Low‐Temperature Growth of All‐Carbon Graphdiyne on a Silicon Anode for High‐Performance Lithium‐Ion Batteries

In situ weaving an all‐carbon graphdiyne coat on a silicon anode is scalably realized under ultralow temperature (25 °C). This economical strategy not only constructs 3D all‐carbon mechanical and conductive networks with reasonable voids for the silicon anode at one time but also simultaneously forms a robust interfacial contact among the electrode components. The intractable problems of the disintegrations in the mechanical and conductive networks and the interfacial contact caused by repeated volume variations during cycling are effectively restrained. The as‐prepared electrode demostrates the advantages of silicon regarding capacity (4122 mA h g^?1 at 0.2 A g^?1) with robust capacity retention (1503 mA h g^?1) after 1450 cycles at 2 A g^?1, and a commercial‐level areal capacity up to 4.72 mA h cm^?2 can be readily approached. Furthermore, this method shows great promises in solving the key problems in other high‐energy‐density anodes.     

Scalable 2D Mesoporous Silicon Nanosheets for High‐Performance Lithium‐Ion Battery Anode

Constructing unique mesoporous 2D Si nanostructures to shorten the lithium‐ion diffusion pathway, facilitate interfacial charge transfer, and enlarge the electrode–electrolyte interface offers exciting opportunities in future high‐performance lithium‐ion batteries. However, simultaneous realization of 2D and mesoporous structures for Si material is quite difficult due to its non‐van der Waals structure. Here, the coexistence of both mesoporous and 2D ultrathin nanosheets in the Si anodes and considerably high surface area (381.6 m² g^?1) are successfully achieved by a scalable and cost‐efficient method. After being encapsulated with the homogeneous carbon layer, the Si/C nanocomposite anodes achieve outstanding reversible capacity, high cycle stability, and excellent rate capability. In particular, the reversible capacity reaches 1072.2 mA h g^?1 at 4 A g^?1 even after 500 cycles. The obvious enhancements can be attributed to the synergistic effect between the unique 2D mesoporous nanostructure and carbon capsulation. Furthermore, full‐cell evaluations indicate that the unique Si/C nanostructures have a great potential in the next‐generation lithium‐ion battery. These findings not only greatly improve the electrochemical performances of Si anode, but also shine some light on designing the unique nanomaterials for various energy devices.     

Novel 2D Layered Molybdenum Ditelluride Encapsulated in Few‐Layer Graphene as High‐Performance Anode for Lithium‐Ion Batteries

Molybdenum ditelluride nanosheets encapsulated in few‐layer graphene (MoTe₂/FLG) are synthesized by a simple heating method using Te and Mo powder and subsequent ball milling with graphite. The as‐prepared MoTe₂/FLG nanocomposites as anode materials for lithium‐ion batteries exhibit excellent electrochemical performance with a highly reversible capacity of 596.5 mAh g^?1 at 100 mA g^?1, a high rate capability (334.5 mAh g^?1 at 2 A g^?1), and superior cycling stability (capacity retention of 99.5% over 400 cycles at 0.5 A g^?1). Ex situ X‐ray diffraction and transmission electron microscopy are used to explore the lithium storage mechanism of MoTe₂. Moreover, the electrochemical performance of a MoTe₂/FLG//0.35Li₂MnO₃·0.65LiMn_0.5Ni_0.5O₂ full cell is investigated, which displays a reversible capacity of 499 mAh g^?1 (based on the MoTe₂/FLG mass) at 100 mA g^?1 and a capacity retention of 78% over 50 cycles, suggesting the promising application of MoTe₂/FLG for lithium‐ion storage. First‐principles calculations exhibit that the lowest diffusion barrier (0.18 eV) for lithium ions along pathway III in the MoTe₂ layered structure is beneficial for improving the Li intercalation/deintercalation property.     

Preparation of MoS2‐Coated Three‐Dimensional Graphene Networks for High‐Performance Anode Material in Lithium‐Ion Batteries

A novel composite, MoS₂‐coated three‐dimensional graphene network (3DGN), referred to as MoS₂/3DGN, is synthesized by a facile CVD method. The 3DGN, composed of interconnected graphene sheets, not only serves as template for the deposition of MoS₂, but also provides good electrical contact between the current collector and deposited MoS₂. As a proof of concept, the MoS₂/3DGN composite, used as an anode material for lithium‐ion batteries, shows excellent electrochemical performance, which exhibits reversible capacities of 877 and 665 mAh g^?1 during the 50^th cycle at current densities of 100 and 500 mA g^?1, respectively, indicating its good cycling performance. Furthermore, the MoS₂/3DGN composite also shows excellent high‐current‐density performance, e.g., depicts a 10^th‐cycle capacity of 466 mAh g^?1 at a high current density of 4 A g^?1.     

Glucose‐Induced Synthesis of 1T‐MoS2/C Hybrid for High‐Rate Lithium‐Ion Batteries

1T phase MoS₂ possesses higher conductivity than the 2H phase, which is a key parameter of electrochemical performance for lithium ion batteries (LIBs). Herein, a 1T‐MoS₂/C hybrid is successfully synthesized through facile hydrothermal method with a proper glucose additive. The synthesized hybrid material is composed of smaller and fewer‐layer 1T‐MoS₂ nanosheets covered by thin carbon layers with an enlarged interlayer spacing of 0.94 nm. When it is used as an anode material for LIBs, the enlarged interlayer spacing facilitates rapid intercalating and deintercalating of lithium ions and accommodates volume change during cycling. The high intrinsic conductivity of 1T‐MoS₂ also contributes to a faster transfer of lithium ions and electrons. Moreover, much smaller and fewer‐layer nanosheets can shorten the diffusion path of lithium ions and accelerate reaction kinetics, leading to an improved electrochemical performance. It delivers a high initial capacity of 920.6 mAh g^?1 at 1 A g^?1 and the capacity can maintain 870 mAh g^?1 even after 300 cycles, showing a superior cycling stability. The electrode presents a high rate performance as well with a reversible capacity of 600 mAh g^?1 at 10 A g^?1. These results show that the 1T‐MoS₂/C hybrid shows potential for use in high‐performance lithium‐ion batteries.     

Flexible 3D Porous MXene Foam for High‐Performance Lithium‐Ion Batteries

2D transition‐metal carbides and nitrides, named MXenes, are promising materials for energy storage, but suffer from aggregation and restacking of the 2D nanosheets, which limits their electrochemical performance. In order to overcome this problem and realize the full potential of MXene nanosheets, a 3D MXene foam with developed porous structure is established via a simple sulfur‐template method, which is freestanding, flexible, and highly conductive, and can be directly used as the electrode in lithium‐ion batteries. The 3D porous architecture of the MXene foam offers massive active sites to enhance the lithium storage capacity. Moreover, its foam structure facilitates electrolyte infiltration for fast Li⁺ transfer. As a result, this flexible 3D porous MXene foam exhibits significantly enhanced capacity of 455.5 mAh g^?1 at 50 mA g^?1, excellent rate performance (101 mAh g^?1 at 18 A g^?1), and superior ultralong‐term cycle stability (220 mAh g^?1 at 1 A g^?1 after 3500 cycles). This work not only demonstrates the great superiority of the 3D porous MXene foam but also proposes the sulfur‐template method for controllable constructing of the 3D foam from 2D nanosheets at a relatively low temperature.     

Graphene Caging Silicon Particles for High‐Performance Lithium‐Ion Batteries

Silicon holds great promise as an anode material for lithium‐ion batteries with higher energy density; its implication, however, is limited by rapid capacity fading. A catalytic growth of graphene cages on composite particles of magnesium oxide and silicon, which are made by magnesiothermic reduction reaction of silica particles, is reported herein. Catalyzed by the magnesium oxide, graphene cages can be conformally grown onto the composite particles, leading to the formation of hollow graphene‐encapsulated Si particles. Such materials exhibit excellent lithium storage properties in terms of high specific capacity, remarkable rate capability (890 mAh g^?1 at 5 A g^?1), and good cycling retention over 200 cycles with consistently high coulombic efficiency at a current density of 1 A g^?1. A full battery test using LiCoO₂ as the cathode demonstrates a high energy density of 329 Wh kg^?1.     

An Advanced MoS2/Carbon Anode for High‐Performance Sodium‐Ion Batteries

Molybdenum disulfide (MoS₂) is a promising anode for high performance sodium‐ion batteries due to high specific capacity, abundance, and low cost. However, poor cycling stability, low rate capability and unclear electrochemical reaction mechanism are the main challenges for MoS₂ anode in Na‐ion batteries. In this study, molybdenum disulfide/carbon (MoS₂/C) nanospheres are fabricated and used for Na‐ion battery anodes. MoS₂/C nanospheres deliver a reversible capacity of 520 mAh g^?1 at 0.1 C and maintain at 400 mAh g^?1 for 300 cycles at a high current density of 1 C, demonstrating the best cycling performance of MoS₂ for Na‐ion batteries to date. The high capacity is attributed to the short ion and electron diffusion pathway, which enables fast charge transfer and low concentration polarization. The stable cycling performance and high coulombic efficiency (～100%) of MoS₂/C nanospheres are ascribed to (1) highly reversible conversion reaction of MoS₂ during sodiation/desodiation as evidenced by ex‐situ X‐ray diffraction (XRD) and (2) the formation of a stable solid electrolyte interface (SEI) layer in fluoroethylene carbonate (FEC) based electrolyte as demonstrated by fourier transform infrared spectroscopy (FTIR) measurements.     

Recent Development in Separators for High‐Temperature Lithium‐Ion Batteries

Lithium‐ion batteries (LIBs) are promising energy storage devices for integrating renewable resources and high power applications, owing to their high energy density, light weight, high flexibility, slow self‐discharge rate, high rate charging capability, and long battery life. LIBs work efficiently at ambient temperatures, however, at high‐temperatures, they cause serious issues due to the thermal fluctuation inside batteries during operation. The separator is a key component of batteries and is crucial for the sustainability of LIBs at high‐temperatures. The high thermal stability with minimum thermal shrinkage and robust mechanical strength are the prime requirements along with high porosity, ionic conductivity, and electrolyte uptake for highly efficient high‐temperature LIBs. This Review deals with the recent studies and developments in separator technologies for high‐temperature LIBs with respect to their structural layered formation. The recent progress in monolayer and multilayer separators along with the developed preparation methodologies is discussed in detail. Future challenges and directions toward the advancement in separator technology are also discussed for achieving remarkable performance of separators in a high‐temperature environment.     

A High‐Performance Lithium‐Ion Capacitor Based on 2D Nanosheet Materials

Lithium‐ion capacitors (LICs) are promising electrical energy storage systems for mid‐to‐large‐scale applications due to the high energy and large power output without sacrificing long cycle stability. However, due to the different energy storage mechanisms between anode and cathode, the energy densities of LICs often degrade noticeably at high power density, because of the sluggish kinetics limitation at the battery‐type anode side. Herein, a high‐performance LIC by well‐defined ZnMn₂O₄‐graphene hybrid nanosheets anode and N‐doped carbon nanosheets cathode is presented. The 2D nanomaterials offer high specific surface areas in favor of a fast ion transport and storage with shortened ion diffusion length, enabling fast charge and discharge. The fabricated LIC delivers a high specific energy of 202.8 Wh kg^?1 at specific power of 180 W kg^?1, and the specific energy remains 98 Wh kg^?1 even when the specific power achieves as high as 21 kW kg^?1.     

MOF‐Derived CuS@Cu‐BTC Composites as High‐Performance Anodes for Lithium‐Ion Batteries

The CuS(x wt%)@Cu‐BTC (BTC = 1,3,5‐benzenetricarboxylate; x = 3, 10, 33, 58, 70, 99.9) materials are synthesized by a facile sulfidation reaction. The composites are composed of octahedral Cu₃(BTC)₂·(H₂O)₃ (Cu‐BTC) with a large specific surface area and CuS with a high conductivity. The as‐prepared CuS@Cu‐BTC products are first applied as the anodes of lithium‐ion batteries (LIBs). The synergistic effect between Cu‐BTC and CuS components can not only accommodate the volume change and stress relaxation of electrodes but also facilitate the fast transport of Li ions. Thus, it can greatly suppress the transformation process from Li₂S to polysulfides by improving the reversibility of the conversion reaction. Benefiting from the unique structural features, the optimal CuS(70 wt%)@Cu‐BTC sample exhibits a remarkably improved electrochemical performance, showing an over‐theoretical capacity up to 1609 mAh g^?1 after 200 cycles (100 mA g^?1) with an excellent rate‐capability of ≈490 mAh g^?1 at 1000 mA g^?1. The outstanding LIB properties indicate that the CuS(70 wt%)@Cu‐BTC sample is a highly desirable electrode material candidate for high‐performance LIBs.