Investigations on the performance and exhaust emissions of a diesel engine using preheated waste frying oil as fuel

In the present experimental investigation, waste frying oil a non-edible vegetable oil was used as an alternative fuel for diesel engine. The high viscosity of the waste frying oil was reduced by preheating. The properties of waste frying oil such as viscosity, density, calorific value and flash point were determined. The effect of temperature on the viscosity of waste frying oil was evaluated. It was determined that the waste frying oil requires a heating temperature of 135 °C to bring down its viscosity to that of diesel at 30 °C. The performance and exhaust emissions of a single cylinder diesel engine was evaluated using diesel, waste frying oil (without preheating) and waste frying oil preheated to two different inlet temperatures (75 and 135 °C). The engine performance was improved and the CO and smoke emissions were reduced using preheated waste frying oil. It was concluded from the results of the experimental investigation that the waste frying oil preheated to 135 °C could be used as a diesel fuel substitute for short-term engine operation.     

Experimental investigation of the performance and emissions of a heavy-duty diesel engine fueled with waste cooking oil biodiesel/ultra-low sulfur diesel blends

The major obstacle to biodiesel commercialization is the high cost of raw materials. Biodiesel from waste cooking oil is an economical source and thus an effective strategy for reducing the raw material cost. Using waste cooking oil also solves the problem of waste oil disposal. This study investigated the emissions of polycyclic aromatic hydrocarbons (PAHs), carcinogenic potencies and regulated matters, and brake specific fuel consumption from a heavy-duty diesel engine under the US-HDD transient cycle for five test fuels: ultra-low sulfur diesel (ULSD), WCOB5 (5 vol% biodiesel made from waste cooking oil + 95 vol% ULSD), WCOB10, WCOB20, and WCOB30. Experimental results indicate using ULSD/WCOB blends decreased PAHs by 7.53%-37.5%, particulate matter by 5.29%-8.32%, total hydrocarbons by 10.5%-36.0%, and carbon monoxide by 3.33%-13.1% as compared to using ULSD. The wide usage of WCOB blends as alternative fuels could protect the environment.     

The effect of biodiesel and bioethanol blended diesel fuel on nanoparticles and exhaust emissions from CRDI diesel engine

Biofuel (biodiesel, bioethanol) is considered one of the most promising alternative fuels to petrol fuels. The objective of the work is to study the characteristics of the particle size distribution, the reaction characteristics of nanoparticles on the catalyst, and the exhaust emission characteristics when a common rail direct injection (CRDI) diesel engine is run on biofuel-blended diesel fuels. In this study, the engine performance, emission characteristics, and particle size distribution of a CRDI diesel engine that was equipped with a warm-up catalytic converters (WCC) or a catalyzed particulate filter (CPF) were examined in an ECE (Economic Commission Europe) R49 test and a European stationary cycle (ESC) test. The engine performance under a biofuel-blended diesel fuel was similar to that under D100 fuel, and the high fuel consumption was due to the lowered calorific value that ensued from mixing with biofuels. The use of a biodiesel–diesel blend fuel reduced the total hydrocarbon (THC) and carbon monoxide (CO) emissions but increased nitrogen oxide (NO_x) emissions due to the increased oxygen content in the fuel. The smoke emission was reduced by 50% with the use of the bioethanol–diesel blend. Emission conversion efficiencies in the WCC and CPF under biofuel-blended diesel fuels were similar to those under D100 fuel. The use of biofuel-blended diesel fuel reduced the total number of particles emitted from the engine; however, the use of biodiesel–diesel blends resulted in more emissions of particles that were smaller than 50 nm, when compared with the use of D100. The use of a mixed fuel of biodiesel and bioethanol (BD15E5) was much more effective for the reduction of the particle number and particle mass, when compared to the use of BD20 fuel.     

The comparison of engine performance and exhaust emission characteristics of sesame oil–diesel fuel mixture with diesel fuel in a direct injection diesel engine

The use of vegetable oils as a fuel in diesel engines causes some problems due to their high viscosity compared with conventional diesel fuel. Various techniques and methods are used to solve the problems resulting from high viscosity. One of these techniques is fuel blending. In this study, a blend of 50% sesame oil and 50% diesel fuel was used as an alternative fuel in a direct injection diesel engine. Engine performance and exhaust emissions were investigated and compared with the ordinary diesel fuel in a diesel engine. The experimental results show that the engine power and torque of the mixture of sesame oil–diesel fuel are close to the values obtained from diesel fuel and the amounts of exhaust emissions are lower than those of diesel fuel. Hence, it is seen that blend of sesame oil and diesel fuel can be used as an alternative fuel successfully in a diesel engine without any modification and also it is an environmental friendly fuel in terms of emission parameters.     

Analysis of combustion characteristics,engine performance and exhaust emissions of diesel engine fueled with upgraded waste source fuel

Utilization of the waste products as an alternative fuel could reduce the dependence on fossil fuel. The three types of upgraded waste source fuels discussed in this paper were tire derived fuel (TDF), waste plastic disposal fuel (WPD) and upgraded waste cooking oil (UWCO). The detailed combustion pressure showed that kinematic viscosity and cetane number played an important role in determining the combustion quality. TDF's high kinematic viscosity and low cetane number affected its fuel vaporization process; thus, lengthening its ignition delay. UWCO showed the 14% higher power and 13.8% higher torque compared to diesel fuel (DF). WPD produced the lowest NOx due to its low pressure curve during combustion. TDF had produced the highest exhaust emissions (CO, CO₂, NO and NOx). Particulate matter (PM) emissions by UWCO blends were lower than DF. UWCO's soot concentration was 40% lower than DF and increased to 62.5% from low to high engine speed operation.     

Performance of a diesel engine fueled by waste cooking oil biodiesel

A direct injection diesel engine fueled by a diesel/biodiesel blend from waste cooking oil up to B100 (a blend of 100% biodiesel content) indicated a combustion efficiency rise by 1.8% at full load. The soot peak volume fraction was reduced by 15.2%, while CO and HC concentrations respectively decreased by 20 and 28.5%. The physical and chemical delay periods respectively diminished by 1.2 and 15.8% for engine noise to pronounce 6.5% reduction. Injection retarding by 5° reduced NO_x to those original levels of B0 (a blend of zero biodiesel content) and combined respective reduction magnitudes of 10 and 7% in CO and HC at 75% load. Increasing the speed reduced CO and HC respectively by 26 and 42% at 2.36 times the droplet average strain rate. By coupling the turbulence model to the spray break-up and chemical kinetics models, increasing the injection pressure simultaneously reduced CO, HC and NO_x at 17% exhaust gas recirculation ratio.     

Effects of turpentine and gasoline-like fuel obtained from waste lubrication oil on engine performance and exhaust emission

In this study, an experimental investigation was carried out to determine the effects of gasoline-like fuel (GLF), and its blends with turpentine with ratios of 10%, 20%, and 30% on the performance and emission characteristics of a gasoline engine. The GLF was obtained from waste lubrication engine oil by the method of pyrolitic distillation. Characteristics of the pure GLF and its blends were tested. A series of engine performance and emission tests were conducted using the fuel samples in the test engine. Performance parameters for each test were calculated utilizing measurement values of force exerted on the crank shaft, rate of air and fuel mass flow to the engine and engine speed. Effects of the fuels on the performance parameters, exhaust gas temperature, and emissions of NOx, CO, CO₂, and HC were discussed. The results indicated that torque, brake mean effective pressure and thermal efficiency increased but brake specific fuel consumption decreased with increasing amount of turpentine in the GLF sample. The main effect of 10%, 20% and 30% turpentine additions to GLF on pollutant formation was that the NOx ratio increased, whereas that of CO decreased.     

Investigation on combustion and emission characteristics of hydrogen-enriched dual-fuel engine operated under waste frying oil biodiesel

Using nonedible waste frying oil (WFO) as biodiesel and hydrogen in the mix composition may partly replace significant quantities of diesel fuel and help reduce fossil fuel reliance. The combination of diesel fuel, waste-fired biodiesel, and hydrogen gas can improve the performance, combustion, and emissions of single-fuel and dual-fuel diesel engines. This may lead to a novel alternative fuel mix pattern and modification for diesel engines, which is the research gap. Although there has been some research on waste-fired biodiesel and hydrogen gas-powered dual-fuel engines with the goal of partly replacing fossil fuels to a larger degree, there has been very little progress in this area. As a result, the current research effort focuses on using diesel fuel (100%, 30%, and 60%), waste-fired biodiesel (at 100%, 70%, and 40%), and hydrogen gas as fuel sources (5 and 10 liters per minute [LPM]). According to the current experiment, it was perceived in both dual-fuel and single-fuel modes. Under duel-fuel mode, the engine results for WFOB70D30 + H10 fuel blend had higher 4.2% (brake thermal efficiency [BTE]), 19.72% (oxides of nitrogen [NO_x]), and 9.09% (ignition delay [ID]) with a minimal range of (in-cylinder pressure, MFB, volumetric efficiency and heat release rate [HRR]) and a dropped rate of 4.34% (brake-specific energy consumption [BSEC]), 33.33% (carbon monoxide [CO]), 39.28% (hydrocarbons [HC]), 9.43% (smoke), and 6.97% (combustion duration [CD]) related to diesel fuel at peak load. However, single-fuel powered diesel engines provide minimal performance for the WFOB40D60 fuel blend with (11.32% lower BTE and 2.04% higher BSEC) and minimal rate of combustion (lower cylinder pressure, 2.12% minimal CD, 14.72% higher ID, minimal HRR combustion, volumetric efficiency, and MFB). Emitted fewer emissions (9.09% less CO, 4.87% less HC, 0.92% higher NO_x, and 1.69% more smoke) than diesel fuel at peak load. Therefore, it was concluded that adding 10 LPM of hydrogen gas to the biodiesel under a dual-fuel condition leads to better combustion, better performance, and less pollution than the single-fuel mode of operation.     

Fuel properties and exhaust emissions of low blending rate soybean oil methyl esters blended with diesel fuel

The main properties and engine emissions of low blending rate soybean oil methyl ester blended with diesel from 5 to 30 wt% were compared and analyzed. The experimental results show that, compared with diesel fuel, with an increase in the soybean oil methyl ester percentage in the blends, distillation temperature at 50%, flash point, kinematic viscosity, specific gravity, gelatine content, carbon residue, acidity and ash increase while a cold filter plugging point, solidifying point and copper corrosion keep constant, sulfur content decreases, smoke density and HC decrease while NO_x emission increase, CO increases at 2,200 r/min but decreases at 3,400 r/min.     

Performance, emissions and heat release characteristics of direct injection diesel engine operating on diesel oil emulsion

Emulsions of diesel and water are often promoted as being able to overcome the difficulty of simultaneously reducing emissions of both oxidises of nitrogen (NO_x) and particulate matter from diesel engines. In this paper we present measurements of the performance and NO_x and hydrocarbon emissions of a diesel engine operating on a typical diesel oil emulsion and examine through the use of heat release analysis differences found during its combustion relative to standard diesel in the same engine. While producing similar or greater thermal efficiency and improved NO_x and hydrocarbon emission outcomes, use of the emulsion also results in an increase in brake specific fuel consumption. Use of the emulsion is also shown to result in a retarded fuel injection, but smaller ignition delay for the same engine timing. As a result of these changes, cylinder pressures and temperatures are lower.     

Experimental investigation of the influence of blending on engine emissions of the diesel engine fueled by mahua biodiesel oil

The present article elaborates on the various emission characteristics of mahua oil with diesel fuel in a diesel engine at various blending conditions. Experimental investigation results are studied for various parameters such as exhaust emission of carbon monoxide (CO), hydrocarbon (HC), and oxides of nitrogen (NO) gases and exhaust gas temperature. Results show that residual oxygen, CO, HC, and NO emission were the lowest for mahua biodiesel compared with diesel. The experimental results proved that the use of mahua oil biodiesel as fuel in the diesel engine is a viable alternative to diesel fuel. Mahua biodiesel oil may be beneficial in decreasing greenhouse gas emissions without any engine modification. Mahua oil has the possibility of becoming a sustainable fuel source as biodiesel.     

Effect of injection parameters on the combustion and emission characteristics in a common-rail direct injection diesel engine fueled with waste cooking oil biodiesel

The objective of this paper was to study the effects of the injection pressure and injection timing on the combustion and emission characteristics in a single-cylinder common-rail direct injection (CRDI) diesel engine fueled with waste cooking oil (WCO) biodiesel and commercial diesel fuel. The fuel property including fatty acid composition for the biodiesel were measured and compared with those of the conventional diesel fuel. The engine tests were conducted at two injection pressures (80 and 160 MPa) and different injection timings from −25 to 0 crank angle degree (CAD) after top dead center (aTDC) under two different engine loads. The results showed that the indicated specific fuel consumption (ISFC) with respect to the injection timings of the biodiesel was higher than that of the diesel fuel under all experimental conditions. The peak cylinder pressure and the peak heat release rate of the biodiesel were slightly lower, while the ignition delay was slightly longer under all operating conditions. In terms of emissions, the biodiesel had benefits in reduction of smoke, carbon monoxide (CO), hydrocarbon (HC) emissions especially with high fuel injection pressure. The nitrogen oxide (NO_x) emissions of the biodiesel were relatively higher than those of the diesel under all experimental conditions.     

Production of diesel-like fuel from waste engine oil by pyrolitic distillation

The aim of this study is to obtain diesel-like fuel from waste lubrication engine oils by pyrolitic distillation method, which can be used in diesel engines. With this aim in mind, waste engine oil is collected in a tank, and it is purified from contaminants such as dust, heavy carbon soot, metal particles, gum-type materials and other impurities by filtering in the process prepared earlier. To investigate effects of additives known as sodium carbonate (NaCO₃), zeolite and lime (CaO) on density, viscosity, flash point, sulfur content, heating value and distillation temperature, the purified oil samples are blended separately with additives having mass basis of 2%, 4%, 6%, 8% and 10%. The mixed samples are exposed to pyrolitic distillation process to produce fuels to be used in engines. Thermal and physical properties of the produced fuels such as density, flash point, viscosity, sulfur content, heating value and distillation temperatures are examined. From these results, the CaO with a ratio of 2% has the highest effect on decreasing of sulfur content of the waste engine oil and on acquiring the most suitable distillation temperatures close to values of a diesel fuel. Diesel-like fuel (DLF) is obtained as 60% of the waste lubrication engine oil.     

Study on cottonseed oil as a partial substitute for diesel oil in fuel for single-cylinder diesel engine

The experiments were undertaken to obtain the knowledge necessary for raising the thermal efficiency of mixed oil composed of cottonseed oil and conventional diesel oil and for improving the performance of engine fuelled by the mixture. The experimental results obtained showed that a mixing ratio of 30% cottonseed oil and 70% diesel oil was practically optimal in ensuring relatively high thermal efficiency of engine, as well as homogeneity and stability of the oil mixture. A quadratic regressive orthogonal design test method was adopted in the experiment designed to examine the relationship between specific fuel consumption and four adjustable working parameters (intake-valve-closing angle (α), exhaust-valve-opening angle (β), fuel-delivery angle (θ) and injection pressure (P, in 10⁴ Pa)) when the above-mentioned oil mixture was used. The mathematical equations characterizing the relationship were formulated. The equation of specific fuel consumption derived from the regressive test under each operating condition was set as the objective function and the ranges for the four adjustable working parameters were the given constraint condition. Models of non-linear programming were then constructed. Computer-aided optimization of the working parameters for 30:70 cottonseed oil/diesel oil mixed fuel was achieved. It was concluded that the predominant factor affecting the specific fuel consumption was fuel-delivery angle θ, the approximate optimal value of which, in this specific case, was 3–5° in advance of that for engine fuelled by pure diesel oil. The experimental results also provided useful reference material for selection of the most preferable combination of working parameters.     

Influence of injection timing on performance, emission and combustion characteristics of a DI diesel engine running on waste plastic oil

Environmental concern and availability of petroleum fuels have caused interests in the search for alternate fuels for internal combustion engines. Waste plastics are indispensable materials in the modern world and application in the industrial field is continually increasing. In this context, waste plastics are currently receiving renewed interest. As an alternative, non-biodegradable, and renewable fuel, waste plastic oil is receiving increasing attention. The waste plastic oil was compared with the petroleum products and found that it can also be used as fuel in compression ignition engines. In the present work, the influence of injection timing on the performance, emission and combustion characteristics of a single cylinder, four stroke, direct injection diesel engine has been experimentally investigated using waste plastic oil as a fuel. Tests were performed at four injection timings (23°,20°,17° and 14° bTDC). When compared to the standard injection timing of 23° BTDC the retarded injection timing of 14° bTDC resulted in decreased oxides of nitrogen, carbon monoxide and unburned hydrocarbon while the brake thermal efficiency, carbon dioxide and smoke increased under all the test conditions.     

A cycle simulation model for predicting the performance of a diesel engine fuelled by diesel and biodiesel blends

Among the alternative fuels, biodiesel and its blends are considered suitable and the most promising fuel for diesel engine. The properties of biodiesel are found similar to that of diesel. Many researchers have experimentally evaluated the performance characteristics of conventional diesel engines fuelled by biodiesel and its blends. However, experiments require enormous effort, money and time. Hence, a cycle simulation model incorporating a thermodynamic based single zone combustion model is developed to predict the performance of diesel engine. The effect of engine speed and compression ratio on brake power and brake thermal efficiency is analysed through the model. The fuel considered for the analysis are diesel, 20%, 40%, 60% blending of diesel and biodiesel derived from Karanja oil (Pongamia Glabra). The model predicts similar performance with diesel, 20% and 40% blending. However, with 60% blending, it reveals better performance in terms of brake power and brake thermal efficiency.     

Effects of Fischer-Tropsch diesel fuel on combustion and emissions of direct injection diesel engine

Effects of Fischer-Tropsch (F-T) diesel fuel on the combustion and emission characteristics of a single-cylinder direct injection diesel engine under different fuel delivery advance angles were investigated. The experimental results show that F-T diesel fuel exhibits shorter ignition delay, lower peak values of premixed burning rate, lower combustion pressure and pressure rise rate, and higher peak value of diffusion burning rate than conventional diesel fuel when the engine remains unmodified. In addition, the unmodified engine with F-T diesel fuel has lower brake specific fuel consumption and higher effective thermal efficiency, and presents lower HC, CO, NO _x and smoke emissions than conventional diesel fuel. When fuel delivery advance angle is retarded by 3 crank angle degrees, the combustion duration is obviously shortened; the peak values of premixed burning rate, the combustion pressure and pressure rise rate are further reduced; and the peak value of diffusion burning rate is further increased for F-T diesel fuel operation. Moreover, the retardation of fuel delivery advance angle results in a further significant reduction in NO _x emissions with no penalty on specific fuel consumption and with much less penalty on HC, CO and smoke emissions. __________ Translated from Chinese Internal Combustion Engine Engineering, 2007, 28(2): 19–23 [译自: 内燃机工程]     

Exhaust emissions and electric energy generation in a stationary engine using blends of diesel and soybean biodiesel

The present work describes an experimental investigation concerning the electric energy generation using blends of diesel and soybean biodiesel. The soybean biodiesel was produced by a transesterification process of the soybean oil using methanol in the presence of a catalyst (KOH). The properties (density, flash point, viscosity, pour point, cetane index, copper strip corrosion, conradson carbon residue and ash content) of the diesel and soybean biodiesel were determined. The exhaust emissions of gases (CO, CO₂,C_xH_y,O₂, NO, NO_x and SO₂) were also measured. The results show that for all the mixtures tested, the electric energy generation was assured without problems. It has also been observed that the emissions of CO, C_xH_y and SO₂ decrease in the case of diesel–soybean biodiesel blends. The temperatures of the exhaust gases and the emissions of NO and NO_x are similar to or less than those of diesel.     

Characterisation and effect of using waste plastic oil and diesel fuel blends in compression ignition engine

Plastics have now become indispensable materials in the modern world and application in the industrial field is continually increasing. The properties of the oil derived from waste plastics were analyzed and found that it has properties similar to that of diesel. Waste plastic oil (WPO) was tested as a fuel in a D.I. diesel engine and its performance characteristics were analysed and compared with diesel fuel (DF) operation. It is observed that the engine could operate with 100% waste plastic oil and can be used as fuel in diesel engines. Oxides of nitrogen (NO_x) was higher by about 25% and carbon monoxide (CO) increased by 5% for waste plastic oil operation compared to diesel fuel (DF) operation. Hydrocarbon was higher by about 15%. Smoke increased by 40% at full load with waste plastic oil compared to DF. Engine fueled with waste plastic oil exhibits higher thermal efficiency upto 80% of the full load and the exhaust gas temperature was higher at all loads compared to DF operation.     

Biodiesel production from inedible animal tallow and an experimental investigation of its use as alternative fuel in a direct injection diesel engine

In this study, a substitute fuel for diesel engines was produced from inedible animal tallow and its usability was investigated as pure biodiesel and its blends with petroleum diesel fuel in a diesel engine. Tallow methyl ester as biodiesel fuel was prepared by base-catalyzed transesterification of the fat with methanol in the presence of NaOH as catalyst. Fuel properties of methyl ester, diesel fuel and blends of them (5%, 20% and 50% by volume) were determined. Viscosity and density of fatty acid methyl ester have been found to meet ASTM D6751 and EN 14214 specifications. Viscosity and density of tallow methyl esters are found to be very close to that of diesel. The calorific value of biodiesel is found to be slightly lower than that of diesel. An experimental study was carried out in order to investigate of its usability as alternative fuel of tallow methyl ester in a direct injection diesel engine. It was observed that the addition of biodiesel to the diesel fuel decreases the effective efficiency of engine and increases the specific fuel consumption. This is due to the lower heating value of biodiesel compared to diesel fuel. However, the effective engine power was comparable by biodiesel compared with diesel fuel. Emissions of carbon monoxide (CO), oxides of nitrogen (NO_x), sulphur dioxide (SO₂) and smoke opacity were reduced around 15%, 38.5%, 72.7% and 56.8%, respectively, in case of tallow methyl esters (B100) compared to diesel fuel. Besides, the lowest CO, NO_x emissions and the highest exhaust temperature were obtained for B20 among all other fuels. The reductions in exhaust emissions made tallow methyl esters and its blends, especially B20 a suitable alternative fuel for diesel and thus could help in controlling air pollution. Based on this study, animal tallow methyl esters and its blends with petroleum diesel fuel can be used a substitute for diesel in direct injection diesel engines without any engine modification.