached cum suspended growth SBR system were 0.170?mgBOD5/mgMLVSS?d, initial feed, and 3-to-1, respectively. Similarly, the corresponding removal efficiencies for the attached cum suspended growth SBR were 94.7, 97.8, 99.3, and 98.8%, respectively.     

Nitrogen Transformations during Soil–Aquifer Treatment of Wastewater Effluent—Oxygen Effects in Field Studies

Depth-dependent oxygen concentrations and aqueous-phase total ammonia and nitrate/nitrite ion concentrations were measured in the field during the infiltration of wastewater effluent. Measurements illustrated the dependence of nitrogen fate and transport on oxygen availability. Infiltration basins were operated by alternating wet (infiltration) and dry periods. During infiltration periods, ammonia was removed within the top few feet of sediments via adsorption. Biochemical activity rapidly eliminated residual molecular oxygen in the infiltrate, making the soil profile anoxic. During dry periods, oxygen reentered the basin profile and sorbed ammonia was converted to nitrate via nitrification. Oxygen penetrated to a depth of about 0.6?m?(2?ft) within the first few days of dry periods. At greater depths, oxygen levels increased more slowly due to a combination of slow transport kinetics and biochemical (nitrogenous) oxygen demand. During normal wet/dry basin cycles consisting of about 4 wet and 4 dry days, the local vadose zone remained anoxic at depths greater than about 1.5?m?(5?ft) below land surface. As a consequence, conditions for denitrification were satisfied in the deeper sediments. That is, the nitrate nitrogen produced in near surface sediments moved freely downward with infiltrating water where it encountered an extensive anoxic zone before reaching local monitoring or extraction wells. The relative importance of dissolved organics and sorbed ammonia as electron donors for denitrification reactions remains to be established.     

Simultaneous Nitrogen and Phosphorus Removal Using a Double Sludge Switching Sequencing Batch Reactor

A new process using a sequencing batch reactor (SBR) and two smaller sludge hoppers is proposed for the simultaneous removal of phosphorus and nitrogen from wastewater. In the double sludge switching sequencing batch reactor, denitrifying phosphate accumulating bacteria (DPB) sludge and nitrification sludge are transferred to the SBR at different phases instead of flowing wastewater through different reactors. The process was operated with a cycle time of 10.5?h, consisting of DPB sludge filling phase (0.5?h), anaerobic phase I (2.0?h), settling and changing DPB sludge phase (0.5?h), anaerobic phase II (0.5?h), aerobic phase (4.0?h), settling and changing nitrifying sludge phase (0.5?h), and anoxic phase (3.0?h). Results of stable operation showed that the process was very efficient over a range of temperatures varied from 10?to?28°C. The average effluent concentrations and removal efficiencies were as follows: CODCr 28.0?mg/L, 92.1%; BOD5 7.0?mg/L, 95.1%; NH3–N 0.8?mg/L, 98.0%; TN 9.8?mg/L, 76.7%; and TP 0.5?mg/L, 92.3%.