Nonlinear flexural analysis of laminated composite plates using RBF based meshless method

The paper presents the nonlinear flexural response of laminated composite plates. The mathematical formulation of the actual physical problem of the laminated composite plate subjected to mechanical loading is presented utilizing higher order shear deformation theory and von-Karman nonlinear kinematics. These nonlinear governing differential equations of equilibrium are linearized using quadratic extrapolation technique. A meshfree technique based on multiquadric RBFs is used for analysis of the problems. Isotropic, orthotropic and laminated composite plates with immovable simply supported and clamped edges are analyzed.     

压电复合梁热机电耦合有限元模型

压电材料应用于航天结构形状或振动控制时,可能会受到热场、力场和电场的共同作用。为分析处于热场、力场和电场共同作用下的压电复合结构,文中基于高阶剪切变形理论、高阶电势模型和线性温度分布假设,利用虚功原理建立了压电复合梁结构的热-机-电耦合有限元模型。该模型可应用于热机电耦合压电复合结构的形状与振动控制研究。利用本文模型对压电双晶片梁、压电复合悬臂梁进行了数值仿真,仿真结果与文献给出的理论结果和实验值吻合良好,表明本文模型是正确有效的。     

Three-dimensional semi-analytical model for the static response and sensitivity analysis of the composite stiffened laminated plate with interfacial imperfections

For the stiffened composite laminated plates with interfacial imperfections, the problem of static response and sensitivity analysis was investigated in Hamilton system. Firstly, the meshfree formulation of Hamilton canonical equation for the composite laminated plate with interfacial imperfections was deduced by the linear spring-layer and the state-vector equation theory. And then, based on the equation of plates and stiffeners, governing equation of the composite stiffened laminated plate was assembled by using the spring-layer model again to ensure the compatibility of stresses and the discontinuity of displacements at the interface between plate and stiffeners. At last, a three-dimensional hybrid governing equation was developed for the static response analysis and sensitivity analysis.     

An adhesively laminated plate element for PZT smart plates

An adhesively laminated element taking into consideration peel stress is developed for a piezoelectric smart plate. In this novel finite element analysis formulation, a four node piezoelectric element is firstly derived, and an adhesive element of finite thickness with both shear and peel stiffness is sandwiched between two collocated four node plate elements to form an adhesively laminated element for a piezoelectric smart plate. In this framework of finite element analysis, because the displacement filed in this adhesively laminated element is continuous and a plate element is derived based on the Reissner–Mindlin plate theory, and thus it can be accurately applied to a thin or moderately thick host plate with bonded or debonded piezoelectric actuators and sensors. The formulation is performed for an isotropic host plate and a fiber reinforced laminate plate. Numerical results are presented to compare with those of the exact solutions for smart beams, and validate with the experimental results of the isotropic and composite host plates available in the literature. Using the present finite element analysis formulation, energy transfer stresses in the adhesive and equivalent forces induced in the host plate are investigated. The present formulation is demonstrated to allow debondings of piezoelectric patches and the debonding detection.The authors are grateful to the support of the Australian Research Council via a Discovery Projects grant (grant No: DP0346419).     

State space finite element analysis for piezoelectric laminated curved beam with variable curvature

ABSTRACT

A six-variable state vector formulation for static deformation of the laminated curved beam bonded with piezoelectric actuators is deduced. The 2D numerical solution for the piezoelectric laminated curved beams (PLCB) is explored. Then the distributions of the electrical and mechanical fields along the beam thickness direction are investigated analytically. The static shape control is researched for a laminated half circular beam covered with piezoelectric actuators. Comparisons with the available results show the reliability of the proposed method. At the end a spiral laminated piezoelectric structure is analyzed and the parameter study is carried out using the presented method.     

Performance of piezoelectric fiber-reinforced composites for active structural-acoustic control of laminated composite plates

This paper deals with the active structural acoustic control of thin laminated composite plates using piezoelectric fiber-reinforced composite (PFRC) material for the constraining layer of active constrained layer damping (ACLD) treatment. A finite element model is developed for the laminated composite plates integrated with the patches of ACLD treatment to describe the coupled structural-acoustic behavior of the plates enclosing an acoustic cavity. The performance of the PFRC layers of the patches has been investigated for active control of sound radiated from thin symmetric and antisymmetric cross-ply and antisymmetric angle-ply laminated composite plates into the acoustic cavity. The significant effect of variation of piezoelectric fiber orientation in the PFRC layer on controlling the structure-borne sound radiated from thin laminated plates has been investigated to determine the fiber angle in the PFRC layer for which the structural-acoustic control authority of the patches becomes maximum.     

Adhesive element modelling and weighted static shape control of composite plates with piezoelectric actuator patches

A novel finite element model is presented for static and dynamic analysis of composite plates integrated with a laminated piezoelectric layer, a host laminated composite plate and an adhesive layer between them. A new adhesive element is developed which includes both peel and shear effects in the adhesive layer based on first‐order shear deformation plate theory. The thin adhesive layer between the piezoelectric layer and the host plate is modelled by assuming that it carries constant shear and peel strains throughout its thickness. In addition, a weighted static shape control scheme for finding the optimal voltage distribution for static shape control is given. By selecting different weighting matrices, a variety of items such as displacements, slopes, curvatures, strains and even generalized forces, can be included in finding the optimal actuating voltage for static shape control. The present model is validated by comparing with those results available in the literature. The numerical results show that the weighted linear least method can give a satisfactory voltage distribution to best match the desired shape. Copyright © 2004 John Wiley & Sons, Ltd.     

A three-dimensional semi-analytical model for the composite laminated plates with a stepped lap repair

A three-dimensional semi-analytical model of the static response and sensitivity analysis was established based on the state space methods and meshless method for the composite laminated plates with a stepped lap repair. Firstly, the meshfree formulations of Hamilton canonical equation and the linear spring-layer were deduced by the radial point interpolation method (RPIM) shape functions and the modified Hellinger–Reissner (H–R) variational principle of elastic solids. And then a three-dimensional hybrid governing equation of the static response analysis and sensitivity analysis were developed for the composite laminated plates with a stepped lap repair. The present three-dimensional semi-analytical model with no initial assumptions regarding displacement and stress accounts for the transverse shear deformation and rotary in the governing equation of structure. By using the hybrid governing equation in the response analysis and sensitivity analysis, the convoluted algorithm can be avoided in sensitivity analysis, and the response quantities and the sensitivity coefficients can be obtained simultaneously.     

A new 4-node quadrilateral FE model with variable electrical degrees of freedom for the analysis of piezoelectric laminated composite plates

A new 4-node quadrilateral finite element is developed for the analysis of laminated composite plates containing distributed piezoelectric layers (surface bonded or embedded). The mechanical part of the element formulation is based on the first-order shear deformation theory. The formulation is established by generalizing that of the high performance Mindlin plate element ARS-Q12, which was derived based on the DKQ element formulation and Timoshenko’s beam theory. The layerwise linear theory is applied to deal with electric potential. Therefore, the number of electrical DOF is a variable depending on the number of plate sub-layers. Thus, there is no need to make any special assumptions with regards to the through-thickness variation of the electric potential, which is the true situation. Furthermore, a new “partial hybrid”-enhanced procedure is presented to improve the stresses solutions, especially for the calculation of transverse shear stresses. The proposed element, denoted as CTMQE, is free of shear locking and it exhibits excellent capability in the analysis of thin to moderately thick piezoelectric laminated composite plates.     

Finite element formulation for anisotropic coupled piezoelectro‐hygro‐thermo‐viscoelasto‐dynamic problems

A finite element algorithm has been developed for the efficient analysis of smart composite structures with piezoelectric polymer sensors or/and actuators based on piezoelectro‐hygro‐thermo‐viscoelasticity. Variational principles for anisotropic coupled piezoelectro‐hygro‐thermo‐viscoelasto‐dynamic problems have also been proposed in this study. As illustrative studies, dynamic responses in laminated composite beams and plates with PVDF sensors and actuators are obtained as functions of time using the present finite element procedures. The voltage feedback control scheme is utilized. The proposed numerical method can be used for analysing problems in the design of smart structures as well as smart sensors and actuators. Copyright © 1999 John Wiley & Sons, Ltd.     

A co-rotational 8-node assumed strain shell element for postbuckling analysis of laminated composite plates and shells

 The formulation of a nonlinear composite shell element is presented for the solution of stability problems of composite plates and shells. The formulation of the geometrical stiffness presented here is exactly defined on the midsurface and is efficient for analyzing stability problems of thin and thick laminated plates and shells by incorporating bending moment and transverse shear resultant forces. The composite element is free of both membrane and shear locking behaviour by using the assumed natural strain method such that the element performs very well as thin shells. The transverse shear stiffness is defined by an equilibrium approach instead of using the shear correction factor. The proposed formulation is computationally efficient and the test results showed good agreement. In addition the effect of the viscoelastic material is investigated on the postbuckling behaviour of laminated composite shells. Received: 6 February 2002 / Accecpted: 6 January 2003 ID=" Present address: School of Civil Engineering, Asian Institute of Technology     

An efficient meshfree method for vibration analysis of laminated composite plates

A detailed analysis of natural frequencies of laminated composite plates using the meshfree moving Kriging interpolation method is presented. The present formulation is based on the classical plate theory while the moving Kriging interpolation satisfying the delta property is employed to construct the shape functions. Since the advantage of the interpolation functions, the method is more convenient and no special techniques are needed in enforcing the essential boundary conditions. Numerical examples with different shapes of plates are presented and the achieved results are compared with reference solutions available in the literature. Several aspects of the model involving relevant parameters, fiber orientations, lay-up number, length-to-length, stiffness ratios, etc. affected on frequency are analyzed numerically in details. The convergence of the method on the natural frequency is also given. As a consequence, the applicability and the effectiveness of the present method for accurately computing natural frequencies of generally shaped laminates are demonstrated.     

Active structural-acoustic control of laminated composite plates using vertically/obliquely reinforced 1–3 piezoelectric composite patch

This article deals with the active structural-acoustic control of thin laminated composite plates using vertically reinforced 1–3 piezoelectric fiber-reinforced composite (PFRC) material for constraining layer of active constrained layer damping (ACLD) treatment. A finite element model is developed for the laminated composite plates integrated with ACLD patches and coupled with acoustic cavity to describe the coupled structural-acoustic behavior of the plates enclosing the cavity. Both in-plane and out of plane actuation of the constraining layer of the ACLD treatment have been utilized for deriving the finite element model. The analysis revealed that the vertical actuation dominates over the in-plane actuation. The performance of PFRC layers of the patches has been investigated for active control of sound radiated from thin symmetric and antisymmetric cross-ply and antisymmetric angle-ply laminated composite plates into the acoustic cavity.     

Vibration suppression of laminated composite beams with a piezo-electric damping layer

An analytical formulation is derived for modelling the behaviour of laminated composite beams with integrated piezoelectric sensor and actuator. The major difference in approach to the solution compared to previous studies is that the analytical solution for active vibration control and suppression of smart laminated composite beams is presented in this paper. The governing equation is based on the first-order shear deformation theory (Mindlin plate theory), which is applicable for both thin and moderately beams, and includes the coupling between mechanical and electrical deformations. The voltage generated by the sensor layer and response of the beam to the actuator voltage can be computed independently. In this study, the new assumption of harmonic vibration is introduced, which includes both of the sine and cosine terms. Another contribution of this paper is introducing the transformation method of complex numbers to reduce the order of the governing equation of smart laminated beams. Thus, the exact solution of the reduced governing equation can be obtained by using MATLAB and the entire numerical results are presented. The behaviour of the output voltage from the sensor layer and the input voltage acting on the actuator layer is also studied. Graphical results are presented to demonstrate the ability of closed-loop system to actively control the vibration of laminated beams and it shows a good control effect. The influence of stacking sequence on the controlled transient response of the laminated beam is examined. Finally, the experiential formulation of the amplitude of beam vibration varying with the negative velocity feedback control gain has also been evaluated. The present method has a general application in this field of study.     

Mesh‐free models for static analysis of smart laminated composite beams

This paper is concerned with the development of mesh‐free models for the static analysis of smart laminated composite beams. The overall smart composite beam is composed of a laminated substrate composite beam and a piezoelectric layer attached partially or fully at the top surface of the substrate beam. The piezoelectric layer acts as the distributed actuator layer of the smart beam. A layer‐wise displacement theory and an equivalent single‐layer theory have been used to derive the models. Several cross‐ply substrate beams are considered for presenting the numerical results. The responses of the smart composite beams computed by the present new mesh‐free model based on the layer‐wise displacement theory excellently match with those obtained by the exact solutions. The mesh‐free model based on the equivalent single‐layer theory cannot accurately compute the responses due to transverse actuation by the piezoelectric actuator. The models derived here suggest that the mesh‐free method can be efficiently used for the numerical analysis of smart structures. Copyright © 2016 John Wiley & Sons, Ltd.     

Control of geometrically nonlinear vibrations of skew laminated composite plates using skew or rectangular 1–3 piezoelectric patches

This paper deals with the analysis of active constrained layer damping (ACLD) of geometrically nonlinear transient vibrations of skew laminated composite plates using skew or rectangular patches of the ACLD treatment. The constraining layer of the patch of the ACLD treatment is composed of the vertically/obliquely reinforced 1–3 piezoelectric composite material. The Golla–Hughes–McTavish method has been used to model the constrained viscoelastic layer of the ACLD treatment in the time domain. A coupled electromechanical nonlinear three dimensional finite element model of skew laminated thin composite plates integrated with the skew or rectangular patches of ACLD treatment has been derived. The performance of the patches is investigated for different configurations of their placements on the top surface of the skew substrate plates. The analysis reveals that the ACLD treatment significantly improves the active damping characteristics of the skew laminated composite plates over the passive damping for suppressing their geometrically nonlinear transient vibrations. It is found that even though the substrate laminated plates are skew, a rectangular patch of the ACLD treatment located at the centre of the top surface of the substrate should be used for optimum damping of geometrically nonlinear vibrations of skew laminated composite plates irrespective of their skew angles and boundary conditions. The effects of piezoelectric fiber orientation angle and the skew angles of the substrate plates on the control authority of the ACLD patches have been emphatically investigated.     

Design of laminated piezocomposite shell transducers with arbitrary fiber orientation using topology optimization approach

Sensor and actuator based on laminated piezocomposite shells have shown increasing demand in the field of smart structures. The distribution of piezoelectric material within material layers affects the performance of these structures; therefore, its amount, shape, size, placement, and polarization should be simultaneously considered in an optimization problem. In addition, previous works suggest the concept of laminated piezocomposite structure that includes fiber‐reinforced composite layer can increase the performance of these piezoelectric transducers; however, the design optimization of these devices has not been fully explored yet. Thus, this work aims the development of a methodology using topology optimization techniques for static design of laminated piezocomposite shell structures by considering the optimization of piezoelectric material and polarization distributions together with the optimization of the fiber angle of the composite orthotropic layers, which is free to assume different values along the same composite layer. The finite element model is based on the laminated piezoelectric shell theory, using the degenerate three‐dimensional solid approach and first‐order shell theory kinematics that accounts for the transverse shear deformation and rotary inertia effects. The topology optimization formulation is implemented by combining the piezoelectric material with penalization and polarization model and the discrete material optimization, where the design variables describe the amount of piezoelectric material and polarization sign at each finite element, with the fiber angles, respectively. Three different objective functions are formulated for the design of actuators, sensors, and energy harvesters. Results of laminated piezocomposite shell transducers are presented to illustrate the method. Copyright © 2012 John Wiley & Sons, Ltd.     

Shape control and damage identification of beams using piezoelectric actuation and genetic optimization

This paper deals with the shape control of beams under general loading conditions, using piezoelectric patch actuators that are surface bonded onto beams to provide the control forces. The mathematical formulation of the model is based on the shear deformation beam theory (Timoshenko theory) and the linear theory of piezoelectricity. The numerical solution of the model is based on the development of superconvergent (locking-free) finite elements using the form of the exact solution of the Timoshenko beam theory and Hamilton’s principle. The optimal values for the locations of the piezo-actuators are determined and optimal voltages for shape control are obtained for cantilever beams by using a genetic optimization procedure. Finally, a simplified related damage identification problem is formulated and solved using static data and genetic optimization.     

Optimal design in vibration control of adaptive structures using a simulated annealing algorithm

Advanced reinforced composite structures incorporating piezoelectric sensors and actuators are increasingly becoming important due to the development of smart structures. These structures offer potential benefits in a wide range of engineering applications such as vibration and noise suppression, shape control and precision positioning. This paper presents a finite element formulation based on the classical laminated plate theory for laminated structures with integrated piezoelectric layers or patches, acting as sensors and actuators. The finite element model is a single layer triangular nonconforming plate/shell element with 18 degrees of freedom for the generalized displacements, and one additional electrical potential degree of freedom for each surface bonded piezoelectric element layer or patch. The control is initialized through a previous optimization of the core of the laminated structure, in order to minimize the vibration amplitude and maximize the first natural frequency. Also the optimization of the patches position is performed to maximize the piezoelectric actuators efficiency. The simulated annealing algorithm is used for these purposes. To achieve a mechanism of active control of the structure dynamic response, a feedback control algorithm is used, coupling the sensor and active piezoelectric layers or patches, and to calculate the dynamic response of the laminated structures the Newmark method is considered. The model is applied in the optimization of an illustrative adaptive laminated plate case. The influence of the position and number of piezoelectric patches, as well as the control gain, are investigated and the results are presented and discussed.     

Thermomechanical buckling of hybrid cross-ply laminated rectangular plates

A thermomechanical buckling analysis is presented for simply supported rectangular symmetric cross-ply laminated composite plates that are integrated with surface-mounted piezoelectric actuators and are subjected to the combined action of in-plane compressive edge loads, two types of thermal loads, and constant applied actuator voltage. The formulation of equations is based on the classical laminated plate theory and the von-Karman non-linear kinematic relations. The analysis uses an exact method to obtain closed-form solutions for the buckling load. The effects of applied actuator voltage, thermal and mechanical loads, plate geometry, and lay-up configuration of the laminated plates are investigated. The novelty of the present work is to obtain closed-form solutions for electro-thermomechanical buckling of hybrid composite plates, and to cover non-uniform temperature distribution loading. The results for various states are verified with known data in the literature.