应用于软件无线电接收机中的无源下变频混频器

设计了一个应用于软件无线电接收机中的宽带无源下变频混频器,采用SMIC 0.13μm RF工艺实现,芯片面积0.42 mm<'2>.测试结果表明:在1.2 V电源电压下消耗了9 mA电流,工作频段0.9～2.2 GHz,电压转换增益17 dB,HP3 6～7 dBm,IIP2 40～42 dBm,DSB NF 17.5...     

A low-voltage folded-switching mixer in 0.18-/spl mu/m CMOS

Scaling of CMOS technologies has a great impact on analog design. The most severe consequence is the reduction of the voltage supply. In this paper, a low voltage, low power, AC-coupled folded-switching mixer with current-reuse is presented. The main advantages of the introduced mixer topology are: high voltage gain, moderate noise figure, moderate linearity, and operation at low supply voltages. Insight into the mixer operation is given by analyzing voltage gain, noise figure (NF), linearity (IIP3), and DC stability. The mixer is designed and implemented in 0.18-/spl mu/m CMOS technology with metal-insulator-metal (MIM) capacitors as an option. The active chip area is 160 /spl mu/m/spl times/200 /spl mu/m. At 2.4 GHz a single side band (SSB) noise figure of 13.9 dB, a voltage gain of 11.9 dB and an IIP3 of -3 dBm are measured at a supply voltage of 1 V and with a power consumption of only 3.2 mW. At a supply voltage of 1.8 V, an SSB noise figure of 12.9 dB, a voltage gain of 16 dB and an IIP3 of 1 dBm are measured at a power consumption of 8.1 mW.     

A highly linear receiver front-end employing modified derivative superposition method with tuned inductors for 5.25 GHz

We design a highly linear CMOS RF receiver front-end operating in the 5 GHz band using the modified derivative superposition (DS) method with one- or two-tuned inductors in the low noise amplifier (LNA) and mixer. This method can be used to adjust the magnitude and phase of the third-order currents at output, and thus ensure that they cancel each other out. We characterize the two front-ends by the third-order input intercept point (IIP3), voltage conversion gain, and a noise figure based on the TSMC 0.18 μm RF CMOS process. Our simulation results suggest that the front-end with one-tuned inductor in the mixer supports linearization with the DS method, which only sacrifices 1.9 dB of IIP3 while the other performance parameters are improved. Furthermore, the front-end with two-tuned inductors requires a precise optimum design point, because it has to adjust two inductances simultaneously for optimization. If the inductances have deviated from the optimum design point, the front-end with two-tuned inductors has worse IIP3 characteristic than the front-end with one-tuned inductor. With two-tuned inductors, the front-end has an IIP3 of 5.3 dBm with a noise figure (NF) of 4.7 dB and a voltage conversion gain of 23.1 dB. The front-end with one-tuned inductor has an IIP3 of 3.4 dBm with an NF of 4.4 dB and a voltage conversion gain of 24.5 dB. There is a power consumption of 9.2 mA from a 1.5 V supply.     

A Highly Linear Wideband Up-Conversion Differential CMOS Micromixer Using IMD3 Cancellation for a Digital TV Tuner IC

In this letter, a highly linear wideband up-conversion differential CMOS micromixer with a linearized transconductor employing a third order intermodulation (IMD3) cancellation technique for a digital TV tuner IC is proposed and designed. It is fabricated in a 0.18 $mu$ m CMOS process and draws 22 mA from a 1.8 V supply voltage. It shows a voltage gain of more than 6 dB, a noise figure lower than 11.9 dB, an IIP2 of more than 57 dBm, and an IIP3 of more than 18 dBm for the entire input band from 48 to 860 MHz.      

A dual-b and RF front-end of direct conversion receiver for wireless CDMA cellular phones with GPS capability

A highly integrated direct conversion receiver for cellular code division multiple access (CDMA) and GPS applications is successfully developed using a 0.5-/spl mu/m SiGe BiCMOS technology. The receiver consists of two low-noise amplifiers (LNAs), a dual-band mixer, two voltage-controlled oscillators (VCOs), a local-oscillator signal generation block, and channel filters. The CDMA LNA achieves a noise figure of 1.3 dB, an input-referred third-order intercept point (IIP3) of 10.9 dBm, and a gain of 15.3 dB with a current consumption of 9.8 mA in the high-gain mode. The mixer for the CDMA mode achieves an uncalibrated input-referred second-order intercept point of 53.7 dBm, an IIP3 of 6.4 dBm, a noise figure of 7.2 dB and a voltage gain of 37.2 dB. The phase noise of the CDMA VCO is approximately -133 dBc/Hz at a 900-kHz offset from a 1.762-GHz operating frequency. It exceeds all the CDMA requirements when tested on a handset.     

A direct conversion receiver with an IP2 calibrator for CDMA/PCS/GPS/AMPS applications

A second-order intercept point (IP2) calibration technique is developed using common-mode feedback (CMFB) circuitry in a direct-conversion receiver for wireless CDMA/PCS/GPS/AMPS applications. The IP2 calibrator is capable of providing different CMFB gain to tune its common-mode output impedance for each of the positive and negative mixer outputs. The CDMA mixer applying this method achieved a second-order input intercept point (IIP2) of 64 dBm, a third-order input intercept point (IIP3) of 4 dBm, a noise figure of 6.5 dB and a voltage gain of 42.2 dB. This result shows a 20 dB improvement from an uncalibrated IIP2 of 44 dBm. The receiver RFIC is implemented in a 0.5-/spl mu/m SiGe BiCMOS process, and it operates from a 2.7 to 3.1 V single power supply.     

A low power 3-5 GHz CMOS UWB receiver front-end

A novel low power RF receiver front-end for 3-5 GHz UWB is presented. Designed in the 0.13μm CMOS process, the direct conversion receiver features a wideband balun-coupled noise cancelling transconductance input stage, followed by quadrature passive mixers and transimpedance loading amplifiers. Measurement results show that the receiver achieves an input return loss below-8.5 dB across the 3.1-4.7 GHz frequency range, max-imum voltage conversion gain of 27 dB, minimum noise figure of 4 dB, IIP3 of-11.5 dBm, and IIP2 of 33 dBm. Working under 1.2 V supply voltage, the receiver consumes total current of 18 mA including 10 mA by on-chip quadrature LO signal generation and buffer circuits. The chip area with pads is 1.1 × 1.5 mm2.     

用于IEEE802．11b／g WLAN直接下变频接收机的射频前端设计

介绍了一种应用于IEEE802．11b／g无线局域网接收机射频前端的设计。基于直接下变频的系统架构。接收机集成了低噪声放大器、I／Q下变频器、去直流偏移滤波器、基带放大器和信道选择滤波器。电路采用TSMC0．18μm CMOS工艺设计,工作在2．4GHz ISM（工业、科学和医疗）频段,实现的低噪声放大器噪声系数为0．84dB,增益为16dB,S11低于-15dB,功耗为13mW;I／Q下变频器电压增益为2dB,输入1dB压缩点为-1 dBm,噪声系数为13dB,功耗低于10mw。整个接收机射频前端仿真得到的噪声系数为3．5dB,IIP3为-8dBm,IP2大于30dBm,电压增益为31dB,功耗为32mW。     

A dual-band RF front-end for WCDMA and GSM applications

An RF front-end for dual-band dual-mode operation is presented. The front-end consumes 22.5 mW from a 1.8-V supply and is designed to be used in a direct-conversion WCDMA and GSM receiver. The front-end has been fabricated in a 0.35-μm BiCMOS process and, in both modes, can use the same devices in the signal path except the LNA input transistors. The front-end has a 27-dB gain control range, which is divided between the LNA and quadrature mixers. The measured double-sideband noise figure and voltage gain are 2.3 dB, 39.5 dB, for the GSM and 4.3 dB, 33 dB for the WCDMA, respectively. The linearity parameters IIP3 and IIP2 are -19 dBm, +35 dBm for the GSM and -14.5 dBm and +34 dBm for the WCDMA, respectively     

一种用于超高频RFID阅读器的正交下变频混频器的分析与设计

分析了共用跨导级的正交下变频混频器的性能,包括电压转换增益、线性度、噪声系数和镜象抑制比,分析表明其在电流开关模式下比传统的Gilbert混频器对具有更好的性能.设计并优化了一个基于共用跨导级结构的用于超高频RFID阅读器的正交下变频混频器.在915MHz频段上,该混频器测得12.5dB的转换增益,10dBm的IIP3 ,58dBm的IIP2和17.6dB的SSB噪声系数.芯片采用0.18μm 1P6M RF CMOS工艺实现,在1.8V的电源电压下仅消耗3mA电流.     

一种高性能宽带直接变频射频前端设计

提出一种宽带(250 MHz~4.7 GHz)无电感BiCMOS射频前端结构,包含低噪声跨导放大器(LNTA)、带电阻无源混频器和跨阻级。低噪声跨导放大器使用了噪声和线性度消除技术,例如输入交叉耦合结构、互补输入和电流复用技术。带电阻无源混频器采用退化电阻来提高线性度。仿真结果表明, 当电源电压为3.3 V时,总电流为9.38 mA, 噪声系数为9.8 dB(SSB),电压转换增益为20 dB,输入3阶交调为+11.8 dBm。     

Design a novel 5.8 GHz wideband low noise amplifier in CMOS technology for WLAN applications

A novel complementary metal-oxide semiconductor (CMOS) low noise amplifier (LNA) was designed in this paper for wireless local area network (WLAN) applications in the 5.8?GHz ISM band. The LNA presents low voltage and low power dissipation design integrated in TSMC 0.18?µm standard CMOS technology and achieves a gain of 15.2?dB, a noise figure of 2.5?dB and an IIP3 of ?6.5?dBm with input return loss ?38.5?dB, output return loss of ?46.1?dB while dissipating just 4.96 mW from a 1V supply voltage.     

A low noise CMOS RF front-end for UWB 6-9 GHz applications

An integrated fully differential ultra-wideband CMOS RF front-end for 6-9 GHz is presented.A resistive feedback low noise amplifier and a gain controllable IQ merged folded quadrature mixer are integrated as the RF front-end. The ESD protected chip is fabricated in a TSMC 0.13μm RF CMOS process and achieves a maximum voltage gain of 23-26 dB and a minimum voltage gain of 16-19 dB,an averaged total noise figure of 3.3-4.6 dB while operating in the high gain mode and an in-band IIP3 of-12.6 dBm while in th...     

超宽带系统CMOS全集成射频收发器设计

本文介绍3.1-4.8GHz MB-OFDM系统的CMOS射频收发器。电路采用直接变频架构,由接收器、发射器和频率综合器组成。采用PGS隔离技术和其他隔离措施完成了单片射频收发器的版图布局。后仿真结果表明,接收链路可提供的最大增益为72dB,其52dB为可变增益,三个子频带内噪声系数介于5.2-7.8dB,带外IIP3不低于-3.4dBm。发射链路可提供的可控输出功率-8dBm到-2dBm,输出1dB压缩点不低于4dBm,输出信号边带抑制约44dBc,载波抑制不低于34dBc。频率综合器在三个频点间的跳变时间小于9ns。芯片采用Jazz0.18μm射频CMOS工艺设计,面积为6.1mm2。在1.8V电源电压下,总电流约221mA。     

用于蓝牙收发机的低电压CMOS Gilbert混频器

对已报道的Gilbert混频器工作在低电压时存在的问题进行了分析,在此基础上,描述了利用改进的低电压设计技术,用于2.4GHz蓝牙收发机的上混频器/下混频器的设计.利用适用于低电压工作的负反馈与电流镜技术提高上混频器的线性度;而通过采用折叠级联输出,增加了低电压时下混频器的设计自由度,从而降低了噪声,提高了转换增益.基于0.35μm CMOS工艺技术,在2V电源电压下,对电路进行了仿真.结果表明:上混频器消耗的电流为3mA,输入三阶截距点达到20dBm,输出的信号幅度为87mV;下混频器消耗的电流为3.5mA,得到的转换增益是20dB,输入参考噪声电压是6.5nV/ Hz,输入三阶截距点为4.4dBm.     

WLAN中带ESD保护的低噪声放大器设计

介绍了一个基于IBM0.18μmCMOS工艺,用于无线局域网(WLAN)IEEE802.11a的带ESD保护电路的低噪声放大器(LNA)。通过分析电感负反馈共源共栅放大器的输入阻抗、增益和噪声系数,以及ESD保护电路对低噪声放大器性能的影响,对该5GHz低噪声放大器进行设计和优化。测试结果表明,当电源电压为1.8V时,消耗电流为6.5mA,增益达到10dB,输入匹配达到-18dB,噪声为4.29dB,线性度IIP3为4dBm。     

A CMOS passive mixer with low flicker noise for low-power direct-conversion receiver

A CMOS passive mixer is designed to mitigate the critical flicker noise problem that is frequently encountered in constituting direct-conversion receivers. With a unique single-balanced passive mixer design, the resulted direct-conversion receiver achieves an ultralow flicker-noise corner of 45 kHz, with 6 dB more gain and much lower power and area consumption than the double-balanced counterpart. CMOS switches with a unique bias-shifting network to track the LO DC offset are devised to reduce the second-order intermodulation. Consequently, the mixer's IIP2 has been greatly enhanced by almost 21 dB from a traditional single-balanced passive mixer. An insertion compensation method is also implemented for effective dc offset cancellation. Fabricated in 0.18 /spl mu/m CMOS and measured at 5 GHz, this passive mixer obtains 3 dB conversion gain, 39 dBm IIP2, and 5 dBm IIP3 with LO driving at 0 dBm. When the proposed mixer is integrated in a direct-conversion receiver, the receiver achieves 29 dB overall gain and 5.3 dB noise figure.     

基于WCDMA接收机系统的低噪声放大器设计

介绍了低噪声放大器的基本工作原理,并对噪声源进行了分析。提出了采用先进的TSMC90 nm工艺,设计了一种基于WCDMA接收机系统的全差分拓扑共源共栅型低噪声放大器。该放大器片内集成了电感、电容,片外配置匹配网络。芯片测试结果表明:电路在2 GHz工作频率下,电压增益达到20 dB、噪声系数NF为1.4 dB、IIP3为-3.43 dBm。综合各项数据表明,该低噪声放大器具备良好的性能,可广泛适用于通讯系统之中。     

A 750 mV Fully Integrated Direct Conversion Receiver Front-End for GSM in 90-nm CMOS

The design of RF integrated circuits, at the low voltage allowed by sub-scaled technologies, is particularly challenging in cellular phone applications where the received signal is surrounded by huge interferers, determining an extremely high dynamic range requirement. In-depth investigations of 1/f noise sources and second-order intermodulation distortion mechanisms in direct downconversion mixers have been carried out in the recent past. This paper proposes a fully integrated receiver front-end, including LNA and quadrature mixer, supplied at 750 mV, able to meet GSM specifications. In particular, the direct downconverter employs a feedback loop to minimize second-order common mode intermodulation distortion, generated by a pseudo-differential transconductor, adopted for minimum voltage drop. For maximum dynamic range, the commutating pair is set with an LC filter. Prototypes, realized in a 90-nm RF CMOS process, show the following performances: 51 dBm IIP2, minimum over 25 samples, 1 dB desensitization point due to 3-MHz blocker at -18 dBm, 3.5 dB noise figure (NF), integrated between 1 kHz-100 kHz, 15 kHz 1/f noise corner. The front-end IIP2 has also been characterized with the mixer feedback loop switched off, resulting in an average reduction of 18 dB.     

Wide-band CMOS low-noise amplifier exploiting thermal noise canceling

Known elementary wide-band amplifiers suffer from a fundamental tradeoff between noise figure (NF) and source impedance matching, which limits the NF to values typically above 3 dB. Global negative feedback can be used to break this tradeoff, however, at the price of potential instability. In contrast, this paper presents a feedforward noise-canceling technique, which allows for simultaneous noise and impedance matching, while canceling the noise and distortion contributions of the matching device. This allows for designing wide-band impedance-matching amplifiers with NF well below 3 dB, without suffering from instability issues. An amplifier realized in 0.25-/spl mu/m standard CMOS shows NF values below 2.4 dB over more than one decade of bandwidth (i.e., 150-2000 MHz) and below 2 dB over more than two octaves (i.e., 250-1100 MHz). Furthermore, the total voltage gain is 13.7 dB, the -3-dB bandwidth is from 2 MHz to 1.6 GHz, the IIP2 is +12 dBm, and the IIP3 is 0 dBm. The LNA drains 14 mA from a 2.5-V supply and the die area is 0.3/spl times/0.25 mm/sup 2/.