Hydrogenolysis of biomass-derived sorbitol to glycols and glycerol over Ni-MgO catalysts

Ni-MgO catalysts with varying Ni/Mg ratios were prepared by co-precipitation and tested in sorbitol hydrogenolysis. At 473 K and 4 MPa H₂, the best catalyst with Ni/Mg ratio of 3:7 exhibited 67.8% conversion and 80.8% total selectivity of ethylene glycol, 1,2-propylene glycol and glycerol. These catalysts were characterized by XRD, CO₂-TPD and H₂ chemisorption, revealing that the activity depended strongly on the basicity and Ni surface area. The reaction conditions were optimized, which were relatively mild for this chemoselective conversion.     

Hydrogen production via methanol steam reforming over Au/CuO,Au/CeO2, and Au/CuO–CeO2 catalysts prepared by deposition–precipitation

The production of hydrogen (H₂) with a low concentration of carbon monoxide (CO) via steam reforming of methanol (SRM) over Au/CuO, Au/CeO₂, (50:50)CuO–CeO₂, Au/(50:50)CuO–CeO₂, and commercial MegaMax 700 catalysts were investigated over reaction temperatures between 200 °C and 300 °C at atmospheric pressure. Au loading in the catalysts was maintained at 5 wt%. Supports were prepared by co-precipitation (CP) whilst all prepared catalysts were synthesized by deposition–precipitation (DP). The catalysts were characterized by Brunauer–Emmett–Teller (BET) surface area, X-ray diffraction (XRD), temperature-programmed reduction (TPR), and scanning electron microscopy (SEM). Au/(50:50)CuO–CeO₂ catalysts expressed a higher methanol conversion with negligible amount of CO than the others due to the integration of CuO particles into the CeO₂ lattice, as evidenced by XRD, and a interaction of Au and CuO species, as evidenced by TPR. A 50:50 Cu:Ce atomic ratio was optimal for Au supported on CuO–CeO₂ catalysts which can then promote SRM. Increasing the reaction time, by reducing the liquid feed rate from 3 to 1.5 cm³ h^?1, resulted in a catalytic activity with complete (100%) methanol conversion, and a H₂ and CO selectivity of ～82% and ～1.3%, respectively. From stability testing, Au/(50:50)CuO–CeO₂ catalysts were still active for 540 min use even though the CuO was reduced to metallic Cu, as evidenced by XRD. Therefore, it can be concluded that metallic Cu is one of active components of the catalysts for SRM.     

Methanation of carbon dioxide over mesoporous Ni–Fe–Ru–Al2O3 xerogel catalysts: Effect of ruthenium content

Mesoporous nickel (35 wt%)–iron (5 wt%)–ruthenium (x wt%)–alumina xerogel (denoted as 35Ni5FexRuAX) catalysts with different ruthenium contents (x = 0, 0.2, 0.4, 0.6, 0.8, and 1.0) were prepared by a single-step sol–gel method for use in the methane production from CO₂ and H₂. Conversion of CO₂, yield for CH₄, metal surface area, and the amount of desorbed carbon dioxide of the catalysts showed volcano-shaped trends with respect to ruthenium content. Experimental results revealed that metal surface area and the amount of desorbed carbon dioxide of 35Ni5FexRu catalysts were well correlated with conversion of CO₂ and yield for CH₄.     

A novel glass fiber catalyst for the catalytic combustion of ethyl acetate

Supported CuO catalysts were prepared by wet impregnation into novel glass fiber corrugated honeycomb supports, and the catalytic combustion of ethyl acetate and the effect of copper loading were examined. Among the catalysts tested, Cu10/Al₂O₃-M showed the highest activity. For the catalyst, 100% conversion of ethyl acetate was achieved at 300 °C, feed concentration of 1802 mg/m³ and the space velocity of 5000 h^− 1. To reveal these phenomena, the supports and catalysts were characterized by SEM, BET, XRD, H₂-TPR and ethyl acetate-TPD. The catalyst activity was strongly related to the amount of highly dispersed CuO species and suitable porosity.     

Promotional effect of graphite oxide on surface properties and catalytic performance of La1 − xSrxMnO3 (x = 0,0.1) for methane combustion

The effect of graphite oxide (i.e. GO)/La_1 − xSr_xMnO₃ (x = 0,0.1) catalysts on methane combustion in CNG's (compressed natural gas) exhaust was investigated in current work. GO layer was employed to realize a surface modification. The light-off temperature of methane decreased, and reached the full conversion at 540 °C. The prepared catalysts were also characterized by TEM, surface energy, XPS and H₂-TPR techniques. SEM indicated that the La_1 − xSr_xMnO₃ particles grew dispersedly on GO layer, and surface analysis suggested that the introducing of GO can enhance the adsorption of oxygen groups on the surface of the catalysts.     

Effect of the hybrid catalysts preparation method upon direct synthesis of dimethyl ether from synthesis gas

Direct synthesis of DME from synthesis gas attains more attention recently due to higher conversion and lower cost in comparison to dehydration of the methanol. In this work Synthesis gas To Dimethylether (STD) conversion was examined on various hybrid catalysts prepared by seven different methods. These catalysts had the same general form as CuO/ZnO/Al₂O₃ with theoretical weight ratio 31/16/53, respectively. A novel preparation method for hybrid catalyst namely sol–gel impregnation has also been developed which showed better performance in comparison with the other methods. Also, in order to find out the effect of various alumina contents at a fixed CuO/ZnO ratio on the performance of the hybrid catalyst, a series of catalysts with different contents of alumina have been prepared by sol–gel impregnation method. The optimum weight ratio for CuO/ZnO/Al₂O₃ catalyst has been found to be about 2:1:5, respectively. These catalysts characterized by TPR, XRD, XRF, BET, TGA, N₂O absorption. The catalysts performance were tested at 240 °C, 40 bar and space velocity 1000 ml/g_cat.h, with the inlet gas composition H₂/CO/N₂ = 64/32/4 in a micro slurry reactor.     

Catalytic performance of novel Ni catalysts supported on SiC monolithic foam in carbon dioxide reforming of methane to synthesis gas

Carbon dioxide reforming of methane to synthesis gas has been investigated with Ni catalysts supported on SiC monolithic foam. The structure and properties of the catalysts were characterized by BET, SEM and XRD techniques. The novel catalysts exhibited not only the highest activity but also remarkable stability. Of which, 7 wt%Ni/SiC showed the highest activity at 750 °C, During the 100 h performance testing experiment on stream, the conversion of CH₄ and CO₂ remained almost constant, at about 94.0% and 95.0%, respectively.     

Solvent free synthesis of chalcone and flavanone over zinc oxide supported metal oxide catalysts

Liquid phase Claisen–Schmidt condensation between 2′-hydroxyacetophenone and benzaldehyde to form 2′-hydroxychalcone, followed by intramolecular cyclisation to form flavanone was carried out over zinc oxide supported metal oxide catalysts under solvent free condition. The reaction was carried out over ZnO supported MgO, BaO, K₂O and Na₂O catalysts with 0.2 g of each catalyst at 140 °C for 3 h. Magnesium oxide impregnated zinc oxide was observed to offer higher conversion of 2′-hydroxyacetophenone than other catalysts. Further MgO impregnated with various other supports such as HZSM-5, Al₂O₃ and SiO₂ were also used for the reaction to assess the suitability of the support. The order of activity of the support is ZnO > SiO₂ > Al₂O₃ > HZSM-5. Various weight percentage of MgO was loaded on ZnO to optimize maximum efficiency of the catalyst system. The impregnation of MgO (wt%) in ZnO was optimized for better conversion of 2′-hydroxyacetophenone. The effect of temperature and catalyst loading was studied for the reaction.     

Reforming of methane with carbon dioxide over supported bimetallic catalysts containing Ni and noble metal: I. Characterization and activity of SiO2 supported Ni–Rh catalysts

Cobalt catalysts supported on silica aerogel have been prepared using sol–gel chemistry followed by drying under supercritical ethanol conditions. Three different loadings of cobalt were synthesized: 2, 6, and 10% by weight. Transmission electron micrographs indicate that the metallic cobalt exists as discrete particles 50–70 nm in diameter for the 2 and 6% loadings. The 10% catalyst shows long needles of cobalt. BET and BJH measurements indicate that the catalysts retain the silica aerogel properties of high surface area (∼800 m²/g), large pore volume (∼5 cm³/g), and an average pore diameter in the mesoporous regime (∼25 nm). The catalysts were evaluated for Fischer–Tropsch activity in a laboratory-scale packed bed reactor. All three catalysts were active with the 10% Co catalyst achieving more than 20% CO conversion which corresponds to a rate of 1.53 g CO per g-cat per hour. The catalysts were selective for the C₁₀₊ hydrocarbons with more than 50% of the carbon contained within this fraction. A significant portion of the C₉–C₁₅ hydrocarbon product was observed as 1-olefins which reflects the enhanced mass transport within the very porous aerogel support.     

Tungstophosphoric acid supported on titania: A solid acid catalyst in benzylation of phenol with benzylalcohol

Benzylation of phenol with benzylalcohol was carried out in liquid phase over tungstophosphoric acid (TPA) supported on titania. The catalysts were prepared with different TPA (10–25%) loading by wet impregnation method, were calcined at 700 °C and characterized by XRD, surface area, FTIR and acidity of the catalysts was measured by temperature programmed desorption of NH₃–TPD, FTIR pyridine adsorption. The catalysts have been represented by a general formula as xPTiO₂₋y (where x = wt%, P = TPA, and y = calcination temperature in °C). The 20PTiO₂ catalyst calcined at various temperatures to know the effect of calcination temperature on activity of the catalyst and the 20PTiO₂-700 showed highest activity in benzylation of phenol with benzylalcohol because it had highest acidity. The effects of temperature, catalyst weight, mole ratio of the reactants on conversion of phenol and product selectivities have been optimized. 20PTiO₂-700 catalyst gave conversion of benzylalcohol (BA) 98% and the selectivity to benzyl phenol (BP) 83.6%, phenyl benzyl ether (PBE) 9.4%, benzylether (BE) 7% at 130 °C, phenol to benzylalcohol molar ratio 2 and in 1 h.     

Catalytic performance and characterization of Ni-doped HZSM-5 catalysts for selective trimerization of n-butene

A series of Ni-doped HZSM-5 catalysts were prepared and the catalytic performance of these catalysts in n-butene trimerization was investigated. The Ni-loading, the Si/Al ratio of HZSM-5 and the reaction conditions (temperature, pressure and WHSV) played great influences on the catalytic performance of these catalysts in the reaction. 77.5 wt.% conversion of n-butene and 50.5 wt.% selectivity of trimers as well as 19.6 × 10^? 2 g_trimers/(g_cat h) yield of trimers were obtained on 1NiHZSM-5(320) catalyst up to 148 h at 420 °C, WHSV = 2 h^? 1 and 1.0 MPa. In addition, the physicochemical properties of these catalysts were comparatively characterized by powder X-ray diffraction (XRD), N₂ isothermal adsorption–desorption, infrared red spectroscopy (IR) and pyridine adsorbed infrared red spectroscopy (Py-IR) techniques. The doping of Ni into HZSM-5(320) modified the specific surface area and the acidity of these catalysts, which in turn affected the catalytic performance of these catalysts in n-butene trimerization. The acidic amount and the ratio of Lewis/Brönsted acid sites (L/B) on the external surface of these catalysts were close relative to the catalytic performance of these catalysts. 1NiHZSM-5(320) catalyst showed the highest catalytic performance in n-butene trimersization among the investigated catalysts because it had the proper acidic amount and the proper L/B ratio on its external surface.     

Preparation of Mn–FeOx/CNTs catalysts by redox co-precipitation and application in low-temperature NO reduction with NH3

A novel redox co-precipitation method was firstly adopted to prepare the Mn–FeO_x/CNTs catalysts for use in low-temperature NO reduction with NH₃. The catalysts were possessed of amorphous structure and exhibited 80–100% NO conversion at 140–180 °C at a high space velocity of 32,000 h^− 1.     

Influence of CeO2 morphology on the catalytic oxidation of ethanol in air

Nano-CeO₂ catalysts of different shapes were synthesized at different hydrothermal crystallization temperatures from an alkaline aqueous solution. X-ray diffraction (XRD), transmission electron microscope (TEM), and H₂ temperature-programmed reduction (H₂-TPR) were used to study the synthesized nano-CeO₂ catalyst samples. The catalytic properties of the prepared nano-CeO₂ catalysts for the catalytic oxidation of ethanol in air were also investigated. TEM analysis showed that CeO₂ nanorod and nanocube catalysts have been synthesized at hydrothermal crystallization temperatures of 373 K and 453 K, respectively. XRD results showed that the synthesized nano-CeO₂ catalysts have similar cubic fluorite structures. H₂-TPR results indicated that CeO₂ nanorod and nanocube catalysts exhibit different reduction behaviors for H₂ and that the nanorod catalyst has better low-temperature reduction performance than the nanocube catalyst. Ethanol catalytic oxidation results indicated that oxidation and condensation products (including acetaldehyde, acetic acid, CO₂, and ethyl acetate) have been produced from the prepared catalysts. The ethyl acetate and acetic acid can be ignited by ethanol at low temperature on the CeO₂(R) catalyst to give low catalytic combustion temperature for ethyl acetate and acetic acid molecules. CeO₂ nanorods gave ethanol oxidation conversion rates above 99.2% at 443 K and CO₂ selectivity exceeding 99.6% at 483 K, while CeO₂ nanocubes gave ethanol oxidation conversion rates of about 95.1% until 508 K and CO₂ selectivity of only 93.86% at 543 K. CeO₂ nanorod is a potential low-cost and effective catalyst for removing trace amounts of ethanol to purify air.     

The CO methanation over NaY-zeolite supported Ni/Co3O4, Ni/ZrO2, Co3O4/ZrO2 and Ni/Co3O4/ZrO2 catalysts

The CO methanation was studied over zeolite NaY supported Ni, Co₃O₄, ZrO₂ catalysts. The XRD, N₂ physisorption and SEM analysis were used in order to characterize the catalysts. Catalytic activities were carried out under a feed composition of 1% CO, 50% H₂ and 49% He between the 125 °C to 375 °C. Except for the Ni/Co₃O₄/NaY catalyst, all catalysts gave high surface area because of the presence of zeolite NaY. Average pore diameter of the catalysts fell into the mesopore diameter range. The highest CO methanation activity was obtained with Ni/ZrO₂/NaY catalyst at which the CO methanation was started after 175 °C and 100% CO conversion was obtained at 275 °C using the same catalyst.     

Preparation of noble metal nanocatalysts and their applications in catalytic partial oxidation of methane

A series of noble metal catalysts (Ru, Rh, Ir, Pt, and Pd) supported on alumina-stabilized magnesia were prepared and employed in partial oxidation of methane. The prepared catalysts were characterized using BET, SEM, TEM and H₂S chemisorption techniques. The results revealed that the Ru and Rh catalysts had the highest activity in catalytic partial oxidation of methane. Based on the obtained results the following order of activity was observed for different catalysts in partial oxidation of methane: Rh ～ Ru > Ir > Pt > Pd. The obtained results also showed a high catalytic stability without any decrease in methane conversion up to 50 h of reaction.     

Effects of the structure of CeCu catalysts on the catalytic combustion of toluene in air

CeCu composite oxide catalysts were prepared by a hard-template method (CeCu-HT) and a complex method (CeCu-CA). The prepared CeCu composite oxide catalysts were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), and Brunauer–Emmett–Teller (BET) analyses. The catalytic properties of the prepared CeCu composite oxide catalysts were also investigated by the catalytic combustion of toluene in air. XRD results showed that the synthesized CeCu composite oxide catalysts had different phase components and crystallinities but similar CeO₂CuO solid solution phases. Low-angle XRD, TEM, and BET results indicated that the prepared CeCu-HT catalyst had a developed ordered mesoporous structure and a large specific surface area of 206.1 m² g^?1. Toluene catalytic combustion results indicated that the CeCu-HT catalyst had higher toluene catalytic combustion activity in air than the CeCu-CA catalyst. The minimum reaction temperature at which toluene conversion exceeded 90% for toluene catalytic combustion on the CeCu-HT catalyst was 225 °C. The toluene catalytic combustion conversion on the CeCu-HT catalyst at 240 °C exceeded 99.3% with decreased toluene concentration in air to below 70 ppm. On the other hand, the toluene catalytic combustion conversion on the CeCu-CA catalyst was only 92% even when the reaction temperature reached 280 °C. The differences between the toluene catalytic combustion performances of the CeCu composite oxide catalysts prepared by different methods can be attributed to their discrepant compositions and structures.     

Zirconia-supported niobia catalyzed formation of propanol from 1,2-propanediol via dehydration and consecutive hydrogen transfer

Vapor-phase catalytic dehydration of 1,2-propanediol was investigated over Zirconia-supported niobia catalysts. The catalysts exhibit selectivity favoring propanol (approximately 39%) at 85.0% 1,2-propanediol conversion at 290 °C under 1 atm N₂. The ZrNbO catalysts were analyzed by various techniques; the results indicated that the active sites were weak Brønsted acid sites. A dehydration and hydrogen transfer mechanism was also proposed.     

Promoting effect of rhenium on catalytic performance of Ru catalysts in hydrogenolysis of glycerol to propanediol

Ru/Al₂O₃, Ru/C and Ru/ZrO₂ catalysts were applied to the hydrogenolysis of glycerol to propanediol, and the effect of Re as an additive on the catalytic performance of Ru catalysts was examined. The catalyst systems were characterized by N₂ adsorption/desorption, XRD, TEM-EDX and XPS. The hydrogenolysis of glycerol was carried out under the conditions of 120–180 °C, 4–10 MPa hydrogen pressure and 4–8 h, and the conversion of glycerol varied from 18.7% to 29.7% over Ru/Al₂O₃, Ru/C and Ru/ZrO₂ catalysts. The reaction results indicate that Re possesses high promoting effect on the catalytic performance of Ru catalysts in glycerol hydrogenolysis.     

Electrodeposited Re-promoted Ni foams as a catalyst for the dry reforming of methane

The dry reforming of methane (DRM) utilizes carbon dioxide (CO₂) as the oxidizing agent in order to produce synthesis gas. Catalyst deactivation via coking, oxidation, and sintering has stymied the industrialization of catalysts for the DRM. Here, we utilized electrodeposition followed by de-alloying in order to synthesize metal alloy foams (5 m²/g). Through this process we have created the first electrodeposited DRM catalyst capable of converting more than 10,000 mL/g 1 h at near-equilibrium conversion. Rhenium promotion was observed over the entire temperature range studied (700–800 °C), with the most dramatic enhancement at 700 °C. After 50 h of reaction, no significant accumulation of carbonaceous deposits were detected, making electrodeposited structures a viable candidate for stable methane conversion catalysts.     

Oxidative dehydrogenation of 1-butene to 1,3-butadiene over BiFe0.65NixMo oxide catalysts: Effect of nickel content

BiFe_0.65Ni_xMo oxide catalysts (x = 0–0.2) were prepared and applied for the oxidative dehydrogenation of butenes to 1,3-butadiene. Temperature programmed reoxidation (TPRO) measurements revealed that the catalytic activity was closely related to the oxygen mobility. The surface modification by small amounts of nickel addition is favorable in this reaction. Among the catalysts studied here, BiFe_0.65Ni_0.05Mo oxide catalyst showed the highest conversion and BD yield (X = 86% and Y_BD = 72%) due to the high oxygen mobility. The BiFe_0.65Ni_0.05Mo oxide catalyst is very stable and no deactivation during the 100 h reaction was shown.