DRYING OF SUGAR BEET FIBER WITH HOT AIR OR SUPERHEATED STEAM

A comparative study of drying thin layers of sugar beet fiber with hot air or with superheated steam in a specially designed pilot dryer is reported. Our present interests are focused on drying rate and on the quality of the dried product. Steam superheated at 130-150°C yields 90 % of dry matter (DM), however steam condensation on the cold product at the beginning of the process may penalize the drying time. The color of the fiber is not modified until reaching 80 % DM. Drying with air heated at temperatures lying in the 40 to 105°C range does not alter the white color up to 90 % DM. The water retention capacity of the original fiber, 14 g water/g DM remains unchanged whatever drying agent is used. The scaling up of the primary hot air drying set up to a ten times larger experimental dryer introduce no modification of drying time, water retention capacity or fiber color. Thick layer drying experiments permit to define parameters of a belt dryer for an industrial fiber processing plant.     

Drying Kinetics and Quality of Shrimp Undergoing Different Two-Stage Drying Processes

An innovative two-stage drying concept is presented in this article. The work considered drying of shrimp using a superheated steam dryer followed by a heat pump (SSD/HPD) or a hot air dryer (SSD/AD) both from drying kinetics and dried product quality points of view. The experiments were performed using the first-stage superheated steam drying temperature of 140°C while the second-stage heat pump drying (or hot air drying) was performed at 50°C. The moisture content of shrimp at the end of the superheated steam drying stage was varied between 30 and 40% (w.b.). The effect of tempering between SSD/HPD was also investigated. Shrinkage, color, rehydration behavior, texture (toughness and hardness), and microstructure of dried shrimp were measured. The results showed that SSD/HPD dried shrimp had much lower degree of shrinkage, higher degree of rehydration, better color, less tough and softer, and more porous than single-stage SSD dried shrimp. It was also found that SSD/AD gave redder shrimp compared to shrimp dried in a single-stage superheated steam dryer. No improvement in terms of shrinkage and rehydration behavior was observed, however.     

DRYING RATE AND TEMPERATURE PROFILE FOR SUPERHEATED STEAM VACUUM DRYING AND MOIST AIR DRYING OF SOFTWOOD LUMBER

Two charges of green radiata pine sapwood lumber were dried, either using superheated steam under vacuum (90°C, 0.2 bar abs.) or conventionally using hot moist air (90/60°C). Due to low density of the drying medium under vacuum, the circulation velocity used was 10 m/s for superheated steam drying and 5.0 m/s for moist air drying, and in both cases, the flow was unidirectional. In drying, stack drying rate and wood temperatures were measured to examine the differences between the superheated steam drying and drying using hot moist air.

The experimental results have shown that the stack edge board in superheated steam drying dried faster than in the hot moist air drying. Once again due to the low density of the steam under vacuum, a prolonged maximum temperature drop across load (TDAL) was observed in the superheated steam drying, however, the whole stack dried slower and the final moisture content distribution was more variable than for conventional hot moist air drying. Wood temperatures in superheated steam drying were lower.     

Drying Kinetics and Quality of Shrimp Undergoing Different Two-Stage Drying Processes

Abstract

An innovative two-stage drying concept is presented in this article. The work considered drying of shrimp using a superheated steam dryer followed by a heat pump (SSD/HPD) or a hot air dryer (SSD/AD) both from drying kinetics and dried product quality points of view. The experiments were performed using the first-stage superheated steam drying temperature of 140°C while the second-stage heat pump drying (or hot air drying) was performed at 50°C. The moisture content of shrimp at the end of the superheated steam drying stage was varied between 30 and 40% (w.b.). The effect of tempering between SSD/HPD was also investigated. Shrinkage, color, rehydration behavior, texture (toughness and hardness), and microstructure of dried shrimp were measured. The results showed that SSD/HPD dried shrimp had much lower degree of shrinkage, higher degree of rehydration, better color, less tough and softer, and more porous than single-stage SSD dried shrimp. It was also found that SSD/AD gave redder shrimp compared to shrimp dried in a single-stage superheated steam dryer. No improvement in terms of shrinkage and rehydration behavior was observed, however.     

DESORPTION ISOTHERMS AND DRYING CHARACTERISTICS OF SHRIMP IN SUPERHEATED STEAM AND HOT AIR

Desorption isotherms for shrimp were determined at the temperatures of 50, 60, 70 and 80°C. Amongst the moisture equilibrium predictions between the BET and GAB models, the latter has a better predictable capability. The GAB parameters are correlated with the temperatures by the Arrhenius expression. Drying characteristics of shrimp in drying media at the temperature range of 120-180°C for superheated steam and of 70-140°C for hot air have been examined. Drying rate and effective diffusion coefficient are used to quantify quantitatively the difference between the superheated steam and the hot air dryings. The temperature is more important effect on drying rate and effective diffusion coefficient in the superheated steam than in the hot air. Inversion temperature exists between 140 and 150°C. Comparing to the hot air, the shrimp dried by the superheated steam shows a lower degree of shrimp shrinkage. In addition, product colours are slightly different to those from the commercial sources.     

DRYING OF SLICED RAW POTATOES IN SUPERHEATED STEAM AND HOT AIR

Drying experiments were conducted on raw potato slices, using atmospheric pressure superheated steam and hot air as drying media at 170 and 240°C. Mass changes of the material were continuously measured, the conditions of cross section near the surfaces were observed with an electron microscope, also color changes of their surface were measured during drying. The respective drying methods and temperature conditions were compared and it was found that, in the case of superheated steam drying, moisture content temporarily increases due to steam condensation in the initial stage of drying, therewith, as well as starch gelatinization rapidly develops. Meanwhile, in case of hot air drying, starch gelatinization occurs more slowly than with superheated steam drying and that non-gelatinized starch granules remain on the surface when drying was completed. Furthermore, surface color measurements showed that samples dried by superheated steam were more reddish than ones dried by hot air and the surfaces were more glossy, because no starch granules remain on the surface in case of superheated steam drying.     

Quality Changes of Superheated Steam–Dried Fibers from Oil Palm Empty Fruit Bunches

Conventional drying of the fibers from oil palm empty fruit bunches (EFB) using flue gas from diesel burners frequently causes browning and dust explosion. Replacing the drying medium with superheated steam is expected to improve the quality of EFB fibers as well as improve the safety of the dryer operation. In this study, the effects of steam temperature and steam velocity on the quality of steam–dried EFB fibers was investigated. The drying experiment was carried out at atmospheric pressure with steam superficial velocity in the range of 0.3 to 0.49 m s^?1 and temperature in the range of 135 to 200°C. Three quality parameters of the EFB fibers, the color, strength, and microstructure, were used to assess the changes in EFB fiber quality as a result of superheated steam drying. The color of the EFB fiber was either improved or not significantly degraded. The strength of the superheated steam–dried EFB fibers was higher than that of undried and hot air–dried EFB fibers. The microstructure of fresh undried EFB fibers as seen by scanning electron microscopy (SEM) showed the presence of round silica particles of 10–20 µm in diameter all over the EFB fiber strand, which complicates pulping and bleaching. Superheated steam drying successfully removed the silica particles from the EFB fibers at temperatures of at least 200°C and a velocity of steam of at most 0.49 m s^?1, which is better than hammering, which can only remove 88% of the silica particles. The high temperature of the superheated steam loosened the silica particles from their craters. The EFB fibers cracked and split at steam velocities at or above 0.49 m s^?1 and high superheated steam temperatures at or above 200°C and as a consequence became weaker at these conditions. The removal of silica particles by superheated steam drying makes the EFB fiber amenable to pulping and bleaching. Superheated steam drying is therefore found to improve the overall quality of EFB fibers compared to hot air drying.     

Drying Kinetics and Sorption Isotherms of the Nejayote

The nixtamalization is an alkaline cooking process in corn tortillas industry that uses large quantities of water (5:1 corn weight) and producing a byproduct called nejayote. In this work, drying kinetic of insoluble fraction from nejayote was obtained using a hot air cabinet dryer at 60, 75, and 90°C. The air rate and water content were 1.5 m/s and 0.028 kg of water/kg of dry air, respectively. Sorption isotherms were measured by the COST method with sulfuric acid solutions at 30, 45 and 60°C. Results showed a difference in drying kinetics/drying time between drying temperatures of 60 and 75°C, and practically no difference between 75 and 90°C. This was probably due to the development of a superficial crust on the product. The shape of sorption curves was as expected; no temperature effect was identified but it is a common behavior for products with high sugar content. Finally the sorption isotherm was predicted based on primary chemical compounds (carbohydrates, proteins, crude fiber, and calcium hydroxide).     

FLASH DRYING OF FISH MEALS WITH SUPERHEATED STEAM: ISOTHERMAL PROCESS

The work considers the application of the flash drying to the moisture removal of fishmeal using superheated steam as transport medium. Heat, momentum and mass transfer equations were applied and an algorithm based on these equations was developed and solved. The model was validated using experimental data obtained in a pilot pneumatic dryer ( total length 60 m) provided with a steam jacket to maintain the superheated steam at a constant temperature. The drying time was less than 10 s to decrease the fish meals moisture content from 53.5% to 28% d.b. and in a second pass by the dryer the moisture down to 16.9% using superheated steam at It 1 ° C and 130 ° C in the jacket. The computational results are in agreement with the experimental data.     

A Comparative Study of Pork Drying Using Superheated Steam and Hot Air

Drying with superheated steam and hot air were comparatively studied for pork. Transport, physical, and chemical properties, i.e., effective diffusivity, color, microstructure, and rehydration ability, were investigated. The experimental results have shown that the decrease of pork moisture content in an early drying time was more rapid in superheated steam than in hot air and appeared to be lower in a latter time. The pork surface as examined by SEM was noticeably different for the samples dried by superheated steam and hot air. The fewer pores at the surface of superheated steam-dried pork caused a slower water penetration into the interior during rehydration, in addition to the lower drying rate. The color of the product from superheated steam was a relatively more intense brown than that obtained from hot air as presented by a lower L? value and a higher a? value.     

A Comparative Study of Pork Drying Using Superheated Steam and Hot Air

Drying with superheated steam and hot air were comparatively studied for pork. Transport, physical, and chemical properties, i.e., effective diffusivity, color, microstructure, and rehydration ability, were investigated. The experimental results have shown that the decrease of pork moisture content in an early drying time was more rapid in superheated steam than in hot air and appeared to be lower in a latter time. The pork surface as examined by SEM was noticeably different for the samples dried by superheated steam and hot air. The fewer pores at the surface of superheated steam-dried pork caused a slower water penetration into the interior during rehydration, in addition to the lower drying rate. The color of the product from superheated steam was a relatively more intense brown than that obtained from hot air as presented by a lower L* value and a higher a* value.     

Drying of Fish Press-Cake with Superheated Steam in a Pilot Plant Impingement System

Drying tests for pine sawdust and mackerel press-cake with hot air and with superheated steam were carried out in a pilot impingement cylindrical dryer. Wet particles move axially along the dryer, adjusting the inclination of the equipment, whereas hot gases circulate in cross-flow against the particles, forming a corotational impingement front. Feed rate and residence time of solids were studied experimentally as a function of dryer inclination for hot air and superheated steam as drying media. Drying rates and heat and mass transfer coefficients were found to increase at shorter residence times and higher gas temperatures. Dried mackerel press-cake with superheated steam resulted in a product with high moisture removal and very low losses of the valuable omega-3 fatty acids.     

Drying of Fish Press-Cake with Superheated Steam in a Pilot Plant Impingement System

Drying tests for pine sawdust and mackerel press-cake with hot air and with superheated steam were carried out in a pilot impingement cylindrical dryer. Wet particles move axially along the dryer, adjusting the inclination of the equipment, whereas hot gases circulate in cross-flow against the particles, forming a corotational impingement front. Feed rate and residence time of solids were studied experimentally as a function of dryer inclination for hot air and superheated steam as drying media. Drying rates and heat and mass transfer coefficients were found to increase at shorter residence times and higher gas temperatures. Dried mackerel press-cake with superheated steam resulted in a product with high moisture removal and very low losses of the valuable omega-3 fatty acids.     

COMBINED MICROWAVE AND SPOUTED BED DRYING OF DICED APPLES: EFFECT OF DRYING CONDITIONS ON DRYING KINETICS AND PRODUCT TEMPERATURE

The influence of microwave power (0 to 8.0 W/g, dry basis) and hot air temperature (25°C to 95 °C) on drying rate and product temperature of diced apples (from 31 % to 5% moisture content, dry basis) in a laboratory microwave and spouted-bed combined dryer was investigated. Product temperature initially increased sharply to a plateau about 12 to 15°C above the spouted bed air temperature at a microwave input power 6.4 W/g. This temperature remained almost constant thereafter. Uniform microwave heating was achieved as evidenced by uniform product color and product temperature. Drying rates increased with increasing spouted-bed air temperature or microwave power level, But higher microwave power caused more darkening of the product. Drying of the diced apples in the microwave and spouted bed drying system exhibited two falling rates periods. The influence of air temperature on effective moisture diffusivity followed an Arrhenius type equation. The activation energies were 23.7 kJ/mol and 26.7 kJ/mol for the first and second falling rate periods, respectively.     

Comparative Evaluation of Physical Properties of Edible Chitosan Films Prepared by Different Drying Methods

Edible films are alternative packaging, which have recently received much attention due mainly to environmental reasons. Edible films may be formed from edible biomaterials such as polysaccharides, proteins, or lipids. Among these biopolymers, chitosan is of interest because it has a good film-forming property and is biodegradable, biocompatible, and nontoxic. Several techniques have been used to prepare edible chitosan films with various degrees of success. However, it is always interesting to find an alternative technique to produce films of superior quality at shorter processing (drying) time. In this study, the influences of different drying methods and conditions on the drying kinetics and various properties of chitosan films were investigated. Drying at control conditions (ambient air drying and hot air drying at 40°C) as well as vacuum drying and low-pressure superheated steam drying (LPSSD) at an absolute pressure of 10 kPa were carried out at different drying temperatures (70, 80, and 90°C). The properties of chitosan films, in terms of color, tensile strength, percent elongation, water vapor permeability (WVP), glass transition temperature (T_g), and crystallinity, were also determined. Based on the results of both the drying behavior and film properties, LPSSD at 70°C was proposed as the most favorable conditions for drying chitosan films.     

DRYING OF SLICED RAW POTATOES IN SUPERHEATED STEAM AND HOT AIR

Drying experiments were conducted on raw potato slices, using atmospheric pressure superheated steam and hot air as drying media at 170 and 240°C. Mass changes of the material were continuously measured, the conditions of cross section near the surfaces were observed with an electron microscope, also color changes of their surface were measured during drying. The respective drying methods and temperature conditions were compared and it was found that, in the case of superheated steam drying, moisture content temporarily increases due to steam condensation in the initial stage of drying, therewith, as well as starch gelatinization rapidly develops. Meanwhile, in case of hot air drying, starch gelatinization occurs more slowly than with superheated steam drying and that non-gelatinized starch granules remain on the surface when drying was completed. Furthermore, surface color measurements showed that samples dried by superheated steam were more reddish than ones dried by hot air and the surfaces were more glossy, because no starch granules remain on the surface in case of superheated steam drying.     

DRYING RATE AND TEMPERATURE PROFILE FOR SUPERHEATED STEAM VACUUM DRYING AND MOIST AIR DRYING OF SOFTWOOD LUMBER

Abstract

Two charges of green radiata pine sapwood lumber were dried, either using superheated steam under vacuum (90°C, 0.2 bar abs.) or conventionally using hot moist air (90/60°C). Due to low density of the drying medium under vacuum, the circulation velocity used was 10 m/s for superheated steam drying and 5.0 m/s for moist air drying, and in both cases, the flow was unidirectional. In drying, stack drying rate and wood temperatures were measured to examine the differences between the superheated steam drying and drying using hot moist air.

The experimental results have shown that the stack edge board in superheated steam drying dried faster than in the hot moist air drying. Once again due to the low density of the steam under vacuum, a prolonged maximum temperature drop across load (TDAL) was observed in the superheated steam drying, however, the whole stack dried slower and the final moisture content distribution was more variable than for conventional hot moist air drying. Wood temperatures in superheated steam drying were lower.     

Study of Intermittent Low-Pressure Superheated Steam and Vacuum Drying of a Heat-Sensitive Material

Low-pressure superheated steam drying (LPSSD) has recently been applied to drying of various heat-sensitive foods and bioproducts with success. Several studies have shown that the quality of LPSSD-dried products is superior to that obtained using conventional hot air or vacuum drying. However, drying time and energy consumption for LPSSD is generally greater than that for vacuum drying. Therefore, it is necessary to examine different methodologies to improve the energy efficiency of LPSSD. An intermittent drying scheme is one possible method to reduce the energy consumption of the process while maintaining the desired product quality. In this study, the effect of intermittent supply of energy (through an electric heater and steam injection to the dryer) and vacuum (through the use of a vacuum pump) at various intermittency values or on:off periods (10:5, 10:10 and 10:20 min in the case of intermittent supply of energy and 5:0, 5:5, and 5:10 min in the case of intermittent supply of vacuum) at the on-period setting temperatures of 70, 80, and 90°C on the drying kinetics and heat transfer behavior of the drying samples (banana chips) was studied. The effects of these intermittent drying schemes and conditions on the quality parameters of dried banana chips; i.e., color, shrinkage, texture, and ascorbic acid retention, were also studied. Finally, the energy consumption values for intermittent LPSSD and vacuum drying were monitored through the effective (or net) drying time at various intermittent drying conditions and compared with those using continuous LPSSD and vacuum drying.     

Fast drying of cut tobacco in drop tube reactor and its effect on petroleum ether tobacco extracts

Entrained flow drying is an important fast drying tool in tobacco industry. This study used a drop tube reactor (DTR) as an entrained flow dryer to investigate drying process of flue-cured cut tobacco. Lab-scale cold and hot DTRs were set up to obtain drying kinetics for three types of cut tobacco using different drying gases and temperatures. The effective diffusion coefficients of cut tobacco in DTRs were compared with those in a general cylinder dryer. Moreover, the effects of different drying gases and temperatures on petroleum ether extract content were investigated. The results showed that the effective diffusion coefficients of cut tobacco in the DTRs were between 2.296?×?10^?8 and 8–6.244?×?10^?8?m²/s, which are two orders of magnitude higher than those in the cylinder dryer. Compared to hot air as a drying medium, superheated steam improved the effective diffusion coefficient of cut tobacco. The petroleum ether tobacco extract had a higher retention ratio when the superheated steam was used in the DTRs. An increase in the drying temperature resulted in a lower retention of the petroleum ether tobacco extract.     

Inversion Temperature and Pinch Analysis,Ways to Thermally Optimize Drying Processes

This work studies the compatibility and suitability of a combined inversion temperature and pinch analysis with the process selection for air and superheated steam spray drying of milk solids. The inversion temperature is a good starting point for an energy analysis because it is a simplified rate-based approach to comparing the steam and air drying systems. pinch analysis enables process integration, at least on a heat recovery and heat exchanger network level.

The resulting inversion temperature for the studied system was estimated as 182°C for the dryer inlet temperature. However, mass and energy balances showed that a minimum inlet temperature for spray drying of 184°C was required for the superheated steam dryer in order to ensure that the outlet solids temperature above the dew point temperature.

The inversion temperature is still very relevant in the early stages of a design process because it allows a quick assessment of which drying medium should result in a smaller dryer. It was evident that the steam system is better from an energy perspective because of the recoverable latent heat of the water vapor carried out of the dryer with the recycled steam. The steam system has between 82 and 92% of thermal energy recovery potential as condensable steam, compared with 13–30% energy recovery of the air system. However, other important design and operational factors are not discussed here in detail.

Combining the inversion temperature and pinch analysis suggests that superheated steam drying both gives better energy recovery and is likely to give smaller dryers for all operational conditions.